Why does my motorcycle ride differently after i hit a high RPM?

Why does my motorcycle ride differently after i hit a high RPM?
by

1 Answer

Answer :

Are you in the same gear at the same speed. Usually if you are accelerating, you are in a lower gear. Once you get up to speed, it is easy to stay in the higher gear as you are slowing down. If you open the throttle in high gear from 40 mph it will sound like your engine is laboring. Make sure to downshift.
by

Related questions

What is a safe RPM to make my upshift on a motorcycle?

Description : What is a safe RPM to make my upshift on a motorcycle?

Last Answer : Don’t lug. Stay in a lower gear. Make 5,000 redline.

What's the procedure when you run out of gas on a motorcycle while riding?

Description : What's the procedure when you run out of gas on a motorcycle while riding?

Last Answer : I would make sure you have enough gas next time you ride. Fool proof.

Turning off motorcycle...Engine cut-off switch, or key?

Description : Turning off motorcycle...Engine cut-off switch, or key?

Last Answer : I just took the Basic Rider Course last month, and they taught us to use the switch and then the key.

New Zealanders: I have a full (car) licence and want to get a motorcycle licence. Do i need to go through Learners, Restricted and then Full again?

Description : New Zealanders: I have a full (car) licence and want to get a motorcycle licence. Do i need to go through Learners, Restricted and then Full again?

Last Answer : Isn’t a motercycle licence differant from a car licence? It is here and you need to go for a permit for the motercycle licence. It is a totally differant licence. But that is here in Maine.

What to do during a 14 hour car ride?

Description : What to do during a 14 hour car ride?

Last Answer : sing TV sitcom songs and fuss about the words. that should hold you about an hour.

In a stick shift car, is it easier on the clutch to pop it and get some jerkiness, or to ride it a bit for a smoother transition?

Description : In a stick shift car, is it easier on the clutch to pop it and get some jerkiness, or to ride it a bit for a smoother transition?

Last Answer : answer:The clutch is designed to slip, but it's also designed to wear slightly over time. If you ride it too much you can conceivably wear it out in a couple of hours. If you decide to ... get familiar with the car faster and really lessen the chances of causing damage. Good luck with the dispute.

Does anyone know any cost effective ways to improve the Honda fit's ride quality?

Description : Does anyone know any cost effective ways to improve the Honda fit's ride quality?

Last Answer : answer:It depends on your definition of cost effective. The cheap (free) way to do it would be to lower your tire pressure 2-3 psi at each corner. This will also slightly decrease gas mileage, ... going to make the handling sloppier. To what kind of car are you comparing the ride on the Fit?

"Do men ever ride on the back of a motorcycle while a girl drives?"?

Description : "Do men ever ride on the back of a motorcycle while a girl drives?"?

Last Answer : I’ve seen it a few times only with a dude driving. Never with a woman. I can’t wait to, though!

What motorcycle to learn to ride?

Description : I'm a beginner biker and I want to learn to ride.

Last Answer : It's best to start on a bike and get some fifty on the ride.

How dangerous is it to learn to ride a motorcycle?

Description : How dangerous is it to learn to ride a motorcycle?

Last Answer : There are many motorcycle accidents that happen every year. It is very dangerous for both seasoned bikers and those who are new to the sport. You can see some statistics here: http://www.webbikeworld.com/Motorcycle-Safety/motorcycle-accident-statistics.htm

Why do road bikes ride differently than mountain bikes (on pavement)

Description : Why do road bikes ride differently than mountain bikes (on pavement)

Last Answer : answer:Yikes, sorry! I think the main difference is they are much lighter, and the wheels are thinner (less traction with the ground).

What is the best place to get hit with an airbag?

Description : What is the best place to get hit with an airbag?

Last Answer : You should aim it at your chest. The bag is large enough to cover your face too. Also you should keep your hands at the 9 and 3 o’clock positions so they get pushed out if the bag detonates. (Used to be 10 and 2)

Would you willing let someone hit your vehicle?

Description : Would you willing let someone hit your vehicle?

Last Answer : Lol! Well you better hope they have insurance.. hahaha! I know what you mean though.. I get pretty frustrated with bad drivers myself.

What does it feel like to be hit by a car?

Description : What does it feel like to be hit by a car?

