The material used for making torsion bar is (a) Steel (b) Cast iron (c) High carbon steel (d) All of the above

The material used for making torsion bar is
(a) Steel (b) Cast iron (c) High carbon steel (d) All of the above
by

1 Answer

Answer :

(a) Steel
by

Related questions

Which material is suitable for shaft material? a. High speed steel b. Stainless steel or high carbon steel c. Grey cast iron d. Steel having approx. 0.4% carbon and 0.8% manganese

Description : Which material is suitable for shaft material? a. High speed steel b. Stainless steel or high carbon steel c. Grey cast iron d. Steel having approx. 0.4% carbon and 0.8% manganese

Last Answer : d. Steel having approx. 0.4% carbon and 0.8% manganese

Flexible shafts have ___ rigidity in torsion making them flexible. a) Low b) High c) Very high d) Infinitely small

Description : Flexible shafts have ___ rigidity in torsion making them flexible. a) Low b) High c) Very high d) Infinitely small

Last Answer : b) High

The shafts are made of a. mild steel b. alloy steel c. copper alloys d. cast iron.

Description : The shafts are made of a. mild steel b. alloy steel c. copper alloys d. cast iron.

Last Answer : d. cast iron.

Which of the following assumptions are made in torsion theory? a. Shaft is perfectly straight b. Material of the shaft is heterogeneous c. Twist cannot be uniform along the length of the shaft d. Shaft is perfectly curve

Description : Which of the following assumptions are made in torsion theory? a. Shaft is perfectly straight b. Material of the shaft is heterogeneous c. Twist cannot be uniform along the length of the shaft d. Shaft is perfectly curve v

Last Answer : a. Shaft is perfectly straight b. Material of the shaft is heterogeneous

Which of the following is not an assumption in derivation of torsion equation? a. Circular shaft remains circular after twisting b. Plane section of the shaft remain plane after twisting c. Material of shaft is isotropic d. Angle of twist is proportional to radius

Description : Which of the following is not an assumption in derivation of torsion equation? a. Circular shaft remains circular after twisting b. Plane section of the shaft remain plane after twisting c. Material of shaft is isotropic d. Angle of twist is proportional to radius

Last Answer : d. Angle of twist is proportional to radius

Two shafts in torsion will have equal strength if a. Only diameter of the shafts is same b. Only angle of twist of the shaft is same c. Only material of the shaft is same d. Only torque transmitting capacity of the shaft is same

Description : Two shafts in torsion will have equal strength if a. Only diameter of the shafts is same b. Only angle of twist of the shaft is same c. Only material of the shaft is same d. Only torque transmitting capacity of the shaft is same

Last Answer : d. Only torque transmitting capacity of the shaft is same

The ratio of strength of a hollow shaft to that of a solid shaft subjected to torsion if both are of the same material and of the same outer diameters, the inner diameter of hollow shaft being half of the outer diameter is a. 15/16 b. 16/15 c. 7/8 d. 8/7

Description : The ratio of strength of a hollow shaft to that of a solid shaft subjected to torsion if both are of the same material and of the same outer diameters, the inner diameter of hollow shaft being half of the outer diameter is a. 15/16 b. 16/15 c. 7/8 d. 8/7

Last Answer : a. 15/16

The type of spring used to achieve any linear and non-linear load-deflection characteristics is (a)spiral spring (b) non-ferrous spring (c)Belleville spring (d) torsion spring

Description : The type of spring used to achieve any linear and non-linear load-deflection characteristics is (a)spiral spring (b) non-ferrous spring (c)Belleville spring (d) torsion spring

Last Answer : (c)Belleville spring

When a close-coiled helical spring is subjected to an axial load, it is said to be under. (a) Bending (b) Shear (c) Torsion (d) Crushing

Description : When a close-coiled helical spring is subjected to an axial load, it is said to be under. (a) Bending (b) Shear (c) Torsion (d) Crushing

Last Answer : (c) Torsion

Which of the following loading is considered for the design of axles ? (a) Bending moment only (b) Twisting moment only (c) Combined bending moment and torsion (d) Combined action of bending moment, twisting moment and axial thrust

