An FET is a better chopper than a BJT because it has

An FET is a better chopper than a BJT because it has

(A) lower offset voltage (B) higher series ON resistance

(C) lower input current (D) higher input impedance
by

1 Answer

Answer :

An FET is a better chopper than a BJT because it has lower offset voltage

by

Related questions

Is the input impedance of MOSFET more than BJT and FET?

Description : Is the input impedance of MOSFET more than BJT and FET?

Last Answer : Yes, the input impedance of MOSFET more than BJT and FET.

Compare BJT with FET

Description : Compare BJT with FET

Last Answer : FET BJT It is unipolar device i.e. current in the device is carried either by electrons or holes It is bipolar device i.e. current in the device is carried either by ... from minority- carrier storage effects & therefore has lower switching speeds & cut-off frequencies. 

Compare between BJT and FET on the basis of (i) Biolar/Unipolar (ii) Tharmal Runaway (iii) Noise (iv) Applications

Description : Compare between BJT and FET on the basis of (i) Biolar/Unipolar (ii) Tharmal Runaway (iii) Noise (iv) Applications

Last Answer : Parameter BJT FET Bipolar/Unipolar It is bipolar device i.e. current in this device is carried by electrons and holes. It is unipolar device i.e. current ... in oscilloscopes, electronic voltmeters and other measuring and testing equipment because of their high input impedance.

What is the difference between BJT and FET?

Description : What is the difference between BJT and FET?

Last Answer : BJT  is  a  current  opperated   transistor  while  FET   is  a  field   opperated  transistor.

A dc chopper is fed from a constant voltage mains the duty ratio of chopper is progressively increased while

Description : A dc chopper is fed from a constant voltage mains the duty ratio of chopper is progressively increased while the chopper feeds an RL load. The per unit current ripple would  (1) increase progressively  (2 ... 0.5 and then increase  (4) increase to a maximum value at α = 0.5 and then decrease

Last Answer : A dc chopper is fed from a constant voltage mains the duty ratio of chopper is progressively increased while the chopper feeds an RL load. The per unit current ripple would increase to a maximum value at α = 0.5 and then decrease

Can we use triac in multiquadrant chopper?

Last Answer : Yes, we can use triac in the multi-quadrant chopper.

Explain two quadrant chopper.

Description : Explain two-quadrant chopper.........

Last Answer : Two quadrant chopper:  There are two semiconductor controllable switches in the two-quadrant chopper. Two quadrant type A chopper: The figure shows the type A chopper. Both the switch never turn on at ... 2 are turned on then Vo=Vs. When chopper 1 and chopper 2 are off then Vo=-Vs.

In a thyristor D.C. chopper, which type of commutation results in best performance ?

Description : In a thyristor D.C. chopper, which type of commutation results in best performance ?

Last Answer : voltage commutation

Chopper controlled DC motor

Description : Chopper controlled DC motor

Last Answer : Chopper controlled DC motor

State the application of FET

Description : State the application of FET

Last Answer : Applications of FET : * As input amplifiers in oscilloscopes, electronic voltmeters and other measuring and testing equipment because high input impedance reduces loading effect to the minimum. * As Constant ... Used as Analog switch. * As a Voltage Variable Resistor (VVR) in operational amplifiers.

Define pinch off voltage and drain resistance of FET.

Description : Define pinch off voltage and drain resistance of FET.

Last Answer : 1 . Pinch-off Voltage: It is the value of the drain to source voltage VDS at which the drain current ID reaches its constant saturation value. Any further increase in VDS does not have any ... drain to source voltage to the change in drain current. It is also called AC/dynamic drain resistance.

List different types of FET.

Description : List different types of FET.

Last Answer : Types of FETs:  1. Junction FET (JFET) i. N-Channel JFET ii. P-Channel JFET  2. MOSFET i. E-MOSFET ii. D-MOSFET 

is IGBT costlier than BJT and MOSFET?

Last Answer : Yes IGBT is costlier than BJT and MOSFET.

What is a BJT?

