What are two ways that circuit measurement is used?

What are two ways that circuit measurement is used?
by

1 Answer

Answer :

Circuit measurement is used to (1) monitor the operation of a  piece of electrical or electronic equipment and (2) determine the  reason a piece of electrical or electronic equipment is not functioning  properly.
by

Related questions

When taking a voltage measurement, which lead of the voltmeter should you connect to the circuit first?

Description : When taking a voltage measurement, which lead of the voltmeter should you connect to the circuit first?

Last Answer : Ground.

On what range should you set the voltmeter prior to taking a voltage measurement?

Description : On what range should you set the voltmeter prior to taking a voltage measurement?

Last Answer : Highest.

What calibration label is used when actual measurement values must be known to use the test equipment?

Description : What calibration label is used when actual measurement values must be known to use the test equipment?

Last Answer : CALIBRATED—REFER TO REPORT.

What unit of measurement refers to the torque of a synchro transmitter

Description : What unit of measurement refers to the torque of a synchro transmitter

Last Answer : Ounce-inches.

What radar scope uses a range step for range measurement?

Description : What radar scope uses a range step for range measurement?

Last Answer : The A scope.

What is the primary measurement application for tuning forks?

Description : What is the primary measurement application for tuning forks?

Last Answer : They are used to monitor fixed motor speeds.

A transmission line is said to have distributed constants of inductance, capacitance, and resistance along the line. What units of measurement are used to express these constants?

Description : A transmission line is said to have distributed constants of inductance, capacitance, and resistance along the line. What units of measurement are used to express these constants?

Last Answer : Inductance is expressed in micro henrys per unit length, capacitance is expressed in picofarads per unit length, and resistance is expressed in ohms per unit length.

What is the unit of measurement of apparent power?

Description : What is the unit of measurement of apparent power?

Last Answer : Apparent power

What is the unit of measurement of reactive power?

Description : What is the unit of measurement of reactive power?

Last Answer : var.

What is the unit of measurement of true power?

Description : What is the unit of measurement of true power?

Last Answer : var.

When is an optical power meter measurement recommended for conducting field measurements on installed optical fiber cables or cable plants?

Description : When is an optical power meter measurement recommended for conducting field measurements on installed optical fiber cables or cable plants?

Last Answer : When an installed optical fiber cable or cable plant is less than 50 meters in length.

When using an American Standard Wire Gauge to determine the size of a wire, where should you place the wire in the gauge to get the correct measurement?

Description : When using an American Standard Wire Gauge to determine the size of a wire, where should you place the wire in the gauge to get the correct measurement?

Last Answer : In the parallel walled slot not the circular area.

What other measurement can an ohmmeter make?

Description : What other measurement can an ohmmeter make?

Last Answer : Circuit continuity.

What range of an ammeter is selected for the final measurement?

Description : What range of an ammeter is selected for the final measurement?

Last Answer : A range that allows a meter reading near the center of the scale.

Why should you use the highest range of an ammeter for the initial measurement?

Description : Why should you use the highest range of an ammeter for the initial measurement?

Last Answer : To prevent damage to the meter movement from excessive current.

Draw the circuit diagram for:- i) Measurement of active power in 3-phase load circuit using two wattmeter. ii) Measurement of reactive power in 3-phase load circuit using one wattmeter.

Description : Draw the circuit diagram for:- i) Measurement of active power in 3-phase load circuit using two wattmeter. ii) Measurement of reactive power in 3-phase load circuit using one wattmeter.

Last Answer : (i) Measurement of active power in 3- phase load circuit using two- wattmeter: (ii) Measurement of reactive power in 3- phase load circuit using one wattmeter

List any two methods of reactive power measurement in 3 phase circuit.

Description : List any two methods of reactive power measurement in 3 phase circuit.