Last Answer : Depends on how hard you’re hit. I’ve bounced off of a number of cars, but never really been hit hard enough to do anything but bruise. Mine felt like a quick thud, much akin to accidentally hitting the corner of a desk/doorframe/etc.

Approximately when did car makers stop using two headlights (and start using one with a high beam filament)?

Description : Approximately when did car makers stop using two headlights (and start using one with a high beam filament)?

Last Answer : I’m sure that I’ve seen late-model BMW and Chevy cars with separate high/low beam headlights. And I’ve seen models from the 1970s which had single-lamp assemblies with the high and low beam filaments built into the lamp, as you suggest.

Boring question #26; what do you think about midsized cars sitting 4in high off the road on 20in wheels?

Description : Boring question #26; what do you think about midsized cars sitting 4in high off the road on 20in wheels?

Last Answer : It sounds goofy to me, but that is just my opinion.

Mercedes Owners...high cost of service at dealer question?

Description : Mercedes Owners...high cost of service at dealer question?

Last Answer : There is usually a specialist in town who can do all.

A reciprocating compressor is not suitable for use as a supercharger because: A. it runs at lower rpm B. the pressure ratio is high C. volumetric efficiency is high D. it is bulky and can handle small quantity of air

Description : A reciprocating compressor is not suitable for use as a supercharger because: A. it runs at lower rpm B. the pressure ratio is high C. volumetric efficiency is high D. it is bulky and can handle small quantity of air

Last Answer : ANSWER : D

Screw conveyors are (A) Run at very high rpm (B) Suitable for sticky materials (C) Suitable for highly abrasive materials (D) All (A), (B) and (C)

Description : Screw conveyors are (A) Run at very high rpm (B) Suitable for sticky materials (C) Suitable for highly abrasive materials (D) All (A), (B) and (C)

Last Answer : (B) Suitable for sticky materials

A propeller agitator (A) Produces mainly axial flow (B) Is used for mixing high viscosity pastes (C) Runs at very slow speed (2 rpm) (D) All (A), (B) and (C)

Description : A propeller agitator (A) Produces mainly axial flow (B) Is used for mixing high viscosity pastes (C) Runs at very slow speed (2 rpm) (D) All (A), (B) and (C)

Last Answer : (A) Produces mainly axial flow

Delivery of insufficient quantity of liquid by a pump may be caused by (A) Air leak in the inlet (B) Low rpm (C) Too high a lift (D) All (A), (B) and (C)

Description : Delivery of insufficient quantity of liquid by a pump may be caused by (A) Air leak in the inlet (B) Low rpm (C) Too high a lift (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Which statement best describes the operating principle of a constant-speed propeller? a. As throttle setting is changed by the pilot, the prop governor causes pitch angle of the propeller blades to remain unchanged b. The propeller control regulates the engine RPM and in turn the propeller RPM c. A high blade angle, or increased pitch, reduces the propeller drag and allows more engine power for take-offs d. As the propeller control setting is changed by the pilot, the RPM of the engines remains constant as the pitch angle of the propeller changes

Description : Which statement best describes the operating principle of a constant-speed propeller? a. As throttle setting is changed by the pilot, the prop governor causes pitch angle of the propeller blades to ... the pilot, the RPM of the engines remains constant as the pitch angle of the propeller changes

Last Answer : b. The propeller control regulates the engine RPM and in turn the propeller RPM

peed of a high speed engine is (a) <350 rpm (b) 350-1000 rpm (c) >1000rpm (d) none of the above

Description : peed of a high speed engine is (a) 1000rpm (d) none of the above

Last Answer : (c) >1000rpm

How soon after an photo radar speeding ticket is registered before one can get a second ticket?

Description : How soon after an photo radar speeding ticket is registered before one can get a second ticket?

Last Answer : Just drive really, really fast, and try to make it in 4:55.

Is it normal for a 440 6 barrel 70 cuda engine to get really hot after a 15 mile drive?

Description : Is it normal for a 440 6 barrel 70 cuda engine to get really hot after a 15 mile drive?

Last Answer : You might wish to have the cooling system and radiator flushed, but how hot is awful hot. Sometimes running a bit lean can make an engine run hot. Also, if the radiator is not the correct one for the engine ... is pretty much all GM and it was an old 409, but I figure the basics are about the same.

