Wait status can be achieved in 8085 microprocessor by : -

Wait status can be achieved in 8085 microprocessor by : - a) TRAP b) DMA c) HOLD d) INTR
by

1 Answer

Answer :

Wait status can be achieved in 8085 microprocessor by : - HOLD

by

Related questions

To put the 8085 microprocessor in the wait state(i) lower the-HOLD input (ii) lower the READY input (iii) raise the HOLD input(iv) raise the READY input

Description : To put the 8085 microprocessor in the wait state(i) lower the-HOLD input (ii) lower the READY input (iii) raise the HOLD input(iv) raise the READY input

Last Answer : (ii) lower the READY input

Which signal of 8085 microprocessor is used to insert wait states ?

Description : Which signal of 8085 microprocessor is used to insert wait states ?   (a) Ready (b) ALE (c) HOLD (d) INTR

Last Answer : Which signal of 8085 microprocessor is used to insert wait states ?   (a) Ready (b) ALE (c) HOLD (d) INTR

The contents of Register (BL) and Register (AL) of 8085 microprocessor are 49H and 3AH respectively. The contents of AL, the status of carry flag (CF) and sign flag (SF) after executing 'SUB AL, BL' assembly language instruction, are (1) AL=0FH; CF=1; SF=1 (2) AL=F0H; CF=0; SF=0 (3) AL=F1H; CF=1; SF=1 (4) AL=1FH; CF=1; SF=1

Description : The contents of Register (BL) and Register (AL) of 8085 microprocessor are 49H and 3AH respectively. The contents of AL, the status of carry flag (CF) and sign flag (SF) after executing 'SUB AL, BL' assembly language instruction, are ( ... ; CF=0; SF=0 (3) AL=F1H; CF=1; SF=1 (4) AL=1FH; CF=1; SF=1

Last Answer : Answer: 3

What is Microprocessor 8085?

Description : What is Microprocessor 8085?

Last Answer : 8085 is a 8 bit microprocessor designed by Intel.

What is the microprocessor - 8085 architecture?

Description : What is the microprocessor - 8085 architecture?

Last Answer : 8085 Architecture - II Written by: shankar â⠬¢ Edited by: KennethSleightPublished Sep 30, 2009 â⠬¢ Related Guides: IntelLearn in detail about the functions and working of flags, the timing ... ALU alone cannot successfully process a data and provide the result to the programmer. There are

List the four instructions which control the interrupt structure of the 8085 microprocessor.

Description : List the four instructions which control the interrupt structure of the 8085 microprocessor.

Last Answer : • DI ( Disable Interrupts ) • EI ( Enable Interrupts ) • RIM ( Read Interrupt Masks ) • SIM ( Set Interrupt Masks )

How many operations are there in the instruction set of 8085 microprocessor?

Description : How many operations are there in the instruction set of 8085 microprocessor?

Last Answer : There are 74 operations in the 8085 microprocessor.

List the 16 – bit registers of 8085 microprocessor.

Description : List the 16 – bit registers of 8085 microprocessor.

Last Answer : Stack pointer (SP) and Program counter (PC).

What is Microprocessor? Give the power supply & clock frequency of 8085

Description : What is Microprocessor? Give the power supply & clock frequency of 8085

Last Answer : A microprocessor is a multipurpose, programmable logic device that reads binary instructions from a storage device called memory accepts binary data as input and processes data according ... provides result as output. The power supply of 8085 is +5V and clock frequency in 3MHz.

The stack pointer in the 8085 microprocessor is a: a) 16 bit register that points to stack memory locations b) 16 bit accumulator c) Memory location in the stack d) None of The Above

Description : The stack pointer in the 8085 microprocessor is a: a) 16 bit register that points to stack memory locations b) 16 bit accumulator c) Memory location in the stack d) None of The Above

Last Answer : a) 16 bit register that points to stack memory locations

What type of architecture is used in 8085 microprocessor?

Description : What type of architecture is used in 8085 microprocessor?

Last Answer : Ans- INTEL 8085 is a 8-bit microprocessor. It's based on Von-Neumann architecture in which the data and instructions are in the same memory space without any distinction between them. Data line: 8-bits--Can ... of data at a time. Address line: 16-bits--Can address upto 2^16(64KB) of address space.

What is function of ALE in 8085 microprocessor?

Description : What is function of ALE in 8085 microprocessor?

Last Answer : Ans-AlE stands for the address latch enableit 's working is that it differentiate the address and data bus in microprocessor.when it is high it select address bus .when it is low it select data bus.

