What tool is used to set contact clearances on a relay?

What tool is used to set contact clearances on a relay?
by

1 Answer

Answer :

A point bender
by

Related questions

As shown in the illustration, once the "LV" relay is energized for operation, what contacts must remain closed to maintain the "LV" relay energized when the control lever is moved away from the "off" or "stop" position? A. "DBa" contact. B. Reset contacts. C. Upper set of "LVa" contacts. D. Lower set of "LVa" contacts.

Description : As shown in the illustration, once the "LV" relay is energized for operation, what contacts must remain closed to maintain the "LV" relay energized when the control lever is moved away from the "off" or "stop" ... . B. Reset contacts. C. Upper set of "LVa" contacts. D. Lower set of "LVa" contacts.

Last Answer : Answer: C

As shown in the illustration, what is responsible for maintaining the "LV" relay energized when the master switch handle is moved away from the "off" position? EL-0102 A. "DBa" contact. B. Reset contacts. C. Upper set of "LVa" contacts. D. Lower set of "LVa" contacts.

Description : As shown in the illustration, what is responsible for maintaining the "LV" relay energized when the master switch handle is moved away from the "off" position? EL-0102 A. "DBa" contact. B. Reset contacts. C. Upper set of "LVa" contacts. D. Lower set of "LVa" contacts.

Last Answer : Answer: C

What are the different electrical clearances in Substation?

Description : What are the different electrical clearances in Substation?

Last Answer : Ground Clearance: This is the minimum distance between any live conductor and the earth or ground. Phase Clearance: It is the clearance between the different phases in a circuit or same phases in different ... The limits of work section may be ground or the platform on which the person is working.

Tube pitch is the __________ of tube diameters and the clearances. (A) Sum (B) Difference (C) Ratio (D) None of these

Description : Tube pitch is the __________ of tube diameters and the clearances. (A) Sum (B) Difference (C) Ratio (D) None of these

Last Answer : (A) Sum

Name the portal which is an environmental single window hub for Environment, Forest, Wildlife and other clearances launched by Ministry of Environment, Forest and Climate Change (MOEFCC)? a. UNATTI b. NIVARAN c. PAHAL d. PARIVESH

Description : Name the portal which is an environmental single window hub for Environment, Forest, Wildlife and other clearances launched by Ministry of Environment, Forest and Climate Change (MOEFCC)? a. UNATTI b. NIVARAN c. PAHAL d. PARIVESH

Last Answer : d. PARIVESH

Name the portal which is an environmental single window hub for Environment, Forest, Wildlife and other clearances launched by Ministry of Environment, Forest and Climate Change (MOEFCC)? a. UNATTI b. NIVARAN c. PAHAL d. PARIVESH

Description : Name the portal which is an environmental single window hub for Environment, Forest, Wildlife and other clearances launched by Ministry of Environment, Forest and Climate Change (MOEFCC)? a. UNATTI b. NIVARAN c. PAHAL d. PARIVESH

Last Answer : d. PARIVESH

The minimum and maximum clearances of check rails at all BG level crossings shall be a) 51 to 57 mm* b) 44 to 48 mm c) 41 to 45 mm d) 55 to 70 mm

Description : The minimum and maximum clearances of check rails at all BG level crossings shall be a) 51 to 57 mm* b) 44 to 48 mm c) 41 to 45 mm d) 55 to 70 mm

Last Answer : a) 51 to 57 mm*

On B.G. maximum clearances of check rails at a level crossing are (a) 51 mm (b) 57mm* (c) 65mm (d) 70mm

Description : On B.G. maximum clearances of check rails at a level crossing are (a) 51 mm (b) 57mm* (c) 65mm (d) 70mm

Last Answer : (b) 57mm*

On B.G. maximum clearances of check rails at a level crossing are (a) 51mm ( b ) 57mm* (c) 65mm (d) 54mm

Description : On B.G. maximum clearances of check rails at a level crossing are (a) 51mm ( b ) 57mm* (c) 65mm (d) 54mm

Last Answer : ( b ) 57mm*

Which of the motors for the devices listed below is fitted with an instantaneous overload relay? A. Fan B. Pump C. Winch D. Machine tool

Description : Which of the motors for the devices listed below is fitted with an instantaneous overload relay? A. Fan B. Pump C. Winch D. Machine tool

Last Answer : Answer: C

What type of diagram would be most useful for wiring a relay into a circuit?

