One ofthe followingis not a reason forthe use of anantenna coupler: a. To make the antenna look resistive b. To provide the output amplifier with the correct load impedance c. To discriminate against harmonics d. To prevent reradiation of the local oscillator

One ofthe followingis not a reason forthe use of anantenna coupler:
a. To make the antenna look resistive
b. To provide the output amplifier with the correct load impedance c. To discriminate against harmonics
d. To prevent reradiation of the local oscillator
by

1 Answer

Answer :

d. To prevent reradiation of the local oscillator
by

Related questions

Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Description : Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Last Answer : D. To prevent re-radiation of the local oscillator

One ofthe followingis veryuseful as amultibandHFreceivingantenna.Thisisthe: a. conical horn b. folded dipole c. log periodic d. square loop

Description : One ofthe followingis veryuseful as amultibandHFreceivingantenna.Thisisthe: a. conical horn b. folded dipole c. log periodic d. square loop

Last Answer : c. log periodic

The standard reference antenna forthe directive gain isthe a. infinitesimal dipole b. isotropic antenna c. elementary doublet d. half-wave dipole

Description : The standard reference antenna forthe directive gain isthe a. infinitesimal dipole b. isotropic antenna c. elementary doublet d. half-wave dipole

Last Answer : b. isotropic antenna

Non-inverting amplifier circuits have _______ (a) Very high input impedance (b) very low input impedance (c) low output impedance (d) none of above

Description : Non-inverting amplifier circuits have _______ (a) Very high input impedance (b) very low input impedance (c) low output impedance (d) none of above

Last Answer : (a) Very high input impedance

Indicatewhich one ofthe followingreasonsforthe use of a groundscreenwith antennasisfalse: a. Impossibility of a good ground connection b. Provision of an earth for the antenna c.Protectionofpersonnelworkingunderneath d. Improvement of the radiation pattern of the antenna

Description : Indicatewhich one ofthe followingreasonsforthe use of a groundscreenwith antennasisfalse: a. Impossibility of a good ground connection b. Provision of an earth for the antenna c.Protectionofpersonnelworkingunderneath d. Improvement of the radiation pattern of the antenna

Last Answer : c.Protectionofpersonnelworkingunderneath

Indicatewhich ofthe followingreasonsfor usinga counterpoisewith antenna isfalse: a. Impossibility of a good ground connection b.Protectionofpersonnelworkingunderground c. Provision of an earth for the antenna d. Rockiness of the ground

Description : Indicatewhich ofthe followingreasonsfor usinga counterpoisewith antenna isfalse: a. Impossibility of a good ground connection b.Protectionofpersonnelworkingunderground c. Provision of an earth for the antenna d. Rockiness of the ground

Last Answer : b.Protectionofpersonnelworkingunderground

One ofthe followingconsistsof nonresonant antennas: a.The rhombic antenna b. The folded dipole c. The end-fire array d. The broadside array

Description : One ofthe followingconsistsof nonresonant antennas: a.The rhombic antenna b. The folded dipole c. The end-fire array d. The broadside array

Last Answer : a.The rhombic antenna

Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Description : Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Last Answer : C. resistive load at the resonant frequency

Anantenna thatis currentlypolarized usthe a. helical b. small circular loop c. parabolic reflector d. Yagi-Uda

Description : Anantenna thatis currentlypolarized usthe a. helical b. small circular loop c. parabolic reflector d. Yagi-Uda

Last Answer : a. helical

What consists the front-end circuit of a VHF TV superheterodyne receiver? A. Mixer, RF amplifier and AFC? B. RF amplifier, Band pass filter and mixer C. Local oscillator, mixer and RF amplifier D. Local oscillator, AGC and antenna

Description : What consists the front-end circuit of a VHF TV superheterodyne receiver? A. Mixer, RF amplifier and AFC? B. RF amplifier, Band pass filter and mixer C. Local oscillator, mixer and RF amplifier D. Local oscillator, AGC and antenna

Last Answer : C. Local oscillator, mixer and RF amplifier

Refers to one of the front end circuit of a VHF TV superheterodyne receiver which is usually a separate circuit coupled to the mixer. A. Antenna feed B. AGC C. RF amplifier D. Local oscillator

Description : Refers to one of the front end circuit of a VHF TV superheterodyne receiver which is usually a separate circuit coupled to the mixer. A. Antenna feed B. AGC C. RF amplifier D. Local oscillator

Last Answer : D. Local oscillator

P-N junction is (A) a rectifier. (B) an amplifier. (C) an Oscillator. (D) a Coupler.

