With an almost discharged battery there will be: a. A decrease of voltage with increasing load b. Increase of current with decrease of voltage c. Decrease of current with increasing load d. Increase of voltage with increasing load

With an almost discharged battery there will be:
a. A decrease of voltage with increasing load
b. Increase of current with decrease of voltage
c. Decrease of current with increasing load
d. Increase of voltage with increasing load
by

1 Answer

Answer :

a. A decrease of voltage with increasing load
by

Related questions

With an almost discharged battery there will be:

Description : With an almost discharged battery there will be:

Last Answer : A. decrease in voltage and increase in load.

When a battery is nearly discharged, does the

Description : When a battery is nearly discharged, does the

Last Answer : B. voltage and current decrease

Increasing the load to the secondary windings of a transformer will cause a/an ____________. A. decrease in the primary voltage B. increase in the primary voltage C. decrease in the primary current D. increase in the primary current

Description : Increasing the load to the secondary windings of a transformer will cause a/an ____________. A. decrease in the primary voltage B. increase in the primary voltage C. decrease in the primary current D. increase in the primary current

Last Answer : Answer: D

A lead-acid battery cell sustaining a short circuit _______. A. will be indicated by lime accumulation on the terminal posts B. will have unusually high cell voltage C. will become excessively heated while being charged D. cannot be completely discharged under load

Description : A lead-acid battery cell sustaining a short circuit _______. A. will be indicated by lime accumulation on the terminal posts B. will have unusually high cell voltage C. will become excessively heated while being charged D. cannot be completely discharged under load

Last Answer : Answer: C

An inversion is: a. A decrease of pressure with height b. A decrease of temperature with height c. An increase of temperature with height d. An increase of pressure with height

Description : An inversion is:  a. A decrease of pressure with height  b. A decrease of temperature with height  c. An increase of temperature with height  d. An increase of pressure with height

Last Answer : c. An increase of temperature with height

What is normally the most effective measure to reduce or avoid CAT effects? a. Change of flight level b. Change of course c. Increase of speed d. Decrease of speed

Description : What is normally the most effective measure to reduce or avoid CAT effects?  a. Change of flight level  b. Change of course  c. Increase of speed  d. Decrease of speed

Last Answer : a. Change of flight level

You are flying at a constant FL 290 and a constant mach number. The total temperature increases by 5°. The CAS will: a. Remain approximately constant b. Increase by 10 kts c. Decrease by 10 kts d. Will increase or decrease depending on whether you are above or below ISA

Description : You are flying at a constant FL 290 and a constant mach number. The total temperature increases by 5°. The CAS will: a. Remain approximately constant b. Increase by 10 kts c. Decrease by 10 kts d. Will increase or decrease depending on whether you are above or below ISA

Last Answer : a. Remain approximately constant

Local action in a dry-cell, or lead-acid storage battery is the process whereby ________________. A. hydrogen gas is liberated B. the electrolyte compensates for overcharging C. potassium hydroxide absorbs carbon dioxide from the air D. the battery becomes discharged without being connected to a load

Description : Local action in a dry-cell, or lead-acid storage battery is the process whereby ________________. A. hydrogen gas is liberated B. the electrolyte compensates for overcharging C. potassium hydroxide ... carbon dioxide from the air D. the battery becomes discharged without being connected to a load

Last Answer : Answer: D

At what voltage is a NICAD battery considered to be fully discharged?

Description : At what voltage is a NICAD battery considered to be fully discharged?

Last Answer : At 1.1 volts.

A pilot suffering from decompression sickness should: a. Descend to a lower level where the symptoms will disappear and continue the flight at this or a lower level b. Decrease the cabin pressure to relieve the symptoms c. Continue the flight at a lower altitude and carry out exercises to relieve the pain in the affected site d. Land as soon as possible and seek medical assistance

Description : A pilot suffering from decompression sickness should: a. Descend to a lower level where the symptoms will disappear and continue the flight at this or a lower level b. Decrease the cabin pressure ... relieve the pain in the affected site d. Land as soon as possible and seek medical assistance

Last Answer : d. Land as soon as possible and seek medical assistance

The LED indicator on the emergency torch is flashing at 4 seconds intervals. This indicates: a. The battery is charging b. The torch is serviceable c. The battery needs replacing d. The filament is broken

