Why is detector saturation not generally a problem in fiber optic communications systems?

Why is detector saturation not generally a problem in fiber  optic communications systems?
by

1 Answer

Answer :

Because fiber optic communications systems operate at low  optical power levels.
by

Related questions

What type of modulation do most analog fiber optic communications systems use?

Description : What type of modulation do most analog fiber optic communications systems use?

Last Answer : Intensity modulation.

The most common device used as a light detector in fiber optic communications system. A. LED B. Darlington phototransistor C. APDs D. PIN diode

Description : The most common device used as a light detector in fiber optic communications system. A. LED B. Darlington phototransistor C. APDs D. PIN diode

Last Answer : C. APDs

Which types of LEDs are the preferred optical sources for short-distance, low-data-rate fiber optic systems?

Description : Which types of LEDs are the preferred optical sources for short-distance, low-data-rate fiber optic systems?

Last Answer : SLEDs and ELEDs.

List the two principal optical detectors used in fiber optic systems.

Description : List the two principal optical detectors used in fiber optic systems.

Last Answer : The semiconductor positive-intrinsic-negative (PIN) photodiode and avalanche photodiode (APD).

List five precautions to take when installing fiber optic systems on board naval ships.

Description : List five precautions to take when installing fiber optic systems on board naval ships.

Last Answer : a. Never bend an optical fiber or cable at a radius of curvature less than the minimum bend radius. b. Never pull fiber optic cables tight or fasten them over or through sharp corners or ... the hardware. e. Allow only trained, authorized personnel to install or repair fiber optic systems.

In fiber optic systems, designers consider what trade-offs?

Description : In fiber optic systems, designers consider what trade-offs?

Last Answer : Trade-offs in fiber properties, types of connections, optical sources, and detector types in military and subscriber-loop applications.

Why is it generally only necessary to refer to point-to-point data links when discussing the process of fiber optic system design?

Description : Why is it generally only necessary to refer to point-to-point data links when discussing the process of fiber optic system design?

Last Answer : Because fiber optic systems that incorporate complex architectures can be simplified into a collection of point-to-point data links before beginning the design process.

If a fiber optic system has a rise time of 38.55 ns, the source rise time is 12 ns and the detector rise time is 12 ns, what is the cable rise time? A. 34.61 ns B. 14.55 ns C. 52.55 ns D. 26.25 ns

Description : If a fiber optic system has a rise time of 38.55 ns, the source rise time is 12 ns and the detector rise time is 12 ns, what is the cable rise time? A. 34.61 ns B. 14.55 ns C. 52.55 ns D. 26.25 ns

Last Answer : A. 34.61 ns

If a fiber optic system has a rise time of 16 ns, the source rise time is 1.5 ns and the detector rise time is 2 ns, what is the cable rise time? A. 14 ns B. 6 ns C. 9 ns D. 12.5 ns

Description : If a fiber optic system has a rise time of 16 ns, the source rise time is 1.5 ns and the detector rise time is 2 ns, what is the cable rise time? A. 14 ns B. 6 ns C. 9 ns D. 12.5 ns

Last Answer : A. 14 ns

ECE Board Exam March 1996 It is a spacecraft placed in orbit around the earth carrying onboard microwave receiver and transmitting equipments. A. Fiber optic equipment B. Communications satellite C. Wireless radio system D. Coaxial cable syste

Description : ECE Board Exam March 1996 It is a spacecraft placed in orbit around the earth carrying onboard microwave receiver and transmitting equipments. A. Fiber optic equipment B. Communications satellite C. Wireless radio system D. Coaxial cable syste

Last Answer : B. Communications satellite

______ cable is used for voice and data communications. A) Coaxial B) Fiber-optic C) Twisted-pair D) none of the above

Description : ______ cable is used for voice and data communications. A) Coaxial B) Fiber-optic C) Twisted-pair D) none of the above

Last Answer : Twisted-pair

……….cable is used for voice and data communications. a. Twisted-pair b. None of These c. Coaxial d. Fiber-optic

Description : ……….cable is used for voice and data communications. a. Twisted-pair b. None of These c. Coaxial d. Fiber-optic

Last Answer : a. Twisted-pair

What is the difference between passive and active fiber optic couplers?

Description : What is the difference between passive and active fiber optic couplers?

Last Answer : Passive couplers redistribute optical signals without optical-to electrical conversion.

The Navy classifies fiber optic connectors in what two ways?

Description : The Navy classifies fiber optic connectors in what two ways?