If leaving car for a month, should I have the engine started after two weeks?

Description : If leaving car for a month, should I have the engine started after two weeks?

Last Answer : I think the car will be fine if it’s going to sit for a month. That’s not very long. I once left my car sitting for almost 2 years, and I had someone run it maybe every 4–6 months or so. My point is, it will be fine for a month. Enjoy your trip and don’t worry about it!

Factory or after-market brake pads?

Description : Factory or after-market brake pads?

Last Answer : answer:That really depends. Sometimes the aftermarket ones are cheaper but better, sometimes the aftermarket ones are cheap for a reason, sometimes they are the same pad with different prices, and sometimes ... Too many variables. What sort of vehicle is it, and what brand are the aftermarket ones?

I am thinking of making wooden miniature (toy) cars; can I remodel them after real brand cars?

Description : I am thinking of making wooden miniature (toy) cars; can I remodel them after real brand cars?

Last Answer : answer:Better to get these companies approval in writing, before you make any attempt at selling them. This is what copyright laws are all about. I saw your display and you certainly are equipped to make the vehicle copies. Better safe, than sorry.

Have you ever known of a car that lasted 2 years after an engine replacement?

Description : Have you ever known of a car that lasted 2 years after an engine replacement?

Last Answer : answer:I just saw a clip of someone who put a 3800 engine in place of a 3.1L into an old Grand Prix Turbo. I’ll check back in two years. I promise. ….

Where can I find after market car A/C knobs for a car?

Description : Where can I find after market car A/C knobs for a car?

Last Answer : Depending on the car, probably the best and easiest solution would be to go to a salvage yard and find what fits. First find a car like yours, then go around and see what you like, Checking to ... can either order the ones you find, or order new ones from the dealership of the vehicle you found.

94 Ford Aerostar van acting up after unrelated repairs... any ideas?

Description : 94 Ford Aerostar van acting up after unrelated repairs... any ideas?

Last Answer : The wheel bearing might have to do with the crazy speedometer. That might have been the wheel that measured the rotation of the wheel, but the stalling is out of left field. If the stalling thing happens ... in the right direction. All you have to do is find what triggers what and go from there.

Any ideas on how to avoid getting your credit hurt, before-during-after a care REPO?

Description : Any ideas on how to avoid getting your credit hurt, before-during-after a care REPO?

Last Answer : Make the payments for him, and sell the car before it gets repossessed. And in future don’t co-sign loans for anyone you’re not willing to sacrifice your credit history and your savings for.

Car problem: Brake light staying on after I turn the car and lights off?

Description : Car problem: Brake light staying on after I turn the car and lights off?

Last Answer : Get your car to a mechanic – you either have a bad brake light switch or some kind of short. If you don’t have jumper cables you may have to call a tow truck.

How does one turn off the engine after hotwiring a car?

Description : How does one turn off the engine after hotwiring a car?

Last Answer : i think it depends on how it was hotwired. pulling the wires apart would probably do it.

Tips for returning a car after a lease?

Description : Tips for returning a car after a lease?

Last Answer : return it nice and clean!

What is the total acceleration of a point on the rim of a flywheel 4 mts in diameter 0.6 see after it has started from rest if it accelarates uniformly from rest to 2000 rpm in 20 secs. a.68.9 mts/sec2 b.102.6 mts/sec2 c.78.94 mts/sec2 d.107 dynes e.33.2 mts/sec2

Description : What is the total acceleration of a point on the rim of a flywheel 4 mts in diameter 0.6 see after it has started from rest if it accelarates uniformly from rest to 2000 rpm in 20 secs. a.68.9 mts/sec2 b.102.6 mts/sec2 c.78.94 mts/sec2 d.107 dynes e.33.2 mts/sec2

Last Answer : c. 78.94 mts/sec2

A flywheel starting from rest and accelerating uniformly performs 25 revolutions in 5 sec. Its angular velocity in rpm after 10 seconds would be a.50 rpm b.20 rpm c.25 rpm d.60 rpm e.45 rpm

Description : A flywheel starting from rest and accelerating uniformly performs 25 revolutions in 5 sec. Its angular velocity in rpm after 10 seconds would be a.50 rpm b.20 rpm c.25 rpm d.60 rpm e.45 rpm

Last Answer : b. 20 rpm

Why does my 2004 Xterra stall when put in gear It Starts idling at 1200 rpm after 15 min it idles down and drives fine?