How many speed of 8088,8085,8086 microprocessor: a. 2.5 Million instruction per second b. 1.5 Million instruction per second c. 3.5 Million instruction per second d. 1.6 Million instruction per second

Description : How many speed of 8088,8085,8086 microprocessor: a. 2.5 Million instruction per second b. 1.5 Million instruction per second c. 3.5 Million instruction per second d. 1.6 Million instruction per second

Last Answer : a. 2.5 Million instruction per second

Which is 16 Bit microprocessor: a. 8088 b. 8086 c. 8085 d. All of these

Description : Which is 16 Bit microprocessor: a. 8088 b. 8086 c. 8085 d. All of these

Last Answer : d. All of these

The___ was very successful in the calculator market at that time: a. Motorola 6800 and 6809 b. Microprocessor 4004 c. Intel 8085 d. None of these

Description : The___ was very successful in the calculator market at that time: a. Motorola 6800 and 6809 b. Microprocessor 4004 c. Intel 8085 d. None of these

Last Answer : b. Microprocessor 4004

Microprocessor 8085 can address location upto a. 32K b. 128K c. 64K d. 1M

Description : Microprocessor 8085 can address location upto a. 32K b. 128K c. 64K d. 1M

Last Answer : c. 64K

In an 8085 microprocessor, the instruction CMP B has been executed while the contentsof accumulator is less than that of register B. As a result carry flag and zero flag will berespectively (A) set, reset (B) reset, set (C) reset, reset (D) set, set

Description : In an 8085 microprocessor, the instruction CMP B has been executed while the contentsof accumulator is less than that of register B. As a result carry flag and zero flag will berespectively (A) set, reset (B) reset, set (C) reset, reset (D) set, set

Last Answer : (A) set, reset

Accumulator based microprocessor example are: a. Intel 8085 b. Motorola 6809 c. A and B d. None of these

Description : Accumulator based microprocessor example are: a. Intel 8085 b. Motorola 6809 c. A and B d. None of these

Last Answer : c. A and B

Explain Briefly The Flag Register In The 8085 Microprocessor.?

Description : Explain Briefly The Flag Register In The 8085 Microprocessor.?

Last Answer : Answer :The flag register in 8085 is an 8-bit register which contains 5 bit positions. These five flags are of 1bit F/F and are known as zero, sign, carry, parity and auxiliary carry. ... addition and subtraction operations. The parity flag is used for results containing an even number of one's.

Mention The Various Functional Blocks Of The 8085 Microprocessor.?

Description : Mention The Various Functional Blocks Of The 8085 Microprocessor.?

Last Answer : Answer :The various functional blocks of the 8085 microprocessor are: Registers Arithmetic logic unit Address buffer Increment / decrement address latch Interrupt control Serial I/O control Timing and control circuitry Instructions decoder and machine cycle encoder.

How Can Signals Be Classified For The 8085 Microprocessor?

Description : How Can Signals Be Classified For The 8085 Microprocessor?

Last Answer : Answer :The signals of the 8085 microprocessor based on their functions can be classified into 7 categories namely: Frequency and power signals Address and data buses The control bus Interrupt Signals Serial Input / Output signals DMA signals Reset Signals

The RST 7 instruction in 8085 microprocessor is equivalent to: (A) CALL 0010 H (B) CALL 0034 H (C) CALL 0038 H (D) CALL 003C H

Description : The RST 7 instruction in 8085 microprocessor is equivalent to: (A) CALL 0010 H (B) CALL 0034 H (C) CALL 0038 H (D) CALL 003C H

Last Answer : (C) CALL 0038 H

Which of the following 8085 microprocessor hardware interrupt has the lowest priority? (A) RST 6.5 (B) RST 7.5 (C) TRAP (D) INTR

Description : Which of the following 8085 microprocessor hardware interrupt has the lowest priority? (A) RST 6.5 (B) RST 7.5 (C) TRAP (D) INTR 

Last Answer : Answer: D

Which of the following in 8085 microprocessor performs HL = HL + DE ? (A) DAD D (B) DAD H (C) DAD B (D) DAD SP

Description : Which of the following in 8085 microprocessor performs HL = HL + DE ? (A) DAD D (B) DAD H (C) DAD B (D) DAD SP

Last Answer : (A) DAD D

8085 microprocessor has ............. hardware interrupts. (A) 2 (B) 3 (C) 4 (D) 5

Description : 8085 microprocessor has ............. hardware interrupts. (A) 2 (B) 3 (C) 4 (D) 5

Last Answer : (D) 5

In 8085 microprocessor, the digit 5 indicates that the microprocessor needs (1) -5 volts, +5 volts supply (2) +5 volts supply only (3) -5 volts supply only (4) 5 MHz clock

Description : In 8085 microprocessor, the digit 5 indicates that the microprocessor needs (1) -5 volts, +5 volts supply (2) +5 volts supply only (3) -5 volts supply only (4) 5 MHz clock

Last Answer : Answer: 2

Enlist the features of 8085 microprocessor.