Description : Which of the following loading is considered for the design of axles ? (a) Bending moment only (b) Twisting moment only (c) Combined bending moment and torsion (d) Combined action of bending moment, twisting moment and axial thrust

Last Answer : (a) Bending moment only

The ratio of strengths of solid to hollow shafts, both having outside diameter D and hollow having inside diameter D/2, in torsion, is a.1/4 b. 1/2 c. 1/16 d. 15/16

Description : The ratio of strengths of solid to hollow shafts, both having outside diameter D and hollow having inside diameter D/2, in torsion, is a.1/4 b. 1/2 c. 1/16 d. 15/16

Last Answer : d. 15/16

A circular shaft subjected to torsion undergoes a twist of 10in a length of 120 cm. If the maximum shear stress induced is limited to 1000 kg/cm2and if modulus of rigidity G = 0.8 x 106then the radius of the shaft should be (a) p/8 (b) p/27 (c) 18/p (d) 27/p

Description : A circular shaft subjected to torsion undergoes a twist of 10in a length of 120 cm. If the maximum shear stress induced is limited to 1000 kg/cm2and if modulus of rigidity G = 0.8 x 106then the radius of the shaft should be (a) p/8 (b) p/27 (c) 18/p (d) 27/p

Last Answer : (d) 27/p

A member subjected to couple produces rotational motion about its longitudinal axis called as ________ a. torsion b. twisting moment c. both a. and b. d. bending moment

Description : A member subjected to couple produces rotational motion about its longitudinal axis called as ________ a. torsion b. twisting moment c. both a. and b. d. bending moment

Last Answer : c. both a. and b.

A shaft a. Is always subjected to pure torsion b. Combination of M & T but no end thrust c. Combination of torque & end thrust but no bending moment d. May be subjected to a combination of M, T and end thrust

Description : A shaft a. Is always subjected to pure torsion b. Combination of M & T but no end thrust c. Combination of torque & end thrust but no bending moment d. May be subjected to a combination of M, T and end thrust

Last Answer : d. May be subjected to a combination of M, T and end thrust

In combined bending and torsion equivalent bending moment is a. Me = (M^2 + T^2)^1/2 b. Me = ½(M^2 + T^2)^1/2 c. Me = M+(M^2 + T^2)^1/2 d. Me = 1/2 [M+(M^2 + T^2)^1/2]

Description : In combined bending and torsion equivalent bending moment is a. Me = (M^2 + T^2)^1/2 b. Me = ½(M^2 + T^2)^1/2 c. Me = M+(M^2 + T^2)^1/2 d. Me = 1/2 [M+(M^2 + T^2)^1/2]

Last Answer : d. Me = 1/2 [M+(M^2 + T^2)^1/2]

Equivalent torque in combined bending and torsion is given by a. Te = (M^2 + T^2)^1/2 b. Te = ½(M^2 + T^2)^1/2 c. Te = M + T d. Te = 1/2 [M+(M^2 + T^2)^1/2]

Description : Equivalent torque in combined bending and torsion is given by a. Te = (M^2 + T^2)^1/2 b. Te = ½(M^2 + T^2)^1/2 c. Te = M + T d. Te = 1/2 [M+(M^2 + T^2)^1/2]

Last Answer : a. Te = (M^2 + T^2)^1/2

Which of the following is incorrect? a. In torsion equation, we use mean torque b. In torsion equation, we use maximum torque c. Many shafts are designed under combined bending and torsion load d. Shafts are also designed for torsional rigidity

Description : Which of the following is incorrect? a. In torsion equation, we use mean torque b. In torsion equation, we use maximum torque c. Many shafts are designed under combined bending and torsion load d. Shafts are also designed for torsional rigidity

Last Answer : a. In torsion equation, we use mean torque

Which of the following is not designed under torsion equation? a. Spindle b. Axle c. Low cost shaft d. Shaft with variable diameter