Description : The LED indicator on the emergency torch is flashing at 4 seconds intervals. This indicates: a. The battery is charging b. The torch is serviceable c. The battery needs replacing d. The filament is broken

Last Answer : b. The torch is serviceable

Unidirectional tandem gene arrays are significant in ________ a. Increase in recombinant gene product with increasing plasmid number. b. Increase in recombinant gene product without increasing plasmid number. c. Decrease in polymerase enzyme battery with increasing plasmid numbers. d. Decrease in strong promotor with increase in plasmid number

Description : Unidirectional tandem gene arrays are significant in ________ a. Increase in recombinant gene product with increasing plasmid number. b. Increase in recombinant gene product without increasing plasmid ... increasing plasmid numbers. d. Decrease in strong promotor with increase in plasmid number

Last Answer : b. Increase in recombinant gene product without increasing plasmid number.

The useful load is:

Description : The useful load is:

Last Answer : TOM minus the DOM

Define the useful load:

Description : Define the useful load:

Last Answer : traffic load plus usable fuel mass

Given: DOM 33,510kt; Traffic load 7,600kg; Trip fuel 2040kg; Final reserve 983kg Alternative fuel 1100kg; Contingency 5% of trip fuel Which of the following is correct? a. Estimated landing mass at destination 43,193kg b. Estimated landing mass at destination 43,295kg c. Estimated take-off mass 43,295kg d. Estimated take-off mass 45,233kg

Description : Given: DOM 33,510kt; Traffic load 7,600kg; Trip fuel 2040kg; Final reserve 983kg Alternative fuel 1100kg; Contingency 5% of trip fuel Which of the following is correct? a. Estimated landing mass ... destination 43,295kg c. Estimated take-off mass 43,295kg d. Estimated take-off mass 45,233kg

Last Answer : b. Estimated landing mass at destination 43,295kg

Define the useful load: a. traffic load plus dry operating mass b. traffic load plus usable fuel mass c. dry operating mass plus usable fuel load d. that part of the traffic load which generates revenue

Description : Define the useful load: a. traffic load plus dry operating mass b. traffic load plus usable fuel mass c. dry operating mass plus usable fuel load d. that part of the traffic load which generates revenue

Last Answer : a. traffic load plus dry operating mass

If a CSD overheat warning is shown: a. The CSD can be disconnected and the pilot must control the alternator himself b. The pilot must throttle back to reduce the load on the alternator c. The CSD can be disconnected then reconnected later when the temperature has reduced d. The CSD can be disconnected but not used for the rest of the flight

Description : If a CSD overheat warning is shown: a. The CSD can be disconnected and the pilot must control the alternator himself b. The pilot must throttle back to reduce the load on the alternator c. The ... temperature has reduced d. The CSD can be disconnected but not used for the rest of the flight

Last Answer : d. The CSD can be disconnected but not used for the rest of the flight

Generally, as altitude increases: a. Temperature decreases and density increases b. Temperature, pressure and density decreases c. Temperature and pressure increase and density decreases d. Temperature decreases and pressure and density increase

Description : Generally, as altitude increases: a. Temperature decreases and density increases b. Temperature, pressure and density decreases c. Temperature and pressure increase and density decreases d. Temperature decreases and pressure and density increase

Last Answer : b. Temperature, pressure and density decreases

The best strategy to increase stress tolerance

Description : The best strategy to increase stress tolerance

Last Answer : learning, experience CRM

The best strategies to increase stress tolerance are: a. Planning, experience and self-control (fewer unexpected situation) b. Learning, experience and anticipation c. Learning, experience and CRM d. Planning, experience and CRM

Description : The best strategies to increase stress tolerance are: a. Planning, experience and self-control (fewer unexpected situation) b. Learning, experience and anticipation c. Learning, experience and CRM d. Planning, experience and CRM

Last Answer : c. Learning, experience and CRM

The effects of carbon monoxide: a. Increases with altitude b. Decreases with altitude c. Increases with increase of density d. Decreases with pressure loss

Description : The effects of carbon monoxide: a. Increases with altitude b. Decreases with altitude c. Increases with increase of density d. Decreases with pressure loss

Last Answer : a. Increases with altitude

What to do when inverter battery is fully discharged?

