When V-belt drive is used a safety device, its performance is affected by a) Variation in belt tention b) Increase in coefficient of friction as belt slippage increase c) Both (a) and (b) d) None of the above

When V-belt drive is used a safety device, its performance is affected by  a) Variation in belt tention  
b) Increase in coefficient of friction as belt slippage increase
c) Both (a) and (b)
d) None of the above
by

1 Answer

Answer :

c) Both (a) and (b)
by

Related questions

In comparison to jump clutchs, advantages of the friction safety clutches is/are a) More consistent break away torque b) No damageing peak during slippage c) Protecting a drive from high freuency peak torque (2-3 time normal values) d) All of the above

Description : In comparison to jump clutchs, advantages of the friction safety clutches is/are a) More consistent break away torque b) No damageing peak during slippage c) Protecting a drive from high freuency peak torque (2-3 time normal values) d) All of the above

Last Answer : d) All of the above

When frequency of occurrence of overload is less and magnitude of overload is also less than safety device used is a) Safety jump clutch b) Shear device c) Frictional device d) V-belt drive

Description : When frequency of occurrence of overload is less and magnitude of overload is also less than safety device used is a) Safety jump clutch b) Shear device c) Frictional device d) V-belt drive

Last Answer : a) Safety jump clutch

When frequency of occurrence of overload is less but the mangnitude of overload is large than safety device used is: a) Safety jump clutch b) Shear device c) Frictional device d) V-belt drive

Description : When frequency of occurrence of overload is less but the mangnitude of overload is large than safety device used is: a) Safety jump clutch b) Shear device c) Frictional device d) V-belt drive

Last Answer : b) Shear device

310- Larger tension ratio result in... (a) Unnecessary high tension in belt (b) Reduction in belt life (c) Excessive belt slippage (d) Increase belt life

Description : 310- Larger tension ratio result in... (a) Unnecessary high tension in belt (b) Reduction in belt life (c) Excessive belt slippage (d) Increase belt life

Last Answer : (c) Excessive belt slippage

Smaller tension ratio result in.... (a) Unnecessary high tension in belt (b) Reduction in belt life (c) Both (c) & (b) (d) Excessive belt slippage

Description : Smaller tension ratio result in.... (a) Unnecessary high tension in belt (b) Reduction in belt life (c) Both (c) & (b) (d) Excessive belt slippage

Last Answer : (c) Both (c) & (b)

V-belt drive transmission system is used when it is designed to achieve a) High speed ratio b) Space requirements are limited c) Both (a) and (b) d) None of the above

Description : V-belt drive transmission system is used when it is designed to achieve a) High speed ratio b) Space requirements are limited c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

V -belt are most suitable for a. less space requirements b. use with adjustable pulley foe speed change c. both (a) and (b) d. none of the above

Description : V -belt are most suitable for a. less space requirements b. use with adjustable pulley foe speed change c. both (a) and (b) d. none of the above

Last Answer : c. both (a) and (b)

.308- Life expectancy of V-belt in farm machinery is about.... (a) 200-500 hrs (b) 1000-2000 hrs (c) 2000-5000hrs (d) 5000-10000hrs

Description : .308- Life expectancy of V-belt in farm machinery is about.... (a) 200-500 hrs (b) 1000-2000 hrs (c) 2000-5000hrs (d) 5000-10000hrs

Last Answer : (b) 1000-2000 hrs

Variation in the drop size of seed can be minimised by (a) Using a short, smooth, small diameter tube with the discharge end close to bottom of furrow. (b) Discharging the seed directly from the metering device within a few centimetres of the furrow bottom. (c) Mechanically transferring the seeds from the metering unit in the furrow. (d) All of the above.

Description : Variation in the drop size of seed can be minimised by (a) Using a short, smooth, small diameter tube with the discharge end close to bottom of furrow. (b) Discharging the seed directly from ... (c) Mechanically transferring the seeds from the metering unit in the furrow. (d) All of the above.

Last Answer : d) All of the above.

Lewis formula is used in the design of a) gears b) clutch c) chain drive d) belt drives

Description : Lewis formula is used in the design of a) gears b) clutch c) chain drive d) belt drives

Last Answer : a) gears

Belt Tension can be adjusted by a. idler pulley b. slide rails c. tilting plate drive d. all the above

Description : Belt Tension can be adjusted by a. idler pulley b. slide rails c. tilting plate drive d. all the above

Last Answer : d. all the above

Desired tension in an open belt drive system can be maintained (without changing center to center distance between two pulley)by using A)ldler pulley. B)slide rail C) Tilting angle. D)none of the above

Description : Desired tension in an open belt drive system can be maintained (without changing center to center distance between two pulley)by using A)ldler pulley. B)slide rail C) Tilting angle. D)none of the above

