In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage

In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage
by

1 Answer

Answer :

In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage decreases

by

Related questions

The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a

Description : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ (A) directly proportional to α and Φ (B) ... proportional to α and inversely proportional to Φ (D) directly proportional to Φ and inversely proportional to α

Last Answer : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ directly proportional to α and inversely proportional to Φ

The ripple factor of a bridge rectifier is

Description : The ripple factor of a bridge rectifier is  1.0.48 2.0.812 3. 1.11 4. 1.21 

Last Answer : The ripple factor of a bridge rectifier is 0.48

In d.c. choppers, for periodic time T, the output voltage can be controlled by frequency modulation by varying

Description : In d.c. choppers, for periodic time T, the output voltage can be controlled by frequency modulation by varying

Last Answer : In d.c. choppers, for periodic time T, the output voltage can be controlled by frequency modulation by varying T, keeping ton constant

The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc

Description : The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc voltage with resistive load and without filter will be • 12.1 volt • 1.21 volt • 0.482 volt • 4.82 volt

Last Answer : The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc voltage with resistive load and without filter will be 12.1 volt

Chopper controlled DC motor

Description : Chopper controlled DC motor

Last Answer : Chopper controlled DC motor

A single-phase half-controlled rectifier is driving a separately excited dc motor. The dc motor has a back emf

Description : A single-phase half-controlled rectifier is driving a separately excited dc motor. The dc motor has a back emf constant of 0.5 V/rpm. The armature current is 5 A without any ripple. The armature resistance is 2 Ohm. The ... of the motor will be  (A) 339 rpm (B) 359 rpm (C) 366 rpm (D) 386 rpm

Last Answer : 359

Which of the following statements represents an application of a silicon controlled rectifier? A. To provide DC power for a main propulsion motor. B. For use as a voltage reference diode. C. For sensing flame in an automated burner. D. To eliminate power supply hum.

Description : Which of the following statements represents an application of a silicon controlled rectifier? A. To provide DC power for a main propulsion motor. B. For use as a voltage reference diode. C. For sensing flame in an automated burner. D. To eliminate power supply hum.

Last Answer : Answer: A

The illustrated device is a _______. EL-0064 A. full wave bridge rectifier B. half wave bridge rectifier C. solid state voltage regulator D. direct current (DC) filter

Description : The illustrated device is a _______. EL-0064 A. full wave bridge rectifier B. half wave bridge rectifier C. solid state voltage regulator D. direct current (DC) filter

Last Answer : Answer: A

A single phase, half-wave, controlled rectifier has 400 sin (314 t) as the input voltage and R as the load...

Description : A single phase, half-wave, controlled rectifier has 400 sin (314 t) as the input voltage and R as the load. For a firing angle of 60° for the SCR, the average output voltage is   (a) 240/π (b) 400/π (c) 300/π (d) 200/π 

Last Answer : C

The output from a full wave rectifier is (a) A pulsating uni-directional current (b) A DC voltage (c) Zero (d) An AC voltage

Description : The output from a full wave rectifier is (a) A pulsating uni-directional current (b) A DC voltage (c) Zero (d) An AC voltage

Last Answer : a) A pulsating uni-directional current

An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Description : An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Last Answer : Solution:

A single-phase fully controlled thyristor bridge ac-dc converter is operating at a firing angle of 25 and an

Description : A single-phase fully controlled thyristor bridge ac-dc converter is operating at a firing angle of 25o and an overlap angle of 10o with constant dc output current of 20 A. The fundamental power factor (displacement factor) at input ac mains is  (A) 0.78 (B) 0.827 (C) 0.866 (D) 0.9

Last Answer : A single-phase fully controlled thyristor bridge ac-dc converter is operating at a firing angle of 25o and an overlap angle of 10o with constant dc output current of 20 A. The fundamental power factor (displacement factor) at input ac mains is 0.78

A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc

Description : A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is (A) 4.5 V (B) 6.75 V (C) 9 V (D) 13.5 V

Last Answer : A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is 9 V

In a 3-phase half-wave rectifier, if per phase input is 200 V, then the average output voltage is

Description : In a 3-phase half-wave rectifier, if per phase input is 200 V, then the average output voltage is   (a) 233.91 V (b) 116.95V (c) 202.56 V (d) 101.28V 

Last Answer : a

A silicon controlled rectifier (SCR) is a solid state device used to change ________________. A. DC to AC and control relatively low load current B. AC to DC and control relatively high load current C. DC to AC and control relatively high load current D. AC to DC and control relatively low load current

Description : A silicon controlled rectifier (SCR) is a solid state device used to change ________________. A. DC to AC and control relatively low load current B. AC to DC and control relatively high load ... to AC and control relatively high load current D. AC to DC and control relatively low load current