Description : What to do when inverter battery is fully discharged?

Last Answer : If the inverter battery is fully discharged then the inverter or UPS should put to OFF position and charge the inverter for enough time before putting it ON again. If the inverter is unable to charge the battery then you may charge it using another charger or inverter. Then connect it back again.

When a lead storage battery is discharged - (1) SO2 is evolved (2) Lead sulphate is consumed (3) Lead is formed (4) Sulphuric acid is consumed

Description : When a lead storage battery is discharged - (1) SO2 is evolved (2) Lead sulphate is consumed (3) Lead is formed (4) Sulphuric acid is consumed

Last Answer : (4) Sulphuric acid is consumed Explanation: Lead storage battery was invented by French physicist Gaston Plante in 1859. In the discharged state both the positive and negative plates become lead sulphate and the electrolyte loses much of its dissolved sulphuric acid and becomes primarily water.

If the illustrated device is fully discharged, what will be the result? EL-0061 A. The battery will be short circuited because the mud space will be filled with lead sulfate B. The electrolyte will be maximum sulfuric acid minimum water C. The electrolyte will be maximum water minimum sulfuric acid. D. The plates will be maximum lead oxide and sponge lead minimum lead sulfate.

Description : If the illustrated device is fully discharged, what will be the result? EL-0061 A. The battery will be short circuited because the mud space will be filled with lead sulfate B. The electrolyte ... minimum sulfuric acid. D. The plates will be maximum lead oxide and sponge lead minimum lead sulfate.

Last Answer : Answer: C

The specific gravity of the electrolyte solution in a lead acid battery _____________. A. is not effected during charging B. remains the same during discharge C. would read close to 1.830 when discharged D. gives an indication of the state of charge of the battery

Description : The specific gravity of the electrolyte solution in a lead acid battery _____________. A. is not effected during charging B. remains the same during discharge C. would read close to 1.830 when discharged D. gives an indication of the state of charge of the battery

Last Answer : Answer: D

Which of the problems listed will occur if a lead-acid battery is allowed to remain in a discharged condition for a long period of time? A. The battery may be unable to accept a full charge. B. The electrolyte will change to lead sulfate. C. The concentrated sulfuric acid will attack the lead peroxide plates. D. The separators will harden.

Description : Which of the problems listed will occur if a lead-acid battery is allowed to remain in a discharged condition for a long period of time? A. The battery may be unable to accept a full charge ... . C. The concentrated sulfuric acid will attack the lead peroxide plates. D. The separators will harden.

Last Answer : Answer: A

When checking the specific gravity of the battery electrolyte with a hydrometer, you should be aware that ________________. A. the battery is fully charged when the float sinks deepest into the electrolyte B. the battery is discharged when the float is highest in the electrolyte C. a hydrometer reading is accurate if taken immediately after water is added to the cell D. warm temperatures will lower the specific gravity of the electrolyte

Description : When checking the specific gravity of the battery electrolyte with a hydrometer, you should be aware that ________________. A. the battery is fully charged when the float sinks deepest into the ... is added to the cell D. warm temperatures will lower the specific gravity of the electrolyte

Last Answer : Answer: D

Which of the following statements concerning nickel-cadmium batteries is true? A. When mixing electrolyte always add acid to the water. B. Nickel-cadmium batteries can be charged and discharged only a limited number of times without damage to the cells. C. Nickel-cadmium batteries can be stored for a long time and still keep a full charge without additional charging. D. The electrolyte of an idle nickel-cadmium battery must be replaced monthly to maintain battery condition.

Description : Which of the following statements concerning nickel-cadmium batteries is true? A. When mixing electrolyte always add acid to the water. B. Nickel-cadmium batteries can be charged and ... The electrolyte of an idle nickel-cadmium battery must be replaced monthly to maintain battery condition.

Last Answer : Answer: C

The freezing point of the electrolyte in a fully charged lead-acid battery will be _____________. A. higher than in a discharged battery B. lower than in a discharged battery C. the same as in a discharged battery D. higher than in a discharged battery, but the specific gravity will be less

Description : The freezing point of the electrolyte in a fully charged lead-acid battery will be _____________. A. higher than in a discharged battery B. lower than in a discharged battery C. the same as in a discharged battery D. higher than in a discharged battery, but the specific gravity will be less

Last Answer : Answer: B

What factors that decide the VRLA battery to completely charged from fully discharged condition?

