As the tube filaments in the load heat up, will the circuit current increase or decrease?

As the tube filaments in the load heat up, will the circuit  current increase or decrease?
by

1 Answer

Answer :

Decrease.
by

Related questions

Moving tube electrodes apart to decrease interelectrode capacitance causes an increase in the effect of what property?

Description : Moving tube electrodes apart to decrease interelectrode capacitance causes an increase in the effect of what property?

Last Answer : Transit time

In a co-current double pipe heat exchanger used for condensing saturated steam over the inner tube, if the entrance and exit conditions of the coolant are interchanged, then the rate of condensation will (A) Increase (B) Decrease (C) Remain unchanged (D) Either increase or decrease; depends on the coolant flow rate

Description : In a co-current double pipe heat exchanger used for condensing saturated steam over the inner tube, if the entrance and exit conditions of the coolant are interchanged, then the rate of condensation ... Decrease (C) Remain unchanged (D) Either increase or decrease; depends on the coolant flow rate

Last Answer : (C) Remain unchanged

Does a filter circuit increase or decrease the average output voltage?

Description : Does a filter circuit increase or decrease the average output voltage?

Last Answer : A filter circuit increases the average output voltage

Does a filter circuit increase or decrease the average output voltage?

Description : Does a filter circuit increase or decrease the average output voltage?

Last Answer : Increase.

Select the correct statement regarding the specific disorder of muscular or skeletal system. (a) Muscular dystrophy – Age related shortening of muscles (b) Osteoporosis – Decrease in bone mass and higher chances of fractures with advancing age (c) Myasthenia gravis – Autoimmune disorder which inhibits sliding of myosin filaments (d) Gout – Inflammation of joints due to extra deposition of calcium

Description : Select the correct statement regarding the specific disorder of muscular or skeletal system. (a) Muscular dystrophy - Age related shortening of muscles (b) Osteoporosis - Decrease in bone mass and ... of myosin filaments (d) Gout - Inflammation of joints due to extra deposition of calcium

Last Answer : (b) Osteoporosis – Decrease in bone mass and higher chances of fractures with advancing age

. If a single tube pass heat exchanger is converted to two pass, then for the same flow rate, the pressure drop per unit length in tube side will (A) Increase by 1.8 times (B) Decrease by 2 2 (C) Increase by 2 16 (D) Remain unchanged

Description : . If a single tube pass heat exchanger is converted to two pass, then for the same flow rate, the pressure drop per unit length in tube side will (A) Increase by 1.8 times (B) Decrease by 2 2 (C) Increase by 2 16 (D) Remain unchanged

Last Answer : (C) Increase by 2 16

In case of a multipass shell and tube heat exchanger, providing a baffle on the shell side __________ the heat transfer rate. (A) Increases (B) Decreases (C) Does not affect (D) May increase or decrease, depends on the type of baffle

Description : In case of a multipass shell and tube heat exchanger, providing a baffle on the shell side __________ the heat transfer rate. (A) Increases (B) Decreases (C) Does not affect (D) May increase or decrease, depends on the type of baffle

Last Answer : (A) Increases

Baffles in the shell side of a shell and tube heat exchanger (A) Increase the cross-section of the shell side liquid (B) Force the liquid to flow parallel to the bank (C) Increase the shell side heat transfer co-efficient (D) Decrease the shell side heat transfer co-efficient

Description : Baffles in the shell side of a shell and tube heat exchanger (A) Increase the cross-section of the shell side liquid (B) Force the liquid to flow parallel to the bank (C) Increase the shell side heat transfer co-efficient (D) Decrease the shell side heat transfer co-efficient

Last Answer : (C) Increase the shell side heat transfer co-efficient

In case of vertical tube evaporator, with increase in liquor level, the overall heat transfer co-efficient (A) Increases (B) Decreases (C) Is not affected (D) May increase or decrease; depends on the feed

Description : In case of vertical tube evaporator, with increase in liquor level, the overall heat transfer co-efficient (A) Increases (B) Decreases (C) Is not affected (D) May increase or decrease; depends on the feed

Last Answer : (B) Decreases

Will dark current increase or decrease as the temperature of the photodiode increases?

Description : Will dark current increase or decrease as the temperature of the photodiode increases?

Last Answer : Increase.

A tube has a transconductance of 800 mhos and a load resistor of 50 kohms. When control grid voltage varies by 6 volts, the plate voltage will vary by what amount?

Description : A tube has a transconductance of 800 mhos and a load resistor of 50 kohms. When control grid voltage varies by 6 volts, the plate voltage will vary by what amount?

Last Answer : 240 volts.

