Description : An instrument thAn instrumAn instrument that must be calibrated in place requires what type of calibration label?
Last Answer : SPECIAL CALIBRATION label.
Description : What is not included in prevention costs? a) quality planning b) formal technical reviews c) test equipment d) equipment calibration and maintenance
Last Answer : Ans: d
Description : If a gauge is installed perpendicular to the slope, its measurement is reduced by multiplying (A) Sine of the angle of inclination with vertical (B) Cosine of the angle of inclination with vertical (C) Tangent of the angle of inclination with vertical (D) Calibration coefficient of the gauge
Last Answer : Answer: Option B
Description : The calibration of an HPLC detector can be evaluated by measurement of? A. Retention time B. Temperature C. Flow rate accuracy D. Intensity of the peak
Last Answer : D. Intensity of the peak
Description : Explain calibration of capacitive type level measurement.
Last Answer : ➢ Calibration of capacitance type level transmitter 1. Remove the level transmitter from the system(tank). 2. check whether transmitter shows zero reading by connecting with multimeter otherwise release the ... rotate the span screw to 20ma. 3. Repeat these steps and check all readings
Description : What information must be known to determine the component values for a voltage divider?
Last Answer : The source voltage and load requirements (voltage and current).
Description : Which of the following would not be required to be checked before welding? a) The welding consumables b) The welder qualification c) Calibration of the welding equipment d) The workshop humidity
Last Answer : d) The workshop humidity
Description : What is pressure calibration? State stepwise procedure to test the accuracy of pressure gauge with dead weight tester.
Last Answer : Explanation- The handle is fully drawn out and the oil is allowed to enter in the cylinder (i.e. gauge and piston). A known accurate weight is placed on the platform. The area of ... reduce the friction between the piston and cylinder, the piston is gradually rotated while a reading being taken
Description : What test equipment is designed to generate, modify, or measure a range of parameters of electronic functions of a specific nature required to test a single system or equipment?
Last Answer : Special-purpose electronic test equipment.
Description : Name the two classes of test equipment.
Last Answer : General-purpose electronic test equipment (GPETE) and special-purpose electronic test equipment (SPETE).
Description : What system is currently used by all branches of the military to identify test equipment?
Last Answer : Joint Electronics Type Designation System (JETDS).
Description : NELAT and VAST are examples of what type of test equipment?
Last Answer : Off-line.
Description : What test equipment continuously monitors electronic systems?
Last Answer : On-line.
Description : List the three groups of test equipment used for fault isolation in 2M repair.
Last Answer : On-line, off-line, and General Purpose Electronic Test Equipment (GPETE)
Description : You plan to measure your tape recorder’s SNR. What test equipment will you need?
Last Answer : A VTVM and a signal generator.
Description : Why should you avoid using ac-powered test equipment when wearing a wrist strap?
Last Answer : For your own safety.
Description : The frequency response of test equipment refers to what aspect of ac voltage measurements?
Last Answer : the range of frequencies that can accurately be measured.
Description : The input impedance of your test equipment should exceed the impedance of the circuit under test by what ratio?
Last Answer : 10 to 1
Description : What assures the accuracy of your electronic test equipment?
Last Answer : Its calibration.
Description : Big label helps to calculate actual money to be spent on a) Maintenance bills c) Electricity bills b) Repairing d) None of above
Last Answer : Electricity bills
Description : The contractor provides the financing and is paid an agreed fraction of actual savings achieved. This payment is used to pay down the debt costs of equipment and/or services. ... contract b) extended technical guarantee/service c) performance Contract d) shared savings performance contrac
Last Answer : d) shared savings performance contrac
Description : What is the formula for determining total reactance in a series circuit where the values of XC and XL are known?
Last Answer : X = XL – XC or X = XC - XL
Description : Correcting the seed rate is known as a) Standardization b) Filtration c) Calibration d) Testing Ans. c
Last Answer : ans c
Description : How closely a measurement reflects the actual value is what?
Last Answer : llol
Description : First step in the controlling process is: a. Taking corrective action b. Analyzing the deviation c. Determining Standards d. Measurement of actual progress
Last Answer : c. Determining Standards
Description : What must be used to test an activated circuit?
Last Answer : Approved meters or other indicating devices
Description : When measuring receiver sensitivity, what quantities must you add to the dBm reading obtained on the signal generator or test set?
Last Answer : Attenuations of the directional coupler and the connecting cable.
Description : Why should you use the highest range of an ammeter for the initial measurement?
Last Answer : To prevent damage to the meter movement from excessive current.
Description : What is the range of the characteristic impedance of lines used in actual practice?
Last Answer : Between 50 and 600 ohms.
Description : When taking a voltage measurement, which lead of the voltmeter should you connect to the circuit first?
Last Answer : Ground.
Description : On what range should you set the voltmeter prior to taking a voltage measurement?
Last Answer : Highest.
Description : What unit of measurement refers to the torque of a synchro transmitter
Last Answer : Ounce-inches.
Description : What radar scope uses a range step for range measurement?
Last Answer : The A scope.
Description : What is the primary measurement application for tuning forks?
Last Answer : They are used to monitor fixed motor speeds.
Description : A transmission line is said to have distributed constants of inductance, capacitance, and resistance along the line. What units of measurement are used to express these constants?
Last Answer : Inductance is expressed in micro henrys per unit length, capacitance is expressed in picofarads per unit length, and resistance is expressed in ohms per unit length.
Last Answer : Standing-wave ratio (swr).
Description : What is the unit of measurement of apparent power?
Last Answer : Apparent power
Description : What is the unit of measurement of reactive power?
Last Answer : var.
Description : What is the unit of measurement of true power?
Description : When is an optical power meter measurement recommended for conducting field measurements on installed optical fiber cables or cable plants?
Last Answer : When an installed optical fiber cable or cable plant is less than 50 meters in length.
Description : When using an American Standard Wire Gauge to determine the size of a wire, where should you place the wire in the gauge to get the correct measurement?
Last Answer : In the parallel walled slot not the circular area.
Description : What other measurement can an ohmmeter make?
Last Answer : Circuit continuity.
Description : What range of an ammeter is selected for the final measurement?
Last Answer : A range that allows a meter reading near the center of the scale.
Description : What are two ways that circuit measurement is used?
Last Answer : Circuit measurement is used to (1) monitor the operation of a piece of electrical or electronic equipment and (2) determine the reason a piece of electrical or electronic equipment is not functioning properly.
Description : If rubber goods are tested and inspected in house, the individual or individuals performing the tests must NOT test and certify their own personal protective equipment.?
Last Answer : True.
Description : Can the default values be assigned to actual parameters?
Last Answer : Yes
Description : Pick out the wrong statement. (A) Theoretical flame temperature is the temperature attained by the products of combustion, when the fuel is burned without loss or gain of heat (B) ... flame temperature (D) Adiabatic flame temperatures of actual combustions are always less than the maximum values
Last Answer : (C) Burning the fuel with excess pure oxygen results in maximum theoretical flame temperature
Description : In a relational database model, NULL values can be used for all but which one of the following? (A) To allow duplicate tuples in the table by filling the primary key column(s) with NULL. (B) To ... D) To fill a column in a tuple when that column does not really exist for that particular tuple.
Last Answer : (A) To allow duplicate tuples in the table by filling the primary key column(s) with NULL.
Description : An oscilloscope provides easy measurement of __ values.
Last Answer : peak to peak