Tension on slack side in case of chain drive a) Lesser than on tight side b) Greater than on tight side c) Zero d) Equal to that on tight side

Tension on slack side in case of chain drive
a) Lesser than on tight side
b) Greater than on tight side
c) Zero
d) Equal to that on tight side
by

1 Answer

Answer :

c) Zero
by

Related questions

Tension on the slack side in chain drive is A)more than on tight side. B)less than on tight side. C)zero. D)equal to tight

Description : Tension on the slack side in chain drive is A)more than on tight side. B)less than on tight side. C)zero. D)equal to tight

Last Answer : C)zero

Spiral gear are used for transmitting power between two shaft Inclined at a. Right angle to each other and axes can intersect b. Right angle to each other and axes cannot intersect c. At angle slightly lesser or greater than 90 of axles can meet d. None of the above

Description : Spiral gear are used for transmitting power between two shaft Inclined at a. Right angle to each other and axes can intersect b. Right angle to each other and axes cannot intersect c. At angle slightly lesser or greater than 90 of axles can meet d. None of the above

Last Answer : c. At angle slightly lesser or greater than 90 of axles can meet

Belt Tension can be adjusted by a. idler pulley b. slide rails c. tilting plate drive d. all the above

Description : Belt Tension can be adjusted by a. idler pulley b. slide rails c. tilting plate drive d. all the above

Last Answer : d. all the above

Desired tension in an open belt drive system can be maintained (without changing center to center distance between two pulley)by using A)ldler pulley. B)slide rail C) Tilting angle. D)none of the above

Description : Desired tension in an open belt drive system can be maintained (without changing center to center distance between two pulley)by using A)ldler pulley. B)slide rail C) Tilting angle. D)none of the above

Last Answer : A)ldler pulley

Lewis formula is used in the design of a) gears b) clutch c) chain drive d) belt drives

Description : Lewis formula is used in the design of a) gears b) clutch c) chain drive d) belt drives

Last Answer : a) gears

Transplanter using soil bearing seedlings are more popular than washed root seedling transplanter because of a) less labour requirement b) lesser plant missing percentage c) higher work rates d) all of the above

Description : Transplanter using soil bearing seedlings are more popular than washed root seedling transplanter because of a) less labour requirement b) lesser plant missing percentage c) higher work rates d) all of the above

Last Answer : d) all of the above

At smaller disc angles , the draft tends to increase in disc plough because of a) Greater contact area between furrow wall and the convex side of the disc b) Increase in the side draft c) Greater throw of the soil d) All of the above

Description : At smaller disc angles , the draft tends to increase in disc plough because of a) Greater contact area between furrow wall and the convex side of the disc b) Increase in the side draft c) Greater throw of the soil d) All of the above

Last Answer : a) Greater contact area between furrow wall and the convex side of the disc

Differential lock offers advantage of A. Better drawbar pull when drive wheel are under different conditions B. Easier to plant in straight rows C. Reduces stearing effort and side draft when operating with certain implements D. All of the above

Description : Differential lock offers advantage of A. Better drawbar pull when drive wheel are under different conditions B. Easier to plant in straight rows C. Reduces stearing effort and side draft when operating with certain implements D. All of the above

Last Answer : D. All of the above

Function of idler pully are a. to increase the angle of contact of belt on pully b. maintain belt tension as belt stretches c. canter to centre distance remain same d. all the above

Description : Function of idler pully are a. to increase the angle of contact of belt on pully b. maintain belt tension as belt stretches c. canter to centre distance remain same d. all the above

Last Answer : d. all the above

Smaller tension ratio result in.... (a) Unnecessary high tension in belt (b) Reduction in belt life (c) Both (c) & (b) (d) Excessive belt slippage

Description : Smaller tension ratio result in.... (a) Unnecessary high tension in belt (b) Reduction in belt life (c) Both (c) & (b) (d) Excessive belt slippage

Last Answer : (c) Both (c) & (b)

310- Larger tension ratio result in... (a) Unnecessary high tension in belt (b) Reduction in belt life (c) Excessive belt slippage (d) Increase belt life

Description : 310- Larger tension ratio result in... (a) Unnecessary high tension in belt (b) Reduction in belt life (c) Excessive belt slippage (d) Increase belt life

Last Answer : (c) Excessive belt slippage

The formula for tension difference or effective pull, required to transmit the load at.... (a) (Tt-Ts)=1000(kw/V) (b) Tt/Ts=c^ke (c) (Tt-Ts)= 1000(Hp/V) (d) None of the above

