Cylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peripheral speed N. Concave clearance O. Blower speed P. All of the above

Cylinder loss in a stationary power thresher can be reduced by increasing the :  M. Cylinder peCylinder loss in a stationary power thresher can be reduced by increasing the :  M. Cylinder peripheral speed  
N. Concave clearance  
O. Blower speed  
P. All of the above
by

1 Answer

Answer :

M. Cylinder peripheral speed
by

Related questions

Thresher blows broken grains with chaff due to a) Higher cylinder speed. b) More feed Rate c) More cylinder concave clearance d) Moisture content of the crop is more

Description : Thresher blows broken grains with chaff due to a) Higher cylinder speed. b) More feed Rate c) More cylinder concave clearance d) Moisture content of the crop is more

Last Answer : a) Higher cylinder speed.

Adjustment needed when thresher blows grains with chaff a.) Decreasing cylinder peripheral speed. b.) Increasing cylinder speed. c.) Decreasing feed rate. d.) Increasing cylinder

Description : Adjustment needed when thresher blows grains with chaff a.) Decreasing cylinder peripheral speed. b.) Increasing cylinder speed. c.) Decreasing feed rate. d.) Increasing cylinder

Last Answer : a.) Decreasing cylinder peripheral speed.

Most important factor affecting threshing efficiency a)peripheral speed of the drum b)cylinder concave clearance c)moisture content of crop d)feed rate

Description : Most important factor affecting threshing efficiency a)peripheral speed of the drum b)cylinder concave clearance c)moisture content of crop d)feed rate

Last Answer : a)peripheral speed of the drum

The threshing efficiency of thresher depends on a) Cylinder peripheral speed b) Cylinder concave clearance c) Feed rate, moisture content and type of crop d) All are correct

Description : The threshing efficiency of thresher depends on a) Cylinder peripheral speed b) Cylinder concave clearance c) Feed rate, moisture content and type of crop d) All are correct

Last Answer :  All are correct

Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Description : Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Last Answer : d) 1100-1200rpm

.total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

Description : .total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

Last Answer : .total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.

Description : In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.

Last Answer : 1200 to 1500

Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type c) Spike tooth d) Hammer mill

Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type c) Spike tooth d) Hammer mill

Last Answer : a) Raspbar type cylinder

Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type cylinder c) Spike tooth d) Hammer mill

Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type cylinder c) Spike tooth d) Hammer mill

Last Answer : a) Raspbar type cylinder

Axial flow thresher utilises (a) Rasp bar cylinder (b) Spike tooth cylinder (c) Hammer mill cylinder (d) Peg tooth cylinder

Description : Axial flow thresher utilises (a) Rasp bar cylinder (b) Spike tooth cylinder (c) Hammer mill cylinder (d) Peg tooth cylinder

Last Answer : (b) Spike tooth cylinder

Increasing the cylinder speed result in (a) Increase threshing efficiency (b) Reduce cylinder loss (c) Increase seed damage (d) All of the above

Description : Increasing the cylinder speed result in (a) Increase threshing efficiency (b) Reduce cylinder loss (c) Increase seed damage (d) All of the above

Last Answer : (a) Increase threshing efficiency

Increasing the cylinder speed result in a) Increase threshing efficiency b) Reduce cylinder loss c) Increase seed damage d) All of the above

Description : Increasing the cylinder speed result in a) Increase threshing efficiency b) Reduce cylinder loss c) Increase seed damage d) All of the above

Last Answer : d) All of the above

A threshing cylinder of 15cm radius is rotating at 700rpm if peripheral velocity (m/sec) will be a. 11 b.105 c. 210 d. 660

Description : A threshing cylinder of 15cm radius is rotating at 700rpm if peripheral velocity (m/sec) will be a. 11 b.105 c. 210 d. 660

Last Answer : a. 11

In a thresher, by increasing the speed of threshing cylinder a) Threshing efficiency can be increased b) Broken grain loss can be minimized c) Un-threshed grains can be increased d) Straw breakup can be increased Ans. a

Description : In a thresher, by increasing the speed of threshing cylinder a) Threshing efficiency can be increased b) Broken grain loss can be minimized c) Un-threshed grains can be increased d) Straw breakup can be increased Ans. a