Description : What is a BJT?

Last Answer : Bipolar Junction Transistor (BJT): BJT is a Bipolar device. (Uses both electrons and holes charge carrier for current conduction) Two Junctions (Emitter junction & collector ... mode (Current amplification) Cutoff mode (Open switch) Saturation mode (Close switch)

does the BJT have internal capacitance?

Last Answer : Yes BJT have internal capacitances.

in which region BJT act as a switch?

Last Answer : BJT act as switch in saturation and  cutoff region ( ON state in saturation region and OFF state in cut-off region )

in which BJT operating region both the junctions are reverse biased?

Last Answer : In cut-off region of BJT both the emitter-base junction and collector-base junction are reverse biased.

in which region BJT act as amplifier?

Last Answer : Active region of BJT act as amplifier.

what are the three operating regions of BJT?

Last Answer : Active , Saturation , Cut-off region of operations in BJT.

Does BJT have second breakdown problem?

Last Answer : Yes BJT have second breakdown problem.

Is BJT current controlled or voltage controlled?

Last Answer : BJT is current controlled device.

BJT have how many terminals?

Last Answer : BJT have three terminals Base, emitter and collector.

why bjt is called current controlled device?

Last Answer : In  BJT  there  is  movement  of   electrons  and  holes   accros  the  junctions  which  is  basicaly  current  flow.

when bjt is in cutoff ?

Last Answer : When Q-point is at cut off region means it is just above the horizontal axis VCE

what is bjt biasing?

Last Answer : The proper flow of zero signal collector current and the maintenance of the proper collector emmiter voltage during passage of single called as transistor biasing

bjt what is beta ?

Last Answer : Beta is the current gain which is the ratio of collector current to base current.

bjt is active or passive?

Last Answer : BJT control the flow of electron so it is a active device.

is bjt a voltage controlled device ?

Last Answer : No, BJT is a current controlled device .

what does bjt stand for?

Last Answer : Bipolar junction transistor

what are bjt amplifiers used for?

Last Answer : Transformer coupled amplifiers Direct coupled amplifiers Multistage amplifiers Darlington amplifiers Emmiter follower

what are bjt transistors?

Description : what are bjt transistors?

Last Answer : Bjt transistor is a type of transistor which  uses both electrons and hole charge carrier.bjts are used as switches and amplifiers.They amplify currents.

Operating frequency of power MOSFET is higher than that of power BJT. Justify the statement.

Description : Operating frequency of power MOSFET is higher than that of power BJT. Justify the statement.

Last Answer : Power MOSFET have high turning on and turning off capability high switching speed of MOSFET is due to the high rate of change of drain voltage. The switching losses of power MOSFET ... lower frequency. Hence, operating frequency of power MOSFET is higher than that of power BJT.

State 2 advantages of JFET over BJT.

Description : State 2 advantages of JFET over BJT.

Last Answer : Advantages of JFET over BJT: 1) High input impedance 2) Better thermal stability 3) Produce less noise 4) Smaller than BJT 5) Rugged in construction and simpler to fabricate 6) High degree of isolation between Input and Output. 

List specification of BJT.

Description : List specification of BJT.

Last Answer : * The bipolar junction transistor (BJT) has small signal current gain, α (hfb). * Maximum collector current Ic (max). * Maximum collector to emitter voltage, VCE (max). * Collector to emitter ... . * Collector to emitter cut off voltage, VCEO. * Base emitter saturation voltage, VBE (sat).

State reason BJT is called as bipolar junction transistor.

Description : State reason BJT is called as bipolar junction transistor.

Last Answer : BJT is called bipolar junction transistor because in BJT current conduction takes place due to majority as well as minority charge carriers.

List configurations of BJT.

Description : List configurations of BJT. 

Last Answer : Configurations of BJT : 1) Common Base (CB) configuration 2) Common Emitter (CE) configuration 3) Common Collector (CC) configuration

State the need of biasing of BJT.

Description : State the need of biasing of BJT.

