What tool should be used to strip aluminum wire?

What tool should be used to strip aluminum wire?
by

1 Answer

Answer :

Knife.
by

Related questions

What stripping tool would NOT be used to strip glass braid insulation?

Description : What stripping tool would NOT be used to strip glass braid insulation?

Last Answer : Hot-blade stripper.

Should aluminum wire be cleaned prior to installing an aluminum terminal lug or splice?

Description : Should aluminum wire be cleaned prior to installing an aluminum terminal lug or splice?

Last Answer : No, it is done automatically by the petroleum abrasive compound that comes in the terminal or splices.

State two advantages of using aluminum wire for carrying electricity over long distances.

Description : State two advantages of using aluminum wire for carrying electricity over long distances.

Last Answer : It is light and reduces corona.

From the following which method is used to guide the AGV. a.Wire guided b.Paint strip c.Self guided vehicle d.All of the above

Description : From the following which method is used to guide the AGV. a.Wire guided b.Paint strip c.Self guided vehicle d.All of the above

Last Answer : d.All of the above

A COPPER strip is placed in one compartment of a voltaic cell and a wire connects this strip to a piece of metal in the other compartment through a voltmeter. If the voltmeter reads zero, the other piece of metal is: w) zinc x) mercury y) silver z) copper

Description : A COPPER strip is placed in one compartment of a voltaic cell and a wire connects this strip to a piece of metal in the other compartment through a voltmeter. If the voltmeter reads zero, the other piece of metal is: w) zinc x) mercury y) silver z) copper

Last Answer : ANSWER: Z -- COPPER

Can you remove tarnish on this aluminum kitchen tool?

Description : Can you remove tarnish on this aluminum kitchen tool?

Last Answer : Take a green Scotchbrite scrubby pad to it. The tarnish is only a few molecules deep, and the green scrubbies are abrasive enough to remove that layer. It will also remove that nice, shiny finish, however

What tool should be used to drive a roll pin from an aluminum component?

Description : What tool should be used to drive a roll pin from an aluminum component?

Last Answer : Feel Free to Answer

Why should a lockwasher never be used with an aluminum terminal?

Description : Why should a lockwasher never be used with an aluminum terminal?

Last Answer : It gouges the terminal lug and causes deterioration.

What tools should be used to install large aluminum terminal lugs and splices?

Description : What tools should be used to install large aluminum terminal lugs and splices?

Last Answer : Power-operated crimping tools.

State four advantages of copper over aluminum as a conductor.

Description : State four advantages of copper over aluminum as a conductor.

Last Answer : It has higher conductivity, it is more ductile, it has relatively high tensile strength, and it can be easily soldered.

How are copper wire and aluminum foil alike?

Description : How are copper wire and aluminum foil alike?

Last Answer : negative charges can't move through them

Fuse wire is made of _____? A. 63% lead arid 37% tin B. 63% tin and 37% aluminum C. 63% tin and 37% lead D. 63% lead and 37% aluminum

Description : Fuse wire is made of _____? A. 63% lead arid 37% tin B. 63% tin and 37% aluminum C. 63% tin and 37% lead D. 63% lead and 37% aluminum

Last Answer : ANSWER: C

Fuse wire is made of _____? A. 63% lead arid 37% tin B. 63% tin and 37% aluminum C. 63% tin and 37% lead D. 63% lead and 37% aluminum

Description : Fuse wire is made of _____? A. 63% lead arid 37% tin B. 63% tin and 37% aluminum C. 63% tin and 37% lead D. 63% lead and 37% aluminum

Last Answer : ANSWER: C

Fuse wire is made of-------? A. 63% tin and 37% lead (Answer) B. 63% lead and 37% tin C. 63% tin and 37% aluminum D. 63% lead and 37% aluminum

Description : Fuse wire is made of-------? A. 63% tin and 37% lead (Answer) B. 63% lead and 37% tin C. 63% tin and 37% aluminum D. 63% lead and 37% aluminum

Last Answer : A. 63% tin and 37% lead (Answer)

What is the maximum allowable source pressure that can be used with the compressor air/nitrogen heating tool?

