What is the output voltage of a CT when it is set on electrical zero?

What is the output voltage of a CT when it is set on  electrical zero?
by

1 Answer

Answer :

Zero or minimum voltage.
by

Related questions

What is the amplitude and voltage induced into the rotor when the CX is turned 90º while the CT remains on electrical zero?

Description : What is the amplitude and voltage induced into the rotor when the CX is turned 90º while the CT remains on electrical zero?

Last Answer : The voltage is maximum and in phase with the ac excitation voltage to the CX.

What is the name given to the electrical output of a CT?

Description : What is the name given to the electrical output of a CT?

Last Answer : Error signal

When a CT is on electrical zero, what is the relationship between its rotor and the S2 winding?

Description : When a CT is on electrical zero, what is the relationship between its rotor and the S2 winding?

Last Answer : They are perpendicular to each other.

In a control synchro system, when is the output of the CT reduced to zero?

Description : In a control synchro system, when is the output of the CT reduced to zero?

Last Answer : When the CX and CT rotors are in correspondence.

What three things prevent a CT rotor from turning when voltages are applied to its stator windings?

Description : What three things prevent a CT rotor from turning when voltages are applied to its stator windings?

Last Answer : The rotor is specially wound, it is never connected to an ac supply, and its output is always applied to a high-impedance load.

An error signal is the difference between what two quantities fed to the CT (error detector)?

Description : An error signal is the difference between what two quantities fed to the CT (error detector)?

Last Answer : Input signal and feedback.

Which quantity (voltage or current) determines the intensity of an electrical shock?

Description : Which quantity (voltage or current) determines the intensity of an electrical shock?

Last Answer : Current.

If a voltage (positive or negative) is measured on the "1" output of a flip-flop, what state is it in?

Description : If a voltage (positive or negative) is measured on the "1" output of a flip-flop, what state is it in?

Last Answer : SET state.

What would be the output of a negative clamper with a bias potential of −5 volts and an input voltage swing from +50 to −50 volts?

Description : What would be the output of a negative clamper with a bias potential of −5 volts and an input voltage swing from +50 to −50 volts?

Last Answer : -5 volts.

In a full-wave voltage doubler, are the capacitors connected in series or in parallel with the output load?

Description : In a full-wave voltage doubler, are the capacitors connected in series or in parallel with the output load?

Last Answer : In parallel.

When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease (which one) in the resistance of the regulating device.

Description : When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease (which one) in the resistance of the regulating device.

Last Answer : An increase.

The purpose of a voltage regulator is to provide an output voltage with little or no __

Description : The purpose of a voltage regulator is to provide an output voltage with little or no __

Last Answer : Variation.

Does a filter circuit increase or decrease the average output voltage?

Description : Does a filter circuit increase or decrease the average output voltage?

Last Answer : A filter circuit increases the average output voltage

What is the average voltage (Eavg) Output of a full-wave rectifier with an output of 100 volts peak?

Description : What is the average voltage (Eavg) Output of a full-wave rectifier with an output of 100 volts peak?

Last Answer : 63.7 volts.

If the output of a half-wave rectifier is 50-volts peak, what is the average voltage

Description : If the output of a half-wave rectifier is 50-volts peak, what is the average voltage

Last Answer : 15.9 volts.

What characteristic is determined by the time required for a voltage wave to travel from the input end of an artificial transmission line to the output end and back again?

Description : What characteristic is determined by the time required for a voltage wave to travel from the input end of an artificial transmission line to the output end and back again?

Last Answer : Pulse width

What characteristic is determined by the time required for a voltage wave to travel from the input end of an artificial transmission line to the output end and back again?

Description : What characteristic is determined by the time required for a voltage wave to travel from the input end of an artificial transmission line to the output end and back again?

Last Answer : Pulse width.

The purpose of a voltage regulator is to provide an output voltage with little or no _

Description : The purpose of a voltage regulator is to provide an output voltage with little or no _

Last Answer : Variation.

What two factors can cause output dc voltage to change?

Description : What two factors can cause output dc voltage to change?

Last Answer : Ac line voltage and a change in load resistance.

If the inductance of a choke-input filter is increased, will the output ripple voltage amplitude (Er) increase or decrease?

Description : If the inductance of a choke-input filter is increased, will the output ripple voltage amplitude (Er) increase or decrease?

Last Answer : Decrease.

When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease in the resistance of the regulating device.

Description : When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease in the resistance of the regulating device.

Last Answer : Increase.

Does a filter circuit increase or decrease the average output voltage?

Description : Does a filter circuit increase or decrease the average output voltage?

Last Answer : Increase.

What is the average voltage (Eavg) output of a full-wave rectifier that has an output of 100 volts peak?

Description : What is the average voltage (Eavg) output of a full-wave rectifier that has an output of 100 volts peak?

Last Answer : 63.6 volts.

Why does using ac vice dc bias voltage result in a stronger output signal?

Description : Why does using ac vice dc bias voltage result in a stronger output signal?

Last Answer : Because an ac bias voltage of the proper frequency and level places the input signal away from both steps in the magnetism curve. The result is two undistorted output signals that are combined into one strong output.

What component causes a generator to produce dc voltage rather than ac voltage at its output terminals?

