Description : To couple a coaxial line to parallel line, it is better to use a ______. A. Slotted line B. Quarter-wave transformer C. Directional Coupler D. Balun
Last Answer : D. Balun
Description : To connect coaxial line to a parallel-wire _________ is the best to use. A. directional coupler B. quarter-wave transformer C. balun D. slotted line
Last Answer : C. balun
Description : Best choice of transmission line component to couple a coaxial line to a parallel-wire line A. Shorting B. Balun C. Slotted line D. Directional coupler
Last Answer : B. Balun
Description : Fortransmission-line loadmatchingover a range offrequencies,itisbesttouse a a. balun b. broadband directional coupler c. double stub d. single stub of adjustable position
Last Answer : c. double stub
Description : What type of balun (balanced-to-unbalanced) is used in high frequency applications? A. Transformer type balun B. A specially configured coaxial transmission line C. A specially configured parallel-wire line D. A λ/2 transformer balun
Last Answer : B. A specially configured coaxial transmission line
Description : Most mobile satellite array uses ___________ in transforming 50 to 150 Ω impedance. A. stub B. balun C. quarter-wavelength transformer D. microstrip tapers.
Last Answer : C. quarter-wavelength transformer
Description : Impedance inversionmaybe obtainedwith a. a short-circuited stub b. an open-circuited stub c. a quarter-wave line d. a half-wave line
Last Answer : c. a quarter-wave line
Description : The output from a full wave rectifier is (a) A pulsating uni-directional current (b) A DC voltage (c) Zero (d) An AC voltage
Last Answer : a) A pulsating uni-directional current
Description : A component that samples the microwave signal travelling in one direction down to the transmission line A. Isolator B. Combiner C. Directional coupler D. Attenuator
Last Answer : C. Directional coupler
Description : All electrical appliances are connected in parallel to each other between the main line and neutral wire to get a. same current b. same current and potential difference c. different current but same potential difference d. different current and potential differences
Last Answer : c. different current but same potential difference
Description : One ofthe followingis not a reason forthe use of anantenna coupler: a. To make the antenna look resistive b. To provide the output amplifier with the correct load impedance c. To discriminate against harmonics d. To prevent reradiation of the local oscillator
Last Answer : d. To prevent reradiation of the local oscillator
Description : Curl cannot be employed in which one of the following? a) Directional coupler b) Magic Tee c) Isolator and Terminator d) Waveguides
Last Answer : d) Waveguides
Description : What happens to reflected energy that enters a directional coupler that is designed to sample incident energy?
Last Answer : . The reflected energy adds at the absorbent material and is absorbed.
Description : in a directional coupler that is designed to sample the incident energy, what happens to the two portions of the wavefront when they arrive at the pickup probe?
Last Answer : The wavefront portions add.
Description : What is the purpose of the absorbent material in a directional coupler?
Last Answer : Absorb the energy not directed at the pick-up probe and a portion of the overall energy
Description : How far apart are the two holes in a simple directional coupler?
Last Answer : 1/4 wavelength.
Description : What is the primary purpose of a directional coupler?
Last Answer : Sampling energy within a waveguide.
Description : Describe a directional coupler.
Last Answer : A fiber optic coupler that prevents the transfer of power between input fibers.
Description : Describe the working of directional coupler with neat diagram.
Last Answer : Directional couplers are devices that will pass signal across one path while passing a much smaller signal along another path. One of the most common uses of the directional coupler is to ... . The frequency determines the separation of the two holes as a fraction of the wavelength.
Description : In a directional coupler: (1) Isolation (dB) equals coupling plus directivity (2) Coupling (dB) equals isolation plus directivity (3) Directivity (dB) equals isolation plus coupling (4) Isolation (dB) equals (coupling) (directivity)
Last Answer : In a directional coupler: Isolation (dB) equals coupling plus directivity.
Description : Aship-to-ship communicationssystemisplagued byfading.The bestsolutionseemstobe useof a. a more directional antenna b. a broadband antenna c. frequency diversity d. space diversity
Last Answer : c. frequency diversity
Description : Themaindisadvantage ofthe two-hole directional coupleris a. low directional coupling b. poor directivity c. high SWR d.narrowbandwidth
Last Answer : d.narrowbandwidth
Description : A wire loop is moved parallel to a uniform magnetic field. The induced emf in the loop: a. depends on the shape b. depends on area c. depends on nature of loop d. zero
Last Answer : d. zero
Description : A load of 200 ohm is used to match 300 ohm transmission line to achieve SWR=1. Find out the required characteristic impedance of a quarter of a quarter wave transformer connected directly to the load.
Last Answer : Solution :
Description : To couple a coaxial line to a parallel wire line, it is best to use a: (1) A slotted line (2) Balun (3) Directional coupler (4) Quarter wave line transformer
Last Answer : To couple a coaxial line to a parallel wire line, it is best to use a: Balun.
