One of the main advantages of disc brakes over drum brakes is that the disc brake : U. Can stop a vehicle in a shorter distance V. Is more heat resistant W. Weighs less than drum brakes X. Requires less pedal force to stop the vehicle

One of the main advantages of disc brakes over drum brakes is that the disc brake :  U. Can stop a vehicle in a shorter distance  
V. Is more heat resistant  
W. Weighs less than drum brakes  
X. Requires less pedal force to stop the vehicle
by

1 Answer

Answer :

. Requires less pedal force to stop the vehicle
by

Related questions

Stopping distance of vehicles : When brakes are applied to a moving vehicle, the distance it travels before stopping is called stopping distance. It is an important factor for road safety and depends on the initial velocity ( v 0 ) and the braking capacity, or deceleration, ?a that is caused by the braking. A car travelling at speed 72km/hr suddenly applies the brake with the deceleration of 5m/s2. Find the stopping distance of the car -Science

Description : Stopping distance of vehicles : When brakes are applied to a moving vehicle, the distance it travels before stopping is called stopping distance. It is an important factor for road safety and depends on ... the brake with the deceleration of 5m/s2. Find the stopping distance of the car -Science

Last Answer : Here u=72 km/hr = 72×10003600m/s=2072×10003600m/s=20 m/s , v=0 a= -5 m/s2 Now using the relation v2=u2+2asv2=u2+2as 0=(20)2+2×(−5)×s0=(20)2+2×(−5)×s s=40ms=40m

The ability of a driver to stop the vehicle moving with the designed speed, depends upon: (A) Perception time (B) Brake reaction time (C) Efficiency of the brakes (D) All the above

Description : The ability of a driver to stop the vehicle moving with the designed speed, depends upon: (A) Perception time (B) Brake reaction time (C) Efficiency of the brakes (D) All the above

Last Answer : Answer: Option D

when you fully depress a brake pedal of a vehicle with abs, you will feel -General Knowledge

Description : when you fully depress a brake pedal of a vehicle with abs, you will feel -General Knowledge

Last Answer : When you fully depress a brake pedal of a vehicle with ABS you will feel: a pulse.

In an offset disc harrow the angle between two gang is a) less than 90 degree b) 90 degree c) greater than 90 degree d) 180degree

Description : In an offset disc harrow the angle between two gang is a) less than 90 degree b) 90 degree c) greater than 90 degree d) 180degree

Last Answer : a) less than 90 degre

ln single action disc harrow the two gangs are at set single a) less than 90 degree b) at 90 degree c) greater than 90 degree d) at 180 degree

Description : n single action disc harrow the two gangs are at set single a) less than 90 degree b) at 90 degree c) greater than 90 degree d) at 180 degree

Last Answer : c) greater than 90 degree

The following is not a drum brake (A) External contracting brake (B) Internal expanding brake (C) Disc brake (D) All of the above

Description : The following is not a drum brake (A) External contracting brake (B) Internal expanding brake (C) Disc brake (D) All of the above

Last Answer : (C) Disc brake

Differentiate between Drum and Disc brake with justification.

Description : Differentiate between Drum and Disc brake with justification.

Last Answer : Sr.No . Disc Brake  Drum brake  1 Friction surfaces are directly exposed to the cooling air.  Friction occurs on the internal surfaces, therefore heat dissipated only by conduction ... More frictional area  10 Pressure intensity is more Pressure intensity is less 

the distance you travel from seeing the danger to putting your foot on the brake pedal is known as: -General Knowledge

Description : the distance you travel from seeing the danger to putting your foot on the brake pedal is known as: -General Knowledge

Last Answer : The distance you travel from seeing the danger to putting your foot on the brake pedal is known as reaction distance.

Most important factor affecting threshing efficiency a)peripheral speed of the drum b)cylinder concave clearance c)moisture content of crop d)feed rate

Description : Most important factor affecting threshing efficiency a)peripheral speed of the drum b)cylinder concave clearance c)moisture content of crop d)feed rate

Last Answer : a)peripheral speed of the drum

Kinematic index of the straw Walker is as ratio (a) Angular velocity of straw Walker to angular velocity of threshing drum (b) Angular velocity of straw Walker to angular velocity of threshing drum (c) Angular velocity of straw Walker to linear velocity of combine (d) All of the above

Description : Kinematic index of the straw Walker is as ratio (a) Angular velocity of straw Walker to angular velocity of threshing drum (b) Angular velocity of straw Walker to angular velocity of threshing drum (c) Angular velocity of straw Walker to linear velocity of combine (d) All of the above