Last Answer : A)ldler pulley

Function of idler pully are a. to increase the angle of contact of belt on pully b. maintain belt tension as belt stretches c. canter to centre distance remain same d. all the above

Description : Function of idler pully are a. to increase the angle of contact of belt on pully b. maintain belt tension as belt stretches c. canter to centre distance remain same d. all the above

Last Answer : d. all the above

knives of the cutter bar are scrratedin order to a)Increase the co-efficient of friction between crop stalk machine b)Reducing the deflection of stalk side ways c)To increase the cutting speed d)To improve cutting height

Description : knives of the cutter bar are scrratedin order to a)Increase the co-efficient of friction between crop stalk machine b)Reducing the deflection of stalk side ways c)To increase the cutting speed d)To improve cutting height

Last Answer : a)Increase the co-efficient of friction between crop stalk machine

Length of open belt is given by formula a. L=[2C+( 2) (DI+D2)] + [ /4C] b. L=[2C+( 2) (DI+D2)] + [ /4C] c. L=[2C+( 2) (DI+D2)] + [ ] d. L=[2C+( 2) (DI D2)] + [ ]

Description : Length of open belt is given by formula a. L=[2C+( 2) (DI+D2)] + [ /4C] b. L=[2C+( 2) (DI+D2)] + [ /4C] c. L=[2C+( 2) (DI+D2)] + [ ] d. L=[2C+( 2) (DI D2)] + [ ]

Last Answer : a. L=[2C+( 2) (DI+D2)] + [ /4C]

Slip of belt is responsible for A. Reduction is speed B. Reduction in power C. Reduction in belt life D. All of the above

Description : Slip of belt is responsible for A. Reduction is speed B. Reduction in power C. Reduction in belt life D. All of the above

Last Answer : D. All of the above

What is the value for centrifugal torque for maximum power transmission in belt drives a) ½ maximum torque b) 2/3 maximum torque c) ¾ maximum torque d) None of the above

Description : What is the value for centrifugal torque for maximum power transmission in belt drives a) ½ maximum torque b) 2/3 maximum torque c) ¾ maximum torque d) None of the above

Last Answer : d) None of the above

An erratic variation of speed governor when it is over compensated for speed changes is a) Governor strength b) Governor regulation c) Governor hunting

Description : An erratic variation of speed governor when it is over compensated for speed changes is a) Governor strength b) Governor regulation c) Governor hunting

Last Answer : c) Governor hunting

Scouring will occur as long as a) Frictional resistance at soil tool interface is less than the resistance at parallel soil-soil inter face b) Frictional resistance at soil tool interface is more than the resistance at parallel soil-soil inter face c) Soil-metal friction is more than angle of soil shearing resistance d) None of the above

Description : Scouring will occur as long as a) Frictional resistance at soil tool interface is less than the resistance at parallel soil-soil inter face b) Frictional resistance at soil tool interface is more than ... c) Soil-metal friction is more than angle of soil shearing resistance d) None of the above

Last Answer : a) Frictional resistance at soil tool interface is less than the resistance at parallel soil-soil inter face

Force ( including rolling resistance friction ) that acts upon the stabilising surfaces such landslide and sole of bottom are called a) Useful soil resistance b) Parasitic force d) Draft of implement. d) Pull of implement

Description : Force ( including rolling resistance friction ) that acts upon the stabilising surfaces such landslide and sole of bottom are called a) Useful soil resistance b) Parasitic force d) Draft of implement. d) Pull of implement

Last Answer : b) Parasitic force

Volumetric efficiency is affected by (A) Turbulence velocity and temperature of intake manifold (B) Efficiency of exhaust stroke (C) Valve timing overlap (D) All the above

Description : Volumetric efficiency is affected by (A) Turbulence velocity and temperature of intake manifold (B) Efficiency of exhaust stroke (C) Valve timing overlap (D) All the above

Last Answer : (D) All the above

Application rate of sprayer is affected by a. forward of speed b. number of nozzle c. rate of discharge d. all of the above

Description : Application rate of sprayer is affected by a. forward of speed b. number of nozzle c. rate of discharge d. all of the above

Last Answer : d. all of the above

For rotary cutting blade the proper cutting quality is affected by A)rates of forward speed to blade pert pheral speed B)radius of rotation of cutting blade C)feed per blade D)all of these

Description : For rotary cutting blade the proper cutting quality is affected by A)rates of forward speed to blade pert pheral speed B)radius of rotation of cutting blade C)feed per blade D)all of these

Last Answer : D)all of these

Cell fill is affected by (a) Seed size (b) Cell speed (c) Cell size (d) All of the above