Description : Thegroundwave eventuallydisappears, as onemoves awayfromthetransmitter, because of a. interference from the sky wave b. loss of line-of-sight conditions c. maximumsingle-hop distance limitation d. tilting
Last Answer : d. tilting
Description : How quarter wave transformer is used for impedance matching.
Last Answer : In all applications of transmission line, it is required that the load be matched to line, Which requires tuning out the unwanted load reactance and the transformation of resulting impedance to the required value ... Step down transformer If ZL <Zo then it acts as a Step up transformer
Description : List and explain the properties of quarter wave transformer.
Last Answer : Properties of quarter wave transformer: 1. Impedance transfomation: it provides impedance transformation upto the highest frequencies and is compatible with transmission line. 2. Impedance inversion: if ZL is ... or step up transformer,depending on whether ZL IS greater than or less than ZO.
Description : It is useful to refer to an isotropic radiator. A. when comparing the gains of directional antennas B. when testing a transmission line for standing wave ratio C. when (in the northern hemisphere) directing the transmission D. when using a dummy load to tune a transmitter
Last Answer : A. when comparing the gains of directional antennas
Description : When is it useful to refer to an isotropic radiator? A. When comparing the gains of directional antennas B. When testing a transmission line for standing wave ratio C. When (in the northern ... ) directing the transmission in a southerly direction D. When using a dummy load to tune a transmitter
Last Answer : A. When comparing the gains of directional antennas
Description : Which one is an antenna coupling unit? A. Coupler B. Diplexer C. Lecher wire D. Duplexer
Last Answer : B. Diplexer
Description : Please ripley me due to emergency
Last Answer : To calculate the flux density in the ring, you need to use the following formula: B = (μ * I * N) / (2 * π * r) where: B is the flux density in the ring (in teslas) μ is the relative permeability ... 2 * π * 0.127 m) = 0.53 T So the flux density in the ring would be approximately 0.53 teslas.
Description : How to stop a signal going through a wire?
Last Answer : Use a switch or a variable resistor
Last Answer : her And Cable In The difference Yes His Yes Just Only A Conductor Where Cable Two Or Even more Of the conductor A Group.
Description : Specific resistance of a wire a. will depend on its length b. will depend on its radius c. will depend on the type of material of the wire d. will depend on none of the above
Last Answer : c. will depend on the type of material of the wire
Description : Resistance of a wire on increasing its temperature will a. increase with rise in temperature b. decrease with rise in temperature c. will remain same d. depends upon altitude of experimentation
Last Answer : a. increase with rise in temperature
Description : A wire of uniform area of cross-section A length L and resistance R is cut into two parts. Resistivity of each part a. remains the same b. is doubled c. is halved d. becomes zero
Last Answer : a. remains the same
Description : A wire having very high value of conductance is said to be a. very good conductor b. moderately good conductor c. an insulator d. None
Last Answer : a. very good conductor
Description : When current of one ampere is flowing across any cross-section of wire in one second, then the quantity of charge is said to be: (a) One coulomb (b) Three coulomb (c) One micro-coulomb (d) None of above
Last Answer : (a) One coulomb
Description : The resistance of a few meters of wire conductor in closed electrical circuit is?
Last Answer : The resistance of a few meters of wire conductor in closed electrical circuit is practically zero.
Description : A device that connects two dissimilar networks and performs the protocol conversion. A. Gateway B. Coupler C. Transformer D. Converter
Last Answer : A. Gateway
Description : What is a current transformer and voltage transformer?*
Last Answer : In electrical engineering, a current transformer (CT) is used for measurement of electric currents. Current transformers, together with voltage transformers (VT) (potential transformers (PT)), ... transformers are commonly used in metering and protective relays in the electrical power industry.
Description : Why are motor ratings given in KW and that of alternator and transformer given in KVA?
Last Answer : kW is the output mechanical power of a motor and is expressed in kW. kVA is the net (apparent) power input to the transformer. This input power is the output + losses. kW = kVA x system power factor
Description : Which of the following converts electric energy into mechanical energy: a. Transformer b. DC generator c. Motor d. AC generator
Last Answer : d. AC generato
Description : The induced current in transformer which produced in the direction perpendicular to flux, is known as: a. Conventional current b. electronic current c. Perpendicular current d. Eddy current
Last Answer : c. Perpendicular current
Description : The most common source of AC voltage is: a. motor b. generator c. cell d. transformer
Last Answer : c. cell
Description : A transformer steps down 220V to 40 volts. If the secondary turns are 40 then primary turns will be: a. 20 b. 40 c. 120 d. 220
Last Answer : d. 220V
Description : The loss of energy over each A.C cycle magnetization and demagnetization of transformer, is called: a. Magnetization loss b. Hysteresis loss c. Demagnetization loss d. energy loss
Last Answer : c. Demagnetization loss
Description : The application of mutual induction is: a. TV b. Radio c. Transformer d. Motor
Last Answer : c. Transformer
Description : An ideal transformer always obeys the law of conservation of........: a. energy b. momentum c. charge d. Flux
Last Answer : b. momentum