Last Answer : (a) Angular velocity of straw Walker to angular velocity of threshing drum

Blades of disc harrow are sharpened from the_______ side penetrate more readily than blades sharpened from the__________ side a) convex, concave c) concave, convex b) Front, rear d) Rear, front

Description : Blades of disc harrow are sharpened from the_______ side penetrate more readily than blades sharpened from the__________ side a) convex, concave c) concave, convex b) Front, rear d) Rear, front

Last Answer : c) concave, convex

Rated speed of an engine is the speed at which an engine devlopes (A) Maximum crankshaft torque (B) Maximum brake horse power output (C) Maximum thermal efficiency (D) Maximum drawback pull

Description : Rated speed of an engine is the speed at which an engine devlopes (A) Maximum crankshaft torque (B) Maximum brake horse power output (C) Maximum thermal efficiency (D) Maximum drawback pull

Last Answer : (B) Maximum brake horse power output

Which one is a transmission dynamometer a) Torsion dynamometer b) Froues hydraulic dynamometer c) Belr dynamometer d) Proney brake dynamometer

Description : Which one is a transmission dynamometer a) Torsion dynamometer b) Froues hydraulic dynamometer c) Belr dynamometer d) Proney brake dynamometer

Last Answer : a) Torsion dynamometer

Width of cut of disc plow is increased by a)Increasing disc angle b)Increasing tilt angle c)addition of more weight d)Decreasing disc angle

Description : Width of cut of disc plow is increased by a)Increasing disc angle b)Increasing tilt angle c)addition of more weight d)Decreasing disc angle

Last Answer : a)Increasing disc angle

Which end of disc harrow tends to penetrate more deeply a) Concave b) Convex c) Rear d) Front

Description : Which end of disc harrow tends to penetrate more deeply a) Concave b) Convex c) Rear d) Front

Last Answer : a) Concave

When frequency of occurrence of overload is less and magnitude of overload is also less than safety device used is a) Safety jump clutch b) Shear device c) Frictional device d) V-belt drive

Description : When frequency of occurrence of overload is less and magnitude of overload is also less than safety device used is a) Safety jump clutch b) Shear device c) Frictional device d) V-belt drive

Last Answer : a) Safety jump clutch

When frequency of occurrence of overload is less but the mangnitude of overload is large than safety device used is: a) Safety jump clutch b) Shear device c) Frictional device d) V-belt drive

Description : When frequency of occurrence of overload is less but the mangnitude of overload is large than safety device used is: a) Safety jump clutch b) Shear device c) Frictional device d) V-belt drive

Last Answer : b) Shear device

1Heavy draft of a disc plough is due to: A. Blunt disc B. Furrows too wide C. Loose bearings D. All are currect

Description : 1Heavy draft of a disc plough is due to: A. Blunt disc B. Furrows too wide C. Loose bearings D. All are currect

Last Answer : D. All are currect

The implement which can work in offset position a)offset disc harrow b) mower c) both (a) and (b) d) none of the above

Description : The implement which can work in offset position a)offset disc harrow b) mower c) both (a) and (b) d) none of the above

Last Answer : c) both (a) and (b)

Land shaping becomes essential where often the following implement is used a) M.B. Plough b) Disc plough c) Cultivator d) All of the above

Description : Land shaping becomes essential where often the following implement is used a) M.B. Plough b) Disc plough c) Cultivator d) All of the above

Last Answer : a) M.B. Plough

Which end of the disc harrow penetrates deeply a) Concave b) Convex c) Rear d) Front

Description : Which end of the disc harrow penetrates deeply a) Concave b) Convex c) Rear d) Front

Last Answer : a) Concave

Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type c) Spike tooth d) Hammer mill

Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type c) Spike tooth d) Hammer mill

Last Answer : a) Raspbar type cylinder

0ff-set disc harrows are best suitable to work for a) primary implement b) breaking clods c) orchard cultivation d) surface finishing

Description : 0ff-set disc harrows are best suitable to work for a) primary implement b) breaking clods c) orchard cultivation d) surface finishing

Last Answer : c) orchard cultivation

In standard disc plow the tilk angel varies between: A.30-40 ° B.40-45° C.20-25° D.2-3°

Description : In standard disc plow the tilk angel varies between: A.30-40 ° B.40-45° C.20-25° D.2-3°