Description : What is the maximum allowable source pressure that can be used with the compressor air/nitrogen heating tool?

Last Answer : 200 psig.

What tool is used to de-energize capacitors in a circuit that has been disconnected from its power source?

Description : What tool is used to de-energize capacitors in a circuit that has been disconnected from its power source?

Last Answer : Shorting probe.

What is the purpose of the green conductor in a power tool or electrical appliance cable?

Description : What is the purpose of the green conductor in a power tool or electrical appliance cable?

Last Answer : To prevent electrical shock to the operator in case there is an electrical short to the frame of the appliance or too.

What two features make the Huntron Tracker 2000 a widely used troubleshooting tool?

Description : What two features make the Huntron Tracker 2000 a widely used troubleshooting tool?

Last Answer : It eliminates the need for multiple pieces of test equipment and it is lightweight and portable

What tool is used to set contact clearances on a relay?

Description : What tool is used to set contact clearances on a relay?

Last Answer : A point bender

What is an advantage of using a resistance soldering iron when soldering wire to a connector?

Description : What is an advantage of using a resistance soldering iron when soldering wire to a connector?

Last Answer : The soldering tips are hot only during the brief period of soldering the connection, thus minimizing the chance of burning the wire insulation or connector inserts.

What is used to tie wire bundles in high-temperature areas?

Description : What is used to tie wire bundles in high-temperature areas?

Last Answer : High-temperature, pressure-sensitive tape.

What size wire bundles require double lace?

Description : What size wire bundles require double lace?

Last Answer : Bundles that are 1 inch or larger in diameter

Why is flat tape preferred instead of round cord when wire bundles are laced?

Description : Why is flat tape preferred instead of round cord when wire bundles are laced?

Last Answer : Round cord has a tendency to cut into the wire insulation.

Why should wire be stripped 1/32 inch longer than the depth of the solder barrel?

Description : Why should wire be stripped 1/32 inch longer than the depth of the solder barrel?

Last Answer : To prevent burning the insulation during the soldering process and to allow the wire to flex easier at a stress point.

Why are the ends of the wire clamped down after a Western Union splice is made?

Description : Why are the ends of the wire clamped down after a Western Union splice is made?

Last Answer : To prevent damage to the tape insulation.

What is the preferred method for stripping wire?

Description : What is the preferred method for stripping wire?

Last Answer : By use of a wire-stripping tool

The large surface area of a waveguide greatly reduces what type of loss that is common in two-wire and coaxial lines?

Description : The large surface area of a waveguide greatly reduces what type of loss that is common in two-wire and coaxial lines?

Last Answer : Copper loss.

. Why are coaxial lines more efficient at microwave frequencies than two-wire transmission lines?

Description : . Why are coaxial lines more efficient at microwave frequencies than two-wire transmission lines?

Last Answer : The electromagnetic fields are completely confined

What is the purpose of the spring or wire around the leads of a new MOSFET?

Description : What is the purpose of the spring or wire around the leads of a new MOSFET?

Last Answer : To prevent damage from static electricity.

Conduction in which type of semiconductor material is similar to conduction in a copper wire?

Description : Conduction in which type of semiconductor material is similar to conduction in a copper wire?

Last Answer : N-type material.

What type of PN diode is formed by using a fine metal wire and a section of N-type semiconductor material?

Description : What type of PN diode is formed by using a fine metal wire and a section of N-type semiconductor material?

Last Answer : Point-contact.

What safety precaution must you observe when soldering or hot-wire stripping fluoroplastic insulated wire?

Description : What safety precaution must you observe when soldering or hot-wire stripping fluoroplastic insulated wire?

Last Answer : Adequate ventilation.

If a wire passes through a connector what portion of the aircraft wire identification number changes?

Description : If a wire passes through a connector what portion of the aircraft wire identification number changes?

Last Answer : Wire segment letter.