Description : Enlist the features of 8085 microprocessor.

Last Answer : Features of 8085 microprocessor: 1. 16 address line so 216=64 Kbytes of memory can be addressed. 2. Operating clock frequency is 3MHz and minimum clock  frequency is 500 KHz. 3. On chip bus ... cycle TTL clock 10. Provide 2 serial I/O lines, so peripheral can be interfaced with  8085 μp

State the functions of temporary registers of 8085 microprocessor.

Description : State the functions of temporary registers of 8085 microprocessor.

Last Answer : Temp Register (8 bits) is also called as operand register as it is used by μp for storing one of the operands during an operation and also for storing the result of any execution temproary.

List any four salient features of 8085 microprocessor

Description : List any four salient features of 8085 microprocessor

Last Answer : Features of 8085:  1. 16 address line so 216=64 Kbytes of memory can be addressed.  2. Operating clock frequency is 3MHz and minimum clock frequency is 500 KHz.  3. On chip bus controller ... duty cycle TTL clock  10. Provide 2 serial I/O lines, so peripheral can be interfaced with 8085 μp

The 8085 Microprocessor has

Description : The 8085 Microprocessor has A) 8-bits Data bus and 16-bits Address bus B) 8-bits Data bus and 8-bits Address bus C) 16-bits Data bus and 16-bits Address bus D) 32-bits Data bus and 8-bits Address bus 

Last Answer : B) 8-bits Data bus and 8-bits Address bus. 

The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse

Description : The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse width of the INTR signal so that it is recognized successfully? A) 5.6 µs B) 5.7 µs C) 5.8 µs D) 5.9 µs

Last Answer : The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse width of the INTR signal so that it is recognized successfully? A) 5.6 µs B) 5.7 µs C) 5.8 µs D) 5.9 µs

In 8085 microprocessor, how many T-states does OPCODE FETCH machine cycle normally require

Description : In 8085 microprocessor, how many T-states does OPCODE FETCH machine cycle normally require (i.e., when HOLD and WAIT signals are NOT forced)? A) 4 to 6 B) 3 to 8 C) 2 to 3 D) 8 to 12 

Last Answer : In 8085 microprocessor, how many T-states does OPCODE FETCH machine cycle normally require (i.e., when HOLD and WAIT signals are NOT forced)? A) 4 to 6 B) 3 to 8 C) 2 to 3 D) 8 to 12 

Then number of T-states of the instruction STA in 8085 microprocessor is

Description : Then number of T-states of the instruction STA in 8085 microprocessor is A) 10 B) 12 C) 13 D) 16 

Last Answer : Then number of T-states of the instruction STA in 8085 microprocessor is 13 

What is the size of memory which can be accessed by direct accessing in 8085 microprocessor?

Description : What is the size of memory which can be accessed by direct accessing in 8085 microprocessor? A) 64 kB B) 4 kB C) 128 kB D) 128 MB 

Last Answer : What is the size of memory which can be accessed by direct accessing in 8085 microprocessor? A) 64 kB B) 4 kB C) 128 kB D) 128 MB 

What is the size of SP register in 8085 microprocessor?

Description :  What is the size of SP register in 8085 microprocessor? A) 16 bits B) 8 bits C) 64 bits D) 48 bits

Last Answer :  What is the size of SP register in 8085 microprocessor? A) 16 bits B) 8 bits C) 64 bits D) 48 bits

In an 8085 microprocessor, after the execution of XRA A instruction

Description : In an 8085 microprocessor, after the execution of XRA A instruction A) the carry flag is set B) the accumulator contains FFH C) the zero flag is set D) the accumulator contents are shifted left by one bit

Last Answer :  In an 8085 microprocessor, after the execution of XRA A instruction the zero flag is set 

In 8085 microprocessor, the value of the most significant bit of the result following the execution of any

Description : In 8085 microprocessor, the value of the most significant bit of the result following the execution of any arithmetic of Boolean instruction is stored in the (1) Carry status flag (2) Auxiliary carry status flag (3) Sign status flag (4) Zero status flag

Last Answer : In 8085 microprocessor, the value of the most significant bit of the result following the execution of any arithmetic of Boolean instruction is stored in the Sign status flag

8085 microprocessor has ________ individual flags during arithmetic and logic operations.

Description : 8085 microprocessor has ________ individual flags during arithmetic and logic operations.

Last Answer : 8085 microprocessor has 5 individual flags during arithmetic and logic operations.