Description : Which of the following is not designed under torsion equation? a. Spindle b. Axle c. Low cost shaft d. Shaft with variable diameter

Last Answer : b. Axle

A shaft is said to be in pure torsion if a. Turning moment is applied at one end and other end is free b. Turning force is applied at one end and other end is free c. Two opposite turning moments are applied to the shaft d. Combination of torsional load and bending load is applied to the shaft

Description : A shaft is said to be in pure torsion if a. Turning moment is applied at one end and other end is free b. Turning force is applied at one end and other end is free c. Two opposite turning moments are applied to the shaft d. Combination of torsional load and bending load is applied to the shaft

Last Answer : c. Two opposite turning moments are applied to the shaft

The variation of shear stress in a circular shaft subjected to torsion is a. Linear b. Parabolic c. Hyperbolic. d. Uniform

Description : The variation of shear stress in a circular shaft subjected to torsion is a. Linear b. Parabolic c. Hyperbolic. d. Uniform

Last Answer : a. Linear

A short, hollow cast iron cylinder with a wall thickness of 1 cm is to carry a compressive load of 10 tonnes. If the working stress in compression is 800 kg/cm2, the outside diameter of the cylinder should not be less than a) 0.5cm b) 5 cm c) 2.5cm d) 4.5 cm

Description : A short, hollow cast iron cylinder with a wall thickness of 1 cm is to carry a compressive load of 10 tonnes. If the working stress in compression is 800 kg/cm2, the outside diameter of the cylinder should not be less than a) 0.5cm b) 5 cm c) 2.5cm d) 4.5 cm

Last Answer : b) 5 cm

Cutter Bar made of a) Copper b) High Grade Steel c) Cast iron d) None of the above

Description : Cutter Bar made of a) Copper b) High Grade Steel c) Cast iron d) None of the above

Last Answer : High Grade Steel

Aqueous nitric acid is stored in __________ vessel. (A) Plain carbon steel (B) Stainless steel (C) Cast iron (D) Thermosetting plastic material

Description : Aqueous nitric acid is stored in __________ vessel. (A) Plain carbon steel (B) Stainless steel (C) Cast iron (D) Thermosetting plastic material

Last Answer : (C) Cast iron

Elongation of a bar of uniform cross section of length ‘L’, due to its own weight ‘W’ is given by a. 2WL/E b. WL/E c. WL/2E d. WL/3E Where, E=Young’s modulus of elasticity of material

Description : Elongation of a bar of uniform cross section of length ‘L’, due to its own weight ‘W’ is given by a. 2WL/E b. WL/E c. WL/2E d. WL/3E Where, E=Young’s modulus of elasticity of material

Last Answer : c. WL/2E

The total extension in a bar, consists of 3 bars of same material, of varying sections is a. P/E(L1/A1+L2/A2+L3/A3) b. P/E(L1A1+L2A2+L3A3) c. PE(L1/A1+L2/A2+L3/A3) d. PE(L1/A1+L2/A2+L3/A3)

Description : The total extension in a bar, consists of 3 bars of same material, of varying sections is a. P/E(L1/A1+L2/A2+L3/A3) b. P/E(L1A1+L2A2+L3A3) c. PE(L1/A1+L2/A2+L3/A3) d. PE(L1/A1+L2/A2+L3/A3)

Last Answer : a. P/E(L1/A1+L2/A2+L3/A3)

Which property is not required for shaft materials? a. High shear and tensile strength b. Good mach inability c. High fatigue strength d. Good cast ability

Description : Which property is not required for shaft materials? a. High shear and tensile strength b. Good mach inability c. High fatigue strength d. Good cast ability

Last Answer : d. Good cast ability

With the increase of carbon content in steel, maximum stress (A) Increases (b) Decreases (C) Remains the same (d) none

Description : With the increase of carbon content in steel, maximum stress (A) Increases (b) Decreases (C) Remains the same (d) none

Last Answer : (A) Increases

Which of the following material is more elastic? (a) Rubber (b) Glass (c) Steel (d) Wood

Description : Which of the following material is more elastic? (a) Rubber (b) Glass (c) Steel (d) Wood

