Axial flow thresher utilises (a) Rasp bar cylinder (b) Spike tooth cylinder (c) Hammer mill cylinder (d) Peg tooth cylinder

Axial flow thresher utilises  
  
(a) Rasp bar cylinder
(b) Spike tooth cylinder  
(c) Hammer mill cylinder  
(d) Peg tooth cylinder
by

1 Answer

Answer :

(b) Spike tooth cylinder
by

Related questions

Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type c) Spike tooth d) Hammer mill

Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type c) Spike tooth d) Hammer mill

Last Answer : a) Raspbar type cylinder

Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type cylinder c) Spike tooth d) Hammer mill

Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type cylinder c) Spike tooth d) Hammer mill

Last Answer : a) Raspbar type cylinder

The two types of cylinder used on power wheat threshers are: a) Serrated disc and rasp bar b) Spike tooth and wire loop type c) Spike tooth and hammer mill d) Hammer mill and flails

Description : The two types of cylinder used on power wheat threshers are: a) Serrated disc and rasp bar b) Spike tooth and wire loop type c) Spike tooth and hammer mill d) Hammer mill and flails

Last Answer : c) Spike tooth and hammer mill

A multi type thresher is equipped with a) Spike tooth cylinder b) Rasp bar cylinder c) Hammer mill cylinder d) All of the above

Description : A multi type thresher is equipped with a) Spike tooth cylinder b) Rasp bar cylinder c) Hammer mill cylinder d) All of the above

Last Answer : All of the above

The dummy type thresher is also termed as a) Rasp bar type thresher b) Hammer mill type thresher c) Spike tooth type thresher d) Syndicator tooth type thresher

Description : The dummy type thresher is also termed as a) Rasp bar type thresher b) Hammer mill type thresher c) Spike tooth type thresher d) Syndicator tooth type thresher

Last Answer : Hammer mill type thresher

The two types of cylinders used on power wheat threshers are 1. Serrated disc and rasp bar 2. Spike tooth and wire loop type 3. Spike tooth and hammer mill 4. hammer mill and flails

Description : The two types of cylinders used on power wheat threshers are 1. Serrated disc and rasp bar 2. Spike tooth and wire loop type 3. Spike tooth and hammer mill 4. hammer mill and flails

Last Answer : ans 3

This type thresher consists of beater mounted on a shaft which rotates inside a closed casing and concave. a. Hammer mill b. Spike tooth d. None of above

Description : This type thresher consists of beater mounted on a shaft which rotates inside a closed casing and concave. a. Hammer mill b. Spike tooth d. None of above

Last Answer : Ans-                             c. Dummy

This type threasher consist of spike tooth cylinder, woven wire mesh concave and upper casing provide with helical louvers. a. Hammer mill c. Dummy d. None of above

Description : This type threasher consist of spike tooth cylinder, woven wire mesh concave and upper casing provide with helical louvers. a. Hammer mill c. Dummy d. None of above

Last Answer : Ans-    b. Axial flow

Identify the picture. a) Hummer mill type b) Spike-tooth type c) Dummy type d) Axial flow type

Description : Identify the picture. a) Hummer mill type b) Spike-tooth type c) Dummy type d) Axial flow type

Last Answer : Hummer mill type

are mounted on the Periphery of a cylinder that rotates inside a closed casing and concave. a) Dummy type c) spike-tooth type b) Hummer type d) Axial flow type

Description : are mounted on the Periphery of a cylinder that rotates inside a closed casing and concave. a) Dummy type c) spike-tooth type b) Hummer type d) Axial flow type

Last Answer : spike-tooth type

t consists of spike tooth cylinder, woven- wire mesh concave and upper casing provided with helical concave. a) Dummy type c) Spike-tooth type b) Hummer type d) Axial flow type

Description : It consists of spike tooth cylinder, woven- wire mesh concave and upper casing provided with helical concave. a) Dummy type c) Spike-tooth type b) Hummer type d) Axial flow type

Last Answer : Axial flow type

This type thresher consists of corrugated bars are mounted axially on pheripheri of the cylinder. a. Hammer mill c. Dummy d. None of above

Description : This type thresher consists of corrugated bars are mounted axially on pheripheri of the cylinder. a. Hammer mill c. Dummy d. None of above

Last Answer : Ans-    b. Raspbar

Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Description : Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Last Answer : d) 1100-1200rpm

Adjustment needed when thresher blows grains with chaff a.) Decreasing cylinder peripheral speed. b.) Increasing cylinder speed. c.) Decreasing feed rate. d.) Increasing cylinder

Description : Adjustment needed when thresher blows grains with chaff a.) Decreasing cylinder peripheral speed. b.) Increasing cylinder speed. c.) Decreasing feed rate. d.) Increasing cylinder

Last Answer : a.) Decreasing cylinder peripheral speed.

