What factors determine the value of the multiplier resistor?

What factors determine the value of the multiplier resistor?
by

1 Answer

Answer :

The current required for full-scale deflection, and the range of  the voltage to be measured.
by

Related questions

What is the purpose of frequency-multiplier stages in a VHF transmitter?

Description : What is the purpose of frequency-multiplier stages in a VHF transmitter?

Last Answer : To raise the low frequency of a stable oscillator to the vhf range.

A resistor is handed to you for identification with the following color code: the first band is blue, followed by gray, green, gold, and brown. What is the resistor’s value?

Description : A resistor is handed to you for identification with the following color code: the first band is blue, followed by gray, green, gold, and brown. What is the resistor’s value?

Last Answer : 6,800,000 ohms (6.8 mega ohms), with 5% tolerance, and a 1% reliability level.

A carbon resistor has the following color bands: The first band is yellow, followed by violet, yellow, and silver. What is the ohmic value of the resistor?

Description : A carbon resistor has the following color bands: The first band is yellow, followed by violet, yellow, and silver. What is the ohmic value of the resistor?

Last Answer : 470,000 ohms (470 kilo ohms).

If the load in question 50 requires a voltage of +90 V, what should be the value of the bleeder resistor?

Description : If the load in question 50 requires a voltage of +90 V, what should be the value of the bleeder resistor?

Last Answer : 2 kΩ

Four equal resistors are connected in parallel, each resistor has an ohmic value of 100 ohms, what is the equivalent resistance?

Description : Four equal resistors are connected in parallel, each resistor has an ohmic value of 100 ohms, what is the equivalent resistance?

Last Answer : 25 ohms

. What three factors determine the amplitude of the voltage induced into a stator winding?

Description : . What three factors determine the amplitude of the voltage induced into a stator winding?

Last Answer : The amplitude of the primary voltage, the turns ratio, and the angular displacement between the rotor and the stator winding.

What three main factors determine the amount of refraction in the ionosphere?

Description : What three main factors determine the amount of refraction in the ionosphere?

Last Answer : (a) density of ionization of the layer (b) frequency (c) angle at which it enters the layer

. What are two of the three physical factors that determine the values of capacitance and inductance of a transmission line?

Description : . What are two of the three physical factors that determine the values of capacitance and inductance of a transmission line?

Last Answer : (1) Type of line used, (2) dielectric in the line, and (3) length of line.

The way a magnetic head will be used determines how it is constructed. Name three factors that determine the final construction of a magnetic head.

Description : The way a magnetic head will be used determines how it is constructed. Name three factors that determine the final construction of a magnetic head.

Last Answer : a. Type of head (record, reproduce, or erase). b. Frequencies it will record or reproduce. c. Whether it will be used on a single or multitrack recorder.

What factors determine the rigidity of a gyro?

Description : What factors determine the rigidity of a gyro?

Last Answer : Rotor speed, weight, shape.

What factors determine the direction of rotation in a dc motor?

Description : What factors determine the direction of rotation in a dc motor?

Last Answer : Direction of armature current, and direction of magnetic flux in field.

hat two factors determine the directivity pattern of the parasitic array?

Description : hat two factors determine the directivity pattern of the parasitic array?

Last Answer : Length of the parasitic element (tuning) and spacing between the parasitic and driven elements.

What three factors determine the type, size, and shape of an antenna?

Description : What three factors determine the type, size, and shape of an antenna?

Last Answer : Frequency of operation of the transmitter, amount of power to be radiated, and general direction of the receiving set.

What two factors determine the frequency of the output voltage of an alternator?

Description : What two factors determine the frequency of the output voltage of an alternator?

Last Answer : Speed of rotation and number of poles.

The value of investment multiplier relates to - (1) change in income due to change in autonomous investment. (2) change in autonomous investment due to change in income. (3) change in income due to change in consumption. (4) change in the income due to change in induced investment.

Description : The value of investment multiplier relates to - (1) change in income due to change in autonomous investment. (2) change in autonomous investment due to change in income. (3) change in income due to change in consumption. (4) change in the income due to change in induced investment.

Last Answer : (2) change in autonomous investment due to change in income. Explanation: The term investment multiplier refers to the concept that any increase in public or private investment spending has a ... . The investment multiplier tries to determine the financial impact for a public or private project.

Ceteris paribus, an income tax (a) Increases the value of the expenditure multiplier and decreases the value of the net tax revenue multiplier; (b) Decreases the value of the expenditure and net tax revenue multiplier; (c) Decreases the value of the expenditure multiplier and increases the value of the net tax revenue multiplier ; (d) None of the above.