Last Answer : ans a

Optimum speed for grains like gram,pea,etc.,thresher using power is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Description : Optimum speed for grains like gram,pea,etc.,thresher using power is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Last Answer : a) 300-400rpm

thresher causes more seed damage if: a speed is increased b clearance increased c speed is decreased d feed rate is reduced

Description : thresher causes more seed damage if: a speed is increased b clearance increased c speed is decreased d feed rate is reduced

Last Answer : a speed is increased

A thresher causes more seed damage if 1. Speed is increased 2. Clearance is increased 3. Feed rate is reduced 4. speed is reduced

Description : A thresher causes more seed damage if 1. Speed is increased 2. Clearance is increased 3. Feed rate is reduced 4. speed is reduced

Last Answer : ans 1

The thresher caused More seed damage if A. Speed is increases B. Clearance is increase C. Feed rate is reduced. D. Speed is reduced

Description : The thresher caused More seed damage if A. Speed is increases B. Clearance is increase C. Feed rate is reduced. D. Speed is reduced

Last Answer : Speed is increases

A thresh causes more seed damage if :- a. Seed is increase b. Clearance is increased c. Feed rate is reduced d. Seed is reduced

Description : A thresh causes more seed damage if :- a. Seed is increase b. Clearance is increased c. Feed rate is reduced d. Seed is reduced

Last Answer : a. Seed is increase

Curved twisted blades are specially suited for m. Minimum tillage of trashy land at shallow depths n. Dried hard soils o. Cutting and pulverisation in wet sticky clay soil p. For operating on the sides of plant bed

Description : Curved twisted blades are specially suited for m. Minimum tillage of trashy land at shallow depths n. Dried hard soils o. Cutting and pulverisation in wet sticky clay soil p. For operating on the sides of plant bed

Last Answer : p. For operating on the sides of plant bed

Differential lock offers advantage of E. Threshing efficiency of thresher (power operated) F. Capacity of chaff cutters G. Cleaning capacity of straw walkers H. None of the above

Description : Differential lock offers advantage of E. Threshing efficiency of thresher (power operated) F. Capacity of chaff cutters G. Cleaning capacity of straw walkers H. None of the above

Last Answer : F. Capacity of chaff cutters

Different parts of Thresher are A) Feeding device B) Threshing cylinder C) Concave D) All of the above.

Description : Different parts of Thresher are A) Feeding device B) Threshing cylinder C) Concave D) All of the above.

Last Answer : All of the above.

Increasing non grain feed rate increase (a) Cylinder losses (b) Seed damage (c) Both (a) and(b) (d) None of the above

Description : Increasing non grain feed rate increase (a) Cylinder losses (b) Seed damage (c) Both (a) and(b) (d) None of the above

Last Answer : (a) Cylinder losses

Increasing non-grain feed rate increase a) Cylinder losses b) seed damage c)Both (a) and (b) d) none of the above

Description : Increasing non-grain feed rate increase a) Cylinder losses b) seed damage c)Both (a) and (b) d) none of the above

Last Answer : a) Cylinder losses

.An olpad thresher is operated (A) Manually (B)By a pair of Bullocks (C)By a tractor (D)By an electric motor

Description : .An olpad thresher is operated (A) Manually (B)By a pair of Bullocks (C)By a tractor (D)By an electric motor

Last Answer : (B)By a pair of Bullocks

Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm

Description : Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm

Last Answer : c) 600-800rpm

Cleaning of sugarcane is obtained at peripheral speed A. 12-15m/sec B. 18-20m/sec C. 20-25m/sec D. 25-30m/sec

Description : Cleaning of sugarcane is obtained at peripheral speed A. 12-15m/sec B. 18-20m/sec C. 20-25m/sec D. 25-30m/sec

Last Answer : B. 18-20m/sec

The average spacing of seeds or hills in field is obtained or determined by a) The ratio of linear or peripheral speed of seed pick up units (cells fingers, etc) to the forward speed of the planter b) The distance between the speed pick up units (cells) on the metering unit c) Both (a) and (b) d) None of the above

Description : The average spacing of seeds or hills in field is obtained or determined by a) The ratio of linear or peripheral speed of seed pick up units (cells fingers, etc) to the forward speed of the planter b) The distance ... up units (cells) on the metering unit c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

Needle bearing a roller bearing having a number of smaller diameter roller is well suited to a) Application involving oscillating motion b) Exceptionally high load capacity application at low peripheral speed c) Both (a) and (b) d) None of the above