Thresher blows broken grains with chaff due to a) Higher cylinder speed. b) More feed Rate c) More cylinder concave clearance d) Moisture content of the crop is more

Description : Thresher blows broken grains with chaff due to a) Higher cylinder speed. b) More feed Rate c) More cylinder concave clearance d) Moisture content of the crop is more

Last Answer : a) Higher cylinder speed.

Cylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peripheral speed N. Concave clearance O. Blower speed P. All of the above

Description : Cylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peCylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peripheral speed N. Concave clearance O. Blower speed P. All of the above

Last Answer : M. Cylinder peripheral speed

it is a harrow with peg shaped teeth of diamond cross section to a Rectangular frame. A) Spike tooth harrow C Spring tooth harrow B) Acme harrow D Triangular harrow.

Description : it is a harrow with peg shaped teeth of diamond cross section to a Rectangular frame. A) Spike tooth harrow C Spring tooth harrow B) Acme harrow D Triangular harrow.

Last Answer : Spike tooth harrow

It consists of beats mounted on a shaft which rotates inside a closed casing and concave. a) Dummy type c) Spike-tooth type c) Hummer type d) Axial flow type

Description : It consists of beats mounted on a shaft which rotates inside a closed casing and concave. a) Dummy type c) Spike-tooth type c) Hummer type d) Axial flow type

Last Answer : Dummy type

Optimum speed for grains like gram,pea,etc.,thresher using power is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Description : Optimum speed for grains like gram,pea,etc.,thresher using power is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Last Answer : a) 300-400rpm

.An olpad thresher is operated (A) Manually (B)By a pair of Bullocks (C)By a tractor (D)By an electric motor

Description : .An olpad thresher is operated (A) Manually (B)By a pair of Bullocks (C)By a tractor (D)By an electric motor

Last Answer : (B)By a pair of Bullocks

Differential lock offers advantage of E. Threshing efficiency of thresher (power operated) F. Capacity of chaff cutters G. Cleaning capacity of straw walkers H. None of the above

Description : Differential lock offers advantage of E. Threshing efficiency of thresher (power operated) F. Capacity of chaff cutters G. Cleaning capacity of straw walkers H. None of the above

Last Answer : F. Capacity of chaff cutters

In threshers what are mounted on the periphery of the cylinder A) Spike tooth type B) Raspbar type C) Syndicator type D) Wire loob type.

Description : In threshers what are mounted on the periphery of the cylinder A) Spike tooth type B) Raspbar type C) Syndicator type D) Wire loob type.

Last Answer : Spike tooth type

This type thresher consists of a flywheel with corrugation on its periphery and sides. Rims of flywheel fitted with chopping blades. b. Axial flow c. Dummy d. None of above

Description : This type thresher consists of a flywheel with corrugation on its periphery and sides. Rims of flywheel fitted with chopping blades. b. Axial flow c. Dummy d. None of above

Last Answer : Ans-    a. Syndicator

In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.

Description : In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.

Last Answer : 1200 to 1500

Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm

Description : Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm

Last Answer : c) 600-800rpm

.When the valves are carried in engine bioel at one side of each cylinder is called A. Valves in head arrangements B. L-head C. I-head D. None of the above

Description : .When the valves are carried in engine bioel at one side of each cylinder is called A. Valves in head arrangements B. L-head C. I-head D. None of the above

Last Answer : B. L-head

An engine is called I or valve in head engine when a) Valve are immediately above the cylinder b) Both valves are on one side c) Both valves are on opposite direction d) None of the above

Description : An engine is called I or valve in head engine when a) Valve are immediately above the cylinder b) Both valves are on one side c) Both valves are on opposite direction d) None of the above

Last Answer : d) None of the above

Most important factor affecting threshing efficiency a)peripheral speed of the drum b)cylinder concave clearance c)moisture content of crop d)feed rate

Description : Most important factor affecting threshing efficiency a)peripheral speed of the drum b)cylinder concave clearance c)moisture content of crop d)feed rate

Last Answer : a)peripheral speed of the drum

A threshing cylinder of 15cm radius is rotating at 700rpm if peripheral velocity (m/sec) will be a. 11 b.105 c. 210 d. 660

