What is the band of frequencies called that is included between the two points at which current falls to 70 percent of its maximum value in a resonant circuit?

What is the band of frequencies called that is included  between the two points at which current falls to 70 percent of its  maximum value in a resonant circuit?
by

1 Answer

Answer :

Bandwidth of the circuit
by

Related questions

ECE Board Exam March 1996 An antenna which is not resonant at a particular frequencies and so can be used over a wide band of frequencies and so can be used over a wide band of frequencies is called A. aperiodic B. boresight C. cassegrain D. top-loaded

Description : ECE Board Exam March 1996 An antenna which is not resonant at a particular frequencies and so can be used over a wide band of frequencies and so can be used over a wide band of frequencies is called A. aperiodic B. boresight C. cassegrain D. top-loaded

Last Answer : A. aperiodic

What type filter is used to allow a narrow band of frequencies to pass through a circuit and attenuate all other frequencies above or below the desired band?

Description : What type filter is used to allow a narrow band of frequencies to pass through a circuit and attenuate all other frequencies above or below the desired band?

Last Answer : Bandpass.

In a parallel-resonant circuit, what is the relationship between impedance and current?

Description : In a parallel-resonant circuit, what is the relationship between impedance and current?

Last Answer : Maximum impedance, minimum current.

. In an "ideal" resonant circuit, what is the relationship between impedance and current?

Description : . In an "ideal" resonant circuit, what is the relationship between impedance and current?

Last Answer : Impedance low Current high.

What type filter is used to block the passage of current for a narrow band of frequencies, while allowing current to flow at all frequencies above or below this band?

Description : What type filter is used to block the passage of current for a narrow band of frequencies, while allowing current to flow at all frequencies above or below this band?

Last Answer : . Band-reject.

When a wide band of frequencies is transmitted simultaneously, each frequency will vary in the amount of fading. What is this variable fading called?

Description : When a wide band of frequencies is transmitted simultaneously, each frequency will vary in the amount of fading. What is this variable fading called?

Last Answer : Selective fading.

What equipment uses a calibrated resonant circuit to measure frequency?

Description : What equipment uses a calibrated resonant circuit to measure frequency?

Last Answer : Wavemeter.

What transmitter component allows the radiation of a large number of discrete frequencies over a wide band?

Description : What transmitter component allows the radiation of a large number of discrete frequencies over a wide band?

Last Answer : . Frequency synthesizer.

What device sweeps a band of frequencies to determine frequencies and amplitudes of each frequency component?

Description : What device sweeps a band of frequencies to determine frequencies and amplitudes of each frequency component?

Last Answer : Spectrum analyzer.

In series RLC circuit at resonant a) Voltage is in phase with current b) Current is maximum c) Inductive reactance = Capacitive reactance d) All of the above

Description : In series RLC circuit at resonant a) Voltage is in phase with current b) Current is maximum c) Inductive reactance = Capacitive reactance d) All of the above

Last Answer : Ans: All of the above

With a single modulating tone, what is the amplitude of the sideband frequencies at 100-percent modulation?

Description : With a single modulating tone, what is the amplitude of the sideband frequencies at 100-percent modulation?

Last Answer : One-half the amplitude of the carrier.

. A non-resonant line is a line that has no standing waves of current and voltage on it and is considered to be flat. Why is this true?

Description : . A non-resonant line is a line that has no standing waves of current and voltage on it and is considered to be flat. Why is this true?

Last Answer : The load impedance of such a line is equal to Z0.

For a series resonant circuit, at the half power points,which of the following is true?

Description : For a series resonant circuit, at the half power points,which of the following is true?  (a) Current is half of the current at resonance. (b) Resistance is equal to the reactance. (c) The impedance is half the impedance at the resonance. (d) None of the above

Last Answer : For a series resonant circuit, at the half power points,which of the following is true?  (a) Current is half of the current at resonance. (b) Resistance is equal to the reactance. (c) The impedance is half the impedance at the resonance. (d) None of the above

Receiver bandwidth is defined as those frequencies spread between what two points of the receiver response curve?

