A 10 bit resistive divider is constructed such that the current through...

A 10 bit resistive divider is constructed such that the current through the LSB resistor is 100μA. The maximum current that will flow through the MSB resistor is 
by

1 Answer

Answer :

A 10 bit resistive divider is constructed such that the current through the LSB resistor is 100μA. The maximum current that will flow through the MSB resistor is 51.2mA.

by

Related questions

If the source voltage for the voltage divider in question 50 supplies 150 volts, what is the total current through the voltage divider?

Description : If the source voltage for the voltage divider in question 50 supplies 150 volts, what is the total current through the voltage divider?

Last Answer : 495 mA.

If a voltage divider is required for a load that will use 450 mA of current, what should be the value of bleeder current?

Description : If a voltage divider is required for a load that will use 450 mA of current, what should be the value of bleeder current?

Last Answer : 45 mA rule-of-thumb.

Current divider rule

Description : Current divider rule

Last Answer : Current divider rule

Indicate the false statement A. The noise generated in a resistance or the resistive component of any impedance is random. B. Random noise power is proportional to the bandwidth over which is measured C. A random voltage across the resistor does not exist D. All formula referring to random noise are applicable only to the value of such noise.

Description : Indicate the false statement A. The noise generated in a resistance or the resistive component of any impedance is random. B. Random noise power is proportional to the bandwidth over which is measured ... exist D. All formula referring to random noise are applicable only to the value of such noise.

Last Answer : C. A random voltage across the resistor does not exist

Does a little bit of rain or snow damage a building being constructed?

Description : Does a little bit of rain or snow damage a building being constructed?

Last Answer : Like mold.

Voltage will always lead current in a/an ______________. A. capacitive circuit B. inductive circuit C. magnetic circuit D. resistive circuit

Description : Voltage will always lead current in a/an ______________. A. capacitive circuit B. inductive circuit C. magnetic circuit D. resistive circuit

Last Answer : Answer: B

Which of the following statements concerning AC circuits is correct? A. The power factor of a resistive circuit is always zero. B. True power in an inductive circuit always equals apparent power. C. Inductive reactance varies directly with the frequency and the inductance. D. Total opposition to the flow of alternating current depends upon the amount of reactive power.

Description : Which of the following statements concerning AC circuits is correct? A. The power factor of a resistive circuit is always zero. B. True power in an inductive circuit always equals apparent power. ... . D. Total opposition to the flow of alternating current depends upon the amount of reactive power.

Last Answer : Answer: C

What kind of effect is referred to a varying light producing a varying voltage output of a detector? A. Current effect B. Voltage effect C. Resistive effect D. Photovoltaic effect

Description : What kind of effect is referred to a varying light producing a varying voltage output of a detector? A. Current effect B. Voltage effect C. Resistive effect D. Photovoltaic effect

Last Answer : D. Photovoltaic effect

Give the circuit analysis of current source inverter with resistive load.

Description : Give the circuit analysis of current source inverter with resistive load. What are the main difference between voltage source inverter and current source inverter?

Last Answer : Current source inverter (CSI): In current source inverter, the output current is independent of load. The input current of current source inverter is constant. Current source converter converts DC input current to ... are connected in parallel. In CSI diodes are connected in series.

What is a voltage divider in Arduino?

Description : What is a voltage divider in Arduino?

Last Answer : A voltage divider in Arduino is a circuit that divides a voltage into smaller values using two resistors.

Do you prefer an "open floor plan," or do you prefer some sort of divider between rooms?

Description : Do you prefer an "open floor plan," or do you prefer some sort of divider between rooms?

Last Answer : answer:I love toying with designing my own space and as a former int. design and home staging asst. I have many ideas. Now days after raising a family and being single/divorced for years I prefer an ... apartment soon on a large property and am very excited about how I will set things up. :-)

Is it legal to park at the median divider on Sundays in San Francisco?

Description : Is it legal to park at the median divider on Sundays in San Francisco?

Last Answer : I’m not from San Francisco, but I can’t imagine it would ever be legal to park on a median divider – no matter what day or time it is. People tend to park wherever it’s convenient to them… one parks there and others follow suit.

Plant shelving that could serve as a room divider: what am I talking about?

Description : Plant shelving that could serve as a room divider: what am I talking about?

Last Answer : Etagere?

A variable shunt, connected across the series field coils of a DC compound wound generator, to permit adjustment of the degree of compounding, is called a _____________. A. divider B. diverter C. converter D. rheostat

Description : A variable shunt, connected across the series field coils of a DC compound wound generator, to permit adjustment of the degree of compounding, is called a _____________. A. divider B. diverter C. converter D. rheostat

Last Answer : Answer: B

What circuit is responsible in activating and deactivating adjacent antenna elements in a mobile satellite array? A. Radial divider B. Divider/combiner C. Radial combiner D. Radial multiplexer

Description : What circuit is responsible in activating and deactivating adjacent antenna elements in a mobile satellite array? A. Radial divider B. Divider/combiner C. Radial combiner D. Radial multiplexer

Last Answer : A. Radial divider

Which of the following is the basic synthesizer circuit? A. Frequency divider B. Frequency multiplier C. PLL D. Mixer

Description : Which of the following is the basic synthesizer circuit? A. Frequency divider B. Frequency multiplier C. PLL D. Mixer

Last Answer : C. PLL

What is the difference between resistor, rheostat and potential divider?