Where would you find the wire identification system for a specific piece of equipment?

Description : Where would you find the wire identification system for a specific piece of equipment?

Last Answer : In the technical manual for the equipment

What are the two primary disadvantages of a two-wire open line?

Description : What are the two primary disadvantages of a two-wire open line?

Last Answer : High radiation losses and noise pickup.

Name two of the three described uses of a two-wire open line.

Description : Name two of the three described uses of a two-wire open line.

Last Answer : Power lines, rural telephone lines, and telegraph lines

What procedure involves the use of finely braided copper wire to remove solder?

Description : What procedure involves the use of finely braided copper wire to remove solder?

Last Answer : Wicking.

Which wire has the least resistance? Wire A-copper, 1000 circular mils, 6 inches long. Wire B-copper, 2000 circular mils, 11 inches long.

Description : Which wire has the least resistance? Wire A-copper, 1000 circular mils, 6 inches long. Wire B-copper, 2000 circular mils, 11 inches long.

Last Answer : Wire B.

What is the purpose of an order-wire circuit?

Description : What is the purpose of an order-wire circuit?

Last Answer : For operator-to-operator service messages and frequency changes.

What is the common name for enamel-insulated wire?

Description : What is the common name for enamel-insulated wire?

Last Answer : Magnet wire.

State why it is important for you to consider the ambient (surrounding) temperature of a conductor when selecting wire size.

Description : State why it is important for you to consider the ambient (surrounding) temperature of a conductor when selecting wire size.

Last Answer : The heat surrounding the conductor is an important part of total conductor heating.

List the four factors you should use to select wire for a specified current rating.

Description : List the four factors you should use to select wire for a specified current rating.

Last Answer : Conductor size, the material it is made of the location of the wiren in a circuit, and the type of insulation used.

When using an American Standard Wire Gauge to determine the size of a wire, where should you place the wire in the gauge to get the correct measurement?

Description : When using an American Standard Wire Gauge to determine the size of a wire, where should you place the wire in the gauge to get the correct measurement?

Last Answer : In the parallel walled slot not the circular area.

Using table 1-2, determine the resistance of 1,500 feet of AWG 20 wire at 25º C.

Description : Using table 1-2, determine the resistance of 1,500 feet of AWG 20 wire at 25º C.

Last Answer : 1,000 ft = 10.4 ohms1,500 ft = 1.5 × 0.4 = 15.6 ohms

To radiate power efficiently, a long-wire antenna must have what minimum overall length?

Description : To radiate power efficiently, a long-wire antenna must have what minimum overall length?

Last Answer : One-half wavelength.

How many voltage outputs are available from a two-phase three-wire alternator?

Description : How many voltage outputs are available from a two-phase three-wire alternator?

Last Answer : Three.

Do you strip away the strings on the outside of celery before eating it?

Description : Do you strip away the strings on the outside of celery before eating it?

Last Answer : Nope. I trim the ends, right below the line where the leaves start, and most of the white part too. But that’s it, then I fill with almond butter.

What’s the best way to deal psychologically with the trauma from being strip searched?

Description : What’s the best way to deal psychologically with the trauma from being strip searched?

Last Answer : Welcome to Fluther. Righteous anger and outrage would be my go-to emotions in this case.

Why have videos started doing this thing where it's only in focus in a vertical strip down the middle?

Description : Why have videos started doing this thing where it's only in focus in a vertical strip down the middle?

Last Answer : That happens when people record their videos vertically. It's really an unacceptable thing to do, and people used to get crucified online for doing it. But it's quite common still. There ... force correct horizontal video. Vertical video is the only possible reason the death penalty should be legal.

Any tricks you have learned about an easy way to strip wallpaper?

Description : Any tricks you have learned about an easy way to strip wallpaper?

Last Answer : answer:I did it 20 years ago and all I remember is I bought a heat gun and a wide scraper from the paint department at the hardware store. The heat gun is 1200 watts, so I’m thinking a hair dryer would probably do the same job. I think they’re typically 1500 watts.