Description : Ceteris paribus, an income tax (a) Increases the value of the expenditure multiplier and decreases the value of the net tax revenue multiplier; (b) Decreases the value of the expenditure and net tax ... multiplier and increases the value of the net tax revenue multiplier ; (d) None of the above.

Last Answer :  (b) Decreases the value of the expenditure and net tax revenue multiplier;

The value of investment multiplier relates to (1) change in income due to change in autonomous investment. (2) change in autonomous investment due to change in income. (3) change in income due to change in consumption. (4) change in the income due to change in induced investment.

Description : The value of investment multiplier relates to (1) change in income due to change in autonomous investment. (2) change in autonomous investment due to change in income. (3) change in income due to change in consumption. (4) change in the income due to change in induced investment.

Last Answer : change in autonomous investment due to change in income.

What name is given to a resistor used to replace the normal load in a circuit?

Description : What name is given to a resistor used to replace the normal load in a circuit?

Last Answer : Dummy load or dummy antenna.

The same resistor mentioned in question 63 has a yellow fifth band. What does this signify?

Description : The same resistor mentioned in question 63 has a yellow fifth band. What does this signify?

Last Answer : The resistor’s chance of failure is 0.001 percent for 1000 hours of operation.

A carbon resistor has a resistance of 50 ohms, and a tolerance of 5 percent. What are the colors of bands one, two, three, and four, respectively?

Description : A carbon resistor has a resistance of 50 ohms, and a tolerance of 5 percent. What are the colors of bands one, two, three, and four, respectively?

Last Answer : The bands are green, black, black, and gold.

. Which type of variable resistor should you select for controlling a large amount of current?

Description : . Which type of variable resistor should you select for controlling a large amount of current?

Last Answer : The rheostat.

What type resistor should be used to overcome the disadvantages of the carbon resistor?

Description : What type resistor should be used to overcome the disadvantages of the carbon resistor?

Last Answer : The wirewound resistor.

What does the wattage rating of a resistor indicate?

Description : What does the wattage rating of a resistor indicate?

Last Answer : Its ability to dissipate heat

A tube has a transconductance of 800 mhos and a load resistor of 50 kohms. When control grid voltage varies by 6 volts, the plate voltage will vary by what amount?

Description : A tube has a transconductance of 800 mhos and a load resistor of 50 kohms. When control grid voltage varies by 6 volts, the plate voltage will vary by what amount?

Last Answer : 240 volts.

What term identifies a single resistor that represents total resistance of a complex circuit?

Description : What term identifies a single resistor that represents total resistance of a complex circuit?

Last Answer : Equivalent resistor or Req.

A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Description : A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Last Answer : (a) 330 volts. (b) E1 = 150 volts. E2 = 180 volts. (c) 1.98 kilowatts. (d) P1 = 900 watts. P2 = 1.08 kilowatts component but in a parallel circuit total current divides among the available paths.

If the current was increased to 4 amps, what would be the voltage drop across each resistor in the circuit described in question 17?

Description : If the current was increased to 4 amps, what would be the voltage drop across each resistor in the circuit described in question 17?

Last Answer : E1 = 80 volts. E2 = 240 volts. E3 = 320 volts

What is the voltage dropped by each resistor of the circuit described in question 17?

Description : What is the voltage dropped by each resistor of the circuit described in question 17?

Last Answer : E1 = 60 volts. E2 = 180 volts. E3 = 240 volts.

What is the power used in a circuit that has 10 amperes of current through a 10-ohm resistor?

Description : What is the power used in a circuit that has 10 amperes of current through a 10-ohm resistor?

Last Answer : 1 kilowatt.

What type of resistor should be used in the circuit described in question 12?

Description : What type of resistor should be used in the circuit described in question 12?

Last Answer : A wirewound resistor.

What is the time constant of the resistor and capacitor in a peak detector for pam?

Description : What is the time constant of the resistor and capacitor in a peak detector for pam?

Last Answer : At least 10 times the interpulse period.

A circuit is to be designed in which a capacitor must charge to 40 percent of the maximum charging voltage in 200 microseconds. The resistor to be used has a resistance of 40,000 ohms. What size capacitor must be used?

Description : A circuit is to be designed in which a capacitor must charge to 40 percent of the maximum charging voltage in 200 microseconds. The resistor to be used has a resistance of 40,000 ohms. What size capacitor must be used?

Last Answer : 0.1 microfarads 40% from the graph = 0.5

What is the RC time constant of a series RC circuit that contains a 12-megohm resistor and a 12-microfarad capacitor?