Description : What is the difference between resistor, rheostat and potential divider?

Last Answer : Resistor: a fixed resistance connected permanently in the circuit for limiting the current to definite value is called the resistor. Rheostat: a variable resistance by sliding contacts on it the current can ... : when a resistance is used to develop a voltage drop it is called a potential divider.

In vertical conveyor reaper, the crop to be harvested are guided by a) Star wheel b) Reel c) Row divider d) Cutter bar

Description : In vertical conveyor reaper, the crop to be harvested are guided by a) Star wheel b) Reel c) Row divider d) Cutter bar

Last Answer : Star wheel

If the load requirement consists of both positive and negative voltages, what technique is used in the voltage divider to supply the loads from a single voltage source?

Description : If the load requirement consists of both positive and negative voltages, what technique is used in the voltage divider to supply the loads from a single voltage source?

Last Answer : The ground (reference point) is placed in the proper point in the voltage divider so that positive and negative voltages are supplied

What information must be known to determine the component values for a voltage divider?

Description : What information must be known to determine the component values for a voltage divider?

Last Answer : The source voltage and load requirements (voltage and current).

Circuit which gives continuously varying potential is called a. complex network b. wheat stone bridge c. potential divider d. all of above

Description : Circuit which gives continuously varying potential is called a. complex network b. wheat stone bridge c. potential divider d. all of above

Last Answer : c. potential divider

Explain with circuit diagram, voltage divider biasing method and state its two advantages.

Description : Explain with circuit diagram, voltage divider biasing method and state its two advantages.

Last Answer : a)Here R1 and R2 forms voltage divider biasing arrangement. b)voltage drop across R2 ,forward biases the base emitter junction. c)so base current flows and hence collector ... Operating point stabilized against shift in temperature. · Operating point is almost independent of β variation

Voltage divider rule

Description : Voltage divider rule

Last Answer : Voltage divider rule

Draw circuit diagram of voltage divider biasing list two advantages of voltage divider biasing of BJT.

Description : Draw circuit diagram of voltage divider biasing list two advantages of voltage divider biasing of BJT.

Last Answer : Two advantages of voltage divider biasing of BJT. 1. It is very simple method of transistor biasing. 2. The biasing conditions can be very easily set. 3. there is no loading of ... 5. The resistor RE introduces a negative feedback. So all the advantages of negative feedback are obtained. 

The disadvantage of voltage divider bias is that

Description : The disadvantage of voltage divider bias is that  1. it has a high stability factor 2. it has many resistors 3. it allows thermal runaway 4. it does not allow faithful amplification

Last Answer : Is the power off this word only current 

A potential divider is normally connected _____________.

Last Answer : A potential divider is normally connected outside the generator circuit towards the load circuit.

A voltage divider is always a _____

Last Answer : A voltage divider is always a series circuit.

1. What does the Preamble of our Constitution contin? 2. Which will you put into pure water in order to pass electric current through it? 3. Of the various ways of financing government’s investment expenditure, what is the least inflationary? 4. In which country are ‘Dykes’ especially constructed? 5. What was Sher Shah’s real name?

Description : 1. What does the Preamble of our Constitution contin? 2. Which will you put into pure water in order to pass electric current through it? 3. Of the various ways of financing government's ... pollution? 19. Which Strait separates Asia from North America? 20. Who was contemporary of Namdev?

Last Answer : Answer : 1. The spirit of the Constitution 2. Lemon Juice 3. Taxation 4. Norway 5. Farid 6. Ahmedabad 7. Warming effect 8. Uttar Pradesh 9. Grand Canyon 10. Second Battle of Tarain 11. ... 15. Iltutmish 16. Chloroplasts 17. Single Transferable Vote System 18. Hydrogen 19. The Bering Strait 20. Sena

For a certain 4 bit successive approximation A/D converter, the maximum ...

Last Answer : For a certain 4 bit successive approximation A/D converter, the maximum ladder output is +8V. if a constant +6V is applied to the analog input the sequence of binary states for the SA register is 0110.

A 12 bit counter type A/D converter uses a 1 MHz clock. If the full scale output is +10V, its resolution output is

Last Answer : A 12 bit counter type A/D converter uses a 1 MHz clock. If the full scale output is +10V, its resolution output is 2.44mV.

The resolution of a 12 bit D/A converter using a binary ladder is

Last Answer : The resolution of a 12 bit D/A converter using a binary ladder is 0.02%.