Description : What component causes a generator to produce dc voltage rather than ac voltage at its output terminals?

Last Answer : A commutator

In signal generators, what device is used to regulate the voltage of the output signal?

Description : In signal generators, what device is used to regulate the voltage of the output signal?

Last Answer : Attenuator.

What is the mathematical formula for computing the output voltage from a moving coil in a magnetic field?

Description : What is the mathematical formula for computing the output voltage from a moving coil in a magnetic field?

Last Answer : 8. e = Emax sine θ.

How is output voltage controlled in practical alternators?

Description : How is output voltage controlled in practical alternators?

Last Answer : By varying the voltage applied to the field windings.

The variation in output voltage as the load changes is referred to as what? How is it expressed?

Description : The variation in output voltage as the load changes is referred to as what? How is it expressed?

Last Answer : Voltage regulation. As a percentage.

What is the frequency of the output voltage of an alternator with four poles that is rotated at 3600 rpm?

Description : What is the frequency of the output voltage of an alternator with four poles that is rotated at 3600 rpm?

Last Answer : 120 Hz.

What two factors determine the frequency of the output voltage of an alternator?

Description : What two factors determine the frequency of the output voltage of an alternator?

Last Answer : Speed of rotation and number of poles.

What is the part of an alternator in which the output voltage is generated?

Description : What is the part of an alternator in which the output voltage is generated?

Last Answer : Armature.

On an open-ended transmission line, the voltage is always zero at what distance from each end of the line?

Description : On an open-ended transmission line, the voltage is always zero at what distance from each end of the line?

Last Answer : One-fourth the distance from each end of the line.

What should a voltmeter read when a TX is set on coarse zero?

Description : What should a voltmeter read when a TX is set on coarse zero?

Last Answer : Approximately 37 volts.

But is it advisable to keep the secondary of CT in open conditions? Will not induce very high voltage?

Description : But is it advisable to keep the secondary of CT in open conditions? Will not induce very high voltage?

Last Answer : If the CT has only one secondary winding, we should keep it always short cktd for safety, but if the CT has multiple secondary, then if one secondary voltage is kept limited by suitable loading, then the other secondary voltage is eventually limited proportionately. 

What is over voltage interturn test for CT?

Description : What is over voltage interturn test for CT?

Last Answer : With secondary open, pass rated current in primary for 1 min. Then check secondary for insulation. 

Define knee point voltage of a CT.

Description : Define knee point voltage of a CT.

Last Answer : When the primary of a CT is open circuited and supply (variable) of system frequency is given to secondary, then a 10% increase in voltage constitutes 50% increase in current. That voltage is the knee point ... Above kpv the ratio of transformer will not be applicable. kpv = RCT + RLEADS + RRELAY  

On what range should you set the voltmeter prior to taking a voltage measurement?

Description : On what range should you set the voltmeter prior to taking a voltage measurement?

Last Answer : Highest.

The output from a full wave rectifier is (a) A pulsating uni-directional current (b) A DC voltage (c) Zero (d) An AC voltage

Description : The output from a full wave rectifier is (a) A pulsating uni-directional current (b) A DC voltage (c) Zero (d) An AC voltage

Last Answer : a) A pulsating uni-directional current

To remove an alternator operating in parallel with another unit from the main electrical bus, you must FIRST _________. A. adjust the power factor on both units B. set the desired voltage on the outgoing alternator C. open the circuit breaker on the outgoing alternator D. remove the load from the outgoing alternator

Description : To remove an alternator operating in parallel with another unit from the main electrical bus, you must FIRST _________. A. adjust the power factor on both units B. set the desired voltage on ... C. open the circuit breaker on the outgoing alternator D. remove the load from the outgoing alternator

Last Answer : Answer: D

What type of flux must be used in all electrical and electronic soldering?

Description : What type of flux must be used in all electrical and electronic soldering?

Last Answer : Noncorrosive, nonconductive rosin fluxes.

What is the tin-lead alloy percentage of solder used for electrical connectors, splices, and terminal lugs?

Description : What is the tin-lead alloy percentage of solder used for electrical connectors, splices, and terminal lugs?

Last Answer : 60-percent tin and 40-percent lead (60/40 solder).

When working on electrical equipment, why should you use only one hand?

Description : When working on electrical equipment, why should you use only one hand?

Last Answer : . To minimize the probability of providing a path for current through your body.

Before working on electrical equipment containing capacitors, what should you do to the capacitors?

Description : Before working on electrical equipment containing capacitors, what should you do to the capacitors?

Last Answer : Discharge them by shorting them to ground.

What restrictions are placed on the use of the electrical lock method?

Description : What restrictions are placed on the use of the electrical lock method?

Last Answer : It can be used only if the leads of the synchro are accessible and the rotor is free to turn.

What semiconductor device produces electrical energy when exposed to light?

Description : What semiconductor device produces electrical energy when exposed to light?

Last Answer : Photovoltaic cell.

The varactor displays what useful electrical property?

Description : The varactor displays what useful electrical property?

Last Answer : Variable capacitance.

What type of electrical diagram is used to identify the components of a system?

Description : What type of electrical diagram is used to identify the components of a system?

Last Answer : A pictorial diagram.