What circuit functions does the tube in a gated-beam detector serve?

Description : What circuit functions does the tube in a gated-beam detector serve?

Last Answer : Limits, detects, and amplifies.

Which of the following statements describes what will occur if the motor shown in the illustration is required to carry 150% of full load? EL-0056 A. The primary counter emf will be increased. B. The stator current will increase. C. The slip will decrease. D. The slip value, stator current curve, and torque curve will all coincide.

Description : Which of the following statements describes what will occur if the motor shown in the illustration is required to carry 150% of full load? EL-0056 A. The primary counter emf will be increased. B. ... slip will decrease. D. The slip value, stator current curve, and torque curve will all coincide.

Last Answer : Answer: B

An increase in the amount of current flow through the armature of a shunt motor is the final result of a/an _____________. A. increase in the load on the motor B. decrease in the load on the motor C. increase in counter EMF D. decrease in armature torque

Description : An increase in the amount of current flow through the armature of a shunt motor is the final result of a/an _____________. A. increase in the load on the motor B. decrease in the load on the motor C. increase in counter EMF D. decrease in armature torque

Last Answer : Answer: A

Which of the following statements is true concerning the operating characteristics of a squirrel-cage motor? A. Rotor slip is dependent upon the motor load. B. An increase in motor load results in less slip. C. A decrease in rotor speed results in less generated current. D. A decrease in rotor speed produces a weaker magnetic field.

Description : Which of the following statements is true concerning the operating characteristics of a squirrel-cage motor? A. Rotor slip is dependent upon the motor load. B. An increase in motor load results in ... results in less generated current. D. A decrease in rotor speed produces a weaker magnetic field.

Last Answer : Answer: A

Increasing the load to the secondary windings of a transformer will cause a/an ____________. A. decrease in the primary voltage B. increase in the primary voltage C. decrease in the primary current D. increase in the primary current

Description : Increasing the load to the secondary windings of a transformer will cause a/an ____________. A. decrease in the primary voltage B. increase in the primary voltage C. decrease in the primary current D. increase in the primary current

Last Answer : Answer: D

With an almost discharged battery there will be: a. A decrease of voltage with increasing load b. Increase of current with decrease of voltage c. Decrease of current with increasing load d. Increase of voltage with increasing load

Description : With an almost discharged battery there will be: a. A decrease of voltage with increasing load b. Increase of current with decrease of voltage c. Decrease of current with increasing load d. Increase of voltage with increasing load

Last Answer : a. A decrease of voltage with increasing load

A synchronous motor is operating on no-load at unity power factor. If the field current is increased, power factor will become (A) Leading & current will decrease (B) Lagging & current will increase. (C) Lagging & current will decrease. (D) Leading & current will increase.

Description : A synchronous motor is operating on no-load at unity power factor. If the field current is increased, power factor will become (A) Leading & current will decrease (B) Lagging & current will increase. (C) Lagging & current will decrease. (D) Leading & current will increase.

Last Answer : Ans: A Initially synchronous motor is operating at no load and unity power factor. When field current increases, the excitation will increase. Therefore, p.f will be leading and current will be I CosΦ < I

The end of the usefulness of a tr tube is indicated by an increase in what quantity?

Description : The end of the usefulness of a tr tube is indicated by an increase in what quantity?

Last Answer : Recovery time.

Name the components which greatly increase the weight of vacuum-tube circuitry.

Description : Name the components which greatly increase the weight of vacuum-tube circuitry.

Last Answer : Transformers, capacitors, and resistors.

What is the function of a fuse wire? (a) To prevent an unduly high electric current from passing through a circuit (b) To increase the current supply (c) To decrease the current supply (d) To stabilise the voltage

Description : What is the function of a fuse wire? (a) To prevent an unduly high electric current from passing through a circuit (b) To increase the current supply (c) To decrease the current supply (d) To stabilise the voltage

Last Answer : Ans:(a)

When shipboard electrical distribution circuits are connected in parallel, additional parallel circuits will cause the total circuit resistance to _____________. A. increase, causing a drop in the line current B. increase, causing a decrease in the line voltage C. decrease, causing an increase in the line voltage D. decrease, causing an increase in the line current

Description : When shipboard electrical distribution circuits are connected in parallel, additional parallel circuits will cause the total circuit resistance to _____________. A. increase, causing a drop in the line current B ... an increase in the line voltage D. decrease, causing an increase in the line current

Last Answer : Answer: D

Decreasing the frequency in a capacitive circuit while maintaining a constant circuit voltage, will result in a/an _____________. A. increase in apparent power B. decrease in circuit current C. decrease in capacitive reactance D. decrease in total impedance

