Hook link chains are a)suitable for external drive exposed atmosphere b)made of meabble iron c)used where power requirement is low and speed is low d)All of the above

Hook link chains are
a)suitable for external drive exposed atmosphere
b)made of meabble iron
c)used where power requirement is low and speed is low
d)All of the above
by

1 Answer

Answer :

d)All of the above
by

Related questions

Roller chains are used for: a)Higher speed and higher loads b)made of high grade steel c)components are harden and polished d)All of the above

Description : Roller chains are used for: a)Higher speed and higher loads b)made of high grade steel c)components are harden and polished d)All of the above

Last Answer : d)All of the above

A power tiller is relatively more suitable for : A. Puddling of low land paddy fields with a rotary tiller B. Primary tillage of upland paddy fields with a rotary tillers C. Primary tillage with a mould board plough D. Farm transportation work

Description : A power tiller is relatively more suitable for : A. Puddling of low land paddy fields with a rotary tiller B. Primary tillage of upland paddy fields with a rotary tillers C. Primary tillage with a mould board plough D. Farm transportation work

Last Answer : A. Puddling of low land paddy fields with a rotary tiller

Rotary tillers are characterized by a) Lower and negative draft b) High power requirement c) Excessive pulverization d) All the above

Description : Rotary tillers are characterized by a) Lower and negative draft b) High power requirement c) Excessive pulverization d) All the above

Last Answer : d) All the above

pecific energy requirement of rotary tillers can be reduce by a) Increasing the bite length b) Decreasing depth to diameter ratio c) Both (a) and (b) d) Excessive reduction in total power requirement

Description : pecific energy requirement of rotary tillers can be reduce by a) Increasing the bite length b) Decreasing depth to diameter ratio c) Both (a) and (b) d) Excessive reduction in total power requirement

Last Answer : c) Both (a) and (b)

Hook type blades best suited for e. Minimum tillage of trashy land at shallow depths f. Dried hard soils g. Cutting and pulverisation especially in wet sticky clay soil h. Working under normal field conditions

Description : Hook type blades best suited for e. Minimum tillage of trashy land at shallow depths f. Dried hard soils g. Cutting and pulverisation especially in wet sticky clay soil h. Working under normal field conditions

Last Answer : f. Dried hard soils

For operating rotavator on trashy soils which tines are better: A L-shaped B.Hook shaped C.Backward curved tip twist blade D.Straight blade

Description : For operating rotavator on trashy soils which tines are better: A L-shaped B.Hook shaped C.Backward curved tip twist blade D.Straight blade

Last Answer : A L-shaped

V -belt are most suitable for a. less space requirements b. use with adjustable pulley foe speed change c. both (a) and (b) d. none of the above

Description : V -belt are most suitable for a. less space requirements b. use with adjustable pulley foe speed change c. both (a) and (b) d. none of the above

Last Answer : c. both (a) and (b)

Transplanter using soil bearing seedlings are more popular than washed root seedling transplanter because of a) less labour requirement b) lesser plant missing percentage c) higher work rates d) all of the above

Description : Transplanter using soil bearing seedlings are more popular than washed root seedling transplanter because of a) less labour requirement b) lesser plant missing percentage c) higher work rates d) all of the above

Last Answer : d) all of the above

Rotary tiller are wide adopted in rice cultivation due to a) Excessive pulverization b) Suitability for pudding paddy field c) Reduced draft requirement d) Complete inversion of soil

Description : Rotary tiller are wide adopted in rice cultivation due to a) Excessive pulverization b) Suitability for pudding paddy field c) Reduced draft requirement d) Complete inversion of soil

Last Answer : b) Suitability for pudding paddy field

owest specific energy requirement for the operation of rotavator is about _______ times as great as a mould board plough working in the same soil. a) Equal b) Twice c) Three d) Four

Description : owest specific energy requirement for the operation of rotavator is about _______ times as great as a mould board plough working in the same soil. a) Equal b) Twice c) Three d) Four

Last Answer : c) Three

rank speed on the mower with conventional pit man drive is a)850-1000 rpm b)1000-1200rpm c)800-1150rpm d)1200-1600 rpm