Last Answer : Methods of reactive power measurement in 3 phase circuit: (i) Two single phase wattmeter method (ii) One single phase wattmeter method

In the measurement of power of balanced load by two wattmeter method in a 3-phase circuit, The readings

Description :  In the measurement of power of balanced load by two wattmeter method in a 3-phase circuit, The readings of the wattmeters are 4 kW and 2 kW respectively, the later is being taken after reversing the connections of current coil. the ... kVAR B) 0.2 & 6 √3 kVAR C) 0.32 & 2 kVAR D) 0.32 & 2 √3 kVAR

Last Answer :  In the measurement of power of balanced load by two wattmeter method in a 3-phase circuit, The readings of the wattmeters are 4 kW and 2 kW respectively, the later is being taken after reversing the ... of current coil. the power factor and reactive power of the load is 0.2 & 6 √3 kVAR

For power measurement of three phase circuit by two wattmeter method, when the value of power factor

Description : For power measurement of three phase circuit by two wattmeter method, when the value of power factor is less than 0.5 lagging:

Last Answer : For power measurement of three phase circuit by two wattmeter method, when the value of power factor is less than 0.5 lagging: One of the wattmeter connections will have to be reversed

When a resistor is used as a shunt and is connected in parallel with a meter movement coil, it will provide _____________. A. a measurement of circuit resistance B. an increased accuracy of approximately 1.5 percent C. an extended meter range D. none of the above

Description : When a resistor is used as a shunt and is connected in parallel with a meter movement coil, it will provide _____________. A. a measurement of circuit resistance B. an increased accuracy of approximately 1.5 percent C. an extended meter range D. none of the above

Last Answer : Answer: C

Draw a neat sketch and explain the use of CT and PT for measurement of power in a single-phase circuit?

Description : Draw a neat sketch and explain the use of CT and PT for measurement of power in a single-phase circuit?

Last Answer : If wattmeter of proper range is not available or if voltage and current ranges are high we can usr CT and PT of suitable ratio. Connect the CT and PT as shown in figure. The reading of wattmeter can be multiplied by the ratio to get the actual power.   

Voltage measurement in a high impedance circuit requires a voltmeter with

Description : Voltage measurement in a high impedance circuit requires a voltmeter with

Last Answer : high input impedance

What is a device that provides a method of sampling energy from within a waveguide for measurement or use in another circuit?

Description : What is a device that provides a method of sampling energy from within a waveguide for measurement or use in another circuit?

Last Answer : Directional Coupler

Sketch DC signal conditioning circuit for pressure measurement using strain gauge. Justify it.

Description : Sketch DC signal conditioning circuit for pressure measurement using strain gauge. Justify it.

Last Answer : Diagram: Figure: DC signal conditioning circuit for pressure measurement using strain gauge Where, Rg= strain gauge resistance. Explanation: In order to measure strain with ... millivolts output per volt input. The Wheatstone circuit is also well suited for temperature compensation.

Describe with neat circuit diagram the measurement procedure of earth resistance for an installation.

Description : Describe with neat circuit diagram the measurement procedure of earth resistance for an installation. 

Last Answer : Following procedure (Method) for testing of earth pit resistance with necessary diagrams. 1) Earth Tester : i) Three point method ii) Four point method 2) By Potential drop method 3) Water ... of that earthing pit. In this test the accuracy is less but electrical rods are not required.  

Draw and explain the circuit diagram for measurement of single phase power using dynamometer type wattmeter.

Description : Draw and explain the circuit diagram for measurement of single phase power using dynamometer type wattmeter. 

Last Answer : Circuit diagram for measurement of single phase power using dynamometer type wattmeter: Explanation: It consists of two stationary coils, called current coils and one moving coil, called voltage or ... i.e. power. The meter can be calibrated directly to indicate the power in watts. 

Describe with neat circuit diagram the method of measurement of power in a High voltage, high current a.c circuit.

Description : Describe with neat circuit diagram the method of measurement of power in a High voltage, high current a.c circuit.

Last Answer : Circuit diagram:  Explanation:  The primary winding of P.T is connected across high voltage side and secondary winding is connected to pressure coil of low range wattmeter. The high voltage is ... is used Real power consumed = reading of wattmeter x ratio of C.T x ratio of P.T

The power measurement in a balanced 3-phase circuit can be done by:

Last Answer : The power measurement in a balanced 3-phase circuit can be done by: One wattmeter method, Two wattmeter method, Three wattmeter method.

The Navy classifies fiber optic connectors in what two ways?