Description : What factors that decide the VRLA battery to completely charged from fully discharged condition?

Last Answer : Answer: Some of the important factors that determine the duration of the discharged battery to charge are: Duration of the discharge occurred Temperature at which battery is operating Size and efficiency of the charger

battery must be turned over to a charging station in winter if discharged by a) 50% b) 40% c) 30% d) 25%

Description : battery must be turned over to a charging station in winter if discharged by a) 50% b) 40% c) 30% d) 25%

Last Answer : d) 25%

Terminal potential difference of a battery is greater than its emf when a. the internal resistance of battery is infinite b. the internal resistance of battery is zero c. the battery is charged d. the battery is discharged

Description : Terminal potential difference of a battery is greater than its emf when a. the internal resistance of battery is infinite b. the internal resistance of battery is zero c. the battery is charged d. the battery is discharged

Last Answer : c. the battery is charged

When a lead storage battery is discharged, (1) SO2 is evolved (2) Lead sulphate is consumed (3) Lead is formed (4) Sulphuric acid is consumed

Description : When a lead storage battery is discharged, (1) SO2 is evolved (2) Lead sulphate is consumed (3) Lead is formed (4) Sulphuric acid is consumed 

Last Answer : Sulphuric acid is consumed

If there were no atmosphere, the length of the day would (a) decrease (b) remain unaffected (c) increase (d) be almost half

Description : If there were no atmosphere, the length of the day would (a) decrease (b) remain unaffected (c) increase (d) be almost half

Last Answer : Ans:(a)

The resistance of a conductor at absolute zero (OK) is a. zero almost b. infinite almost c. May increase or decrease d. None

Description : The resistance of a conductor at absolute zero (OK) is a. zero almost b. infinite almost c. May increase or decrease d. None

Last Answer : zero almost

Electrolysis is an impotant technique for extraction of metals, and each of the solution needs a minimum voltage to get discharged and this value is e

Description : Electrolysis is an impotant technique for extraction of metals, and each of the solution needs a minimum voltage to get discharged and this value is e

Last Answer : Electrolysis is an impotant technique for extraction of metals, and each of the solution needs a minimum voltage to get ... 3)` D. `H_(2)S_(2)O_(8)`

Electrolysis is an impotant technique for extraction of metals, and each of the solution needs a minimum voltage to get discharged and this value is e

Description : Electrolysis is an impotant technique for extraction of metals, and each of the solution needs a minimum voltage to get discharged and this value is e

Last Answer : Electrolysis is an impotant technique for extraction of metals, and each of the solution needs a minimum voltage to get ... ,H_(2)` D. `O_(2),H_(2)`

Electrolysis is an impotant technique for extraction of metals, and each of the solution needs a minimum voltage to get discharged and this value is e

Description : Electrolysis is an impotant technique for extraction of metals, and each of the solution needs a minimum voltage to get discharged and this value is e

Last Answer : Electrolysis is an impotant technique for extraction of metals, and each of the solution needs a minimum voltage to get ... ` C. `Br_(2)` D. `O_(2)`

At high discharge rates, nickel-cadmium storage batteries are superior to lead-acid batteries because they __________. A. require fewer cells for the same voltage and less mounting space B. are able to produce higher voltages and do not have to be charged as often C. can be charged and discharged many times without much damage D. have no individual cells to replace at the end of useful life

Description : At high discharge rates, nickel-cadmium storage batteries are superior to lead-acid batteries because they __________. A. require fewer cells for the same voltage and less mounting space B. are able to ... times without much damage D. have no individual cells to replace at the end of useful life

Last Answer : Answer: C

Which of the following statements describes what will occur if the motor shown in the illustration is required to carry 150% of full load? EL-0056 A. The primary counter emf will be increased. B. The stator current will increase. C. The slip will decrease. D. The slip value, stator current curve, and torque curve will all coincide.

Description : Which of the following statements describes what will occur if the motor shown in the illustration is required to carry 150% of full load? EL-0056 A. The primary counter emf will be increased. B. ... slip will decrease. D. The slip value, stator current curve, and torque curve will all coincide.

