Description : The input impedance of your test equipment should exceed the impedance of the circuit under test by what ratio?
Last Answer : 10 to 1
Description : In a parallel-resonant circuit, what is the relationship between impedance and current?
Last Answer : Maximum impedance, minimum current.
Description : . In an "ideal" resonant circuit, what is the relationship between impedance and current?
Last Answer : Impedance low Current high.
Description : If the output impedance of an amplifier circuit is decreased, what is the effect on the gain?
Last Answer : The gain decreases.
Description : In the basic transistor amplifier discussed earlier, what is the relationship between the polarity of the input and output signals?
Last Answer : The signals are opposite in polarity or 180 degrees out of phase with each other.
Description : The input and output signals of a JFET amplifier have what phase relationship?
Last Answer : They are 180 degrees out of phase.
Description : In the illustrated circuit, what is the phase relationship of the amplifier output compared to the input? EL-0022 A. 0° in-phase B. 180° out of phase C. phase angle of the input divided by power factor D. unable to determine without the value of the bias voltage
Last Answer : Answer: B
Description : In a circuit such as that shown in figure 3-16, if R1 has a value of 50 ohms and R2 has a value of 250 ohms and the input signal has a value of +10 millivolts, what is the value of the output signal?
Last Answer : 60 millivolts.
Description : In a circuit such as that shown in figure 3-15, if R1 has a value of 100 ohms and R2 has a value of 1 kilohm and the input signal is at a value of + 5 millivolts, what is the value of the output signal?
Last Answer : 50 millivolts.
Description : In a properly functioning circuit, can both the input and output of an inverter be HIGH at the same time?
Last Answer : No.
Description : If the output of a circuit needs to be a complete representation of one-half of the input signal, what class of operation is indicated?
Last Answer : Class B operation.
Description : What components form the input-signal-developing impedance for the amplifier?
Last Answer : C2 and the secondary of T1.
Description : If the input-signal-developing impedance of an amplifier is increased, what is the effect on the gain?
Last Answer : The gain increases.
Description : When compared to the JFET, what is the input impedance of the MOSFET?
Last Answer : The MOSFET has a higher input impedance.
Description : If the rf amplifier discussed has an 80 milliwatt input, what would be the maximum output?
Last Answer : 800 watts.
Description : Operational amplifiers, used primarily in analog circuits, are characterized by ____________. A. high input impedance, high gain and low output impedance B. high input impedance, high gain and high output ... gain and high output impedance D. low input impedance, high gain and low output impedance
Last Answer : Answer: A
Description : Characteristics impedance of a transmission line is the impedance measured at the ___________ when its length is infinite. A. input B. shorted end of the line C. output D. midsection
Last Answer : A. input
Description : Non-inverting amplifier circuits have _______ (a) Very high input impedance (b) very low input impedance (c) low output impedance (d) none of above
Last Answer : (a) Very high input impedance
Description : A linear network has a current input 4cos(ω t + 20º)A and a voltage output 10 cos(ωt +110º) V. Determine the associated impedance.
Last Answer : Solution
Description : Compare BJT common base configuration with common collector configuration on the basis of (i) Current gain (ii) Voltage gain (iii) Input impedance (iv) Output impedance
Last Answer : Parameter Common Base Common Collector Current gain Low (About 1) High (1+β) Voltage gain High 1 Input impedance Low High Output impedance High Low
Description : When replacing a power transistor fitted with a heat sink in a circuit, a coating of silicone grease is applied between the transistor case and the heat sink. This is done to ____________. A. lubricate ... the heat sink C. aid in the removal of the heat sink D. provide maximum heat transfer
Last Answer : Answer: D
Description : Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator
Last Answer : D. To prevent re-radiation of the local oscillator
Description : One ofthe followingis not a reason forthe use of anantenna coupler: a. To make the antenna look resistive b. To provide the output amplifier with the correct load impedance c. To discriminate against harmonics d. To prevent reradiation of the local oscillator
Last Answer : d. To prevent reradiation of the local oscillator
Description : In a series-RLC circuit, what is the condition of the circuit if there is high impedance, low current, and low reactance voltages
Last Answer : Nonresonant (circuit is either above or below resonance)
Description : What is the difference between calculating impedance in a series ac circuit and in a parallel ac circuit?
Last Answer : In a series circuit impedance is calculated from the values of resistance and reactance. In a parallel circuit, the values of resistive current and reactive current must be used to calculate total impedance.