Description : Why does my 2004 Xterra stall when put in gear It Starts idling at 1200 rpm after 15 min it idles down and drives fine?

Last Answer : Look for a vacuum leak.

A four pole, 60 Hz, three-phase synchronous motor comes up to 1760 RPM when started as an induction motor. What is the percent slip after the rotor field is energized? A. 0 B. 1.1 C. 2.2 D. 3.3

Description : A four pole, 60 Hz, three-phase synchronous motor comes up to 1760 RPM when started as an induction motor. What is the percent slip after the rotor field is energized? A. 0 B. 1.1 C. 2.2 D. 3.3

Last Answer : Answer: A

Which three customer groups “ride the wave of technology” and are considered to be in the high technology segments? a. Performance, High End, and Size b. Performance, Traditional, and High End c. Performance, Low End, and Size d. Traditional, High End, and Size e. Traditional, Low End, and Size

Description : Which three customer groups ride the wave of technology and are considered to be in the high technology segments? a. Performance, High End, and Size b. Performance, Traditional, and High End c. ... End, and Size d. Traditional, High End, and Size e. Traditional, Low End, and Size

Last Answer : a. Performance, High End, and Size

If you could do high school all over again, would you do anything differently?

Description : If you could do high school all over again, would you do anything differently?

Last Answer : I would’ve grown a pair. Also, if I’d been a great student when I was young, I’d be able to speak a total of 5 languages now. What a shame.

What should I do to keep my eyes from becoming all red and watery after a long bike ride?

Description : What should I do to keep my eyes from becoming all red and watery after a long bike ride?

Last Answer : Googles??

What is the main reason that vaqueros no longer needed to ride the wide open spaces after the civil war?

Description : What is the main reason that vaqueros no longer needed to ride the wide open spaces after the civil war?

Last Answer : Railroads were used to transport Cattells to market in Eastern in a western cities.

He can buy a monthly pass for $30 and pays $0.08 per ride, or he can pay $2.30 per ride after how many rides will the two options cost the same which is the better option of jake's takes the bus 5 days per week for 4?

Description : He can buy a monthly pass for $30 and pays $0.08 per ride, or he can pay $2.30 per ride after how many rides will the two options cost the same which is the better option of jake's takes the bus 5 days per week for 4?

Last Answer : 35

Shortly after take-off, the altitude of the aeroplane suffers an abrupt pitch-up and IAS rapidly decreases followed quickly by a decrease in altitude. Engine indications are normal. You should suspect what and what should you do? a. Marked temperature drop; apply full power b. Loss of head wind or an increase in tail wind; apply full power c. Incipient engine failure (ignore instruments); lower the nose to gain airspeed d. Local clear air turbulence; reduce speed to VRA and ride it out

Description : Shortly after take-off, the altitude of the aeroplane suffers an abrupt pitch-up and IAS rapidly decreases followed quickly by a decrease in altitude. Engine indications are normal. You should suspect what ... to gain airspeed d. Local clear air turbulence; reduce speed to VRA and ride it out

Last Answer : b. Loss of head wind or an increase in tail wind; apply full power

Does society treat miscarried/stillborn babies differently than infants that die after birth? (Please read details)

Description : Does society treat miscarried/stillborn babies differently than infants that die after birth? (Please read details)

Last Answer : answer:!) I can't speak for society. In my limited experience stillborn children are not treated as babies by hospital staff. My experience is so limited as to be statistically insignificant. 2) Yes. ... have no particular opinion about it and I don't see the relevance to the question as a whole.

Am I worrying too much or is my dad just ignorant?

Description : Am I worrying too much or is my dad just ignorant?

Last Answer : My check engine light it flashing. Its not just a solid yellow light

How do they do smog tests on cars?

Description : How do they do smog tests on cars?

Last Answer : Smog as in a combination of mist and fog?

Do any Jellies know anyone at Hyundai Customer Care?

Description : Do any Jellies know anyone at Hyundai Customer Care?

Last Answer : I don’t, but you could try your state insurance commissioner.