Last Answer : Light-duty and heavy-duty connectors.

Which type of fiber optic connector (butt-jointed or expanded beam) brings the prepared ends of two optical fibers into close contact?

Description : Which type of fiber optic connector (butt-jointed or expanded beam) brings the prepared ends of two optical fibers into close contact?

Last Answer : Butt-jointed connectors.

Fiber optic connectors can reduce system performance by increasing what two types of noise?

Description : Fiber optic connectors can reduce system performance by increasing what two types of noise?

Last Answer : Modal and reflection.

What connection properties result in fiber optic connector coupling loss?

Description : What connection properties result in fiber optic connector coupling loss?

Last Answer : Poor fiber alignment and end preparation, fiber mismatches, and Fresnel reflection.

Define a fiber optic splice.

Description : Define a fiber optic splice.

Last Answer : A permanent fiber joint whose purpose is to establish an optical connection between two individual optical fibers.

Which fiber optic component (splice, connector, or coupler) makes a permanent connection in a distributed system?

Description : Which fiber optic component (splice, connector, or coupler) makes a permanent connection in a distributed system?

Last Answer : Splice.

List five common fiber optic transmitter packages.

Description : List five common fiber optic transmitter packages.

Last Answer : TO can, DIP, butterfly lead microcircuits, circuit cards, and stand-alone optical fiber converters.

What are the two types of output interfaces for fiber optic transmitters?

Description : What are the two types of output interfaces for fiber optic transmitters?

Last Answer : Optical connectors and optical fiber pigtails.

Which part of a fiber optic transmitter converts the processed electrical signal to an optical signal?

Description : Which part of a fiber optic transmitter converts the processed electrical signal to an optical signal?

Last Answer : The optical source.

What are the three parts of a fiber optic transmitter?

Description : What are the three parts of a fiber optic transmitter?

Last Answer : Interface circuit, source drive circuit, and an optical source.

What are the two basic types of preamplifiers used in fiber optic receivers?

Description : What are the two basic types of preamplifiers used in fiber optic receivers?

Last Answer : The high-impedance amplifier and the transimpedance amplifier.

What is a fiber optic receiver?

Description : What is a fiber optic receiver?

Last Answer : An electro-optic device that accepts optical signals from an optical fiber and converts them into electrical signals

List the types of fiber optic components considered part of a fiber optic cable plant.

Description : List the types of fiber optic components considered part of a fiber optic cable plant.

Last Answer : Optical fiber cables, connectors, splices, mounting panels, jumper cables, and other passive components.

List four system topologies that can be constructed using point-to-point fiber optic links.

Description : List four system topologies that can be constructed using point-to-point fiber optic links.

Last Answer : Linear bus, ring, star, and tree topologies.

What is the main disadvantage of using fiber-optic cables?

Description : What is the main disadvantage of using fiber-optic cables?

Last Answer : High attenuation.

What effect does noise have on the fiber optic signal?

Description : What effect does noise have on the fiber optic signal?

Last Answer : Noise obscures or reduces the quality of the signal.

List the three parts of a fiber optic data link

Description : List the three parts of a fiber optic data link

Last Answer : Transmitter, optical fiber, and receiver.

Describe the basic functions of a fiber optic data link

Description : Describe the basic functions of a fiber optic data link

Last Answer : The basic functions of a fiber optic data link are to convert an electrical input signal to an optical signal, send the optical signal over an optical fiber, and convert the optical signal back to an electrical signal.

Which of the following is not a common application of fiber-optic cable? a. Computer networks b. Long-distance telephone systems c. Closed circuit TV d. Consumer TV

Description : Which of the following is not a common application of fiber-optic cable? a. Computer networks b. Long-distance telephone systems c. Closed circuit TV d. Consumer TV

Last Answer : d. Consumer TV

Which of the following is not a common application of fiber-optic cable? ∙ a. Computer networks ∙ b. Long-distance telephone systems ∙ c. Closed circuit TV ∙ d. Consumer TV

Description : Which of the following is not a common application of fiber-optic cable? ∙ a. Computer networks ∙ b. Long-distance telephone systems ∙ c. Closed circuit TV ∙ d. Consumer TV

Last Answer : d. Consumer TV

Why can multimode graded-index fiber 1300-nm systems using LEDs operate over longer distances and at higher bandwidths than 850-nm systems?

Description : Why can multimode graded-index fiber 1300-nm systems using LEDs operate over longer distances and at higher bandwidths than 850-nm systems?