Description : P-N junction is (A) a rectifier. (B) an amplifier. (C) an Oscillator. (D) a Coupler.

Last Answer : (A) a rectifier.

Distancesnearthe skip distance should beused forthe sky-wave propagation a. to avoid tilting b.topreventsky-wave andupper rayinterference c. to avoid the Faraday effect d. so as nor to exceed the critical frequency

Description : Distancesnearthe skip distance should beused forthe sky-wave propagation a. to avoid tilting b.topreventsky-wave andupper rayinterference c. to avoid the Faraday effect d. so as nor to exceed the critical frequency

Last Answer : b.topreventsky-wave andupper rayinterference

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

Which ofthe followingcableswill have the highestlaunch power capability? a. 50/125/0.2 b. 85/125/0.275 c. 62.5/125/0.275 d. 100/140/0.3

Description : Which ofthe followingcableswill have the highestlaunch power capability? a. 50/125/0.2 b. 85/125/0.275 c. 62.5/125/0.275 d. 100/140/0.3

Last Answer : d. 100/140/0.3

Indicatewhich ofthe followingfrequencies cannotbe used forreliablebeyond-the-horizon terrestrial communicationswithoutrepeaters: a. 20 kHz b. 15 MHz c. 900 MHz d. 12GHz

Description : Indicatewhich ofthe followingfrequencies cannotbe used forreliablebeyond-the-horizon terrestrial communicationswithoutrepeaters: a. 20 kHz b. 15 MHz c. 900 MHz d. 12GHz

Last Answer : d. 12GHz

Indicatewhich one ofthe followingterms appliestotroposcatter propagation: a. SIDs b.Fading c. Atmospheric storms d. Faraday rotation

Description : Indicatewhich one ofthe followingterms appliestotroposcatter propagation: a. SIDs b.Fading c. Atmospheric storms d. Faraday rotation

Last Answer : b.Fading

Themaindisadvantage ofthe two-hole directional coupleris a. low directional coupling b. poor directivity c. high SWR d.narrowbandwidth

Description : Themaindisadvantage ofthe two-hole directional coupleris a. low directional coupling b. poor directivity c. high SWR d.narrowbandwidth

Last Answer : d.narrowbandwidth

The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance C. reducing the input power to below its critical level. D. an impedance mismatch between the load and the line.

Description : The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance ... input power to below its critical level. D. an impedance mismatch between the load and the line.

Last Answer : D. an impedance mismatch between the load and the line.

A waveguide may also be terminated in a resistive load that is matched to the characteristic impedance of the waveguide. The resistive load is most often called a _____

Description : A waveguide may also be terminated in a resistive load that is matched to the characteristic impedance of the waveguide. The resistive load is most often called a _____

Last Answer : Dummy resistor

To couple a coaxialline toa parallel-wire line,itisbesttouse a a. slotted line b.balun c. directional coupler d. quarter-wave transformer

Description : To couple a coaxialline toa parallel-wire line,itisbesttouse a a. slotted line b.balun c. directional coupler d. quarter-wave transformer

Last Answer : b.balun

Fortransmission-line loadmatchingover a range offrequencies,itisbesttouse a a. balun b. broadband directional coupler c. double stub d. single stub of adjustable position

Description : Fortransmission-line loadmatchingover a range offrequencies,itisbesttouse a a. balun b. broadband directional coupler c. double stub d. single stub of adjustable position

Last Answer : c. double stub

One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency oscillation. A. Heating and expansion of oscillator coil B. DC and RF ac heating of resistors which cause change in values C. Heating of capacitor in the oscillatorD. Loose connections in the oscillator, amplifier, or antenna circuits.

Description : One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency ... capacitor in the oscillator D. Loose connections in the oscillator, amplifier, or antenna circuits.

Last Answer : D. Loose connections in the oscillator, amplifier, or antenna circuits.

Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections B. Power supply voltage changes C. Loose connections in the oscillator, amplifier, or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Description : Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections ... , or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Last Answer : D. DC and RF heating of resistors, causing then to change values.

The circuit which changes input signal at output with phase shift of 1800 is called (a) Amplifier (b) operational amplifier (c) switch (d) inverter

Description : The circuit which changes input signal at output with phase shift of 1800 is called (a) Amplifier (b) operational amplifier (c) switch (d) inverter

Last Answer : (d) inverter

A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, what is the antenna current at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Last Answer : D. 2.0 A

What establishes the receiver bandwidth? A. RF amplifier B. Mixer C. Local oscillator D. IF amplifier

Description : What establishes the receiver bandwidth? A. RF amplifier B. Mixer C. Local oscillator D. IF amplifier

Last Answer : D. IF amplifier

After the IF stages have been aligned, the next stage to align in FM receiver is. A. local oscillator B. limiter stage C. RF amplifier D. mixer stage

Description : After the IF stages have been aligned, the next stage to align in FM receiver is. A. local oscillator B. limiter stage C. RF amplifier D. mixer stage

Last Answer : A. local oscillator

One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the high power output. The purpose of which is to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley

Description : One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the ... to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley

Last Answer : B. MOPA

When measuring a transmitter’s frequency against a suitable standard, the frequency to be measured is taken from the A. oscillator stage B. intermediate amplifier C. buffer stage D. final RF stage

Description : When measuring a transmitter’s frequency against a suitable standard, the frequency to be measured is taken from the A. oscillator stage B. intermediate amplifier C. buffer stage D. final RF stage

Last Answer : D. final RF stage

Zoningis usedwith adielectric antenna inorderto a. reduce the bulk of the lense b. increase the bandwidth of the lens c. increase pin-point focusing d. correct the curvature of the wavefront from a horn that is too short

Description : Zoningis usedwith adielectric antenna inorderto a. reduce the bulk of the lense b. increase the bandwidth of the lens c. increase pin-point focusing d. correct the curvature of the wavefront from a horn that is too short

Last Answer : a. reduce the bulk of the lense

Short-circuited stubs are preferred to open-circuited stubs because thelatter are a. more difficult to make an connect b. made of a transmission line with a different characteristic impedance c. liable to radiate

Description : Short-circuited stubs are preferred to open-circuited stubs because thelatter are a. more difficult to make an connect b. made of a transmission line with a different characteristic impedance c. liable to radiate

Last Answer : c. liable to radiate

10] The main reason for generation of harmonics in a transformer could be A. Fluctuating load B. Poor insulation C. Mechanical vibrations D. Saturation of core

Description : 10] The main reason for generation of harmonics in a transformer could be A. Fluctuating load B. Poor insulation C. Mechanical vibrations D. Saturation of core

Last Answer : D) saturation of core

Impedance inversionmaybe obtainedwith a. a short-circuited stub b. an open-circuited stub c. a quarter-wave line d. a half-wave line

Description : Impedance inversionmaybe obtainedwith a. a short-circuited stub b. an open-circuited stub c. a quarter-wave line d. a half-wave line

Last Answer : c. a quarter-wave line

Indicate the false statement A. The noise generated in a resistance or the resistive component of any impedance is random. B. Random noise power is proportional to the bandwidth over which is measured C. A random voltage across the resistor does not exist D. All formula referring to random noise are applicable only to the value of such noise.

Description : Indicate the false statement A. The noise generated in a resistance or the resistive component of any impedance is random. B. Random noise power is proportional to the bandwidth over which is measured ... exist D. All formula referring to random noise are applicable only to the value of such noise.

Last Answer : C. A random voltage across the resistor does not exist

A single-phase transmission line of impedance j 0.8 ohm supplies a resistive...

Description :  A single-phase transmission line of impedance j 0.8 ohm supplies a resistive load of 500 A at 300 V. The sending end power factor is?

Last Answer :  A single-phase transmission line of impedance j 0.8 ohm supplies a resistive load of 500 A at 300 V. The sending end power factor is 0.6 lagging.