Description : Cell fill is affected by (a) Seed size (b) Cell speed (c) Cell size (d) All of the above

Last Answer : d) All of the above

Capacity of field choppers (chaff cutter) is affected by.... (a) Capacity of the feed mechanism (cross-sectional area) (b) Rate of advance of material through throat considered as to be same linear speed of feed mechanism (c) Density of forage material (d) All of the above

Description : Capacity of field choppers (chaff cutter) is affected by.... (a) Capacity of the feed mechanism (cross-sectional area) (b) Rate of advance of material through throat considered as to be same linear speed of feed mechanism (c) Density of forage material (d) All of the above

Last Answer : (d) All of the above

Cut-off device is not required with (a) Inclined plate metering (b) Horizontally plate metering (c) Vertically plate metering (d) All of the above

Description : Cut-off device is not required with (a) Inclined plate metering (b) Horizontally plate metering (c) Vertically plate metering (d) All of the above

Last Answer : (a) Inclined plate metering

Most commonly used metering device for bulk flow seed metering of small and medium size seeds (grains) a) Fluted wheel b) Internal double run c) Stationary opening with agitator d) None of the above

Description : Most commonly used metering device for bulk flow seed metering of small and medium size seeds (grains) a) Fluted wheel b) Internal double run c) Stationary opening with agitator d) None of the above

Last Answer : a) Fluted wheel

Air output of a duster is given by formula a) Q= 60×A×V b)Q= 60×A×(2GH/Y) c) Q= 240×A×h d) all of the above

Description : Air output of a duster is given by formula a) Q= 60×A×V b)Q= 60×A×(2GH/Y) c) Q= 240×A×h d) all of the above

Last Answer : d) all of the above

One of the main advantages of disc brakes over drum brakes is that the disc brake : U. Can stop a vehicle in a shorter distance V. Is more heat resistant W. Weighs less than drum brakes X. Requires less pedal force to stop the vehicle

Description : One of the main advantages of disc brakes over drum brakes is that the disc brake : U. Can stop a vehicle in a shorter distance V. Is more heat resistant W. Weighs less than drum brakes X. Requires less pedal force to stop the vehicle

Last Answer : . Requires less pedal force to stop the vehicle

The formula for tension difference or effective pull, required to transmit the load at.... (a) (Tt-Ts)=1000(kw/V) (b) Tt/Ts=c^ke (c) (Tt-Ts)= 1000(Hp/V) (d) None of the above

Description : The formula for tension difference or effective pull, required to transmit the load at.... (a) (Tt-Ts)=1000(kw/V) (b) Tt/Ts=c^ke (c) (Tt-Ts)= 1000(Hp/V) (d) None of the above

Last Answer : (a) (Tt-Ts)=1000(kw/V)

V-shaped sweeps are best suited for a ) Primary tillage b) Stubble mulch tillage c) Rotary tillage d) Minimum tillage

Description : V-shaped sweeps are best suited for a ) Primary tillage b) Stubble mulch tillage c) Rotary tillage d) Minimum tillage

Last Answer : b) Stubble mulch tillage

Tension on the slack side in chain drive is A)more than on tight side. B)less than on tight side. C)zero. D)equal to tight

Description : Tension on the slack side in chain drive is A)more than on tight side. B)less than on tight side. C)zero. D)equal to tight

Last Answer : C)zero

Hook link chains are a)suitable for external drive exposed atmosphere b)made of meabble iron c)used where power requirement is low and speed is low d)All of the above

Description : Hook link chains are a)suitable for external drive exposed atmosphere b)made of meabble iron c)used where power requirement is low and speed is low d)All of the above

Last Answer : d)All of the above

Differential lock offers advantage of A. Better drawbar pull when drive wheel are under different conditions B. Easier to plant in straight rows C. Reduces stearing effort and side draft when operating with certain implements D. All of the above

Description : Differential lock offers advantage of A. Better drawbar pull when drive wheel are under different conditions B. Easier to plant in straight rows C. Reduces stearing effort and side draft when operating with certain implements D. All of the above

Last Answer : D. All of the above

rank speed on the mower with conventional pit man drive is a)850-1000 rpm b)1000-1200rpm c)800-1150rpm d)1200-1600 rpm

Description : rank speed on the mower with conventional pit man drive is a)850-1000 rpm b)1000-1200rpm c)800-1150rpm d)1200-1600 rpm

Last Answer : a)850-1000 rpm

Tension on slack side in case of chain drive a) Lesser than on tight side b) Greater than on tight side c) Zero d) Equal to that on tight side

Description : Tension on slack side in case of chain drive a) Lesser than on tight side b) Greater than on tight side c) Zero d) Equal to that on tight side