Last Answer : Answer: B

The dc current through each diode in a bridge rectifier equals : -

Description : The dc current through each diode in a bridge rectifier equals : - a) the load current b) half the dc load current c) twice the dc load current d) one-fourth the dc load current

Last Answer : The dc current through each diode in a bridge rectifier equals : - the load current

The voltage output of an AC generator is accurately controlled by _____________. A. changing the sensitivity of the prime mover to large changes in voltage B. varying the reluctance of the air gap C. varying the DC exciter voltage D. shorting out part of the armature windings

Description : The voltage output of an AC generator is accurately controlled by _____________. A. changing the sensitivity of the prime mover to large changes in voltage B. varying the reluctance of the air gap C. varying the DC exciter voltage D. shorting out part of the armature windings

Last Answer : Answer: C

In dc choppers for chopping period T, the output voltage can be controlled by FM by varying

Description : In dc choppers for chopping period T, the output voltage can be controlled by FM by varying   (A) T keeping Ton constant (B) Ton keeping T constant (C) Toff keeping T constant (D) None of the above

Last Answer : In dc choppers for chopping period T, the output voltage can be controlled by FM by varying T keeping Ton constant

The output voltage of a three-phase alternator is regulated by the _____________. A. AC voltage to the armature B. AC voltage to the field C. DC voltage to the armature D. DC voltage to the field

Description : The output voltage of a three-phase alternator is regulated by the _____________. A. AC voltage to the armature B. AC voltage to the field C. DC voltage to the armature D. DC voltage to the field

Last Answer : Answer: D

Why we are using the bridge rectifier in most of the circuits instead of full wave rectifier eventhough the output of both are same?

Description : Why we are using the bridge rectifier in most of the circuits instead of full wave rectifier eventhough the output of both are same?

Last Answer : Ans-In bridge type (FWR) rectifiers center tapping transformer are not required so small transformers are used and we will get twice of the out put voltage that of the center tapped FWR.

Explain the operation of a full wave bridge rectifier with π filter using a neat diagram. Draw input and output waveforms.

Description : Explain the operation of a full wave bridge rectifier with π filter using a neat diagram. Draw input and output waveforms.

Last Answer : During positive half-cycle of input, the secondary voltage VAB is positive, so diodes D1 and D2 forward biased and D3 and D4 reverse biased. The load current flows from terminal A ... smooth DC voltage appears across the load. The input and output waveforms are shown in the figure.

Draw & describe working of bridge rectifier with its input output waveforms

Description : Draw & describe working of bridge rectifier with its input output waveforms

Last Answer : Four diodes are used. a)In positive half cycle Diodes D1 & D3 becomes forward biased they will conduct & current flows at that time D2 and D4 are reverse biased they will not ... at that time D1 and D3 are reverse biased they will not conduct. we get full cycle rectification.

Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier

Description : Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier 

Last Answer : Rectifier - This circuit convert AC signal into DC.

Draw the circuit diagram of bridge rectifier with π filter. Draw its input and output waveform.

Description : Draw the circuit diagram of bridge rectifier with π filter. Draw its input and output waveform. 

Last Answer : Circuit diagram of bridge rectifier with π filter : Input and output waveform:

The input frequency of a bridge rectifier is 50 its output frequency will be

Description : The input frequency of a bridge rectifier is 50 its output frequency will be  1. 25 Hz 2.50 Hz 3.75 Hz 4. 100 Hz

Last Answer : The input frequency of a bridge rectifier is 50 its output frequency will be 100 Hz

Slip-Energy Recovery (SER) scheme for three phase Induction Motor

Description : Slip-Energy Recovery (SER) scheme for three phase Induction Motor

Last Answer : Slip-Energy Recovery (SER) scheme for three phase Induction Motor

A step-down chopper, fed from a 120 volt DC source, operates a DC motor whose armature e.m.f. and

Description : A step-down chopper, fed from a 120 volt DC source, operates a DC motor whose armature e.m.f. and armature resistance are 100 volt and 0.5Ω respectively. With the magnitude control ratio 0.6, the quadrant of operation DC motor is  (a) First (b) Second (c) Third (d) Fourth

Last Answer : A step-down chopper, fed from a 120 volt DC source, operates a DC motor whose armature e.m.f. and armature resistance are 100 volt and 0.5Ω respectively. With the magnitude control ratio 0.6, the quadrant of operation DC motor is First

A DC chopper is used for regenerative braking of a separately excited DC motor. The DC supply

Description : A DC chopper is used for regenerative braking of a separately excited DC motor. The DC supply voltage is 400V. The armature current during regenerative braking is kept constant at 300 A with negligible ripple. For a duty cycle of 60% ... to the DC supply is  (a) 78 kW (b) 58 kW (c) 38 kW (d) 48 kW

Last Answer : 48

What is meant by phase controlled rectifier?

