In a dc-ac 3-phase MOSFET bridge inverter circuit, the switches are marked in a sequence as 1, 2, 3 in the...

In a dc-ac 3-phase MOSFET bridge inverter circuit, the switches are marked in a sequence as 1, 2, 3 in the top-half and 4, 5, 6 in the bottom half of the bridge. The triggering sequence of switches that gives balanced output voltage is

(A) 1, 2, 3, 4, 5, 6 (B) 1, 5, 3, 4, 2, 6

(C) 1, 6, 2, 4, 3, 5 (D) 1, 4, 2, 5, 3, 6
by

1 Answer

Answer :

In a dc-ac 3-phase MOSFET bridge inverter circuit, the switches are marked in a sequence as 1, 2, 3 in the top-half and 4, 5, 6 in the bottom half of the bridge. The triggering sequence of switches that gives balanced output voltage is 1, 6, 2, 4, 3, 5

by

Related questions

In practice, a current source inverter consists of an AC/ DC converter with a large inductance ‘L’ in the output.

Description : In practice, a current source inverter consists of an AC/ DC converter with a large inductance ‘L’ in the output. This inductance maintains a ……… …………through the switching devices over short interval of time. A) constant current B) constant voltage C) constant power D) none of the (A), (B), (C)

Last Answer : In practice, a current source inverter consists of an AC/ DC converter with a large inductance ‘L’ in the output. This inductance maintains a constant current through the switching devices over short interval of time. 

How IGBT convert DC into AC in solar inverter?

Last Answer : Igbt alone cant convert dc to ac. igbt half bridge or full bridge or three phase topology could be used to convert dc to ac. also igbt gates should be driven by microcontroller or pwm/spwm gate driving signals ... e4(-) and g4 c2e1 and c4e3 pins are AC output pins. its name is igbt inverter.

How does a DC to AC inverter work?

Description : How does a DC to AC inverter work?

Last Answer : Start with a switching circuit that supplies the DC with one polarity then reverses the polarity, back and forth. That's done at the target AC frequency. An inverter that's any good will knock ... and will further attempt to smooth the wave to more closely resemble normal AC power from the mains.

A three-phase, 440 V, 50 Hz ac mains fed thyristor bridge is feeding a 440 V dc, 15 kW, 1500 rpm separately

Description : A three-phase, 440 V, 50 Hz ac mains fed thyristor bridge is feeding a 440 V dc, 15 kW, 1500 rpm separately excited dc motor with a ripple free continuous current in the dc link under all operating conditions, Neglecting the ... at half the rated speed is  (A) 0.354 (B) 0.372 (C) 0.90 (D) 0.955

Last Answer : A three-phase, 440 V, 50 Hz ac mains fed thyristor bridge is feeding a 440 V dc, 15 kW, 1500 rpm separately excited dc motor with a ripple free continuous current in the dc link under all operating conditions, Neglecting the losses, the power factor of the ac mains at half the rated speed is 0.354

A single-phase fully controlled thyristor bridge ac-dc converter is operating at a firing angle of 25 and an

Description : A single-phase fully controlled thyristor bridge ac-dc converter is operating at a firing angle of 25o and an overlap angle of 10o with constant dc output current of 20 A. The fundamental power factor (displacement factor) at input ac mains is  (A) 0.78 (B) 0.827 (C) 0.866 (D) 0.9

Last Answer : A single-phase fully controlled thyristor bridge ac-dc converter is operating at a firing angle of 25o and an overlap angle of 10o with constant dc output current of 20 A. The fundamental power factor (displacement factor) at input ac mains is 0.78

What is the main drawback of a single phase half bridge inverter?

Description : What is the main drawback of a single phase half bridge inverter?

Last Answer : It require a 3-wire dc supply.