Last Answer : (c) Steel

Which one of the following contains maximum percentage of carbon? (1) Cast iron (2) Stainless steel (3) Wrought iron (4) High speed steel

Description : Which one of the following contains maximum percentage of carbon? (1) Cast iron (2) Stainless steel (3) Wrought iron (4) High speed steel

Last Answer : (1) Cast iron Explanation: Cast Iron is a hard, brittle, nonmalleable iron-carbon alloy, cast into shape, containing 2 to 4.5 percent carbon. Steels contain less than 2% and usually less than 1% carbon, ... percent carbon. Wrought iron is an iron alloy with very low carbon (0.04 to 0.08%) content.

Which one contains the least percentage of carbon?(A) Wrought iron (B) High speed steel (C) Cast iron (D) Pig iron

Description : Which one contains the least percentage of carbon? (A) Wrought iron (B) High speed steel (C) Cast iron (D) Pig iron

Last Answer : (A) Wrought iron

Carbon percentage is the same in cast iron and (A) Wrought iron(B) Pig iron(C) Mild steel(D) High silicon (14%) iron

Description : Carbon percentage is the same in cast iron and (A) Wrought iron (B) Pig iron (C) Mild steel (D) High silicon (14%) iron

Last Answer : (B) Pig iron

Water gas generator is made of (A) Carbon steel-brick lined (B) Stainless steel-lead lined (C) Cast iron (D) High carbon steel-porcelain lined

Description : Water gas generator is made of (A) Carbon steel-brick lined (B) Stainless steel-lead lined (C) Cast iron (D) High carbon steel-porcelain lined

Last Answer : (A) Carbon steel-brick lined

Which of the following has the highest compressive strength? (A) Wrought iron (B) Cast iron (C) Mild steel (D) High carbon steel

Description : Which of the following has the highest compressive strength? (A) Wrought iron (B) Cast iron (C) Mild steel (D) High carbon steel

Last Answer : (D) High carbon steel

Mixing vessel used for the chlorination of methane to produce methyl chloride is made of (A) Copper (B) Cast iron (C) Aluminium (D) High carbon steel

Description : Mixing vessel used for the chlorination of methane to produce methyl chloride is made of (A) Copper (B) Cast iron (C) Aluminium (D) High carbon steel

Last Answer : (B) Cast iron

Which of the following has the least value of ultimate tensile strength (UTS)? (A) Medium carbon steel (B) High carbon steel (C) Cast iron (D) Wrought iron Answer: Option C

Description : Which of the following has the least value of ultimate tensile strength (UTS)? (A) Medium carbon steel (B) High carbon steel (C) Cast iron (D) Wrought iron Answer: Option C

Last Answer : (C) Cast iron

Oxyacetylene reducing flame is used while carrying out welding on (A) Alloy steel (B) Grey cast iron (C) Mild steel (D) High carbon steel

Description : Oxyacetylene reducing flame is used while carrying out welding on (A) Alloy steel (B) Grey cast iron (C) Mild steel (D) High carbon steel

Last Answer : (C) Mild steel

Oxyacetylene reducing flame is used while carrying out welding on (A) Alloy steel (B) Grey cast iron (C) Mild steel (D) High carbon steel

Description : Oxyacetylene reducing flame is used while carrying out welding on (A) Alloy steel (B) Grey cast iron (C) Mild steel (D) High carbon steel

Last Answer : Option C

Which of the following has the least value of ultimate tensile strength (UTS)? (A) Medium carbon steel (B) High carbon steel (C) Cast iron (D) Wrought iron

Description : Which of the following has the least value of ultimate tensile strength (UTS)? (A) Medium carbon steel (B) High carbon steel (C) Cast iron (D) Wrought iron

Last Answer : Option B

Which of the following is the purest form of iron? (A) Cast iron (B) Wrought iron (C) Mild steel (D) High carbon steel

Description : Which of the following is the purest form of iron? (A) Cast iron (B) Wrought iron (C) Mild steel (D) High carbon steel