Description : What is the RC time constant of a series RC circuit that contains a 12-megohm resistor and a 12-microfarad capacitor?

Last Answer : 144 seconds (t=R x C)

What is the voltage drop across the resistor in an RC charging circuit when the charge on the capacitor is equal to the battery voltage?

Description : What is the voltage drop across the resistor in an RC charging circuit when the charge on the capacitor is equal to the battery voltage?

Last Answer : Zero.

At what instant does the greatest voltage appear across the resistor in a series RC circuit when the capacitor is charging?

Description : At what instant does the greatest voltage appear across the resistor in a series RC circuit when the capacitor is charging?

Last Answer : At the instant of the initiation of the action.

An ammeter with an internal resistance of 50 ohm(s) is used to measure a current thorugh a lod resistor Rl = 1 kohm(s). Determine the percentage error of the reading due to ammeter insertion.

Description : An ammeter with an internal resistance of 50 ohm(s) is used to measure a current thorugh a lod resistor Rl = 1 kohm(s). Determine the percentage error of the reading due to ammeter insertion.

Last Answer : 50/(50+1k)*100 = 4.76%

A supply of 24 V DC is applied across a circuit which consist of three resistors connected in parallel R1= 1.2KΩ, R2= 560 Ω, R3= 2.1Ω and a fourth resistor of 7.8 Ω connected in series with the parallel group. Determine the current, voltage and power across each resistor

Last Answer : Req= (1/1200 +1/560 + 1/2.1)^-1        = 2.1 ohms RT= 2.1 + 7.8      = 9.9 ohms IT = V/R = 24/9.9                = 2.4 A Veq= R I =  2.1 2 ... 7.8         = 12.096 w                 = 44.928 w _________________________________________ By: Ellis-Junior Kamatjipose [email protected]

To determine the polarity of the voltage drop across a resistor, it is necessary to know?

Description : To determine the polarity of the voltage drop across a resistor, it is necessary to know?

Last Answer : To determine the polarity of the voltage drop across a resistor, it is necessary to know direction of current through the resistor.

Which multiplier gives a faster rate of increase, exponential or logarithmic?

Description : Which multiplier gives a faster rate of increase, exponential or logarithmic?

Last Answer : Exponential. Try exponentially putting money on a checker board, start with square one with one a penny…

planting multiplier onions in the fall

Description : planting multiplier onions in the fall

Last Answer : Need Answer

what are multiplier onions and why are the called that

Description : what are multiplier onions and why are the called that

Last Answer : Need Answer

What is Voltage Multiplier ?

Description : What is Voltage Multiplier ?

Last Answer : The rectifier circuit input AC . The output multiplier is called the voltage multiplier by receiving several times the increased DC voltage at the output.

Multiplier Who Say ?

Last Answer : a Numbers By That All Numbers Finally Divisible , he All To the number The first Of the number Multiplier Says . Example 2 By 4 , 6 , 17

do you know the big multiplier?

Description : can you still count on paper, do you need a calculator? if you do not know or the flashlight on the calculator (phone) has run out, do not despair. The Japanese made a nice draw: Well, how do you like it? (tuxedo)

Last Answer : That's absolutely great, but I'll focus more on that in the evening. It reminds me of Cremon's shape when calculating a lattice girder. I wouldn't be able to do it anymore, I'll have to revive my memory :) I'm adding - Ary, could the video be downloaded somewhere?

How do you calculate the government purchases multiplier?

Description : How do you calculate the government purchases multiplier?

Last Answer : Need answer

How does the multiplier effect help our economy?

Description : How does the multiplier effect help our economy?

Last Answer : Feel Free to Answer

What type of money does The money multiplier effect shows that when a bank has a lower reserve rate they are able to generate what money?

Description : What type of money does The money multiplier effect shows that when a bank has a lower reserve rate they are able to generate what money?

Last Answer : Need answer

What is the decimal multiplier to decrease by 11?

Description : What is the decimal multiplier to decrease by 11?

Last Answer : Suppose m is the required multiplier.Then multiplication by m would increase any x by 11, that is, x * m = x + 11 for all x x * m - x = 11 x*(m - 1) = 11 m - 1 = 11/x m = 1 + 11/x But that means that m is not defined for x = 0 and there is a different m for every non-zero x.

The money multiplier formula _____.?

Description : The money multiplier formula _____.?

Last Answer : determines the amount of new money that will be created with each demand deposit

If the money multiplier is 4, what is the required reserve ratio (RRR)?

Description : If the money multiplier is 4, what is the required reserve ratio (RRR)?

Last Answer : 25 percent