Description : A threshing cylinder of 15cm radius is rotating at 700rpm if peripheral velocity (m/sec) will be a. 11 b.105 c. 210 d. 660

Last Answer : a. 11

Increasing non grain feed rate increase (a) Cylinder losses (b) Seed damage (c) Both (a) and(b) (d) None of the above

Description : Increasing non grain feed rate increase (a) Cylinder losses (b) Seed damage (c) Both (a) and(b) (d) None of the above

Last Answer : (a) Cylinder losses

Increasing the cylinder speed result in (a) Increase threshing efficiency (b) Reduce cylinder loss (c) Increase seed damage (d) All of the above

Description : Increasing the cylinder speed result in (a) Increase threshing efficiency (b) Reduce cylinder loss (c) Increase seed damage (d) All of the above

Last Answer : (a) Increase threshing efficiency

iesel engine has less reserve torque then spark ignition because ∙ Torque-speed curve is governed by volumetric efficiency of fuel pump and engine cylinder ∙ Torque is a function of thermal efficiency ∙ Diesel engine has generally low speed engine ∙ None of the above

Description : iesel engine has less reserve torque then spark ignition because ∙ Torque-speed curve is governed by volumetric efficiency of fuel pump and engine cylinder ∙ Torque is a function of thermal efficiency ∙ Diesel engine has generally low speed engine ∙ None of the above

Last Answer : ∙ Torque is a function of thermal efficiency

Compression pressure in petrol engine cylinder is a) 6-10 kg/cm2 b) 10-20 kg/cm2 c) 20-35 kg/cm2 d) 35-40 kg/cm2

Description : Compression pressure in petrol engine cylinder is a) 6-10 kg/cm2 b) 10-20 kg/cm2 c) 20-35 kg/cm2 d) 35-40 kg/cm2

Last Answer : a) 6-10 kg/cm2

Compression pressure in diesel engine cylinder is a) 6-10 kg/cm2 b) 10-20 kg/cm2 c) 20-35 kg/cm2 d) None of the above

Description : Compression pressure in diesel engine cylinder is a) 6-10 kg/cm2 b) 10-20 kg/cm2 c) 20-35 kg/cm2 d) None of the above

Last Answer : c) 20-35 kg/cm2

Firing order of a six cylinder engine in which no two adjacent cylinder have power stroke is (a) 1 5 3 6 2 4 (b) 1 2 3 4 5 6 (c) 1 5 4 6 3 2 (d) 1 4 2 5 6 3

Description : Firing order of a six cylinder engine in which no two adjacent cylinder have power stroke is (a) 1 5 3 6 2 4 (b) 1 2 3 4 5 6 (c) 1 5 4 6 3 2 (d) 1 4 2 5 6 3

Last Answer : (a) 1 5 3 6 2 4

hen displacement volume is divided by piston displacement, what will we obtained (a) number of cylinders (b) number of power stroke per minute for all cylinders (c) number of revolution of the crankshaft (engine) (d) number of revolution of crankshaft × number of cylinder

Description : hen displacement volume is divided by piston displacement, what will we obtained (a) number of cylinders (b) number of power stroke per minute for all cylinders (c) number of revolution of the crankshaft (engine) (d) number of revolution of crankshaft × number of cylinder

Last Answer : (b) number of power stroke per minute for all cylinders

349- Pods, heads or ears & freeseeds, lost during the cutting & conveying operation are called as..... (a) Cylinder loss (b) Walker losses ( rack loss) (c) Shoe losses (d) Gathering loss

Description : 349- Pods, heads or ears & freeseeds, lost during the cutting & conveying operation are called as..... (a) Cylinder loss (b) Walker losses ( rack loss) (c) Shoe losses (d) Gathering loss

Last Answer : (d) Gathering loss

Increasing non-grain feed rate increase a) Cylinder losses b) seed damage c)Both (a) and (b) d) none of the above

Description : Increasing non-grain feed rate increase a) Cylinder losses b) seed damage c)Both (a) and (b) d) none of the above

Last Answer : a) Cylinder losses

Increasing the cylinder speed result in a) Increase threshing efficiency b) Reduce cylinder loss c) Increase seed damage d) All of the above

Description : Increasing the cylinder speed result in a) Increase threshing efficiency b) Reduce cylinder loss c) Increase seed damage d) All of the above