Description : The formula for tension difference or effective pull, required to transmit the load at.... (a) (Tt-Ts)=1000(kw/V) (b) Tt/Ts=c^ke (c) (Tt-Ts)= 1000(Hp/V) (d) None of the above

Last Answer : (a) (Tt-Ts)=1000(kw/V)

When compared to ordinary Portland cement, Rapid hardening Portland cement contains ______________ amount of lime content [ A ] Equal [ B ] Greater [ C ] Lesser [ D ] Zero

Description : When compared to ordinary Portland cement, Rapid hardening Portland cement contains ______________ amount of lime content [ A ] Equal [ B ] Greater [ C ] Lesser [ D ] Zero

Last Answer : [ B ] Greater

Chain drives are stable for a) Constant speed ratio between parallel shafts b) Distance between centre to centre is moderate c) Dirty and dusty environment d) All of the above

Description : Chain drives are stable for a) Constant speed ratio between parallel shafts b) Distance between centre to centre is moderate c) Dirty and dusty environment d) All of the above

Last Answer : d) All of the above

In an offset disc harrow the angle between two gang is a) less than 90 degree b) 90 degree c) greater than 90 degree d) 180degree

Description : In an offset disc harrow the angle between two gang is a) less than 90 degree b) 90 degree c) greater than 90 degree d) 180degree

Last Answer : a) less than 90 degre

ln single action disc harrow the two gangs are at set single a) less than 90 degree b) at 90 degree c) greater than 90 degree d) at 180 degree

Description : n single action disc harrow the two gangs are at set single a) less than 90 degree b) at 90 degree c) greater than 90 degree d) at 180 degree

Last Answer : c) greater than 90 degree

In a horizontal plate type planter maximum obtainable value of cell fill is : A.Greater then 100% B.Less than 100% C.200% D.None of the above

Description : In a horizontal plate type planter maximum obtainable value of cell fill is : A.Greater then 100% B.Less than 100% C.200% D.None of the above

Last Answer : A.Greater then 100%

When frequency of occurrence of overload is less and magnitude of overload is also less than safety device used is a) Safety jump clutch b) Shear device c) Frictional device d) V-belt drive

Description : When frequency of occurrence of overload is less and magnitude of overload is also less than safety device used is a) Safety jump clutch b) Shear device c) Frictional device d) V-belt drive

Last Answer : a) Safety jump clutch

When frequency of occurrence of overload is less but the mangnitude of overload is large than safety device used is: a) Safety jump clutch b) Shear device c) Frictional device d) V-belt drive

Description : When frequency of occurrence of overload is less but the mangnitude of overload is large than safety device used is: a) Safety jump clutch b) Shear device c) Frictional device d) V-belt drive

Last Answer : b) Shear device

A relative short and broad mould board is curved rather abruptly near the top resulting in a greater degree of pulverization is called a. Sod bottom b. Stubble bottom b. General bottom d. Slat bottom

Description : A relative short and broad mould board is curved rather abruptly near the top resulting in a greater degree of pulverization is called a. Sod bottom b. Stubble bottom b. General bottom d. Slat bottom

Last Answer : b. General bottom

The method which depreciates the tractor or machine to zero at the end of its expected life is known as: A. Estimated value B. Sum-of-the digits C. Declining balance D. Straight line

Description : The method which depreciates the tractor or machine to zero at the end of its expected life is known as: A. Estimated value B. Sum-of-the digits C. Declining balance D. Straight line

Last Answer : D. Straight line

Hook link chains are a)suitable for external drive exposed atmosphere b)made of meabble iron c)used where power requirement is low and speed is low d)All of the above

Description : Hook link chains are a)suitable for external drive exposed atmosphere b)made of meabble iron c)used where power requirement is low and speed is low d)All of the above

Last Answer : d)All of the above

When V-belt drive is used a safety device, its performance is affected by a) Variation in belt tention b) Increase in coefficient of friction as belt slippage increase c) Both (a) and (b) d) None of the above

Description : When V-belt drive is used a safety device, its performance is affected by a) Variation in belt tention b) Increase in coefficient of friction as belt slippage increase c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

In comparison to jump clutchs, advantages of the friction safety clutches is/are a) More consistent break away torque b) No damageing peak during slippage c) Protecting a drive from high freuency peak torque (2-3 time normal values) d) All of the above

Description : In comparison to jump clutchs, advantages of the friction safety clutches is/are a) More consistent break away torque b) No damageing peak during slippage c) Protecting a drive from high freuency peak torque (2-3 time normal values) d) All of the above