Description : What type of diagram would be most useful for wiring a relay into a circuit?

Last Answer : . Terminal diagram.

What is used to clean the contacts of a relay?

Description : What is used to clean the contacts of a relay?

Last Answer : A burnishing tool.

When an operating motor is connected to the controller shown in the illustration, the a path of current flow through the circuit is ____________. EL-0010 A. 'L1', stop button, start button, coil 'CR', 'L2' B. 'L1', stop button, 'CR' and 'M' contacts, 'M' coil, 'OL contacts, the 'CR' coil in parallel, 'L2' C. 'L1', stop button, jog button, 'CR' contact, 'CR' relay, 'L2' D. 'L1', stop button, start button, 'CR' contact, 'M' contact, 'CR' coil, 'L2'

Description : When an operating motor is connected to the controller shown in the illustration, the a path of current flow through the circuit is ____________. EL-0010 A. 'L1', stop button, start button, coil 'CR', 'L2' B. 'L1' ... L2' D. 'L1', stop button, start button, 'CR' contact, 'M' contact, 'CR' coil, 'L2'

Last Answer : Answer: B

The winch shown in the illustration operates in any of the positions with the master switch in the 'lower' direction, but will not 'hoist' in any of the master switch hoist positions. Which of the listed faults could be the cause? EL-0102 A. Master switch contact 'MS3' may have defective springs. B. Contactor '3M' coil could have an open winding. C. Contact '2M' in the power circuit may be badly corroded. D. Series relay 'FR' may be open.

Description : The winch shown in the illustration operates in any of the positions with the master switch in the 'lower' direction, but will not 'hoist' in any of the master switch hoist positions. Which of the listed faults ... '2M' in the power circuit may be badly corroded. D. Series relay 'FR' may be open.

Last Answer : Answer: A

The motor starts when the start button in the illustration is pushed, but stops when the button is released the trouble is _________. EL-0007 A. the incorrect thermal overload coil B. a faulty 'M' coil C. a dirty contact on the Disc.Sw. at 'L3' D. a faulty holding relay contact

Description : The motor starts when the start button in the illustration is pushed, but stops when the button is released the trouble is _________. EL-0007 A. the incorrect thermal overload coil B. a faulty 'M' coil C. a dirty contact on the Disc.Sw. at 'L3' D. a faulty holding relay contact

Last Answer : Answer: D

The small circular symbols to which wire '52N57E' is connected at coordinates '57L' and '57P' shown in the illustration represent ___________________. EL-0100 A. relay contact solder points B. wire wrap connections C. terminal board screws D. switch contact terminals

Description : The small circular symbols to which wire '52N57E' is connected at coordinates '57L' and '57P' shown in the illustration represent ___________________. EL-0100 A. relay contact solder points B. wire wrap connections C. terminal board screws D. switch contact terminals

Last Answer : Answer: C

When troubleshooting a motor controller, all indications are that a relay coil should be energized. If there were no magnetic pull, with rated voltage measured across the coil, the most probable cause would be that the _________________. A. coil is open B. control fuse is open C. auxiliary contact in series with the coil is defective D. relay armature is stuck

Description : When troubleshooting a motor controller, all indications are that a relay coil should be energized. If there were no magnetic pull, with rated voltage measured across the coil, the most probable cause ... open C. auxiliary contact in series with the coil is defective D. relay armature is stuck