Calculated the noise figure of the amplifier whose Req equals 2518Ω (RT=600Ω) if its driven by a generator whose output impedance is 50Ω. A. 39.4 B. 3.94 C. 394 D. 0.394

Description : Calculated the noise figure of the amplifier whose Req equals 2518Ω (RT=600Ω) if its driven by a generator whose output impedance is 50Ω. A. 39.4 B. 3.94 C. 394 D. 0.394

Last Answer : A. 39.4

If the output impedance of an amplifier circuit is decreased, what is the effect on the gain?

Description : If the output impedance of an amplifier circuit is decreased, what is the effect on the gain?

Last Answer : The gain decreases.

For Cascode amplifier the output impedance becomes

Description : For Cascode amplifier the output impedance becomes 

Last Answer : For Cascode amplifier the output impedance becomes very high

A push pull amplifier balances out A) Odd harmonics B) Even harmonics C) Both odd as well as even harmonics D) Neither odd nor even harmonics.

Description : A push pull amplifier balances out A) Odd harmonics B) Even harmonics C) Both odd as well as even harmonics D) Neither odd nor even harmonics.

Last Answer : A) Odd harmonics

Stacking antenna elements A. increases sensitivity to weak signals B. will suppress odd harmonics C. decrease signal to noise ratio D. increases selectivity

Description : Stacking antenna elements A. increases sensitivity to weak signals B. will suppress odd harmonics C. decrease signal to noise ratio D. increases selectivity

Last Answer : A. increases sensitivity to weak signals

A disadvantage of using a trap antenna. A. It will radiate harmonics B. It can only be used for single-bad operation C. It is too sharply directional at lower frequencies D. It must be neutralized

Description : A disadvantage of using a trap antenna. A. It will radiate harmonics B. It can only be used for single-bad operation C. It is too sharply directional at lower frequencies D. It must be neutralized

Last Answer : A. It will radiate harmonics

Which one is an antenna coupling unit? A. Coupler B. Diplexer C. Lecher wire D. Duplexer

Description : Which one is an antenna coupling unit? A. Coupler B. Diplexer C. Lecher wire D. Duplexer

Last Answer : B. Diplexer

Referred to as a ferrite device that can be used in lieu of a duplexer to isolate a microwave transmitter and receiver when both are connected to the same antenna. A. Isolator B. Circulator C. Coupler D. Diode.

Description : Referred to as a ferrite device that can be used in lieu of a duplexer to isolate a microwave transmitter and receiver when both are connected to the same antenna. A. Isolator B. Circulator C. Coupler D. Diode.

Last Answer : B. Circulator

What is the purpose of an antenna coupler

Description : What is the purpose of an antenna coupler

Last Answer : It matches the impedance of an antenna to that of a transmission line at any desired frequency.

A monopoly firm makes more profit because (a) It has ability to choose among price and output combination ; (b) It can discriminate price; (c) It leave the consumer with no consumer surplus ; (d) it acts as a market leader

Description : A monopoly firm makes more profit because (a) It has ability to choose among price and output combination ; (b) It can discriminate price; (c) It leave the consumer with no consumer surplus ; (d) it acts as a market leader

Last Answer : (a) It has ability to choose among price and output combination ;

What is the speaker driving voltage of an amplifier?

Description : What is the speaker driving voltage of an amplifier?

Last Answer : I have to ask WHY? That said, Speakers and a light bulb are two different types of load, and the the lights will probably fry the output transistor.

The gain G of non-inverting amplifier is (a) G = − R2 R1 (b) G = 1 + R2 R1 (c) G = R2 R1 (d) G = 1 − R2 R1

Description : The gain G of non-inverting amplifier is (a) G = − R2 R1 (b) G = 1 + R2 R1 (c) G = R2

Last Answer : (b) G = 1 + R2 R1

The operational amplifier is _______ (a) High gain amplifier (b) high power amplifier (c)high resistance amplifier (d)low resistance amplifier

Description : The operational amplifier is _______ (a) High gain amplifier (b) high power amplifier (c)high resistance amplifier (d)low resistance amplifier

Last Answer : a) High gain amplifier

SI unit of gain of amplifier is (a) Volt (b) ampere (c) coulomb (d) dimensionless

Description : SI unit of gain of amplifier is (a) Volt (b) ampere (c) coulomb (d) dimensionless

Last Answer : (d) dimensionless