Last Answer : d) All of the above

rank speed on the mower with conventional pit man drive is a)850-1000 rpm b)1000-1200rpm c)800-1150rpm d)1200-1600 rpm

Description : rank speed on the mower with conventional pit man drive is a)850-1000 rpm b)1000-1200rpm c)800-1150rpm d)1200-1600 rpm

Last Answer : a)850-1000 rpm

V-belt drive transmission system is used when it is designed to achieve a) High speed ratio b) Space requirements are limited c) Both (a) and (b) d) None of the above

Description : V-belt drive transmission system is used when it is designed to achieve a) High speed ratio b) Space requirements are limited c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

Swinging drawbar is advantageous because it help A. Taking short turn with machine wider than the tractor B. Reduces side draft C. Leaves only small area uncovered at corner of the fied D. All the above

Description : Swinging drawbar is advantageous because it help A. Taking short turn with machine wider than the tractor B. Reduces side draft C. Leaves only small area uncovered at corner of the fied D. All the above

Last Answer : A. Taking short turn with machine wider than the tractor

Blades of disc harrow are sharpened from the_______ side penetrate more readily than blades sharpened from the__________ side a) convex, concave c) concave, convex b) Front, rear d) Rear, front

Description : Blades of disc harrow are sharpened from the_______ side penetrate more readily than blades sharpened from the__________ side a) convex, concave c) concave, convex b) Front, rear d) Rear, front

Last Answer : c) concave, convex

The temperature at which fuel flows to case is called.... (a) Fire point (b) Flash point (c) Pour point (d) Cloud point

Description : The temperature at which fuel flows to case is called.... (a) Fire point (b) Flash point (c) Pour point (d) Cloud point

Last Answer : c) Pour point

Speed of the cutter bar in case of combine (grain) is (a)400-550 rpm (b) 500-800rpm (c)800-1000rpm (d) 1000-1200rpm

Description : Speed of the cutter bar in case of combine (grain) is (a)400-550 rpm (b) 500-800rpm (c)800-1000rpm (d) 1000-1200rpm

Last Answer : a)400-550 rpm

.When the valves are carried in engine bioel at one side of each cylinder is called A. Valves in head arrangements B. L-head C. I-head D. None of the above

Description : .When the valves are carried in engine bioel at one side of each cylinder is called A. Valves in head arrangements B. L-head C. I-head D. None of the above

Last Answer : B. L-head

.The land side of a mould board plough is made of: A. Malleable iron B. Forged steel C. C45 steel D. Soft Centre steel

Description : .The land side of a mould board plough is made of: A. Malleable iron B. Forged steel C. C45 steel D. Soft Centre steel

Last Answer : D. Soft Centre steel

An engine is called I or valve in head engine when a) Valve are immediately above the cylinder b) Both valves are on one side c) Both valves are on opposite direction d) None of the above

Description : An engine is called I or valve in head engine when a) Valve are immediately above the cylinder b) Both valves are on one side c) Both valves are on opposite direction d) None of the above

Last Answer : d) None of the above

Dead furrow open furrow is called when plowing is done by (a) Center to side (b) side to center method (c) one way plowing (d) none of the above

Description : Dead furrow open furrow is called when plowing is done by (a) Center to side (b) side to center method (c) one way plowing (d) none of the above

Last Answer : (b) side to center method

Back furrow is caused while plowing is done (a)center to side (b) side to center (c)one way plowing. (c) none of the above

Description : Back furrow is caused while plowing is done (a)center to side (b) side to center (c)one way plowing. (c) none of the above

Last Answer : a)center to side

Total force exerted upon the implement by a power unit called a)pull. B) draft C)side draft. D)unit draft

Description : Total force exerted upon the implement by a power unit called a)pull. B) draft C)side draft. D)unit draft

Last Answer : a)pull

Horizontal component of pull perpendicular to the line of motion is called: A.Draft B.Side draft C.Transerve component D. Pull

Description : Horizontal component of pull perpendicular to the line of motion is called: A.Draft B.Side draft C.Transerve component D. Pull

Last Answer : B.Side draft

knives of the cutter bar are scrratedin order to a)Increase the co-efficient of friction between crop stalk machine b)Reducing the deflection of stalk side ways c)To increase the cutting speed d)To improve cutting height

Description : knives of the cutter bar are scrratedin order to a)Increase the co-efficient of friction between crop stalk machine b)Reducing the deflection of stalk side ways c)To increase the cutting speed d)To improve cutting height