The conversion time of a 12 bit successive approximation A/D converter using a 1 MHz clock is

Last Answer : The conversion time of a 12 bit successive approximation A/D converter using a 1 MHz clock is 12μs.

An 8 bit converter type A/D converter makes at least 8000conversions/sec. The clock frequency used is

Last Answer : An 8 bit converter type A/D converter makes at least 8000conversions/sec. The clock frequency used is 2MHz.

A 12 bit counter type A/D converter uses a 1 MHz clock. Its maximum conversion time is

Last Answer : A 12 bit counter type A/D converter uses a 1 MHz clock. Its maximum conversion time is 4096μs.

Such wells (Unlined) are constructed normally in areas.......a. Where the water table is low c. Where the farmer is affluent available.

Description : Such wells (Unlined) are constructed normally in areas.......a. Where the water table is low c. Where the farmer is affluent available.

Last Answer : b. Where the water table is high.

What is the power factor in pure resistive , capacitive , inductive load ?

Description : What is the power factor in pure resistive , capacitive , inductive load ?

Last Answer : Answer : Power factor cosΦ = 1 in pure resistive load, cosΦ = 0 in capacitive load , cosΦ = 0 in inductive load .

Which resistive value is comparatively higher ?

Description : Which resistive value is comparatively higher ?

Last Answer : The value of equivalent resistance is greater than any resistance

Figure below shows a block of mass 35 kg resting on a table. The table is so rough that it offers a self adjusting resistive force 10%

Description : Figure below shows a block of mass 35 kg resting on a table. The table is so rough that it offers a self adjusting resistive force 10%

Last Answer : Figure below shows a block of mass 35 kg resting on a table. The table is so rough that it ... so that the block does not slide along the table?

Is computer is Resistive load?

Description : Is computer is Resistive load?

Last Answer : It is resistive much load

Capacitors can be used in electric distribution systems to improve power factor. This is accomplished by seesawing energy between the capacitor and the _____________. A. generator B. inductive loads C. resistive loads D. all of the above

Description : Capacitors can be used in electric distribution systems to improve power factor. This is accomplished by seesawing energy between the capacitor and the _____________. A. generator B. inductive loads C. resistive loads D. all of the above

Last Answer : Answer: B

The existing resistance of a conductor is dependent upon its length, cross-sectional area, _____________. A. temperature and insulation B. material and insulation C. resistive coefficient and material D. material and temperature

Description : The existing resistance of a conductor is dependent upon its length, cross-sectional area, _____________. A. temperature and insulation B. material and insulation C. resistive coefficient and material D. material and temperature

Last Answer : Answer: D

When using an ohmmeter to test a semiconductor diode, you find a low resistance in both the forward and reverse bias directions. This indicates that the diode has a/an ____________. A. open B. short C. good resistive quality D. good capacitive quality

Description : When using an ohmmeter to test a semiconductor diode, you find a low resistance in both the forward and reverse bias directions. This indicates that the diode has a/an ____________. A. open B. short C. good resistive quality D. good capacitive quality

Last Answer : Answer: B

For an Resistive Load and Inductive load considered for switching operation of circuit breaker, Switching of which load is difficult and Why?

Description : For an Resistive Load and Inductive load considered for switching operation of circuit breaker, Switching of which load is difficult and Why?

Last Answer : In case of switching resistive load, current and voltage will be in phase i.e,when during current zero voltage also will be zero in case of resistive load. Hence the voltage at the ... maximum. This results in re-striking of arc once again. Therefore switching inductive load will be difficult

Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Description : Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Last Answer : D. To prevent re-radiation of the local oscillator

How the starting winding is made resistive?

Description : How the starting winding is made resistive?

Last Answer : It consists of only few turns of smaller diameter.

The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance C. reducing the input power to below its critical level. D. an impedance mismatch between the load and the line.

Description : The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance ... input power to below its critical level. D. an impedance mismatch between the load and the line.

Last Answer : D. an impedance mismatch between the load and the line.

An RG-11/U foam coaxial cable has a maximum voltage standing wave of 52 V and a minimum voltage of 17 V. Find the value of the resistive load. A. 24.59Ω B. Either A or C C. 228.75Ω D. Neither A nor C

Description : An RG-11/U foam coaxial cable has a maximum voltage standing wave of 52 V and a minimum voltage of 17 V. Find the value of the resistive load. A. 24.59Ω B. Either A or C C. 228.75Ω D. Neither A nor C

Last Answer : B. Either A or C

Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Description : Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Last Answer : C. resistive load at the resonant frequency

The ratio of the actual damping coefficient (c) to the critical damping coefficient (cc ) is known as _________ A Damping factor B Damping coefficient C Resistive factor D Resistive coefficient

Description : The ratio of the actual damping coefficient (c) to the critical damping coefficient (cc ) is known as _________ A Damping factor B Damping coefficient C Resistive factor D Resistive coefficient

Last Answer : A Damping factor