Description : A tube has a transconductance of 800 mhos and a load resistor of 50 kohms. When control grid voltage varies by 6 volts, the plate voltage will vary by what amount?
Last Answer : 240 volts.
Description : If the load in question 50 requires a voltage of +90 V, what should be the value of the bleeder resistor?
Last Answer : 2 kΩ
Description : Source transformation Replace the circuit with voltage source in series with a single resistor
Last Answer : Source transformation Replace the circuit with voltage source in series with a single resistor
Description : What term identifies a single resistor that represents total resistance of a complex circuit?
Last Answer : Equivalent resistor or Req.
Description : A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?
Last Answer : (a) 330 volts. (b) E1 = 150 volts. E2 = 180 volts. (c) 1.98 kilowatts. (d) P1 = 900 watts. P2 = 1.08 kilowatts component but in a parallel circuit total current divides among the available paths.
Description : If the current was increased to 4 amps, what would be the voltage drop across each resistor in the circuit described in question 17?
Last Answer : E1 = 80 volts. E2 = 240 volts. E3 = 320 volts
Description : What is the voltage dropped by each resistor of the circuit described in question 17?
Last Answer : E1 = 60 volts. E2 = 180 volts. E3 = 240 volts.
Description : What is the power used in a circuit that has 10 amperes of current through a 10-ohm resistor?
Last Answer : 1 kilowatt.
Description : What type of resistor should be used in the circuit described in question 12?
Last Answer : A wirewound resistor.
Description : A circuit is to be designed in which a capacitor must charge to 40 percent of the maximum charging voltage in 200 microseconds. The resistor to be used has a resistance of 40,000 ohms. What size capacitor must be used?
Last Answer : 0.1 microfarads 40% from the graph = 0.5
Description : What is the RC time constant of a series RC circuit that contains a 12-megohm resistor and a 12-microfarad capacitor?
Last Answer : 144 seconds (t=R x C)
Description : What is the voltage drop across the resistor in an RC charging circuit when the charge on the capacitor is equal to the battery voltage?
Last Answer : Zero.
Description : At what instant does the greatest voltage appear across the resistor in a series RC circuit when the capacitor is charging?
Last Answer : At the instant of the initiation of the action.
Description : The total power consumed in a parallel circuit is __________. A. the sum of the powers used in each load (resistor) divided by the number of loads B. always less than the power used in the smallest ... of the powers used in each individual load D. never more than the power used in the largest load
Last Answer : Answer: C
Description : The total power used up in a series circuit is ___________. A. the sum of the powers used in each load (resistor) divided by the number of loads B. the sum of the powers used in each load C. always less than the power used in the smallest load D. never more than the power used in largest load
Last Answer : Answer: B
Description : What is the direction of current through the load resistor in the circuit shown in the illustration? EL-0085 A. Always from point 'Z' to the grounded end. B. Always from the grounded end to ... on the instantaneous polarity at point 'W'. D. It cannot be determined without a directional ammeter.
Description : How do i replace blower resistor in 2011 Lincoln MKS?
Last Answer : Feel Free to Answer
Description : A resistor is handed to you for identification with the following color code: the first band is blue, followed by gray, green, gold, and brown. What is the resistor’s value?
Last Answer : 6,800,000 ohms (6.8 mega ohms), with 5% tolerance, and a 1% reliability level.
Description : The same resistor mentioned in question 63 has a yellow fifth band. What does this signify?
Last Answer : The resistor’s chance of failure is 0.001 percent for 1000 hours of operation.
Description : A carbon resistor has the following color bands: The first band is yellow, followed by violet, yellow, and silver. What is the ohmic value of the resistor?
Last Answer : 470,000 ohms (470 kilo ohms).
Description : A carbon resistor has a resistance of 50 ohms, and a tolerance of 5 percent. What are the colors of bands one, two, three, and four, respectively?
Last Answer : The bands are green, black, black, and gold.
Description : . Which type of variable resistor should you select for controlling a large amount of current?
Last Answer : The rheostat.
Description : What type resistor should be used to overcome the disadvantages of the carbon resistor?
Last Answer : The wirewound resistor.
Description : What does the wattage rating of a resistor indicate?
Last Answer : Its ability to dissipate heat
Description : Four equal resistors are connected in parallel, each resistor has an ohmic value of 100 ohms, what is the equivalent resistance?
Last Answer : 25 ohms
Description : What is the time constant of the resistor and capacitor in a peak detector for pam?
Last Answer : At least 10 times the interpulse period.
Description : What factors determine the value of the multiplier resistor?
Last Answer : The current required for full-scale deflection, and the range of the voltage to be measured.
Description : In an experiment on studying the dependence of current flowing through a given resistor on the potential difference applied across it, list two ways how a student would change the values of current in the circuit?
Last Answer : Answer. There are two ways in which a student can change the values of current in the circuit: By increasing or decreasing the number of cells. By changing the value of resistance.