Last Answer : a)Increase the co-efficient of friction between crop stalk machine

346- Side deflection of stalk can be minimized by.... (a) Having a short cutting stroke (b) Having an arrangement to obtain two cuts per stroke (c) Both (a) & (b) (d) None of the above

Description : 346- Side deflection of stalk can be minimized by.... (a) Having a short cutting stroke (b) Having an arrangement to obtain two cuts per stroke (c) Both (a) & (b) (d) None of the above

Last Answer : (c) Both (a) & (b)

The maximum of spacing of side face reinforcement shall not exceed [ A ] 300 mm [ B ] Web thickness [ C ] Lesser of (a) and (b) [ D ] Greater of (a) and (b)

Description : The maximum of spacing of side face reinforcement shall not exceed [ A ] 300 mm [ B ] Web thickness [ C ] Lesser of (a) and (b) [ D ] Greater of (a) and (b)

Last Answer : [ C ] Lesser of (a) and (b)

Average pull developed by a pair of bullocks (a) 1/10 of their body weight (b) Equal to bosey weight (c) 1/2 of their body weight (d) None of the above

Description : Average pull developed by a pair of bullocks (a) 1/10 of their body weight (b) Equal to bosey weight (c) 1/2 of their body weight (d) None of the above

Last Answer : (a) 1/10 of their body weight

owest specific energy requirement for the operation of rotavator is about _______ times as great as a mould board plough working in the same soil. a) Equal b) Twice c) Three d) Four

Description : owest specific energy requirement for the operation of rotavator is about _______ times as great as a mould board plough working in the same soil. a) Equal b) Twice c) Three d) Four

Last Answer : c) Three

.Increase the grain/non grain ratio on the shoe tends to the shoe losses (a) Decreases (b) Increases (c) Decrease or increase (d) Equal

Description : .Increase the grain/non grain ratio on the shoe tends to the shoe losses (a) Decreases (b) Increases (c) Decrease or increase (d) Equal

Last Answer : (d) Equal

.Incresase amount of the non grain material on the straw Walker the walker (a) Decrease (b) Increase (c) Unaffected (d) Equal

Description : .Incresase amount of the non grain material on the straw Walker the walker (a) Decrease (b) Increase (c) Unaffected (d) Equal

Last Answer : b) Increase

Center of resistence of a mould board plow less at distance equal to A. 1/4th the size of plow from the share wing B. 3/4th the size of plow from the share wing C. 2/3th the size of plow from the share wing D. 1/3th the size of plow from the share wing

Description : Center of resistence of a mould board plow less at distance equal to A. 1/4th the size of plow from the share wing B. 3/4th the size of plow from the share wing C. 2/3th the size of plow from the share wing D. 1/3th the size of plow from the share wing

Last Answer : B. 3/4th the size of plow from the share wing

Increasing the grain/non-grain ratio on shoe tends to _________ the shoe losses a) Decrease b) Increase c)Decrease or increase d) Equal

Description : Increasing the grain/non-grain ratio on shoe tends to _________ the shoe losses a) Decrease b) Increase c)Decrease or increase d) Equal

Last Answer : c)Decreas

Increase amount of non-grain material on the straw walker _______ the walker losses a) Decreases b) Increases c) Unaffected d) Equal

Description : Increase amount of non-grain material on the straw walker _______ the walker losses a) Decreases b) Increases c) Unaffected d) Equal

Last Answer : b) Increase

Torricelli's theorem states that the velocity ‘v’ of the liquid emerging from the bottom of the wide tank is given by √(2gh). In practice, this velocity is: A. equal to √(2gh) B. greater than √(2gh) C. lesser than √(2ghD. independent of height and gravitational field strength)

Description : Torricelli's theorem states that the velocity ‘v’ of the liquid emerging from the bottom of the wide tank is given by √(2gh). In practice, this velocity is: A. equal to √(2gh) B. greater than √(2gh) C. lesser than √(2gh) D. independent of height and gravitational field strength

Last Answer :  lesser than √(2gh

Temperature rise in partial bearing is ____ than full bearing. a) Lesser b) Greater c) Equal

Description : Temperature rise in partial bearing is ____ than full bearing. a) Lesser b) Greater c) Equal

Last Answer : a) Lesser

Coarse threads have helix angle _____ fine threads. a) Equal to b) Greater than c) Lesser than d) There is no relation

Description : Coarse threads have helix angle _____ fine threads. a) Equal to b) Greater than c) Lesser than d) There is no relation

Last Answer : c) Lesser than