Last Answer : Longer distances and higher bandwidths are possible because fiber material losses and dispersion are significantly reduced at the 1300-nm region.

Modal dispersion affects the bandwidth of multimode systems. It is essential to adjust what three fiber properties to maximize system bandwidth?

Description : Modal dispersion affects the bandwidth of multimode systems. It is essential to adjust what three fiber properties to maximize system bandwidth?

Last Answer : Core diameter, NA, and index profile properties.

List seven advantages of fiber optics over electrical systems.

Description : List seven advantages of fiber optics over electrical systems.

Last Answer : Advantages of fiber optics are improved system performance, immunity to electrical noise, signal security, electrical isolation, reduced size and w

Will fiber coupling loss generally increase or decrease if the mode field diameter of a single mode fiber is decreased?

Description : Will fiber coupling loss generally increase or decrease if the mode field diameter of a single mode fiber is decreased?

Last Answer : Increase.

When connector losses, splice losses and coupler losses are added, what is the limiting factor? ∙ A. source power ∙ B. fiber attenuation ∙ C. connector and splice loss ∙ D. detector sensitivity

Description : When connector losses, splice losses and coupler losses are added, what is the limiting factor? ∙ A. source power ∙ B. fiber attenuation ∙ C. connector and splice loss ∙ D. detector sensitivity

Last Answer : D. detector sensitivity

How can modal dispersion reduced entirely? ∙ A. Use a graded index fiber ∙ B. Use a single-mode fiber ∙ C. Use a monochromatic light source ∙ D. Use a very sensitive light detector

Description : How can modal dispersion reduced entirely? ∙ A. Use a graded index fiber ∙ B. Use a single-mode fiber ∙ C. Use a monochromatic light source ∙ D. Use a very sensitive light detector

Last Answer : Use a single-mode fiber

Chromatic dispersion can be eliminated by __________. ∙ A. using a monochromatic light source ∙ B. using a very small numerical aperture fiber ∙ C. using a graded-index fiber ∙ D. using a very sensitive photo detector

Description : Chromatic dispersion can be eliminated by __________. ∙ A. using a monochromatic light source ∙ B. using a very small numerical aperture fiber ∙ C. using a graded-index fiber ∙ D. using a very sensitive photo detector

Last Answer : A. using a monochromatic light source

When connectorlosses,splice losses, and couplerlosses are added,whatisthe finallimitingfactor? a. Source power b. Fiber attenuation c. Connector and splice losses d. Detector sensitivity

Description : When connectorlosses,splice losses, and couplerlosses are added,whatisthe finallimitingfactor? a. Source power b. Fiber attenuation c. Connector and splice losses d. Detector sensitivity

Last Answer : d. Detector sensitivity

Sound waves transmitted from a source are sometimes weak when they reach the detector. What instrument is needed to boost the weak signal?

Description : Sound waves transmitted from a source are sometimes weak when they reach the detector. What instrument is needed to boost the weak signal?

Last Answer : An amplifier.

In the output of an ac error detector, what indicates the (a) direction and (b) amount of control necessary for correspondence?

Description : In the output of an ac error detector, what indicates the (a) direction and (b) amount of control necessary for correspondence?

Last Answer : (a) Phase. (b) Amplitude.

An error signal is the difference between what two quantities fed to the CT (error detector)?

Description : An error signal is the difference between what two quantities fed to the CT (error detector)?

Last Answer : Input signal and feedback.

What are the four most common materials used in semiconductor detector fabrication?

Description : What are the four most common materials used in semiconductor detector fabrication?

Last Answer : Silicon, gallium arsenide, germanium, and indium phosphide.

For efficient operation, should a detector have a high or low responsivity at the operating wavelength?

Description : For efficient operation, should a detector have a high or low responsivity at the operating wavelength?

Last Answer : High.

Describe the operation of an optical detector

Description : Describe the operation of an optical detector

Last Answer : It is a transducer that converts an optical signal into an electrical signal. It does this by generating an electrical current proportional to the intensity of incident optical radiation.

What is the function of the detector?

Description : What is the function of the detector?

Last Answer : To extract the modulating audio signal.

How can a peak detector for pam be modified to detect pdm?

Description : How can a peak detector for pam be modified to detect pdm?

Last Answer : By making the time constant for charging the capacitor at least 10 times the maximum received pulse width.

What is the time constant of the resistor and capacitor in a peak detector for pam?

Description : What is the time constant of the resistor and capacitor in a peak detector for pam?

Last Answer : At least 10 times the interpulse period.