Description : Cutter Bar made of a) Copper b) High Grade Steel c) Cast iron d) None of the above
Last Answer : High Grade Steel
Description : Highest cutting speed is achieved by the __________ tool material. (A) High speed steel (B) Carbide (C) Cast alloy (D) Plain carbon steel
Last Answer : (B) Carbide
Description : Steel containing low percentage of nickel, chromium & tungsten are termed as the __________ steel. (A) Wrought (B) Tool (C) Alloy (D) Plain carbon
Last Answer : (D) Plain carbon
Description : Pick out the wrong statement. (A) Weldability of high carbon steel is poorer compared to low carbon steel (B) Invar is a magnetic alloy (C) Magnetic permeability of the diamagnetic material is less than one (D) Martenistic transformation never goes to completion (i.e., 100%) at room temperature
Last Answer : Option B
Description : The distance of a given tool tip from the surface of workpiece is known as….. a.Tool length b.Tool length offset H c.Cutter radius d.Compensation
Last Answer : b.Tool length offset H
Description : Alignment of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. b
Last Answer : ans b
Description : Registration of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. a
Last Answer : ans a
Description : cutter bar knife a) triangular shape b) square shape c) trapezoidal shape d) curved shape Ans. c
Last Answer : ans c
Description : Registration of a cutter bar means a) Centre of knife must stop in the centre of guard on each stroke b) Centre of knife should be ahead of guard c) Centre of knife should be behind the guard d) Centre of knife should be at the end of the guard
Description : The cutter bar is set at about to the direction of motion in order to overcome the back-pushing action of the crops. a. 90° with inward lead of 2° c. 92° with inward lead of 2° d. None of above
Last Answer : Ans- b. 88° with inward lead of 2°
Description : It is always provided on each end of the cutter bar to regulate the height of cut and to provide easy and smooth sliding of the cutter bar on the land. b. Plate c. pitman d. None of above
Last Answer : Ans- b. shoe
Description : is part of the Cutter bar is shaped in Triangular shape with two cutting edges a) Knife head b) Knife back c) Grass board d) Knife Section
Last Answer : <!-- [endif] -->Knife Section
Description : Play in bearings and worn knife head holders caused due to in cutter bar. A) Pitman B) Breaking of knives. C) Knife head. D) Grass board.
Last Answer : Breaking of knives.
Description : In vertical conveyor reaper, the crop to be harvested are guided by a) Star wheel b) Reel c) Row divider d) Cutter bar
Last Answer : Star wheel
Description : are the labelling of cutter bar. a) Shoe, ledger plate, wearing plate, knife, knife section, etc. b) Star wheel, engine, cage wheel, etc. c) both A & B d) Conveyor belt, cutter bar, rivers, etc
Last Answer : Shoe, ledger plate, wearing plate, knife, knife section, etc.
Description : is the length of cutter bar which is recommended as per the standard of design of it. a) 4cm b) 6cm c) 2cm d) 3cm
Last Answer : 2cm
Description : At what degree does the cutter bar is set for achieving the object ? a) 96 b) 88 c) 69 and half. d) 105
Last Answer : 88
Description : is an assembly comparing of fingers, knife guides on wearing plates and shoe. a) Cutter bar b) Knife section c) Pitman d) Shoe
Last Answer : Cutter bar
Description : Which of the following pairs of elements may form an alloy? (A) Iron & carbon (B) Iron & mercury (C) Platinum & mercury (D) None of these
Last Answer : (A) Iron & carbon
Description : For spinning viscose rayon, the extrusion spinnerettes are made of (A) Platinum or gold alloys (B) High carbon steel (C) Aluminium (D) Nickel
Last Answer : (A) Platinum or gold alloys
Description : Mild steel is a/an __________ steel. (A) Low carbon (B) Medium carbon (C) High carbon (D) High alloy
Last Answer : (A) Low carbon
Description : Which of the following is the costliest material of construction used in pressure vessel construction? (A) Low alloy steel (B) Lead (C) Titanium (D) High alloy steel
Last Answer : (C) Titanium
Description : knives of the cutter bar are scrratedin order to a)Increase the co-efficient of friction between crop stalk machine b)Reducing the deflection of stalk side ways c)To increase the cutting speed d)To improve cutting height
Last Answer : a)Increase the co-efficient of friction between crop stalk machine
Description : Speed of the cutter bar in case of combine (grain) is (a)400-550 rpm (b) 500-800rpm (c)800-1000rpm (d) 1000-1200rpm
Last Answer : a)400-550 rpm
Description : Speed of the cutter bar in case of combine (grain) is :- a) 400 – 550 rpm b) 500 – 800 rpm C) 800 - 1000 rpm d) 1000 – 1200 rpm
Last Answer : a) 400 – 550 rpm
Description : type of connecting rod which is pinned to the crankshaft with the help of a pin, which helps to transmit the cut material. a) Pitman b) Cutter bat c) Shoe d) Wearing plate
Last Answer : Pitman
Description : __________ of hard alloy and tool steel is done to make it easily machinable. (A) Case carburising (B) Tempering (C) Normalising (D) Annealing
Last Answer : (B) Tempering
Description : Weld decay occurs in which of the following steel types? a) Carbon/Manganese b) Low alloy c) Any stainless steel d) Austenitic stainless steels
Last Answer : d) Austenitic stainless steels
Description : Transformer cores are laminated with (A) Low carbon steel. (B) Silicon sheet steel. (C) Nickel alloy steel. (D) Chromium sheet steel.