Description : rank speed on the mower with conventional pit man drive is a)850-1000 rpm b)1000-1200rpm c)800-1150rpm d)1200-1600 rpm

Last Answer : a)850-1000 rpm

V-belt drive transmission system is used when it is designed to achieve a) High speed ratio b) Space requirements are limited c) Both (a) and (b) d) None of the above

Description : V-belt drive transmission system is used when it is designed to achieve a) High speed ratio b) Space requirements are limited c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

Detonation is favoured by a. Low crankshaft speed at full throttle b. .Higher loads c. Both (a) and (b) d. None of the above

Description : Detonation is favoured by a. Low crankshaft speed at full throttle b. .Higher loads c. Both (a) and (b) d. None of the above

Last Answer : c. Both (a) and (b)

iesel engine has less reserve torque then spark ignition because ∙ Torque-speed curve is governed by volumetric efficiency of fuel pump and engine cylinder ∙ Torque is a function of thermal efficiency ∙ Diesel engine has generally low speed engine ∙ None of the above

Description : iesel engine has less reserve torque then spark ignition because ∙ Torque-speed curve is governed by volumetric efficiency of fuel pump and engine cylinder ∙ Torque is a function of thermal efficiency ∙ Diesel engine has generally low speed engine ∙ None of the above

Last Answer : ∙ Torque is a function of thermal efficiency

Tapper roller bearing are used in disc harrow because a) It can take heavy radial loads b) It can take both radial as well as end thrust c) It can operate effectively at low speed and in contact with dirt d) Both (b) and (c) are true

Description : Tapper roller bearing are used in disc harrow because a) It can take heavy radial loads b) It can take both radial as well as end thrust c) It can operate effectively at low speed and in contact with dirt d) Both (b) and (c) are true

Last Answer : d) Both (b) and (c) are true

Speed of a low speed engine is (a) <350 rpm (b) 350-1000 rpm (c) >1000rpm (d) none of the above

Description : Speed of a low speed engine is (a) 1000rpm (d) none of the above

Last Answer : (a)

Needle bearing a roller bearing having a number of smaller diameter roller is well suited to a) Application involving oscillating motion b) Exceptionally high load capacity application at low peripheral speed c) Both (a) and (b) d) None of the above

Description : Needle bearing a roller bearing having a number of smaller diameter roller is well suited to a) Application involving oscillating motion b) Exceptionally high load capacity application at low peripheral speed c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

.The land side of a mould board plough is made of: A. Malleable iron B. Forged steel C. C45 steel D. Soft Centre steel

Description : .The land side of a mould board plough is made of: A. Malleable iron B. Forged steel C. C45 steel D. Soft Centre steel

Last Answer : D. Soft Centre steel

Share for use in sandy soils are made of A)chilled cast iron. B)cast iron C)mild steel. D)gun metal

Description : Share for use in sandy soils are made of A)chilled cast iron. B)cast iron C)mild steel. D)gun metal

Last Answer : Share for use in sandy soils are made of A)chilled cast iron. B)cast iron C)mild steel. D)gun metal

The landside of a mould board plough is made of: a) Malleable iron b) Forged steel c) C45 steel d) Soft centre steel

Description : The landside of a mould board plough is made of: a) Malleable iron b) Forged steel c) C45 steel d) Soft centre steel

Last Answer : d) Soft centre steel

Mould board are usually made from a. Soft centre steel b. Hardened carbon steel c. Chilled cast iron d. Mild steel

Description : Mould board are usually made from a. Soft centre steel b. Hardened carbon steel c. Chilled cast iron d. Mild steel

Last Answer : a. Soft centre steel

0ff-set disc harrows are best suitable to work for a) primary implement b) breaking clods c) orchard cultivation d) surface finishing

Description : 0ff-set disc harrows are best suitable to work for a) primary implement b) breaking clods c) orchard cultivation d) surface finishing

Last Answer : c) orchard cultivation

Lister plows especially suitable for a.) Dry land agriculture. b.) Breaking hard pan. c.) Earthing plants. d.) Mulching.

Description : Lister plows especially suitable for a.) Dry land agriculture. b.) Breaking hard pan. c.) Earthing plants. d.) Mulching.