Last Answer : c) Zero

Increasing non grain feed rate increase (a) Cylinder losses (b) Seed damage (c) Both (a) and(b) (d) None of the above

Description : Increasing non grain feed rate increase (a) Cylinder losses (b) Seed damage (c) Both (a) and(b) (d) None of the above

Last Answer : (a) Cylinder losses

Penetration of disc plough can be improved by a) Increase disc angle b) Decreasing tilt angle c) Both (a) and (b) d) None of the above

Description : Penetration of disc plough can be improved by a) Increase disc angle b) Decreasing tilt angle c) Both (a) and (b) d) None of the above

Last Answer : b) Decreasing tilt angle

A slat mould board scours better than a solid mould board because of smaller contact area resulting in a) Reduction of adhesive force b) Increase in soil pressure c) Both (a) and (b) d) None of the above

Description : A slat mould board scours better than a solid mould board because of smaller contact area resulting in a) Reduction of adhesive force b) Increase in soil pressure c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

Increasing non-grain feed rate increase a) Cylinder losses b) seed damage c)Both (a) and (b) d) none of the above

Description : Increasing non-grain feed rate increase a) Cylinder losses b) seed damage c)Both (a) and (b) d) none of the above

Last Answer : a) Cylinder losses

According to Darcy's formula, the loss of head due to friction in the pipe is (where f = Darcy's coefficient, l = Length of pipe, v = Velocity of liquid in pipe, and d = Diameter of pipe) (A) flv²/2gd (B) flv²/gd (C) 3flv²/2gd (D) 4flv²/2gd

Description : According to Darcy's formula, the loss of head due to friction in the pipe is (where f = Darcy's coefficient, l = Length of pipe, v = Velocity of liquid in pipe, and d = Diameter of pipe) (A) flv²/2gd (B) flv²/gd (C) 3flv²/2gd (D) 4flv²/2gd

Last Answer : Answer: Option D

swirl plate in the cone nozzle is provided to. a. Impart rotational motion to the liquid passing through it. b. To increase the droplet size. c. To decrease the droplet size. d. To increase the spray angle.

Description : swirl plate in the cone nozzle is provided to. a. Impart rotational motion to the liquid passing through it. b. To increase the droplet size. c. To decrease the droplet size. d. To increase the spray angle.

Last Answer : a. Impart rotational motion to the liquid passing through it.

.Increase length of a land slide of a one bottom right hand mould board plough will a) Increase the amount of offset on tractor b) Decrease the amount of offset c) No affect d) Affect Completely

Description : .Increase length of a land slide of a one bottom right hand mould board plough will a) Increase the amount of offset on tractor b) Decrease the amount of offset c) No affect d) Affect Completely

Last Answer : c) No affect

Durability of the fertilizer increases with a) Increase in the kinetic angle of repose b) Decrease in the kinetic angle of repose c) Decrease in the speed of the forward travel d) None of the above

Description : Durability of the fertilizer increases with a) Increase in the kinetic angle of repose b) Decrease in the kinetic angle of repose c) Decrease in the speed of the forward travel d) None of the above

Last Answer : b) Decrease in the kinetic angle of repose

In a disc plough with the increase in the disk angle, the transverse component of reaction will a)Increase b) Decrease c) Unaffected d) None of the above

Description : In a disc plough with the increase in the disk angle, the transverse component of reaction will a)Increase b) Decrease c) Unaffected d) None of the above

Last Answer : a)Increase

.total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

Description : .total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

Last Answer : .total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

A thresh causes more seed damage if :- a. Seed is increase b. Clearance is increased c. Feed rate is reduced d. Seed is reduced

Description : A thresh causes more seed damage if :- a. Seed is increase b. Clearance is increased c. Feed rate is reduced d. Seed is reduced

Last Answer : a. Seed is increase

Increasing the cylinder speed result in (a) Increase threshing efficiency (b) Reduce cylinder loss (c) Increase seed damage (d) All of the above

Description : Increasing the cylinder speed result in (a) Increase threshing efficiency (b) Reduce cylinder loss (c) Increase seed damage (d) All of the above

Last Answer : (a) Increase threshing efficiency

.Increase the grain/non grain ratio on the shoe tends to the shoe losses (a) Decreases (b) Increases (c) Decrease or increase (d) Equal

Description : .Increase the grain/non grain ratio on the shoe tends to the shoe losses (a) Decreases (b) Increases (c) Decrease or increase (d) Equal

Last Answer : (d) Equal

.Incresase amount of the non grain material on the straw Walker the walker (a) Decrease (b) Increase (c) Unaffected (d) Equal

Description : .Incresase amount of the non grain material on the straw Walker the walker (a) Decrease (b) Increase (c) Unaffected (d) Equal

Last Answer : b) Increase