Description : Receiver bandwidth is defined as those frequencies spread between what two points of the receiver response curve?

Last Answer : Half-power points.

What term is used to describe the frequency at which the filter circuit changes from the point of rejecting the unwanted frequencies to the point of passing the desired frequencies?

Description : What term is used to describe the frequency at which the filter circuit changes from the point of rejecting the unwanted frequencies to the point of passing the desired frequencies?

Last Answer : Frequency cutoff (fco).

What circuit section is required in the output of a multivibrator modulator to eliminate unwanted output frequencies?

Description : What circuit section is required in the output of a multivibrator modulator to eliminate unwanted output frequencies?

Last Answer : An LCR filter.

A circuit is to be designed in which a capacitor must charge to 40 percent of the maximum charging voltage in 200 microseconds. The resistor to be used has a resistance of 40,000 ohms. What size capacitor must be used?

Description : A circuit is to be designed in which a capacitor must charge to 40 percent of the maximum charging voltage in 200 microseconds. The resistor to be used has a resistance of 40,000 ohms. What size capacitor must be used?

Last Answer : 0.1 microfarads 40% from the graph = 0.5

In a series resonant circuit, maximum voltage across L occurs at

Description : In a series resonant circuit, maximum voltage across L occurs at  (a) Resonant frequency (b) Slightly below resonant frequency (c) Slightly above resonant frequency (d) At a frequency where I is maximum

Last Answer : In a series resonant circuit, maximum voltage across L occurs at Slightly above resonant frequency

What is the device called that will separate alternating current from direct current, or that will separate alternating current of one frequency from other alternating currents of different frequencies?

Description : What is the device called that will separate alternating current from direct current, or that will separate alternating current of one frequency from other alternating currents of different frequencies?

Last Answer : A filter.

In series resonant circuit, increasing inductance to its twice value and reducing capacitance to its half value?

Description : In series resonant circuit, increasing inductance to its twice value and reducing capacitance to its half value?  

Last Answer : In series resonant circuit, increasing inductance to its twice value and reducing capacitance to its half value will increase the selectivity of the circuit.

What is the impedance of a crystal at its resonant frequency when it is used in the series mode?

Description : What is the impedance of a crystal at its resonant frequency when it is used in the series mode?

Last Answer : Minimum.

What is the impedance of a crystal at its resonant frequency when it is used in the parallel mode?

Description : What is the impedance of a crystal at its resonant frequency when it is used in the parallel mode?

Last Answer : Maximum

An a.c series circuit has resistance of 10ohm, inductance of 0.1H and capacitance of 10µf, voltage applied to circuit is 200V. find (i) Resonant frequency (ii) Current at resonance (iii) Power at resonance

Description : An a.c series circuit has resistance of 10ohm, inductance of 0.1H and capacitance of 10µf, voltage applied to circuit is 200V. find (i) Resonant frequency (ii) Current at resonance (iii) Power at resonance 

Last Answer : Solution: For RLC series circuit

In a series RLC circuit operating below the resonant frequency the current

Description : In a series RLC circuit operating below the resonant frequency the current  (a) I leads Vs (b) I lags Vs (c) I is in Phase with Vs (d) None of these

Last Answer : In a series RLC circuit operating below the resonant frequency the current  I leads Vs 

In a series RLC circuit that is operating above the resonant frequency, the current : -

Description : In a series RLC circuit that is operating above the resonant frequency, the current : -  a) lags the applied voltage b) leads the applied voltage c) is in phase with the applied voltage d) is zero

Last Answer : In a series RLC circuit that is operating above the resonant frequency, the current : - lags the applied voltage

How does transit time affect the relationship of the grid voltage and the plate current at high frequencies?

Description : How does transit time affect the relationship of the grid voltage and the plate current at high frequencies?