Description : Needle bearing a roller bearing having a number of smaller diameter roller is well suited to a) Application involving oscillating motion b) Exceptionally high load capacity application at low peripheral speed c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

The ratio of reel peripheral speed to forward speed of combine is called (a)velocity index (b)angular velocity index (c)reel speed index (d) kinematic index

Description : The ratio of reel peripheral speed to forward speed of combine is called (a)velocity index (b)angular velocity index (c)reel speed index (d) kinematic index

Last Answer : (c)reel speed index

onstant speed governors are used on ∙ Tractor engine diesel ∙ Stationary diesel engine ∙ Petrol engine ∙ None of the above

Description : onstant speed governors are used on ∙ Tractor engine diesel ∙ Stationary diesel engine ∙ Petrol engine ∙ None of the above

Last Answer : Stationary diesel engine

variable speed governors are used on ∙ Tractor engine(diesel) ∙ Stationary engine (diesel) ∙ Petrol engine ∙ None of the above

Description : variable speed governors are used on ∙ Tractor engine(diesel) ∙ Stationary engine (diesel) ∙ Petrol engine ∙ None of the above

Last Answer : ∙ Tractor engine(diesel)

349- Pods, heads or ears & freeseeds, lost during the cutting & conveying operation are called as..... (a) Cylinder loss (b) Walker losses ( rack loss) (c) Shoe losses (d) Gathering loss

Description : 349- Pods, heads or ears & freeseeds, lost during the cutting & conveying operation are called as..... (a) Cylinder loss (b) Walker losses ( rack loss) (c) Shoe losses (d) Gathering loss

Last Answer : (d) Gathering loss

Free (threshed) seed carried over the straw discharged from the rear shoe is called as (a) Cylinder loss (b)walker loss (rack Loss) (b) Shoe loss (d) gathering loss

Description : Free (threshed) seed carried over the straw discharged from the rear shoe is called as (a) Cylinder loss (b)walker loss (rack Loss) (b) Shoe loss (d) gathering loss

Last Answer : (b) Shoe loss

Free (threshed) seed carried over the walker or rack in straw and discharge from the rear of machine is called as (a) Cylinder loss (b) walker loss(rack loss) (c) Shoe loss (d) gathering loss

Description : Free (threshed) seed carried over the walker or rack in straw and discharge from the rear of machine is called as (a) Cylinder loss (b) walker loss(rack loss) (c) Shoe loss (d) gathering loss

Last Answer : (b) walker loss(rack loss)

Unthreshed seed discharged from the rear of the machine either in straw or in the material from the cleaning shoe is called (a)cylinder loss (b)walker loss (rack loss) (c)shoe loss (d) gathering loss

Description : Unthreshed seed discharged from the rear of the machine either in straw or in the material from the cleaning shoe is called (a)cylinder loss (b)walker loss (rack loss) (c)shoe loss (d) gathering loss

Last Answer : (a)cylinder loss

A power tiller is most suited for : A. Draft operation with rigid tools B. Rotary cultivation C. Stationary operation D. Transport work

Description : A power tiller is most suited for : A. Draft operation with rigid tools B. Rotary cultivation C. Stationary operation D. Transport work

Last Answer : B. Rotary cultivation

iesel engine has less reserve torque then spark ignition because ∙ Torque-speed curve is governed by volumetric efficiency of fuel pump and engine cylinder ∙ Torque is a function of thermal efficiency ∙ Diesel engine has generally low speed engine ∙ None of the above

Description : iesel engine has less reserve torque then spark ignition because ∙ Torque-speed curve is governed by volumetric efficiency of fuel pump and engine cylinder ∙ Torque is a function of thermal efficiency ∙ Diesel engine has generally low speed engine ∙ None of the above

Last Answer : ∙ Torque is a function of thermal efficiency

The two types of cylinder used on power wheat threshers are: a) Serrated disc and rasp bar b) Spike tooth and wire loop type c) Spike tooth and hammer mill d) Hammer mill and flails

Description : The two types of cylinder used on power wheat threshers are: a) Serrated disc and rasp bar b) Spike tooth and wire loop type c) Spike tooth and hammer mill d) Hammer mill and flails

Last Answer : c) Spike tooth and hammer mill

Firing order of a six cylinder engine in which no two adjacent cylinder have power stroke is (a) 1 5 3 6 2 4 (b) 1 2 3 4 5 6 (c) 1 5 4 6 3 2 (d) 1 4 2 5 6 3