Last Answer : C.20-25°

In a disc plough with the increase in the disk angle, the transverse component of reaction will a)Increase b) Decrease c) Unaffected d) None of the above

Description : In a disc plough with the increase in the disk angle, the transverse component of reaction will a)Increase b) Decrease c) Unaffected d) None of the above

Last Answer : a)Increase

The two types of cylinder used on power wheat threshers are: a) Serrated disc and rasp bar b) Spike tooth and wire loop type c) Spike tooth and hammer mill d) Hammer mill and flails

Description : The two types of cylinder used on power wheat threshers are: a) Serrated disc and rasp bar b) Spike tooth and wire loop type c) Spike tooth and hammer mill d) Hammer mill and flails

Last Answer : c) Spike tooth and hammer mill

The depth of penetration of a disc harrow is increased by: a) Tilt angle b) Gang angle c) Disc angle d) All of above

Description : The depth of penetration of a disc harrow is increased by: a) Tilt angle b) Gang angle c) Disc angle d) All of above

Last Answer : b) Gang angle

The two primery tillage equipment a. MB plough and disc harrow b. Disc plough and disc harrow c. Disc harrow and cultivetor d. MB plough and subsoiler

Description : The two primery tillage equipment a. MB plough and disc harrow b. Disc plough and disc harrow c. Disc harrow and cultivetor d. MB plough and subsoiler

Last Answer : d. MB plough and subsoiler

Dead furrow is made by: a. One way MB plough b. Two way MB plough c. Ridger d. Disc harrow

Description : Dead furrow is made by: a. One way MB plough b. Two way MB plough c. Ridger d. Disc harrow

Last Answer : a. One way MB plough

A coulter attachment is used with: a. Disc harrow b. Seed drill c. MB plough d. Sub soiler

Description : A coulter attachment is used with: a. Disc harrow b. Seed drill c. MB plough d. Sub soiler

Last Answer : c. MB ploug

Disc angle adjustment influences: a. Depth of cut b. width of cut c. Soil break up d. Direction of travel

Description : Disc angle adjustment influences: a. Depth of cut b. width of cut c. Soil break up d. Direction of travel

Last Answer : b. width of cut

.Land shipping become necessary often the following implments is used: a. MB plough b. Disc harrow c. Cultivator d. All of these

Description : .Land shipping become necessary often the following implments is used: a. MB plough b. Disc harrow c. Cultivator d. All of these

Last Answer : a. MB plough

Land shaping becomes essential where often the following implement is used a) M.B. Plough b) Disc Harrow c) Cultivator d) All of the above

Description : Land shaping becomes essential where often the following implement is used a) M.B. Plough b) Disc Harrow c) Cultivator d) All of the above

Last Answer : a) M.B. Plough

Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type cylinder c) Spike tooth d) Hammer mill

Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type cylinder c) Spike tooth d) Hammer mill

Last Answer : a) Raspbar type cylinder

Heavy draft of a disc plough is due to: a) Blunt disc b) Furrows too wide c) Loose bearings d) All of the above

Description : Heavy draft of a disc plough is due to: a) Blunt disc b) Furrows too wide c) Loose bearings d) All of the above

Last Answer : d) All of the above

The type of bearing generally used to support the discs on a standard disc plough is: A. Ball bearing. B. Tapered roller bearing. C. Plain roller bearing. D. Bush bearing.

Description : The type of bearing generally used to support the discs on a standard disc plough is: A. Ball bearing. B. Tapered roller bearing. C. Plain roller bearing. D. Bush bearing.

Last Answer : B. Tapered roller bearing.

.Laying out of field in lands is essential when working with a. Two way plough b. One way plough c. Disc harrow d. Cultivator

Description : .Laying out of field in lands is essential when working with a. Two way plough b. One way plough c. Disc harrow d. Cultivator

Last Answer : b. One way plough

Disc type furrow openers are especially suited to A. Stoney and root infested soils B. Poorly prepared bed in trashy soil C. Hard and sticky soil with considerable amount of debris and mulch D. All of the above

Description : Disc type furrow openers are especially suited to A. Stoney and root infested soils B. Poorly prepared bed in trashy soil C. Hard and sticky soil with considerable amount of debris and mulch D. All of the above

Last Answer : C. Hard and sticky soil with considerable amount of debris and mulch

Tapper roller bearing are used in disc harrow because a) It can take heavy radial loads b) It can take both radial as well as end thrust c) It can operate effectively at low speed and in contact with dirt d) Both (b) and (c) are true