A three-phase, fully controlled thyristor bridge converter is used as line commutated inverter to feed 50 kW

Description : A three-phase, fully controlled thyristor bridge converter is used as line commutated inverter to feed 50 kW power 420 V dc to a three-phase, 415 V(line), 50 Hz ac mains. Consider dc link current to be constant. The rms current of the thyristor is  (A) 119.05 A (B) 79.37 A (C) 68.73 A (D) 39.68 A

Last Answer : A three-phase, fully controlled thyristor bridge converter is used as line commutated inverter to feed 50 kW power 420 V dc to a three-phase, 415 V(line), 50 Hz ac mains. Consider dc link current to be constant. The rms current of the thyristor is 68.73 A

Explain three phase bridge inverter.

Description : Explain three phase bridge inverter.

Last Answer : Three phase bridge inverter: Three phase bridge inverter converts DC voltage input to three-phase variable frequency variable voltage output. DC voltage source can be a DC source or output of the rectifier. ... in proper sequence. The switch may be thyristor or IGBT etc.

The direction of rotation of an inverter fed 3-phase ac motor is reversed by

Description : The direction of rotation of an inverter fed 3-phase ac motor is reversed by (A) a mechanical reversing switch (B) reversing the input dc link voltage (C) operating the inverter as a rectifier (D) changing the sequence of switching

Last Answer : The direction of rotation of an inverter fed 3-phase ac motor is reversed by changing the sequence of switching

Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback

Description : Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback

Last Answer : C) All oscillators generate sine waves

Consider the following statements : 1. The voltage developed across the OFF switches of the half bridge...

Description : Consider the following statements : 1. The voltage developed across the OFF switches of the half bridge converter is the maximum dc link voltage. 2. In the full bridge converter, the voltage across ... bridge converter is half the maximum dc link voltage. Which of the above statements are correct ?

Last Answer : Consider the following statements : 1. The voltage developed across the OFF switches of the half bridge converter is the maximum dc link voltage. 2. In the full bridge converter, the voltage across the primary of ... dc link voltage. Which of the above statements are correct ? 1 and 2 only

The circuit which changes input signal at output with phase shift of 1800 is called (a) Amplifier (b) operational amplifier (c) switch (d) inverter

Description : The circuit which changes input signal at output with phase shift of 1800 is called (a) Amplifier (b) operational amplifier (c) switch (d) inverter

Last Answer : (d) inverter

A large dc motor is required to control the speed of the blower from a 3 -phase ac source. The suitable ac to ...

Description : A large dc motor is required to control the speed of the blower from a 3 -phase ac source. The suitable ac to dc converter is, 3 -phase (a) Fully controlled bridge converter ( ... bridge converter with freewheeling diode (c) Half controlled bridge converter (d) Converter pair in sequence control

Last Answer : a fullu control

Compare AC & DC track circuits on i) Length of circuit ii) Application iii) Effect of stray currents. iv) Maintenance

Description : Compare AC & DC track circuits on i) Length of circuit ii) Application iii) Effect of stray currents. iv) Maintenance

Last Answer : Ans: i) Length of circuit - a) AC track circuit is having long length upto 3 to 5 km b) DC track circuit is having short length  ii)Application -a) AC track circuit is used ... ) Maintenance - a) AC track circuit has easier and cheaper maintenance b) DC track circuit has complicated maintenance 

A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input

Description : A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is :

Last Answer : A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is : 200 V

i want to construcy an inverter but don't have a circuit digram

Last Answer : Digital inverter or analog? Actually as you know, a transistor by itself is already an inverter however you can use resistive load inverter for digital circuits by having two mosfets, pmos at the top ... be connected and that connection should have a pulse signal in order to switch the mosfets. 

Benefits of Using a DC Inverter During Road Trips?

Description : Benefits of Using a DC Inverter During Road Trips?

Last Answer : The average person cannot identify a DC inverter simply by looking at one. However, most drivers do know what purpose these small devices serve. These inverters plug into a vehicle's DC outlet and ... should always consider going out and buying one of these little units for their next road trip.