Last Answer : Answer: Option B

______is extensively used for those portions of magnetic circuit which carry steady flux and need superior mechanical properties ? (a) Grey cast-iron (b) Cast steel (c) High carbon steel (d) Stainless steel

Description : ______is extensively used for those portions of magnetic circuit which carry steady flux and need superior mechanical properties ? (a) Grey cast-iron (b) Cast steel (c) High carbon steel (d) Stainless steel

Last Answer : (b) Cast steel

Which one of the following contains maximum percentage of carbon ? (1) Cast iron (2) Stainless steel (3) Wrought iron (4) High speed steel

Description : Which one of the following contains maximum percentage of carbon ? (1) Cast iron (2) Stainless steel (3) Wrought iron (4) High speed steel

Last Answer : Cast iron

Which of the following material of construction may be recommended by a chemical engineer for handling a gaseous chlorine (dry or wet) stream in a fluid flow system? (A) High silicon iron, silicon rubber, Kel-F and Teflon (B) Mild steel and stainless steel (C) Cast iron, tin and aluminium (D) Copper, nickel and Monel

Description : Which of the following material of construction may be recommended by a chemical engineer for handling a gaseous chlorine (dry or wet) stream in a fluid flow system? (A) High silicon iron, silicon rubber ... Mild steel and stainless steel (C) Cast iron, tin and aluminium (D) Copper, nickel and Monel

Last Answer : (A) High silicon iron, silicon rubber, Kel-F and Teflon

Highest cutting speed is achieved by the __________ tool material. (A) High speed steel (B) Carbide (C) Cast alloy (D) Plain carbon steel

Description : Highest cutting speed is achieved by the __________ tool material. (A) High speed steel (B) Carbide (C) Cast alloy (D) Plain carbon steel

Last Answer : (B) Carbide

Cutter bar is made up of which material a) High grade steel. b) Low carbon alloy steel. c) Platinum. d) High speed tool steel

Description : Cutter bar is made up of which material a) High grade steel. b) Low carbon alloy steel. c) Platinum. d) High speed tool steel

Last Answer : High grade steel

Which of the following has the least carbon percentage? (A) Low carbon steel (B) Mild steel (C) Wrought iron (D) White cast iron

Description : Which of the following has the least carbon percentage? (A) Low carbon steel (B) Mild steel (C) Wrought iron (D) White cast iron

Last Answer : (C) Wrought iron

Which one is remelted and poured into moulds to get cast iron? (A) Wrought iron (B) Pig iron (C) Low carbon steel (D) Mild steel

Description : Which one is remelted and poured into moulds to get cast iron? (A) Wrought iron (B) Pig iron (C) Low carbon steel (D) Mild steel

Last Answer : (B) Pig iron

In the Kraft (sulphate) process for the paper manufacture, the digestor is made of (A) Cast iron (B) Stainless steel (C) Karbate carbon (D) Wrought iron

Description : In the Kraft (sulphate) process for the paper manufacture, the digestor is made of (A) Cast iron (B) Stainless steel (C) Karbate carbon (D) Wrought iron

Last Answer : (B) Stainless steel

Ball bearings are generally made of (A) Plain carbon steel (B) Chrome carbon steel (C) Stainless steel (D) Malleable cast iron

Description : Ball bearings are generally made of (A) Plain carbon steel (B) Chrome carbon steel (C) Stainless steel (D) Malleable cast iron

Last Answer : (B) Chrome carbon steel

Carbon is present in the uncombined (graphitic) form in case of (A) Cast iron (B) Steel (C) Ferroalloy (D) None of these

Description : Carbon is present in the uncombined (graphitic) form in case of (A) Cast iron (B) Steel (C) Ferroalloy (D) None of these

Last Answer : (A) Cast iron

Galvanising is generally done on (A) Non-ferrous metals (B) Low carbon steel (C) Stainless steel (D) Cast iron

Description : Galvanising is generally done on (A) Non-ferrous metals (B) Low carbon steel (C) Stainless steel (D) Cast iron

Last Answer : (B) Low carbon steel