Last Answer : a.) Dry land agriculture.

The metering mechanism which is suitable for the metering of small seeds as well as large grains. (a) Internal double run mechanism (b) Fluted wheel mechanism (c) Stationary opening with auger (d) None of the above

Description : The metering mechanism which is suitable for the metering of small seeds as well as large grains. (a) Internal double run mechanism (b) Fluted wheel mechanism (c) Stationary opening with auger (d) None of the above

Last Answer : (a) Internal double run mechanism

The metering mechanism which is most suitable for metering of small seed is to handle is a. Internal double run mechanism b. Fluted wheel mechanism c. Stationery opening with agitator d. None of the above

Description : The metering mechanism which is most suitable for metering of small seed is to handle is a. Internal double run mechanism b. Fluted wheel mechanism c. Stationery opening with agitator d. None of the above

Last Answer : b. Fluted wheel mechanism

Optimum speed for grains like gram,pea,etc.,thresher using power is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Description : Optimum speed for grains like gram,pea,etc.,thresher using power is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Last Answer : a) 300-400rpm

Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Description : Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Last Answer : d) 1100-1200rpm

Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm

Description : Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm

Last Answer : c) 600-800rpm

Rated speed of an engine is the speed at which an engine devlopes (A) Maximum crankshaft torque (B) Maximum brake horse power output (C) Maximum thermal efficiency (D) Maximum drawback pull

Description : Rated speed of an engine is the speed at which an engine devlopes (A) Maximum crankshaft torque (B) Maximum brake horse power output (C) Maximum thermal efficiency (D) Maximum drawback pull

Last Answer : (B) Maximum brake horse power output

Slip of belt is responsible for A. Reduction is speed B. Reduction in power C. Reduction in belt life D. All of the above

Description : Slip of belt is responsible for A. Reduction is speed B. Reduction in power C. Reduction in belt life D. All of the above

Last Answer : D. All of the above

Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

Description : Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

Last Answer : Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

Cylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peripheral speed N. Concave clearance O. Blower speed P. All of the above

Description : Cylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peCylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peripheral speed N. Concave clearance O. Blower speed P. All of the above

Last Answer : M. Cylinder peripheral speed

Speed of power operated machine chaff cutter is E. 35 rpm F. 50 rpm G. 600-1000 rpm H. None of the above

Description : Speed of power operated machine chaff cutter is E. 35 rpm F. 50 rpm G. 600-1000 rpm H. None of the above

Last Answer : G. 600-1000 rpm

A power tiller is most suited for rotary cultivation because: A. It generates negative draft B. Its traction requirements are low C. It provides high degree of soil pulverization D. All of the above

Description : A power tiller is most suited for rotary cultivation because: A. It generates negative draft B. Its traction requirements are low C. It provides high degree of soil pulverization D. All of the above

Last Answer : D. All of the above

Lewis formula is used in the design of a) gears b) clutch c) chain drive d) belt drives

Description : Lewis formula is used in the design of a) gears b) clutch c) chain drive d) belt drives

Last Answer : a) gears

Belt Tension can be adjusted by a. idler pulley b. slide rails c. tilting plate drive d. all the above

Description : Belt Tension can be adjusted by a. idler pulley b. slide rails c. tilting plate drive d. all the above

Last Answer : d. all the above

Tension on the slack side in chain drive is A)more than on tight side. B)less than on tight side. C)zero. D)equal to tight

Description : Tension on the slack side in chain drive is A)more than on tight side. B)less than on tight side. C)zero. D)equal to tight

Last Answer : C)zero

Desired tension in an open belt drive system can be maintained (without changing center to center distance between two pulley)by using A)ldler pulley. B)slide rail C) Tilting angle. D)none of the above

Description : Desired tension in an open belt drive system can be maintained (without changing center to center distance between two pulley)by using A)ldler pulley. B)slide rail C) Tilting angle. D)none of the above

Last Answer : A)ldler pulley

When V-belt drive is used a safety device, its performance is affected by a) Variation in belt tention b) Increase in coefficient of friction as belt slippage increase c) Both (a) and (b) d) None of the above