The MIL is illuminated and a battery module deterioration diagnostic trouble code is stored the most like cause is a failed by a) High voltage battery b) High voltage inverter c) Motor/ generator d) DC/ DC converter

Description : The MIL is illuminated and a battery module deterioration diagnostic trouble code is stored the most like cause is a failed by a) High voltage battery b) High voltage inverter c) Motor/ generator d) DC/ DC converter

Last Answer : a) High voltage battery

In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage

Description : In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage

Last Answer : In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage decreases

The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a

Description : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ (A) directly proportional to α and Φ (B) ... proportional to α and inversely proportional to Φ (D) directly proportional to Φ and inversely proportional to α

Last Answer : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ directly proportional to α and inversely proportional to Φ

A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc

Description : A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is (A) 4.5 V (B) 6.75 V (C) 9 V (D) 13.5 V

Last Answer : A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is 9 V

What is the load of an AC inverter on a battery?

Description : What is the load of an AC inverter on a battery?

Last Answer : answer:If this is a new inverter, figure it is only 80% efficient. If you are truly drawing 1100 Watts continuously then the inverter is drawing 1375 Watts. You are feeding it with 12 volts Power = ... gas generator. Sorry for the bad news but the most of the laws of physics are difficult to break.

Which variable frequency drive should I use for a 1.5 ton inverter AC?

Description : Which variable frequency drive should I use for a 1.5 ton inverter AC?

Last Answer : You do not need to use an external variable frequency drive for the said AC. You have mentioned that it is inverter AC. It means the AC is already fitted with a built in ... / compressor depending upon the room condition, external temperature, temperature setting etc. It is little complicated.

Manufacturers claim up to savings on inverter tech AC h. 50% c) 55% i. 60% d) 65%

Description : Manufacturers claim up to savings on inverter tech AC h. 50% c) 55% i. 60% d) 65%

Last Answer : 60%

Inverter technology AC cost further. a) More c) less b) Equal d) all of the above

Description : Inverter technology AC cost further. a) More c) less b) Equal d) all of the above

Last Answer : more

74. Inverter tech AC if usage of AC is more than 1000 hour in a year and per unit cost of electricity is more than rs _________per unit. a) 10 c) 5 b) 7 d) 4

Description : 74. Inverter tech AC if usage of AC is more than 1000 hour in a year and per unit cost of electricity is more than rs _________per unit. a) 10 c) 5 b) 7 d) 4

Last Answer : 5

In inverter tech AC some manufactures claim up to saving____________. a) 50% c) 60% b) 20% d) 80%

Description : In inverter tech AC some manufactures claim up to saving____________. a) 50% c) 60% b) 20% d) 80%

Last Answer : 60%

In comparison an inverter tech AC being flexible tonnage AC can save more over_________star AC. a) BEE3 c) BEE1 b) BEE5 d) BEE4

Description : In comparison an inverter tech AC being flexible tonnage AC can save more over_________star AC. a) BEE3 c) BEE1 b) BEE5 d) BEE4

Last Answer : BEE5

A solar cell of 350 V is feeding power to an ac supply of 440 V, 50 Hz through a 3-phase fully controlled bridge

Description : A solar cell of 350 V is feeding power to an ac supply of 440 V, 50 Hz through a 3-phase fully controlled bridge converter. A large inductance is connected in the dc circuit to maintain the dc current at 20 A ... thyristor will be reverse biased for a period of  (A) 125o (B) 120o (C) 60o (D) 55o

Last Answer : A solar cell of 350 V is feeding power to an ac supply of 440 V, 50 Hz through a 3-phase fully controlled bridge converter. A large inductance is connected in the dc circuit to maintain the ... the solar cell resistance is 0.5 Ohm ,then each thyristor will be reverse biased for a period of 125o

A 3-phase fully controlled bridge converter with free wheeling diode is fed from 400 V, 50 Hz AC source and