When a program is being executed in an 8085 microprocessor, its Program Counter contains

Description : When a program is being executed in an 8085 microprocessor, its Program Counter contains  (A) the number of instructions in the current program that have already been executed (B) the total number ... is being currently executed (D) the memory address of the instruction that is to be executed next

Last Answer : When a program is being executed in an 8085 microprocessor, its Program Counter contains the memory address of the instruction that is to be executed next

In an 8085 microprocessor, the contents of the Accumulator, after the following instructions are executed

Description : In an 8085 microprocessor, the contents of the Accumulator, after the following instructions are executed will become   XRA A   MVI B, F0 H   SUB B  (A) 01 H (B) 0F H (C) F0 H (D) 10 H

Last Answer : In an 8085 microprocessor, the contents of the Accumulator, after the following instructions are executed will become   XRA A   MVI B, F0 H   SUB B  (A) 01 H (B) 0F H (C) F0 H (D) 10 H

Intel's 8085 microprocessor chip contains

Description : Intel's 8085 microprocessor chip contains  (A) seven 8 bit registers (B) 8 seven bits registers (C) seven 7 bit registers (D) eight 8 bit registers.

Last Answer : Intel's 8085 microprocessor chip contains seven 8 bit registers

Consider the following program segment with 8085 microprocessor

Description : Consider the following program segment with 8085 microprocessor  LXI H 3600H  MOV A, M  HLT  The MOV instruction involves (a) indirect addressing (b) immediate addressing (c) implicit addressing (d) direct addressing

Last Answer : Consider the following program segment with 8085 microprocessor  LXI H 3600H  MOV A, M  HLT  The MOV instruction involves (a) indirect addressing (b) immediate addressing (c) implicit addressing (d) direct addressing

To establish a communication between 8085 microprocessor and 8255 Programmable Peripheral Interface

Description : To establish a communication between 8085 microprocessor and 8255 Programmable Peripheral Interface chip. the status of the chip select input would be  (a) TRISTATE (b) HIGH (b) LOW (d) DON’T CARE 

Last Answer : To establish a communication between 8085 microprocessor and 8255 Programmable Peripheral Interface chip. the status of the chip select input would be  (a) TRISTATE (b) HIGH (b) LOW (d) DON’T CARE 

Which flag does not change by the execution of the instruction DCR B in 8085 microprocessor ?

Description : Which flag does not change by the execution of the instruction DCR B in 8085 microprocessor ?  (a) Parity (b) Carry (c) Zero (d) Sign

Last Answer : Which flag does not change by the execution of the instruction DCR B in 8085 microprocessor ?  (a) Parity (b) Carry (c) Zero (d) Sign

The zero flag of 8085 microprocessor is to be set keeping the content of the accumulator unchanged.

Description : The zero flag of 8085 microprocessor is to be set keeping the content of the accumulator unchanged. Which instruction is to be used?  (a) MOV A,A (b) ANI 00H (c) XRA A (d) CMP A

Last Answer : The zero flag of 8085 microprocessor is to be set keeping the content of the accumulator unchanged. Which instruction is to be used?  (a) MOV A,A (b) ANI 00H (c) XRA A (d) CMP A

The 8085 is a – microprocessor

Description : The 8085 is a – microprocessor   1. 4 bit 2. 8 bit 3. 16 bit 4. 32 bit 

Last Answer : The 8085 is a 8 bit microprocessor

In an 8085 microprocessor, the contents of accumulator, after the following instructions are

Description : In an 8085 microprocessor, the contents of accumulator, after the following instructions are executed will become   XRA A   MVI B F0H   SUB B   (a) 01 H (b) 0F H (c) F0 H (d) 10 H

Last Answer : In an 8085 microprocessor, the contents of accumulator, after the following instructions are executed will become   XRA A   MVI B F0H   SUB B   (a) 01 H (b) 0F H (c) F0 H (d) 10 H

Which of the following instructions is not available in 8085 microprocessor?

Description : Which of the following instructions is not available in 8085 microprocessor? (A) LDA 3850 (B) XTHL (C) push PSW (D) LDAXH

Last Answer : Which of the following instructions is not available in 8085 microprocessor? (A) LDA 3850 (B) XTHL (C) push PSW (D) LDAXH

The ALE line of an 8085 microprocessor is used to

Description : The ALE line of an 8085 microprocessor is used to (A) latch the output of an I/O instruction into an external latch. (B) deactivate the chip-select signal from memory devices. (C) find the interrupt ... of the TRAP interrupt. (D) latch the 8 bits of address lines AD7-AD0 into an external latch.

Last Answer : The ALE line of an 8085 microprocessor is used to latch the 8 bits of address lines AD7-AD0 into an external latch.

In 8085 microprocessor with memory mapped I/O which of the following is true?

Description : In 8085 microprocessor with memory mapped I/O which of the following is true?  (1) I/O devices have 16 bit addresses (2) I/O devices are accessed during IN and OUT instructions (3) There can be a maximum of 256 input and 256 output devices (4) Logic operations can not be performed

Last Answer : I/O devices have 16 bit addresses.