Description : When V-belt drive is used a safety device, its performance is affected by a) Variation in belt tention b) Increase in coefficient of friction as belt slippage increase c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

In comparison to jump clutchs, advantages of the friction safety clutches is/are a) More consistent break away torque b) No damageing peak during slippage c) Protecting a drive from high freuency peak torque (2-3 time normal values) d) All of the above

Description : In comparison to jump clutchs, advantages of the friction safety clutches is/are a) More consistent break away torque b) No damageing peak during slippage c) Protecting a drive from high freuency peak torque (2-3 time normal values) d) All of the above

Last Answer : d) All of the above

When frequency of occurrence of overload is less and magnitude of overload is also less than safety device used is a) Safety jump clutch b) Shear device c) Frictional device d) V-belt drive

Description : When frequency of occurrence of overload is less and magnitude of overload is also less than safety device used is a) Safety jump clutch b) Shear device c) Frictional device d) V-belt drive

Last Answer : a) Safety jump clutch

When frequency of occurrence of overload is less but the mangnitude of overload is large than safety device used is: a) Safety jump clutch b) Shear device c) Frictional device d) V-belt drive

Description : When frequency of occurrence of overload is less but the mangnitude of overload is large than safety device used is: a) Safety jump clutch b) Shear device c) Frictional device d) V-belt drive

Last Answer : b) Shear device

Differential lock offers advantage of A. Better drawbar pull when drive wheel are under different conditions B. Easier to plant in straight rows C. Reduces stearing effort and side draft when operating with certain implements D. All of the above

Description : Differential lock offers advantage of A. Better drawbar pull when drive wheel are under different conditions B. Easier to plant in straight rows C. Reduces stearing effort and side draft when operating with certain implements D. All of the above

Last Answer : D. All of the above

Tension on slack side in case of chain drive a) Lesser than on tight side b) Greater than on tight side c) Zero d) Equal to that on tight side

Description : Tension on slack side in case of chain drive a) Lesser than on tight side b) Greater than on tight side c) Zero d) Equal to that on tight side

Last Answer : c) Zero

Carbon content in the cast iron is (A) 2.5 – 4.5 % (B) 0 – 0.25 % (C) 0.25 – 0.50 % (D) 0.50 – 1.5 %

Description : Carbon content in the cast iron is (A) 2.5 – 4.5 % (B) 0 – 0.25 % (C) 0.25 – 0.50 % (D) 0.50 – 1.5 %

Last Answer : (B) 0 – 0.25 %

- Material used for hand slide is (a) chilled cast iron. (b) cast iron (c) mild steel. (d) gun metal

Description : - Material used for hand slide is (a) chilled cast iron. (b) cast iron (c) mild steel. (d) gun metal

Last Answer : (c) mild steel

The average working speed of a hand operated chaff fitted with two knives is _________ rev/min.

Description : The average working speed of a hand operated chaff fitted with two knives is _________ rev/min.

Last Answer : 35

In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.

Description : In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.

Last Answer : 1200 to 1500

main function of the current regulator is A. To prevent the reversal flow of current from the battery when dynamo speed is drops. B. To safeguard against flow of high currents to battery when armature develops more current. C. To prevent building up of high voltage in a circuit. D. None of the above

Description : main function of the current regulator is A. To prevent the reversal flow of current from the battery when dynamo speed is drops. B. To safeguard against flow of high currents to battery when armature develops ... . C. To prevent building up of high voltage in a circuit. D. None of the above

Last Answer : B. To safeguard against flow of high currents to battery when armature develops more current.

Main function of cutout relay in electrical circuit is A. To prevent the reversal of current flow from the battery when dynamo speed (engine speed) reduces. B. To restrict the maximum output at high speed. C. To permit the generation to deliver current to the battery or to the lightening and ignition circuit. D. None of the above

Description : Main function of cutout relay in electrical circuit is A. To prevent the reversal of current flow from the battery when dynamo speed (engine speed) reduces. B. To restrict the maximum output at ... deliver current to the battery or to the lightening and ignition circuit. D. None of the above

Last Answer : A. To prevent the reversal of current flow from the battery when dynamo speed (engine speed) reduces.