Description : What is meant by phase controlled rectifier?

Last Answer : It converts fixed ac voltage into variable dc voltage.

What is delay angle or what is firing angle of phase controlled rectifier?

Description : What is delay angle or what is firing angle of phase controlled rectifier?

Last Answer : The delay angle is the angle at which thyristors are triggered after zero crossing. After zero crossing of supply voltage, one pair of thyristors is forward biased. After delay angle(α) these SCRs are triggered.

Single-phase mid-point controlled rectifier with RL load

Description : Single-phase mid-point controlled rectifier with RL load

Last Answer : Single-phase mid-point controlled rectifier with RL load : The circuit configuration of single-phase midpoint controlled rectifier is shown in the figure. During positive half-cycle of ... some part of next positive half-cycle of voltage with reversed polarity can appear across load.

Single-phase Midpoint controlled rectifier with Resistive load

Description : Single-phase Midpoint controlled rectifier with Resistive load

Last Answer : Single-phase Midpoint controlled rectifier with Resistive load:  1) During positive half cycle of AC supply, a is positive with respect to b , this makes T1 forward biased and T2 is reverse ... voltage reverses the polarity and T2 is turned off. The operation is as shown in waveforms.

When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a

Description : When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a load is 30°, the displacement power factor of the rectifier is

Last Answer : When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a load is 30°, the displacement power factor of the rectifier is √3/2

A single-phase full-bridge diode rectifier delivers a load current of 10A, which is ripple free.

Description : A single-phase full-bridge diode rectifier delivers a load current of 10A, which is ripple free. Average and rms values of diode currents are respectively   (a) 10A, 7.07A (b) 5A, 10A (c) 5A, 7.07A (d) 7.07A, 5A

Last Answer : A single-phase full-bridge diode rectifier delivers a load current of 10A, which is ripple free. Average and rms values of diode currents are respectively 5A, 7.07A

A three-phase, fully controlled thyristor bridge converter is used as line commutated inverter to feed 50 kW

Description : A three-phase, fully controlled thyristor bridge converter is used as line commutated inverter to feed 50 kW power 420 V dc to a three-phase, 415 V(line), 50 Hz ac mains. Consider dc link current to be constant. The rms current of the thyristor is  (A) 119.05 A (B) 79.37 A (C) 68.73 A (D) 39.68 A

Last Answer : A three-phase, fully controlled thyristor bridge converter is used as line commutated inverter to feed 50 kW power 420 V dc to a three-phase, 415 V(line), 50 Hz ac mains. Consider dc link current to be constant. The rms current of the thyristor is 68.73 A

A three phase fully controlled bridge converter is feeding a load drawing a constant and ripple free load

Description : A three phase fully controlled bridge converter is feeding a load drawing a constant and ripple free load current of 10 A at a firing angle of 30o. The approximate Total harmonic Distortion (%THD) and the rms value of fundamental component ... (B) 31% and 7.8 A (C) 66% and 6.8 A (D) 66% and 7.8 A

Last Answer : A three phase fully controlled bridge converter is feeding a load drawing a constant and ripple free load current of 10 A at a firing angle of 30o. The approximate Total harmonic Distortion (%THD) and the rms value of fundamental component of input current will respectively be 31% and 7.8 A

A three-phase, 440 V, 50 Hz ac mains fed thyristor bridge is feeding a 440 V dc, 15 kW, 1500 rpm separately

Description : A three-phase, 440 V, 50 Hz ac mains fed thyristor bridge is feeding a 440 V dc, 15 kW, 1500 rpm separately excited dc motor with a ripple free continuous current in the dc link under all operating conditions, Neglecting the ... at half the rated speed is  (A) 0.354 (B) 0.372 (C) 0.90 (D) 0.955

Last Answer : A three-phase, 440 V, 50 Hz ac mains fed thyristor bridge is feeding a 440 V dc, 15 kW, 1500 rpm separately excited dc motor with a ripple free continuous current in the dc link under all operating conditions, Neglecting the losses, the power factor of the ac mains at half the rated speed is 0.354

The direction of rotation of an inverter fed 3-phase ac motor is reversed by

Description : The direction of rotation of an inverter fed 3-phase ac motor is reversed by (A) a mechanical reversing switch (B) reversing the input dc link voltage (C) operating the inverter as a rectifier (D) changing the sequence of switching

Last Answer : The direction of rotation of an inverter fed 3-phase ac motor is reversed by changing the sequence of switching

A moving coil meter has a resistance of 3 Ω and gives full scale deflection with 30 mA. To measure voltage up

Description : A moving coil meter has a resistance of 3 Ω and gives full scale deflection with 30 mA. To measure voltage up to 300 V, the external resistance to be connected in series with the instrument is (A) 9997 Ω (B) 10000 Ω (C) 997 Ω (D) 10003 Ω

Last Answer : A moving coil meter has a resistance of 3 Ω and gives full scale deflection with 30 mA. To measure voltage up to 300 V, the external resistance to be connected in series with the instrument is 9997 Ω

When the peak output voltage is 100 V the PIV for each diode in a center-tapped full-wave rectifier is (neglecting the diode drop)?