Last Answer : Need of biasing: The basic need of transistor biasing is to keep the base-emitter (B-E) junction properly forward biased and the collector-emitter (C-E) junction properly reverse biased ... transistor biasing is necessary for normal and proper operation of transistor to be used for amplification. 

Draw circuit diagram of voltage divider biasing list two advantages of voltage divider biasing of BJT.

Description : Draw circuit diagram of voltage divider biasing list two advantages of voltage divider biasing of BJT.

Last Answer : Two advantages of voltage divider biasing of BJT. 1. It is very simple method of transistor biasing. 2. The biasing conditions can be very easily set. 3. there is no loading of ... 5. The resistor RE introduces a negative feedback. So all the advantages of negative feedback are obtained. 

If the base current of a BJT is 250 µA and emitter current is 15 mA, then the common base current gain will be

Description :  If the base current of a BJT is 250 µA and emitter current is 15 mA, then the common base current gain will be A) 0.98 B) 0.41 C) 59 D) 55  

Last Answer :  If the base current of a BJT is 250 µA and emitter current is 15 mA, then the common base current gain will be 0.98 

Which phenomenon is present in thyristors but absent in BJT, MOSFET and IGBT ?

Description : Which phenomenon is present in thyristors but absent in BJT, MOSFET and IGBT ? (A) forward conduction (B) latching (C) forward blocking (D) reverse breakdown

Last Answer : Which phenomenon is present in thyristors but absent in BJT, MOSFET and IGBT ? (A) forward conduction (B) latching (C) forward blocking (D) reverse breakdown

What is a BJT amplifier?

Description : What is a BJT amplifier?

Last Answer : Bilpolar Juntion transistor , this fuction is control the current

Explain open emitter BJT drive circuit.

Description : Explain open emitter BJT drive circuit.

Last Answer : open emitter BJT drive circuit:

Explain the formation of parasitic BJT and parasitic diode in Power MOSFET.

Description : Explain the formation of parasitic BJT and parasitic diode in Power MOSFET. Can parasitic diode be used in same power electronics applications?

Last Answer : Parasitic Diode: The parasitic diode is in between drain and source. The MOSFET structure itself contains parasitic diode or body drain diode. This parasitic diode allows the reverse flow of current when the ... of MOSFET as a BJT collector. Parasitic BJT operates in the cut-off region.

Compare BJT, MOSFET and IGBT .

Description : Compare BJT, MOSFET and IGBT .

Last Answer : BJT MOSFET IGBT BJT is a current controlled device. MOSFET is a voltage controlled device. IGBT is a voltage controlled device. The input impedance of BJT is low. ... is minority carrier device. MOSFET is majority carrier device. IGBT is minority carrier device.

what is the value of Beta in power BJT?

Description : What is the value of Beta in power BJT?

Last Answer : The beta value in power BJT is 5 to 10.

Explain the on state losses in power BJT.

Description : Explain the on state losses in power BJT.

Last Answer : On state losses in power BJT: Transistor have four types of losses one is turn on state losses second is turn off state losses third is turn on switching losses and fourth is turn ... ON = VCE sat x IC With increasing collector current collector to emitter saturation voltage increases.

why IGBT is preferred as a power switch over both power BJT and MOSFET?

Last Answer : Because it has a higher switching frequency and heat tolerance.

why igbt is used instead of bjt and mosfet?

Last Answer : ON state losses of IGBT is less as compared to MOSFET and BJT.

why the bjt is known as current controlled device and fet is known as voltage controlled device ?

Description : why the bjt is known as current controlled device and fet is known as voltage controlled device ?

Last Answer : Ans- 1. In BJT because of the current the output will vary. 2. Where as in FET by means of Voltage the output is varied.

Comparison of BJT and FET

Description : Comparison of BJT and FET

Last Answer : FET BJT It is unipolar device i.e. current in the device is carried either by electrons or holes It is bipolar device i.e. current in the device is carried either by both ... is comparatively more noisy. It is relatively immune to radiation. It is susceptible to radiation