Last Answer : Transit time causes the grid voltage and plate current to be out of phase

When a capacitor is connected in series with a Marconi antenna? A. Antenna open circuit stops transmission B. An inductor of equal value must be added C. No change occurs to antenna D. Antenna resonant frequency increases

Description : When a capacitor is connected in series with a Marconi antenna? A. Antenna open circuit stops transmission B. An inductor of equal value must be added C. No change occurs to antenna D. Antenna resonant frequency increases

Last Answer : D. Antenna resonant frequency increases

In R-L-C series resonant circuit magnitude of resonance frequency can be changed by changing the value of?

Description : In R-L-C series resonant circuit magnitude of resonance frequency can be changed by changing the value of?

Last Answer : In R-L-C series resonant circuit magnitude of resonance frequency can be changed by changing the value of L or C.

How is the Resonant Peak (Mr), resonant frequency (ωr), and band width determined from Nichols chart?

Description : How is the Resonant Peak (Mr), resonant frequency (ωr), and band width determined from Nichols chart?

Last Answer : i) The resonant peak is given by the value of ω contour which is tangent to G(j ω ii) The resonant frequency is given by the frequency of G(jω iii) The bandwidth is given by frequency corresponding to the intersection point of G(jω – 3dB M-contour.

What two variables determine the primary frequency of a resonant cavity?

Description : What two variables determine the primary frequency of a resonant cavity?

Last Answer : Size and shape of the cavity.

The resonant frequency of electron wobble can be changed by variation of what force?

Description : The resonant frequency of electron wobble can be changed by variation of what force?

Last Answer : The applied magnetic field.

Inductive tuning of a resonant cavity is accomplished by placing a nonmagnetic slug in what area?

Description : Inductive tuning of a resonant cavity is accomplished by placing a nonmagnetic slug in what area?

Last Answer : The area of maximum H lines.

How will an iris that has portions along both the "a" and "b" dimension walls act at the resonant frequency?

Description : How will an iris that has portions along both the "a" and "b" dimension walls act at the resonant frequency?

Last Answer : As a shunt resistance.

If the inductor and capacitor values are increased, what happens to the resonant frequency?

Description : If the inductor and capacitor values are increased, what happens to the resonant frequency?

Last Answer : Decreases.

Without strapping, the resonant cavities of a hole-and-slot anode are connected in what manner?

Description : Without strapping, the resonant cavities of a hole-and-slot anode are connected in what manner?

Last Answer : Series.

A cylindrical copper block with resonant cavities around the circumference is used as what component of a magnetron?

Description : A cylindrical copper block with resonant cavities around the circumference is used as what component of a magnetron?

Last Answer : Anode or plate

Where do the maximum current and minimum voltage values on a resonant Hertz dipole exist? A. Center of the antenna B. Near the end of the antenna C. Near the center of the antenna D. Ends of the antenna

Description : Where do the maximum current and minimum voltage values on a resonant Hertz dipole exist? A. Center of the antenna B. Near the end of the antenna C. Near the center of the antenna D. Ends of the antenna

Last Answer : A. Center of the antenna

A resonant system has a fundamental frequency of 100 Hz. If the next higher frequency that gives a resonance are 300 Hz and 500 Hz, the system could be (a) A pip open at both ends (b) A pipe closed at both ends (c) A string vibrating between two fixed points (d) A pipe open at one end and closed at the other

Description : A resonant system has a fundamental frequency of 100 Hz. If the next higher frequency that gives a resonance are 300 Hz and 500 Hz, the system could be (a) A pip open at both ends (b) A pipe ... (c) A string vibrating between two fixed points (d) A pipe open at one end and closed at the other

Last Answer : Ans:(d)

Gross assets are Rs.1,01,000, fictitious assets Rs.350 are included in the gross assets. External liabilities are Rs.7,500. 6% prefer share capital is Rs.45,000. Equity capital is 4,500 equity shares of Rs.10 each fully paid. Average expected profit is Rs.8,500. Transfer to reserves is 10%. Pref. dividend is payable. NRR is 9%. The Net Asset Value Per share is A Rs.11 B Rs.10.70 C Rs.15 D Rs.20s