Description : When the peak output voltage is 100 V the PIV for each diode in a center-tapped full-wave rectifier is (neglecting the diode drop)?

Last Answer : Feel Free to Answer

What effect does an open diode have on the output voltage of a half wave rectifier and on a full wave rectifier?

Description : What effect does an open diode have on the output voltage of a half wave rectifier and on a full wave rectifier?

Last Answer : An open diode will result in no output from a half waverectifier, and an open diode will cut the output of a full waverectifier in half.

What is the average voltage (Eavg) Output of a full-wave rectifier with an output of 100 volts peak?

Description : What is the average voltage (Eavg) Output of a full-wave rectifier with an output of 100 volts peak?

Last Answer : 63.7 volts.

If the output of a half-wave rectifier is 50-volts peak, what is the average voltage

Description : If the output of a half-wave rectifier is 50-volts peak, what is the average voltage

Last Answer : 15.9 volts.

What is the average voltage (Eavg) output of a full-wave rectifier that has an output of 100 volts peak?

Description : What is the average voltage (Eavg) output of a full-wave rectifier that has an output of 100 volts peak?

Last Answer : 63.6 volts.

Give the operation of single phase full wave bridge controlled converter with RL load with a neat diagram. Also draw its waveform.

Description : Give the operation of single phase full wave bridge controlled converter with RL load with a neat diagram. Also draw its waveform.

Last Answer : Single phase fully control bridge converter with RL load: 1. During positive half cycle of input voltage, T1 and T2 are forward biased and during negative half cycle, T3 and T4 are forward biased. Therefore, T1-T2 ... cycle till the firing of next pair of SCRs as shown in the waveform.

A solar cell of 350 V is feeding power to an ac supply of 440 V, 50 Hz through a 3-phase fully controlled bridge

Description : A solar cell of 350 V is feeding power to an ac supply of 440 V, 50 Hz through a 3-phase fully controlled bridge converter. A large inductance is connected in the dc circuit to maintain the dc current at 20 A ... thyristor will be reverse biased for a period of  (A) 125o (B) 120o (C) 60o (D) 55o

Last Answer : A solar cell of 350 V is feeding power to an ac supply of 440 V, 50 Hz through a 3-phase fully controlled bridge converter. A large inductance is connected in the dc circuit to maintain the ... the solar cell resistance is 0.5 Ohm ,then each thyristor will be reverse biased for a period of 125o

A 3-phase fully controlled bridge converter with free wheeling diode is fed from 400 V, 50 Hz AC source and

Description : A 3-phase fully controlled bridge converter with free wheeling diode is fed from 400 V, 50 Hz AC source and is operating at a firing angle of 60o. The load current is assumed constant at 10 A due to high load inductance. The input ... 0.552 (C) IDF IPF = = 0.5; 0.478 (D) IDF IPF = = 0.5; 0.318 

Last Answer : A 3-phase fully controlled bridge converter with free wheeling diode is fed from 400 V, 50 Hz AC source and is operating at a firing angle of 60o. The load current is assumed constant at 10 A due to high ... (IDF) and the input power factor (IPF) of the converter will be IDF IPF = = 0.5; 0.478

A single phase full-wave half-controlled bridge converter feeds an inductive load. The two SCRs in the

Description : A single phase full-wave half-controlled bridge converter feeds an inductive load. The two SCRs in the converter are connected to a common DC bus. The converter has to have a freewheeling diode.  (A) ... to one of the SCRs is missed, it will subsequently cause a high load current in the other SCR.

Last Answer : A single phase full-wave half-controlled bridge converter feeds an inductive load. The two SCRs in the converter are connected to a common DC bus. The converter has to have a freewheeling diode. because the converter does not provide for free-wheeling for high values of triggering angles

A single phase fully controlled bridge converter supplies a load drawing constant and ripple free load current,

Description : A single phase fully controlled bridge converter supplies a load drawing constant and ripple free load current, if the triggering angle is 30o, the input power factor will be  (A) 0.65 (B) 0.78 (C) 0.85 (D) 0.866

Last Answer : A single phase fully controlled bridge converter supplies a load drawing constant and ripple free load current, if the triggering angle is 30o, the input power factor will be 0.78

In a single-phase full converter, the number of SCRs conducting during overlap is

Description : In a single-phase full converter, the number of SCRs conducting during overlap is   (a) 1 (b) 2 (c) 3 (d) 4 

Last Answer : 4