Description : Decreasing the frequency in a capacitive circuit while maintaining a constant circuit voltage, will result in a/an _____________. A. increase in apparent power B. decrease in circuit current C. decrease in capacitive reactance D. decrease in total impedance

Last Answer : Answer: B

A transformer in an electric circuit serves to ____________. A. generate its own electrical power B. transform electrical energy into mechanical energy C. increase or decrease circuit voltage as required D. convert AC current to DC current

Description : A transformer in an electric circuit serves to ____________. A. generate its own electrical power B. transform electrical energy into mechanical energy C. increase or decrease circuit voltage as required D. convert AC current to DC current

Last Answer : Answer: C

Why should a resistance be introduced in a circuit in series deliberately? a. to increase current b. to decrease current c. to control current d. just to give a good look to circuit

Description : Why should a resistance be introduced in a circuit in series deliberately? a. to increase current b. to decrease current c. to control current d. just to give a good look to circuit

Last Answer : b. to decrease current

When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease (which one) in the resistance of the regulating device.

Description : When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease (which one) in the resistance of the regulating device.

Last Answer : An increase.

If the impedance of the choke is increased, will the ripple amplitude increase or decrease?

Description : If the impedance of the choke is increased, will the ripple amplitude increase or decrease?

Last Answer : Decrease.

If you increase the value of the capacitor, will the XC increase or decrease? Why?

Description : If you increase the value of the capacitor, will the XC increase or decrease? Why?

Last Answer : It will decrease. Capacitance is inversely proportional to:

If the inductance of a choke-input filter is increased, will the output ripple voltage amplitude (Er) increase or decrease?

Description : If the inductance of a choke-input filter is increased, will the output ripple voltage amplitude (Er) increase or decrease?

Last Answer : Decrease.

When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease in the resistance of the regulating device.

Description : When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease in the resistance of the regulating device.

Last Answer : Increase.

If you increase the value of the capacitor will the XC increase or decrease? Why?

Description : If you increase the value of the capacitor will the XC increase or decrease? Why?

Last Answer : Decrease-Capacitance is inversely proportional to XC.

Will fiber coupling loss generally increase or decrease if the mode field diameter of a single mode fiber is decreased?

Description : Will fiber coupling loss generally increase or decrease if the mode field diameter of a single mode fiber is decreased?

Last Answer : Increase.

The number of modes propagated in a multimode fiber depends on core size and numerical aperture (NA). If the core size and the NA decrease, will the number of modes propagated increase or decrease?

Description : The number of modes propagated in a multimode fiber depends on core size and numerical aperture (NA). If the core size and the NA decrease, will the number of modes propagated increase or decrease?

Last Answer : Decrease.

The fiber's normalized frequency (V) determines how many modes a fiber can support. As the value of V increases, will the number of modes supported by the fiber increase or decrease?

Description : The fiber's normalized frequency (V) determines how many modes a fiber can support. As the value of V increases, will the number of modes supported by the fiber increase or decrease?

Last Answer : Increase.

The purpose of a heat sink, as frequently used with transistors, is to ____________. A. prevent excessive temperature rise B. compensate for excessive doping C. increase the reverse current D. decrease the forward current

Description : The purpose of a heat sink, as frequently used with transistors, is to ____________. A. prevent excessive temperature rise B. compensate for excessive doping C. increase the reverse current D. decrease the forward current

Last Answer : Answer: A

A triode amplifier similar to the one shown in figure 1-19 has an Ebb -conditions, 1.5 milliamperes of current conducts through the tube. What w

Description : A triode amplifier similar to the one shown in figure 1-19 has an Ebb -conditions, 1.5 milliamperes of current conducts through the tube. What w

Last Answer : +275 volts

Reynolds number for water flow through a tube of I.D. 5 cm is 1500. If a liquid of 5 centipoise viscosity and 0.8 specific gravity flows in the same pipe at the same velocity, then the pressure drop will (A) Increase (B) Decrease (C) Remain same (D) Data insufficient to predict pressure drop

Description : Reynolds number for water flow through a tube of I.D. 5 cm is 1500. If a liquid of 5 centipoise viscosity and 0.8 specific gravity flows in the same pipe at the same velocity, then the pressure drop will (A) Increase (B) Decrease (C) Remain same (D) Data insufficient to predict pressure drop

Last Answer : (A) Increase

With an increase in size of tube, the rise or depression of liquid in the tube due to surface tension will (A) Decrease (B) Increase (C) Remain unchanged (D) Depend upon the characteristics of liquid