Description : As the tube filaments in the load heat up, will the circuit current increase or decrease?
Last Answer : Decrease.
Description : what part of the circuit is the (a) load and (b) source?
Last Answer : a) DS1, the flashlight bulb (b) BAT, the dry cell
Description : A good choice of shunt resistance will place the indicating pointer near what part of the meter scale with a normal load?
Last Answer : Midscale.
Description : The most inefficient method of voltage reduction, from the standpoint of power loss, even when placed in series with the load, is the use of a/an ____________. A. capacitor B. inductor C. resistor D. transistor
Description : The most inefficient method of voltage reduction from the stand point of power loss, is a/an _____________. A. capacitor in series with the load B. inductor in series with the load C. capacitor and inductor in series with the load D. resistor in series with the load
Last Answer : Answer: D
Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source
Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals
Description : The front-end of a television receiver, having a bandwidth of 7Mhz, and operating at a temperature of 27˚C , consists of an amplifier having a gain of 15 followed by a mixer whose gain is 20. The ... equivalent noise resistance for this television receiver. A. 8760 Ω B. 875Ω C. 8.76Ω D. 0.876Ω
Last Answer : B. 875Ω
Description : When you replace components, identification marks must meet what requirements?
Last Answer : They should be readable from a single point.
Description : In the circuit shown the voltage drop across the `15Omega` resistor is `30 V` having the polarity as indicated. The ratio of potential difference acro
Last Answer : In the circuit shown the voltage drop across the `15Omega` resistor is `30 V` having the ... difference across `5Omega` and resistance `R` is
Description : In the circuit shown in Fig. 4.63, the terminal voltage of the battery is 6.0 V. Find the current I through the `18 Omega` resistor.
Last Answer : In the circuit shown in Fig. 4.63, the terminal voltage of the battery is 6.0 V. Find the current I through the `18 Omega` resistor.
Description : Find the equivealent resistance of the circuit shown in Fig. 4.61 between the points P and Q. Each resistor has a resistance r.
Last Answer : Find the equivealent resistance of the circuit shown in Fig. 4.61 between the points P and Q. Each resistor has a resistance r.
Description : Find the equivalent resistance of the circuit shown in Fig.4.60 between the points A and B. Each resistor has a resistance r.
Last Answer : Find the equivalent resistance of the circuit shown in Fig.4.60 between the points A and B. Each resistor has a resistance r.
Description : In the circuit shown here, what is the value of the unknown resistor R so that the total resistance of the circuit between points P and Q is also equa
Last Answer : In the circuit shown here, what is the value of the unknown resistor R so that the total resistance of the ... ` C. `sqrt(69)Omega` D. `10 Omega`
Description : A series wound DC motor has its armature and field connected in series with a resistor. When the motor is disconnected from its power supply, this motor will exemplify __________. A. the ... the proper connections for an automatic strip heater C. a reversing controller circuit D. dynamic braking
Description : In the illustration, the signal from the device connected to terminals 18 and 19 is __________. EL-0046 A. prime mover speed feedback B. loss of control alarm when comparing with the input signal ... slip between the prime mover and the alternator D. to shut down the prime mover if overspeeding
Last Answer : Answer: A
Description : The winch shown in the illustration will not operate in any speed in the lowering direction and at an abnormal speed in 'first point hoist'. The possible cause is that _______________. EL-0102 A. ... '1M' in the power circuit are badly corroded D. master switch contacts 'MS6' have weak springs
Description : In the illustrated motor controller circuit, which statment is true? EL-0023 A. The high and low speed lights operate at less than line voltage with a resistor in series. B. This controller can be ... . The wattage of the high speed light must be greater than the wattage of the low speed light.
Description : When a resistor is used as a shunt and is connected in parallel with a meter movement coil, it will provide _____________. A. a measurement of circuit resistance B. an increased accuracy of approximately 1.5 percent C. an extended meter range D. none of the above
Description : In the illustrated circuit 'A', what power is consumed by a 3 ohm resistor with a 12 volt source? EL-0041 A. 12 watts B. 48 watts C. 64 watts D. 232 watts
Description : In the illustration what is the minimum wattage needed for a 3 ohm resistor with a 12 VDC power source in circuit 'A'? EL-0041 A. 12 watts B. 48 watts C. 64 watts D. 232 watts
Description : The purpose of resistor bank 'R1-R5' in the winch circuit shown in the illustration is to ______________. EL-0102 A. limit armature current in lower and 'series field' current in hoist to ... required speeds D. regulate the strength of the brake solenoid 'B1-B2' in both directions of operation
Description : When troubleshooting a console circuit card suspected of being faulty, first check operating voltages, clean the card and then _________________. A. make sure wired connections and push-on connectors ... circuit traces with an ohmmeter D. measure the gain of each transistor or integrated circuit