Description : A 3-phase fully controlled bridge converter with free wheeling diode is fed from 400 V, 50 Hz AC source and is operating at a firing angle of 60o. The load current is assumed constant at 10 A due to high load inductance. The input ... 0.552 (C) IDF IPF = = 0.5; 0.478 (D) IDF IPF = = 0.5; 0.318 

Last Answer : A 3-phase fully controlled bridge converter with free wheeling diode is fed from 400 V, 50 Hz AC source and is operating at a firing angle of 60o. The load current is assumed constant at 10 A due to high ... (IDF) and the input power factor (IPF) of the converter will be IDF IPF = = 0.5; 0.478

During 3-phase short circuit on a unloaded alternator, the dc component may be zero in

Description : During 3-phase short circuit on a unloaded alternator, the dc component may be zero in (1) One phase only (2) Any two phases (3) All three phases (4) None of the above 

Last Answer : 1

Handheld phase sequence indicators are useful when ________. A. preparing to parallel alternators B. connecting lighting branch circuits C. troubleshooting DC motors D. connecting shore power lines to the ship

Description : Handheld phase sequence indicators are useful when ________. A. preparing to parallel alternators B. connecting lighting branch circuits C. troubleshooting DC motors D. connecting shore power lines to the ship

Last Answer : Answer: D

Draw neat labeled diagram of single phase AC locomotive showing its various equipments of power circuit and give function of each equipment used in power circuit.

Description : Draw neat labeled diagram of single phase AC locomotive showing its various equipments of power circuit and give function of each equipment used in power circuit.

Last Answer : Functions of equipment: 1) circuit breaker: disconnects the locomotive equipment from the supply in the event of fault in the equipment / loco. 2) On load tap changer, used to control the ... 6) Traction motor: operates as per the required operating characteristics to take on the traction load.

An AC generator panel is fitted with both synchronizing lamps and a synchroscope. When the synchroscope pointer reaches the noon position, one synchronizing light is bright and the other is dark. This means _____________. A. there is a ground on the phase with the dark lamp B. the phase sequence is incorrect C. the phase sequence is correct D. the generator breaker may be closed

Description : An AC generator panel is fitted with both synchronizing lamps and a synchroscope. When the synchroscope pointer reaches the noon position, one synchronizing light is bright and the other is dark. This ... sequence is incorrect C. the phase sequence is correct D. the generator breaker may be closed

Last Answer : Answer: B

The voltage of an operating AC turbogenerator is raised or lowered by adjusting the _____________. A. exciter generator governor controls B. synchronizing switch C. phase sequence switch D. generator field exciter

Description : The voltage of an operating AC turbogenerator is raised or lowered by adjusting the _____________. A. exciter generator governor controls B. synchronizing switch C. phase sequence switch D. generator field exciter

Last Answer : Answer: D

When three-phase AC power is supplied to the device shown in the illustration, the output will be _____________. EL-0063 A. single-phase AC B. split-phase AC C. three-phase DC D. unidirectional DC

Description : When three-phase AC power is supplied to the device shown in the illustration, the output will be _____________. EL-0063 A. single-phase AC B. split-phase AC C. three-phase DC D. unidirectional DC

Last Answer : Answer: D

AC and DC generators are similar in that they _____________. A. both generate alternating voltages B. both rectify the voltage before delivery C. are constructed at the same physical size for the same kilowatt rating D. both supply three-phase power

Description : AC and DC generators are similar in that they _____________. A. both generate alternating voltages B. both rectify the voltage before delivery C. are constructed at the same physical size for the same kilowatt rating D. both supply three-phase power

Last Answer : Answer: A

The output voltage of a three-phase alternator is regulated by the _____________. A. AC voltage to the armature B. AC voltage to the field C. DC voltage to the armature D. DC voltage to the field

Description : The output voltage of a three-phase alternator is regulated by the _____________. A. AC voltage to the armature B. AC voltage to the field C. DC voltage to the armature D. DC voltage to the field

Last Answer : Answer: D

A stepper motor is (A) a dc motor. (B) a single-phase ac motor. (C) a multi-phase motor. (D) a two phase motor.