Description : Tapper roller bearing are used in disc harrow because a) It can take heavy radial loads b) It can take both radial as well as end thrust c) It can operate effectively at low speed and in contact with dirt d) Both (b) and (c) are true

Last Answer : d) Both (b) and (c) are true

Penetration of disc plough can be improved by a) Increase disc angle b) Decreasing tilt angle c) Both (a) and (b) d) None of the above

Description : Penetration of disc plough can be improved by a) Increase disc angle b) Decreasing tilt angle c) Both (a) and (b) d) None of the above

Last Answer : b) Decreasing tilt angle

At smaller disc angles , the draft tends to increase in disc plough because of a) Greater contact area between furrow wall and the convex side of the disc b) Increase in the side draft c) Greater throw of the soil d) All of the above

Description : At smaller disc angles , the draft tends to increase in disc plough because of a) Greater contact area between furrow wall and the convex side of the disc b) Increase in the side draft c) Greater throw of the soil d) All of the above

Last Answer : a) Greater contact area between furrow wall and the convex side of the disc

V -belt are most suitable for a. less space requirements b. use with adjustable pulley foe speed change c. both (a) and (b) d. none of the above

Description : V -belt are most suitable for a. less space requirements b. use with adjustable pulley foe speed change c. both (a) and (b) d. none of the above

Last Answer : c. both (a) and (b)

Center of resistence of a mould board plow less at distance equal to A. 1/4th the size of plow from the share wing B. 3/4th the size of plow from the share wing C. 2/3th the size of plow from the share wing D. 1/3th the size of plow from the share wing

Description : Center of resistence of a mould board plow less at distance equal to A. 1/4th the size of plow from the share wing B. 3/4th the size of plow from the share wing C. 2/3th the size of plow from the share wing D. 1/3th the size of plow from the share wing

Last Answer : B. 3/4th the size of plow from the share wing

A car is moving along a straight horizontal road at a speed of 20 meters per second. The brakes are applied and a constant force of 5000 Newtons decelerates the car to a stop in 10 seconds. The mass of the car is: w) 1250 kilograms x) 2500 kilograms y) 5000 kilograms z) 10,000 kilograms

Description : A car is moving along a straight horizontal road at a speed of 20 meters per second. The brakes are applied and a constant force of 5000 Newtons decelerates the car to a stop in 10 seconds. The mass of the car is: w) 1250 kilograms x) 2500 kilograms y) 5000 kilograms z) 10,000 kilograms

Last Answer : ANSWER: X -- 2500 KILOGRAMS

Farming operation which requires maximum energy a.) Sowing b.) Interculture c.) Tillage d.) Harvesting

Description : Farming operation which requires maximum energy a.) Sowing b.) Interculture c.) Tillage d.) Harvesting

Last Answer : c.) Tillage

Foam spraying requires special type of nozzle A. Flat fan nozzle B. Flooding nozzle C. Hollow cone nozzle D. Air aspiring nozzle

Description : Foam spraying requires special type of nozzle A. Flat fan nozzle B. Flooding nozzle C. Hollow cone nozzle D. Air aspiring nozzle

Last Answer : D. Air aspiring nozzle

The size of a seed rill is expressed by: A. Amount of seed sown per unit time. B. Length x width of the machine. C. Area covered per unit time. D. The number of furrow openers x distance between two furrow

Description : The size of a seed rill is expressed by: A. Amount of seed sown per unit time. B. Length x width of the machine. C. Area covered per unit time. D. The number of furrow openers x distance between two furrow

Last Answer : D. The number of furrow openers x distance between two furrow

Why is the brake pedal in the new Buick Regal so squishy?

Description : Why is the brake pedal in the new Buick Regal so squishy?

Last Answer : Sounds like BS to me. The only times my brake pedal went to the floor were after losing a brake line and half my brake fluid.

What is meant by brake pedal pads?

Description : What is meant by brake pedal pads?

Last Answer : It would be the rubber pad that sits on your brake pedal. Unless they were referring to brake pads, which are the pads which enables your vehicle to stop by pressing the brake pedal.

In comparison to jump clutchs, advantages of the friction safety clutches is/are a) More consistent break away torque b) No damageing peak during slippage c) Protecting a drive from high freuency peak torque (2-3 time normal values) d) All of the above

Description : In comparison to jump clutchs, advantages of the friction safety clutches is/are a) More consistent break away torque b) No damageing peak during slippage c) Protecting a drive from high freuency peak torque (2-3 time normal values) d) All of the above

Last Answer : d) All of the above