Description : Firing order of a six cylinder engine in which no two adjacent cylinder have power stroke is (a) 1 5 3 6 2 4 (b) 1 2 3 4 5 6 (c) 1 5 4 6 3 2 (d) 1 4 2 5 6 3

Last Answer : (a) 1 5 3 6 2 4

hen displacement volume is divided by piston displacement, what will we obtained (a) number of cylinders (b) number of power stroke per minute for all cylinders (c) number of revolution of the crankshaft (engine) (d) number of revolution of crankshaft × number of cylinder

Description : hen displacement volume is divided by piston displacement, what will we obtained (a) number of cylinders (b) number of power stroke per minute for all cylinders (c) number of revolution of the crankshaft (engine) (d) number of revolution of crankshaft × number of cylinder

Last Answer : (b) number of power stroke per minute for all cylinders

The mechanical cleaning of sugar cane is done due to A. The different in the peripheral velocity of rollers B. Rough surface provided Or the outer surface of rollers C. Blow of air which forces the extraneous material out of the machine D. All of the above

Description : The mechanical cleaning of sugar cane is done due to A. The different in the peripheral velocity of rollers B. Rough surface provided Or the outer surface of rollers C. Blow of air which forces the extraneous material out of the machine D. All of the above

Last Answer : D. All of the above

_______ designates the shape of gross peripheral and cross-sectional boundaries of the soil working tool a) Micro shape c) Edge shape b) Macro shape d) Gross shape

Description : _______ designates the shape of gross peripheral and cross-sectional boundaries of the soil working tool a) Micro shape c) Edge shape b) Macro shape d) Gross shape

Last Answer : c) Edge shape

The metering mechanism which is suitable for the metering of small seeds as well as large grains. (a) Internal double run mechanism (b) Fluted wheel mechanism (c) Stationary opening with auger (d) None of the above

Description : The metering mechanism which is suitable for the metering of small seeds as well as large grains. (a) Internal double run mechanism (b) Fluted wheel mechanism (c) Stationary opening with auger (d) None of the above

Last Answer : (a) Internal double run mechanism

Most commonly used metering device for bulk flow seed metering of small and medium size seeds (grains) a) Fluted wheel b) Internal double run c) Stationary opening with agitator d) None of the above

Description : Most commonly used metering device for bulk flow seed metering of small and medium size seeds (grains) a) Fluted wheel b) Internal double run c) Stationary opening with agitator d) None of the above

Last Answer : a) Fluted wheel

Which end of the disc harrow penetrates deeply a) Concave b) Convex c) Rear d) Front

Description : Which end of the disc harrow penetrates deeply a) Concave b) Convex c) Rear d) Front

Last Answer : a) Concave

Which end of disc harrow tends to penetrate more deeply a) Concave b) Convex c) Rear d) Front

Description : Which end of disc harrow tends to penetrate more deeply a) Concave b) Convex c) Rear d) Front

Last Answer : a) Concave

Blades of disc harrow are sharpened from the_______ side penetrate more readily than blades sharpened from the__________ side a) convex, concave c) concave, convex b) Front, rear d) Rear, front

Description : Blades of disc harrow are sharpened from the_______ side penetrate more readily than blades sharpened from the__________ side a) convex, concave c) concave, convex b) Front, rear d) Rear, front

Last Answer : c) concave, convex

Crop factors which affecting thresher preformation. a) Variety of crop, Moisture in crop material b) Feeding chute angle, cylinder types c) Cylinder speed, feed rate d) Cylinder type, feed rate

Description : Crop factors which affecting thresher preformation. a) Variety of crop, Moisture in crop material b) Feeding chute angle, cylinder types c) Cylinder speed, feed rate d) Cylinder type, feed rate

Last Answer : Variety of crop, Moisture in crop material

Operational factors which affecting thresher preformation. a) Variety of crop, Moisture in crop material b) Feeding chute angle, cylinder type c) Cylinder speed, feed rate d) Cylinder type ,feed rate

Description : Operational factors which affecting thresher preformation. a) Variety of crop, Moisture in crop material b) Feeding chute angle, cylinder type c) Cylinder speed, feed rate d) Cylinder type ,feed rate

Last Answer : Cylinder speed, feed rate