Description : What type of impedance does the tank circuit have above resonance?
Last Answer : Inductive.
Description : Which type of optical splitter (Y-coupler or T-coupler) splits only a small amount of power from the input fiber to one of the output fibers?
Last Answer : T-coupler
Description : A negative feedback loop returning a voltage to the input raised the input impedance and making the circuit a better
Last Answer : A negative feedback loop returning a voltage to the input raised the input impedance and making the circuit a better voltage sensor
Description : The magnitude of the open-circuit and short circuit input impedance of a transmission line are 100 ohm and 25 ohm respectively. The characteristic impedance of line is: (1) 25 ohm (2) 50 ohm (3) 75 ohm (4) 100 ohm
Last Answer : The magnitude of the open-circuit and short circuit input impedance of a transmission line are 100 ohm and 25 ohm respectively. The characteristic impedance of line is 25 ohm.
Description : The purpose of a short circuit forcing module (short time trip) installed in a branch line is to provide ____________. A. high speed clearance of low impedance short circuits in the branch B. ... C. isolation of short circuits by selective tripping of branch circuit breakers D. all of the above
Description : To provide its unique characteristics to analog circuits, the operational amplifier is made up of a/an ______________. A. voltage amp, current amp and output amp B. input amp, power amp and output amp C. scaling amp, power amp and voltage amp D. differential amp, voltage amp and output amp
Description : What happens to output when a tri-state circuit is selected for high impedance.
Last Answer : Output is disconnected from rest of the circuits by internal circuitry.
Description : Which portion of a sine-wave input is retained in the output of a series-negative limiter?
Last Answer : Positive.
Description : Which portion of a sine-wave input is retained in the output of a series-positive limiter?
Last Answer : Negative.
Description : What would be the output of a negative clamper with a bias potential of −5 volts and an input voltage swing from +50 to −50 volts?
Last Answer : -5 volts.
Description : Which transistor configuration provides a phase reversal between the input and output signals?
Last Answer : Common emitter.
Description : A two-input X-OR gate will produce a HIGH output when the inputs are at what logic levels?
Last Answer : . One or the other of the inputs must be HIGH, but not both at the same time.
Description : select the correct response from the choices given in the parentheses. Q-20. In a closed-loop configuration the output signal is determined by (the input signal, the feedback signal, both).
Last Answer : Both the input signal and the feedback signal.
Description : If If the input signals are 180 degrees out of phase with each other and a combined output is taken between the two output terminals, what will the amplitude of the combined output signal be?
Last Answer : 200 millivolts.
Description : If the input signals are 180 degrees out of phase with each other, what will be the peak-to-peak amplitude of the output signals?
Last Answer : Each output signal will be 100 millivolts.
Description : If the input signals are in phase, what will be the peak-to peak amplitude of the output signals?
Last Answer : 0 volts (the input signals will "cancel out").
Description : If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?
Last Answer : 200 millivolts. A-18. a. Differential amplifier
Description : If the differential amplifier is configured with a single input and differential outputs, what will the output signals be?
Last Answer : Each output will be a sine wave with a peak-to-peak amplitude of 100 millivolts. The output signals will be 180 degrees out of phase with each other.
Description : If the two input signals to a difference amplifier are equal in amplitude but neither in phase nor 180 degrees out of phase, what will the output signal be?
Last Answer : . A different shape than the input signals but larger in amplitude.
Description : If only one input signal is used with a difference amplifier, what will the output signal be?
Last Answer : Equal in shape and frequency to the input signal; larger in amplitude than the input signal; half as large in amplitude as when two input signals were used that were 180 degrees out of phase.
Description : If the two input signals to a difference amplifier are equal in amplitude and 180 degrees out of phase, what will the output signal be?
Last Answer : Equal in shape and frequency to each input signal and larger in amplitude by two times than
Description : . If the two input signals of a difference amplifier are in phase and equal in amplitude, what will the output signal be?
Last Answer : No output (the signals will "cancel out").
Description : What two transistor amplifier configurations are combined in the single-transistor, two-input, single-output difference amplifier?
Last Answer : Common emitter (CE) and common base (CB)
Description : When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease (which one) in the resistance of the regulating device.
Last Answer : An increase.
Description : When the input and output wipers of a balanced potentiometer are in the same angular position, what is the value of the error voltage?
Last Answer : Zero.