Last Answer : d) All of the above

Free (threshed) seed carried over the straw discharged from the rear shoe is called as (a) Cylinder loss (b)walker loss (rack Loss) (b) Shoe loss (d) gathering loss

Description : Free (threshed) seed carried over the straw discharged from the rear shoe is called as (a) Cylinder loss (b)walker loss (rack Loss) (b) Shoe loss (d) gathering loss

Last Answer : (b) Shoe loss

Free (threshed) seed carried over the walker or rack in straw and discharge from the rear of machine is called as (a) Cylinder loss (b) walker loss(rack loss) (c) Shoe loss (d) gathering loss

Description : Free (threshed) seed carried over the walker or rack in straw and discharge from the rear of machine is called as (a) Cylinder loss (b) walker loss(rack loss) (c) Shoe loss (d) gathering loss

Last Answer : (b) walker loss(rack loss)

Unthreshed seed discharged from the rear of the machine either in straw or in the material from the cleaning shoe is called (a)cylinder loss (b)walker loss (rack loss) (c)shoe loss (d) gathering loss

Description : Unthreshed seed discharged from the rear of the machine either in straw or in the material from the cleaning shoe is called (a)cylinder loss (b)walker loss (rack loss) (c)shoe loss (d) gathering loss

Last Answer : (a)cylinder loss

The two types of cylinders used on power wheat threshers are 1. Serrated disc and rasp bar 2.gears and belt pulleys 3. belt pulleys and chains 4 none of the above

Description : The two types of cylinders used on power wheat threshers are 1. Serrated disc and rasp bar 2.gears and belt pulleys 3. belt pulleys and chains 4 none of the above

Last Answer : ans 2

The cutter bar of a tractor operated mower ordinarily makes: A. Near the front axis B. 40mm towards the real axis C. At the power take off shaft D. Between the two lower Links

Description : The cutter bar of a tractor operated mower ordinarily makes: A. Near the front axis B. 40mm towards the real axis C. At the power take off shaft D. Between the two lower Links

Last Answer : D. Between the two lower Links

Which one of the below is a multipurpose tool a) Indigenous plough b) Cultivator c) Multipurpose tool bar carrier d) M.B plough

Description : Which one of the below is a multipurpose tool a) Indigenous plough b) Cultivator c) Multipurpose tool bar carrier d) M.B plough

Last Answer : c) Multipurpose tool bar carrier

The cutter bar of a tractor operated mower ordinarily makes: A. 800-1200 strokes/min B. 1600-2000 strokes/min C. 2400-2800 strokes/min D. 3200-3600 strokes/min

Description : The cutter bar of a tractor operated mower ordinarily makes: A. 800-1200 strokes/min B. 1600-2000 strokes/min C. 2400-2800 strokes/min D. 3200-3600 strokes/min

Last Answer : A. 800-1200 strokes/min

knives of the cutter bar are scrratedin order to a)Increase the co-efficient of friction between crop stalk machine b)Reducing the deflection of stalk side ways c)To increase the cutting speed d)To improve cutting height

Description : knives of the cutter bar are scrratedin order to a)Increase the co-efficient of friction between crop stalk machine b)Reducing the deflection of stalk side ways c)To increase the cutting speed d)To improve cutting height

Last Answer : a)Increase the co-efficient of friction between crop stalk machine

o over come the rear ward deflection the load given to outer end of the cutter bar is about..... (a)1.57cm/m (b) 2.0cm/m (b)3.0cm/m (d) 3.5cm/m

Description : o over come the rear ward deflection the load given to outer end of the cutter bar is about..... (a)1.57cm/m (b) 2.0cm/m (b)3.0cm/m (d) 3.5cm/m

Last Answer : b) 2.0cm/m

enght of cutter bar for the tractor operated mower or vertical conveyor reaper is..... (a) 1.5-3.0m (b) 3.0-4.5m (c)4.5-5.5m (d) >5.5m

Description : enght of cutter bar for the tractor operated mower or vertical conveyor reaper is..... (a) 1.5-3.0m (b) 3.0-4.5m (c)4.5-5.5m (d) >5.5m

Last Answer : (a) 1.5-3.0m

Speed of the cutter bar in case of combine (grain) is (a)400-550 rpm (b) 500-800rpm (c)800-1000rpm (d) 1000-1200rpm

Description : Speed of the cutter bar in case of combine (grain) is (a)400-550 rpm (b) 500-800rpm (c)800-1000rpm (d) 1000-1200rpm

Last Answer : a)400-550 rpm