Last Answer : Answer: A

If Relay #5 changed contact position grounding the 'auto' input to the 'pitch controller module', pitch control would be effected by the _________________. EL-0095 A. pitch feedback potentiometer B. Engine room thrust split potentiometer C. Engine room thrust lever only D. Bridge thrust lever only

Description : If Relay #5 changed contact position grounding the 'auto' input to the 'pitch controller module', pitch control would be effected by the _________________. EL-0095 A. pitch feedback potentiometer B. Engine room thrust split potentiometer C. Engine room thrust lever only D. Bridge thrust lever only

Last Answer : Answer: B

A loud buzzing noise in an AC controller is probably caused by _____________. A. poor contact with the overload relay B. an incorrectly sized heater C. a broken shading coil D. abnormal starting current

Description : A loud buzzing noise in an AC controller is probably caused by _____________. A. poor contact with the overload relay B. an incorrectly sized heater C. a broken shading coil D. abnormal starting current

Last Answer : Answer: C

During its operation, loud buzzing and resultant welding of contacts of a magnetic relay may be caused by __________. A. overheating of the contactor coil B. low voltage on the operating coil C. low insulation resistance to ground D. lubrication of the contact bearing points

Description : During its operation, loud buzzing and resultant welding of contacts of a magnetic relay may be caused by __________. A. overheating of the contactor coil B. low voltage on the operating coil C. low insulation resistance to ground D. lubrication of the contact bearing points

Last Answer : Answer: B

Overheating of relay contacts or contact born out is due to (a) slow making and breaking of load circuit contacts (b) foreign matter on the contact surface (c) too low contact pressure (d) all of the above

Description : Overheating of relay contacts or contact born out is due to (a) slow making and breaking of load circuit contacts (b) foreign matter on the contact surface (c) too low contact pressure (d) all of the above

Last Answer : (d) all of the above

In order that current should flow without causing excessive heating or voltage drop, the relay contacts should (a) have low contact resistance (b) be clean and smooth (c) be of sufficient size and proper shape (d) have all above properties

Description : In order that current should flow without causing excessive heating or voltage drop, the relay contacts should (a) have low contact resistance (b) be clean and smooth (c) be of sufficient size and proper shape (d) have all above properties

Last Answer : (d) have all above properties

Overheating of relay contacts or contact born out is due to?

Last Answer : Overheating of relay contacts or contact born out is due to slow making and breaking of load circuit contacts, foreign matter on the contact surface, too low contact pressure.

What is the maximum allowable source pressure that can be used with the compressor air/nitrogen heating tool?

Description : What is the maximum allowable source pressure that can be used with the compressor air/nitrogen heating tool?

Last Answer : 200 psig.

What tool should be used to strip aluminum wire?

Description : What tool should be used to strip aluminum wire?

Last Answer : Knife.

What stripping tool would NOT be used to strip glass braid insulation?

Description : What stripping tool would NOT be used to strip glass braid insulation?

Last Answer : Hot-blade stripper.

What tool is used to de-energize capacitors in a circuit that has been disconnected from its power source?

Description : What tool is used to de-energize capacitors in a circuit that has been disconnected from its power source?

Last Answer : Shorting probe.

What is the purpose of the green conductor in a power tool or electrical appliance cable?

Description : What is the purpose of the green conductor in a power tool or electrical appliance cable?

Last Answer : To prevent electrical shock to the operator in case there is an electrical short to the frame of the appliance or too.

What two features make the Huntron Tracker 2000 a widely used troubleshooting tool?

Description : What two features make the Huntron Tracker 2000 a widely used troubleshooting tool?

Last Answer : It eliminates the need for multiple pieces of test equipment and it is lightweight and portable

The beat frequency in a swept-frequency transmitter provides what contact information?

Description : The beat frequency in a swept-frequency transmitter provides what contact information?

Last Answer : Range.

The Doppler variation is directly proportional to what radar contact characteristic?