Description : A stepper motor is (A) a dc motor. (B) a single-phase ac motor. (C) a multi-phase motor. (D) a two phase motor.

Last Answer : Ans: D Stepper motor works on 1-phase-ON or 2-phase –ON modes of operation

The most suitable servomotor for low power applications is (A) a dc series motor. (B) a dc shunt motor. (C) an ac two-phase induction motor. (D) an ac series motor.

Description : The most suitable servomotor for low power applications is (A) a dc series motor. (B) a dc shunt motor. (C) an ac two-phase induction motor. (D) an ac series motor.

Last Answer : (B) a dc shunt motor.

Compare Single phase 25 kV AC and 1500 V DC track electrification.

Description : Compare Single phase 25 kV AC and 1500 V DC track electrification.

Last Answer : Points Single phase 25 kV AC track Electrification 1500 V DC track electrification Supply given to O/H condition 1-ph, 25KV, AC 50 Hz  600/750V-Tromways 1500/3000V urban/suburban ... track distance Less More Applications Main line services Urban and suburban area

When an AC or a DC motor fails to start, the FIRST step in troubleshooting should be to check the ____________. A. motor windings for obvious opens B. motor controller leads for continuity C. fuse or circuit breaker D. motor controller leads for grounds

Description : When an AC or a DC motor fails to start, the FIRST step in troubleshooting should be to check the ____________. A. motor windings for obvious opens B. motor controller leads for continuity C. fuse or circuit breaker D. motor controller leads for grounds

Last Answer : Answer: C

A transformer in an electric circuit serves to ____________. A. generate its own electrical power B. transform electrical energy into mechanical energy C. increase or decrease circuit voltage as required D. convert AC current to DC current

Description : A transformer in an electric circuit serves to ____________. A. generate its own electrical power B. transform electrical energy into mechanical energy C. increase or decrease circuit voltage as required D. convert AC current to DC current

Last Answer : Answer: C

The purpose of the bias winding in figure 'B' shown in the illustration is for ____________. EL-0091 A. changing the direction of current in the control winding B. setting the operating point of the device C. allowing the use of either AC or DC in the load circuit D. changing the direction of current through the load

Description : The purpose of the bias winding in figure 'B' shown in the illustration is for ____________. EL-0091 A. changing the direction of current in the control winding B. setting the operating point of the ... use of either AC or DC in the load circuit D. changing the direction of current through the load

Last Answer : Answer: B

Which section of the circuit shown in the illustration changes AC to DC? EL-0085 A. I B. II C. III D. IV

Description : Which section of the circuit shown in the illustration changes AC to DC? EL-0085 A. I B. II C. III D. IV

Last Answer : Answer: B

The purpose of DC generator brushes is to _____________. A. neutralize armature reaction B. conduct electric current to an outside circuit C. convert DC current to AC current D. provide excitation to a DC generator

Description : The purpose of DC generator brushes is to _____________. A. neutralize armature reaction B. conduct electric current to an outside circuit C. convert DC current to AC current D. provide excitation to a DC generator

Last Answer : Answer: B

When troubleshooting electronic equipment, you should use a high impedance multimeter ________________. A. to prevent excess current flow through the meter that would damage it B. for AC measurements only and a low resistance meter for DC measurements C. whenever a low impedance meter is not available, regardless of the components being tested D. so as not to load down the circuit and obtain erroneous voltage readings

Description : When troubleshooting electronic equipment, you should use a high impedance multimeter ________________. A. to prevent excess current flow through the meter that would damage it B. for AC measurements only ... being tested D. so as not to load down the circuit and obtain erroneous voltage readings

Last Answer : Answer: D

Can we use ac coils in dc circuit?

Description : Can we use ac coils in dc circuit? 

Last Answer : Yes with economy resistor in series.