Description : With an increase in size of tube, the rise or depression of liquid in the tube due to surface tension will (A) Decrease (B) Increase (C) Remain unchanged (D) Depend upon the characteristics of liquid

Last Answer : Answer: Option A

The rise or depression of liquid in a tube due to surface tension will increase in size of tube will (A) Increase (B) Remain unaffected (C) May increase or decrease depending on the characteristics of liquid (D) Decrease

Description : The rise or depression of liquid in a tube due to surface tension will increase in size of tube will (A) Increase (B) Remain unaffected (C) May increase or decrease depending on the characteristics of liquid (D) Decrease

Last Answer : Answer: Option D

What name is given to a resistor used to replace the normal load in a circuit?

Description : What name is given to a resistor used to replace the normal load in a circuit?

Last Answer : Dummy load or dummy antenna.

what part of the circuit is the (a) load and (b) source?

Description : what part of the circuit is the (a) load and (b) source?

Last Answer : a) DS1, the flashlight bulb (b) BAT, the dry cell

When securing an AC generator, you should FIRST ___________. A. open the generator circuit breaker B. switch the voltage regulator to 'manual' C. decrease the field excitation to minimum D. reduce the load on the unit

Description : When securing an AC generator, you should FIRST ___________. A. open the generator circuit breaker B. switch the voltage regulator to 'manual' C. decrease the field excitation to minimum D. reduce the load on the unit

Last Answer : Answer: D

Finned tube heat exchangers (A) Give larger area per tube (B) Use metal fins of low thermal conductivity (C) Facilitate very large temperature drop through tube wall (D) Are used for smaller heat load

Description : Finned tube heat exchangers (A) Give larger area per tube (B) Use metal fins of low thermal conductivity (C) Facilitate very large temperature drop through tube wall (D) Are used for smaller heat load

Last Answer : (A) Give larger area per tube

Multipass heat exchangers are used (A) Because of simplicity of fabrication (B) For low heat load (C) To obtain higher heat transfer co-efficient and shorter tube (D) To reduce the pressure drop

Description : Multipass heat exchangers are used (A) Because of simplicity of fabrication (B) For low heat load (C) To obtain higher heat transfer co-efficient and shorter tube (D) To reduce the pressure drop

Last Answer : (C) To obtain higher heat transfer co-efficient and shorter tube

For the same heat load and mass flow rate in the tube side of a shell and tube heat exchanger, one may use multipass on the tube side, because it (A) Decreases the pressure drop (B) Decreases the outlet temperature of cooling medium (C) Increases the overall heat transfer coefficient (D) None of these

Description : For the same heat load and mass flow rate in the tube side of a shell and tube heat exchanger, one may use multipass on the tube side, because it (A) Decreases the pressure drop (B) ... the outlet temperature of cooling medium (C) Increases the overall heat transfer coefficient (D) None of these

Last Answer : (C) Increases the overall heat transfer coefficient

A concentric double pipe heat exchanger as compared to the shell and tube heat exchanger for the same heat load requires (A) Less heating surface (B) More space (C) Lower maintenance cost (D) None of these

Description : A concentric double pipe heat exchanger as compared to the shell and tube heat exchanger for the same heat load requires (A) Less heating surface (B) More space (C) Lower maintenance cost (D) None of these

Last Answer : (B) More space

The purpose of providing expansion bellows in the shell of tubular exchanger is to (A) Increase the heating load (B) Impart structural strength(C) Account for the uneven expansion of shell and tube bundles(D) Facilitate increase of shell length, if needed

Description : The purpose of providing expansion bellows in the shell of tubular exchanger is to (A) Increase the heating load (B) Impart structural strength (C) Account for the uneven expansion of shell and tube bundles (D) Facilitate increase of shell length, if needed

Last Answer : (C) Account for the uneven expansion of shell and tube bundles

Cytoskeleton is made up of (a) callose deposits (b) cellulosic microfibrils (c) proteinaceous filaments (d) calcium carbonate granules.

Description : Cytoskeleton is made up of (a) callose deposits (b) cellulosic microfibrils (c) proteinaceous filaments (d) calcium carbonate granules.

Last Answer : (c) proteinaceous filaments

The solid linear cytoskeletal elements having a diameter of 6 nm and made up of a single type of monomer are known as (a) microtubules (b) microfilaments (c) intermediate filaments (d) lamins.

Description : The solid linear cytoskeletal elements having a diameter of 6 nm and made up of a single type of monomer are known as (a) microtubules (b) microfilaments (c) intermediate filaments (d) lamins.

Last Answer : (b) microfilaments