Description : The Navy classifies fiber optic connectors in what two ways?

Last Answer : Light-duty and heavy-duty connectors.

What are the two ways to erase floppy disks?

Description : What are the two ways to erase floppy disks?

Last Answer : a. Degauss the disk and then reformat it. b. Reformat the disk.

What two ways can data be physically organized on a disk pack?

Description : What two ways can data be physically organized on a disk pack?

Last Answer : By cylinder or sector.

Electromagnetic radiation is hazardous to personnel in what two ways?

Description : Electromagnetic radiation is hazardous to personnel in what two ways?

Last Answer : Rf burns and biological, thermal, and neurological effects.

In what two ways are amplifiers classified?

Description : In what two ways are amplifiers classified?

Last Answer : By function and frequency response.

What software allows you to enter data and then retrieve it in a variety of ways?

Description : What software allows you to enter data and then retrieve it in a variety of ways?

Last Answer : Data management.

What are three ways of controlling radiated emi during transmission?

Description : What are three ways of controlling radiated emi during transmission?

Last Answer : a) physical separation of the antenna (b) limiting bandwidth of the antenna (c) use of directional antennas

What are three ways of controlling the amount of transmitter-generated emi?

Description : What are three ways of controlling the amount of transmitter-generated emi?

Last Answer : (a) filtering and shielding of the transmitter (b) limiting bandwidth (c) cutting the antenna to the

Microwave antennas and low-frequency antennas are similar in what ways?

Description : Microwave antennas and low-frequency antennas are similar in what ways?

Last Answer : Operating principles and electrical characteristics.

Technical manuals for tape recorders can state the SNR in what three different ways?

Description : Technical manuals for tape recorders can state the SNR in what three different ways?

Last Answer : a. Root-mean-square (RMS) signal-to-RMS noise. b. Peak-to-peak signal-to-RMS noise. c. Peak signal-to-RMS noise.

In what three ways are fuses rated?

Description : In what three ways are fuses rated?

Last Answer : Current, voltage, and time delay.

What are the three ways of combining cells, and what is each used for?

Description : What are the three ways of combining cells, and what is each used for?

Last Answer : Series, to increase voltage but not current. Parallel, to increase current but not voltage. Series-Parallel, to increase both current and

Describe three ways to prevent polarization.

Description : Describe three ways to prevent polarization.

Last Answer : Vent the cell, add a material rich in oxygen, and use a material that will absorb hydrogen.

Describe three ways to prevent polarization

Description : Describe three ways to prevent polarization

Last Answer : vent the cell, add a material rich in oxygen, and use a material that will absorb hydrogen.

What is the band of frequencies called that is included between the two points at which current falls to 70 percent of its maximum value in a resonant circuit?

Description : What is the band of frequencies called that is included between the two points at which current falls to 70 percent of its maximum value in a resonant circuit?

Last Answer : Bandwidth of the circuit

A two-cavity klystron without a feedback path will operate as what type of circuit?

Description : A two-cavity klystron without a feedback path will operate as what type of circuit?

Last Answer : Amplifier.

Name the two series circuits that exist in a diode circuit.

Description : Name the two series circuits that exist in a diode circuit.

Last Answer : Filament and plate.

A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Description : A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Last Answer : (a) 330 volts. (b) E1 = 150 volts. E2 = 180 volts. (c) 1.98 kilowatts. (d) P1 = 900 watts. P2 = 1.08 kilowatts component but in a parallel circuit total current divides among the available paths.

A circuit has a source voltage of 100 volts and two 50-ohm resistors connected in series. If the reference point for this circuit is placed between the two resistors, what would be the voltage at the reference point?

Description : A circuit has a source voltage of 100 volts and two 50-ohm resistors connected in series. If the reference point for this circuit is placed between the two resistors, what would be the voltage at the reference point?

Last Answer : 50 volts.

What are the two types of circuit protection devices?

Description : What are the two types of circuit protection devices?

Last Answer : Fuses and circuit breakers

Which type of splice is used to splice a lighting fixture to a branch circuit?

Description : Which type of splice is used to splice a lighting fixture to a branch circuit?

Last Answer : Fixture joint.