Last Answer : (B) Silicon sheet steel.
Description : The material used for making torsion bar is (a) Steel (b) Cast iron (c) High carbon steel (d) All of the above
Last Answer : (a) Steel
Description : Drills are usually made of (A) Cermets (B) High speed steel (C) Alloy steel (D) Tungsten carbide
Description : Stellite is a __________ material. (A) Ferrous (B) Ceramic (C) Cemented carbide (D) Non-ferrous cast alloy cutting tool
Last Answer : (D) Non-ferrous cast alloy cutting tool
Description : Roller chains are used for: a)Higher speed and higher loads b)made of high grade steel c)components are harden and polished d)All of the above
Last Answer : d)All of the above
Description : Two alloys contain platinum and gold in the ratio of 1:2 and 1:3 respectively. A third alloy C is formed by mixing alloys one and alloy two in the ratio of 3:4. Find the percentage of gold in the mixture a) 79.2/7% b) 71.2/7% c) 73.2/7% d) 71.3/7% e) None of these
Last Answer : Answer: D Platinum = 1/3 and 1/4 gold = 2/3 and 3/4 Alloy one and two are mixed in the ratio of 3:4, so ratio of platinum and gold in final ratio – 2:5 So gold % = (5/7)*100 71.3/7%
Description : Liners of a ball mill are never made of (A) Lead (B) Alloy steel (C) Rubber or ceramic material (D) Cast iron
Last Answer : (A) Lead
Description : Capacity of field choppers (chaff cutter) is affected by.... (a) Capacity of the feed mechanism (cross-sectional area) (b) Rate of advance of material through throat considered as to be same linear speed of feed mechanism (c) Density of forage material (d) All of the above
Last Answer : (d) All of the above
Description : Capacity of field choppers (chaff cutter) is affected by (a)capacity of the feed mechanism (cross sectional area) (b)Rate of advance of material through throat considered as to be the same linear speed of feed mechanism (c) density of forage material (d) all of the above
Last Answer : (d) all of the above
Description : An alloy of iron containing 4% carbon is called (A) High carbon steel (B) Wrought iron (C) Mild steel (D) None of these
Last Answer : (D) None of these
Description : Oxyacetylene reducing flame is used while carrying out welding on (A) Alloy steel (B) Grey cast iron (C) Mild steel (D) High carbon steel
Last Answer : (C) Mild steel
Last Answer : Option C
Description : Which of the following is not a tractor drawn primary tillage tool? 1. Disc plough 2. rotavator 3. Country plough 4. Bar harrow
Last Answer : ans 3
Description : Pick up reels are very effective in :- a) Cutting of upright crops b) Lifting of lodged (down) crops ahead of cutter bar C) Both (a) and (b) are true d) None of the above
Last Answer : C) Both (a) and (b) are true
Description : A steel alloy containing 36% nickel is called __________, which has a zero co-efficient of expansion. (A) Austenitic stainless steel (B) Heat resisting steel (C) Invar (D) High speed steel
Last Answer : (C) Invar
Description : __________ is the trade name assigned to a non-ferrous cast alloy composed of cobalt, chromium & tungsten. (A) Stellite (B) High speed steel (C) Cermet (D) Alnico
Last Answer : Option A
Description : The steel used in steel cored conductors is usually (a) alloy steel (b) stainless steel (c) mild steel (d) high speed steel (e) all of the above
Last Answer : (c) mild steel
Description : The cutter bar of a tractor operated on owner makes strokes/min (a) 400 – 500 (b) 500 – 750 (c) 800 – 1200 (d) 1250 – 1500
Last Answer : (c) 800 – 1200
Description : The cutter bar of a tractor operated mower ordinarily makes: A. Near the front axis B. 40mm towards the real axis C. At the power take off shaft D. Between the two lower Links
Last Answer : D. Between the two lower Links
Description : The cutter bar of a tractor operated mower ordinarily makes: A. 800-1200 strokes/min B. 1600-2000 strokes/min C. 2400-2800 strokes/min D. 3200-3600 strokes/min
Last Answer : A. 800-1200 strokes/min
Description : o over come the rear ward deflection the load given to outer end of the cutter bar is about..... (a)1.57cm/m (b) 2.0cm/m (b)3.0cm/m (d) 3.5cm/m
Last Answer : b) 2.0cm/m