Last Answer : Answer: B

An increase in the amount of current flow through the armature of a shunt motor is the final result of a/an _____________. A. increase in the load on the motor B. decrease in the load on the motor C. increase in counter EMF D. decrease in armature torque

Description : An increase in the amount of current flow through the armature of a shunt motor is the final result of a/an _____________. A. increase in the load on the motor B. decrease in the load on the motor C. increase in counter EMF D. decrease in armature torque

Last Answer : Answer: A

Which of the following statements is true concerning the operating characteristics of a squirrel-cage motor? A. Rotor slip is dependent upon the motor load. B. An increase in motor load results in less slip. C. A decrease in rotor speed results in less generated current. D. A decrease in rotor speed produces a weaker magnetic field.

Description : Which of the following statements is true concerning the operating characteristics of a squirrel-cage motor? A. Rotor slip is dependent upon the motor load. B. An increase in motor load results in ... results in less generated current. D. A decrease in rotor speed produces a weaker magnetic field.

Last Answer : Answer: A

As the tube filaments in the load heat up, will the circuit current increase or decrease?

Description : As the tube filaments in the load heat up, will the circuit current increase or decrease?

Last Answer : Decrease.

A synchronous motor is operating on no-load at unity power factor. If the field current is increased, power factor will become (A) Leading & current will decrease (B) Lagging & current will increase. (C) Lagging & current will decrease. (D) Leading & current will increase.

Description : A synchronous motor is operating on no-load at unity power factor. If the field current is increased, power factor will become (A) Leading & current will decrease (B) Lagging & current will increase. (C) Lagging & current will decrease. (D) Leading & current will increase.

Last Answer : Ans: A Initially synchronous motor is operating at no load and unity power factor. When field current increases, the excitation will increase. Therefore, p.f will be leading and current will be I CosΦ < I

Why is it advisable not to draw current for many appliances from a single point? (a) Current will decrease (b) Current will increase (c) Current and voltage both will increase (d) Voltage will decrease whereas current will increase

Description : Why is it advisable not to draw current for many appliances from a single point? (a) Current will decrease (b) Current will increase (c) Current and voltage both will increase (d) Voltage will decrease whereas current will increase

Last Answer : Ans:(d)

What is the function of a fuse wire? (a) To prevent an unduly high electric current from passing through a circuit (b) To increase the current supply (c) To decrease the current supply (d) To stabilise the voltage

Description : What is the function of a fuse wire? (a) To prevent an unduly high electric current from passing through a circuit (b) To increase the current supply (c) To decrease the current supply (d) To stabilise the voltage

Last Answer : Ans:(a)

The purpose of choke in a fluorescent lamp is – (1) to increase the current flow (2) to decrease the current flow (3) to decrease the resistance (4) to decrease the voltage momentarily

Description : The purpose of choke in a fluorescent lamp is – (1) to increase the current flow (2) to decrease the current flow (3) to decrease the resistance (4) to decrease the voltage momentarily

Last Answer : (2) to decrease the current flow Explanation: The choke primarily serves to limit current flow to the correct level for the tube. It also can be used during startup to provide an inductive 'kick' forming a momentary highervoltage pulse to start the lamp.

When shipboard electrical distribution circuits are connected in parallel, additional parallel circuits will cause the total circuit resistance to _____________. A. increase, causing a drop in the line current B. increase, causing a decrease in the line voltage C. decrease, causing an increase in the line voltage D. decrease, causing an increase in the line current

Description : When shipboard electrical distribution circuits are connected in parallel, additional parallel circuits will cause the total circuit resistance to _____________. A. increase, causing a drop in the line current B ... an increase in the line voltage D. decrease, causing an increase in the line current

Last Answer : Answer: D

Decreasing the frequency in a capacitive circuit while maintaining a constant circuit voltage, will result in a/an _____________. A. increase in apparent power B. decrease in circuit current C. decrease in capacitive reactance D. decrease in total impedance

Description : Decreasing the frequency in a capacitive circuit while maintaining a constant circuit voltage, will result in a/an _____________. A. increase in apparent power B. decrease in circuit current C. decrease in capacitive reactance D. decrease in total impedance

Last Answer : Answer: B