Description : Gross assets are Rs.1,01,000, fictitious assets Rs.350 are included in the gross assets. External liabilities are Rs.7,500. 6% prefer share capital is Rs.45,000. Equity capital is 4,500 equity shares of Rs.10 each fully ... . The Net Asset Value Per share is A Rs.11 B Rs.10.70 C Rs.15 D Rs.20

Last Answer : Rs.10.70

A tuned circuit has a Q of 100 at its resonant frequency of 500 kHz. Its bandwidth is _____kHz.

Description : A tuned circuit has a Q of 100 at its resonant frequency of 500 kHz. Its bandwidth is _____kHz. (A) 50000 (B) 0.2 (C) 600 (D) 5

Last Answer : A tuned circuit has a Q of 100 at its resonant frequency of 500 kHz. Its bandwidth is 5 kHz.

What is the filter called that passes low frequencies but rejects or attenuates high frequencies?

Description : What is the filter called that passes low frequencies but rejects or attenuates high frequencies?

Last Answer : Low-pass filter, high-frequency discriminator or high-frequency attenuator.

What is the filter called in which the low frequencies do not produce a useful voltage?

Description : What is the filter called in which the low frequencies do not produce a useful voltage?

Last Answer : High-pass filter, low-frequency discriminator, or low-frequency attenuator.

Which band of frequencies used by military for its satellites and radar? A. C band B. X band C. L band D. P band

Description : Which band of frequencies used by military for its satellites and radar? A. C band B. X band C. L band D. P band

Last Answer : B. X band

A cavity that vibrates at its natural frequency produces a louder sound than at other frequencies. What term is used to describe this phenomenon?

Description : A cavity that vibrates at its natural frequency produces a louder sound than at other frequencies. What term is used to describe this phenomenon?

Last Answer : Resonance.

The maximum amount of electrolytes and water (70 – 80 percent) from the glomerular filtrate is reabsorbed in which part of the nephron? (a) Ascending limb of loop of Henle (b) Distal convoluted tubule (c) Proximal convoluted tubule (d) Descending limb of loop of Henle

Description : The maximum amount of electrolytes and water (70 – 80 percent) from the glomerular filtrate is reabsorbed in which part of the nephron? (a) Ascending limb of loop of Henle (b) Distal convoluted tubule (c) Proximal convoluted tubule (d) Descending limb of loop of Henle

Last Answer : (c) Proximal convoluted tubule

What is a Resonant Circuit ?

Description : What is a Resonant Circuit ?

Last Answer : When the inductive reactance and capacitance are equal in an AC series circuit , then that circuit is called resonant circuit.

Determine the lower half-power frequency of a class-C amplifier having upper half-power frequency of 10.025 MHz, a resonant frequency 5 MHz and a circuit Q of 10. A. 1.0025 MHz B. 10.525 MHz C. 0.5 MHz D. 10 MHz

Description : Determine the lower half-power frequency of a class-C amplifier having upper half-power frequency of 10.025 MHz, a resonant frequency 5 MHz and a circuit Q of 10. A. 1.0025 MHz B. 10.525 MHz C. 0.5 MHz D. 10 MHz

Last Answer : A. 1.0025 MHz

Derive an expression for resonant frequency of series RLC circuit.

Description : Derive an expression for resonant frequency of series RLC circuit.

Last Answer : At resonance frequency in RLC series circuit, we have inductive reactance is equal to capacitive reactance i.e.  Where fr is the resonant frequency in RLC series circuit. 

A series R-L-C Circuit has a resonant frequency of 1000 Hz. If the values of R, L and C are

Description : A series R-L-C Circuit has a resonant frequency of 1000 Hz. If the values of R, L and C are doubled, the new resonant frequency is

Last Answer : A series R-L-C Circuit has a resonant frequency of 1000 Hz. If the values of R, L and C are doubled, the new resonant frequency is 500 Hz