Description : The Doppler variation is directly proportional to what radar contact characteristic?

Last Answer : Velocity.

Which type of fiber optic connector (butt-jointed or expanded beam) brings the prepared ends of two optical fibers into close contact?

Description : Which type of fiber optic connector (butt-jointed or expanded beam) brings the prepared ends of two optical fibers into close contact?

Last Answer : Butt-jointed connectors.

What is the capacitive reactance across a point-contact diode as compared to a normal junction diode?

Description : What is the capacitive reactance across a point-contact diode as compared to a normal junction diode?

Last Answer : Lower.

During the manufacture of a point-contact diode, what is the purpose of passing a relatively large current from the catwhisker to the silicon crystal?

Description : During the manufacture of a point-contact diode, what is the purpose of passing a relatively large current from the catwhisker to the silicon crystal?

Last Answer : . To form a small region of p-type material

When paralleling two AC generators, the synchroscope selector switch and frequency meter switch should be set up to sense the frequency of the _____________. A. bus B. generator on the line C. oncoming generator D. bus transfer relay

Description : When paralleling two AC generators, the synchroscope selector switch and frequency meter switch should be set up to sense the frequency of the _____________. A. bus B. generator on the line C. oncoming generator D. bus transfer relay

Last Answer : Answer: C

Is it possible for an organization to set up a facebook tool so that after people donate money the donator can share their action on their personal facebook page?

Description : Is it possible for an organization to set up a facebook tool so that after people donate money the donator can share their action on their personal facebook page?

Last Answer : That’s a pretty expensive status update… I kinda doubt Facebook would allow this, unless they got some of the profit.

Does the 3pc. Fiskars Garden Tool set have a replaceable telescopic handle?

Description : Does the 3pc. Fiskars Garden Tool set have a replaceable telescopic handle?

Last Answer : I could not find a replacement handle for the Fiskars Garden Tool set.

Can you replace the razor blade that is in the razor knife that is included with the Evolv 10 pc. Homeowner Tool Set ?

Description : Can you replace the razor blade that is in the razor knife that is included with the Evolv 10 pc. Homeowner Tool Set ?

Last Answer : Yes the blade is easy to replace.

On what range should you set the voltmeter prior to taking a voltage measurement?

Description : On what range should you set the voltmeter prior to taking a voltage measurement?

Last Answer : Highest.

What should you do with a synchro that has a bad set of bearings?

Description : What should you do with a synchro that has a bad set of bearings?

Last Answer : Replace it.

What is the output voltage of a CT when it is set on electrical zero?

Description : What is the output voltage of a CT when it is set on electrical zero?

Last Answer : Zero or minimum voltage.

What should a voltmeter read when a TX is set on coarse zero?

Description : What should a voltmeter read when a TX is set on coarse zero?

Last Answer : Approximately 37 volts.

What connections in a TDR system are reversed to set up the system for addition?

Description : What connections in a TDR system are reversed to set up the system for addition?

Last Answer : . The R1 and R3 leads between the TDR rotor and the TX to which it is connected.

What connections in a TDX system are reversed to set up the system for addition?

Description : What connections in a TDX system are reversed to set up the system for addition?

Last Answer : The number and type of synchro receivers, the mechanical loads on these receivers and the operating temperatures of both the transmitter and receivers.

When measuring receiver sensitivity, what quantities must you add to the dBm reading obtained on the signal generator or test set?

Description : When measuring receiver sensitivity, what quantities must you add to the dBm reading obtained on the signal generator or test set?

Last Answer : Attenuations of the directional coupler and the connecting cable.

In addition to recovery time, what determines the minimum range of a radar set?

Description : In addition to recovery time, what determines the minimum range of a radar set?

Last Answer : Pulse width

The distance from a radar set to a target measured along the line of sight is identified by what term?

Description : The distance from a radar set to a target measured along the line of sight is identified by what term?

Last Answer : Range.