When connectorlosses,splice losses, and couplerlosses are added,whatisthe finallimitingfactor? a. Source power b. Fiber attenuation c. Connector and splice losses d. Detector sensitivity

When connectorlosses,splice losses, and couplerlosses are added,whatisthe finallimitingfactor? a. Source power  
b. Fiber attenuation
c. Connector and splice losses
d. Detector sensitivity
by

1 Answer

Answer :

d. Detector sensitivity
by

Related questions

When connector losses, splice losses and coupler losses are added, what is the limiting factor? ∙ A. source power ∙ B. fiber attenuation ∙ C. connector and splice loss ∙ D. detector sensitivity

Description : When connector losses, splice losses and coupler losses are added, what is the limiting factor? ∙ A. source power ∙ B. fiber attenuation ∙ C. connector and splice loss ∙ D. detector sensitivity

Last Answer : D. detector sensitivity

The mechanical splice is best suited for ∙ A. quicker installation under ideal condition ∙ B. minimum attenuation losses ∙ C. field service conditions ∙ D. situations in which cost of equipment is not a factor

Description : The mechanical splice is best suited for ∙ A. quicker installation under ideal condition ∙ B. minimum attenuation losses ∙ C. field service conditions ∙ D. situations in which cost of equipment is not a factor

Last Answer : D. situations in which cost of equipment is not a factor

Whatisthe frequencylimitof copperwire? a. approximately 0.5 MHz b. approximately 1.0 MHz c. approximately 40 GHz d. None of the above

Description : Whatisthe frequencylimitof copperwire? a. approximately 0.5 MHz b. approximately 1.0 MHz c. approximately 40 GHz d. None of the above

Last Answer : b. approximately 1.0 MHz

Which fiber optic component (splice, connector, or coupler) makes a permanent connection in a distributed system?

Description : Which fiber optic component (splice, connector, or coupler) makes a permanent connection in a distributed system?

Last Answer : Splice.

Themechanicalsplice isbestsuited for a. quicker installation under ideal conditions b. minimum attenuation losses c. field service conditions d. situations in which cost of equipment is not a factor

Description : Themechanicalsplice isbestsuited for a. quicker installation under ideal conditions b. minimum attenuation losses c. field service conditions d. situations in which cost of equipment is not a factor

Last Answer : c. field service conditions

The term power budgeting refers to ∙ A. the cost of cable, connectors, equipment and installation ∙ B. the loss of power due to defective components ∙ C. the total power available minus the attenuation losses ∙ D. the comparative costs of fiber and copper installations

Description : The term power budgeting refers to ∙ A. the cost of cable, connectors, equipment and installation ∙ B. the loss of power due to defective components ∙ C. the total power available minus the attenuation losses ∙ D. the comparative costs of fiber and copper installations

Last Answer : C. the total power available minus the attenuation losses

Why are visible-light LEDs not used for fiber optics? ∙ a. It has high losses ∙ b. It has short wave ∙ c. It has low attenuation ∙ d. It has weak signal

Description : Why are visible-light LEDs not used for fiber optics? ∙ a. It has high losses ∙ b. It has short wave ∙ c. It has low attenuation ∙ d. It has weak signal

Last Answer : ∙ a. It has high losses

The mechanical splice attenuation loss is _____ dB or less ∙ a. 0.1 ∙ b. 0.01 ∙ c. 0.001 ∙ d. 1

Description : The mechanical splice attenuation loss is _____ dB or less ∙ a. 0.1 ∙ b. 0.01 ∙ c. 0.001 ∙ d. 1

Last Answer : a. 0.1

How is fiber sensitivity to bending losses reduced?

Description : How is fiber sensitivity to bending losses reduced?

Last Answer : Fiber sensitivity to bending losses can be reduced if the refractive index of the core is increased and/or if the overall diameter of the fiber increases.

As electromagneticwavestravelinfree space, onlyone ofthefollowingcan happento them: a. absorption b. attenuation c. refraction d. reflection

Description : As electromagneticwavestravelinfree space, onlyone ofthefollowingcan happento them: a. absorption b. attenuation c. refraction d. reflection

Last Answer : b. attenuation

Used to test a fiber optics splice ∙ a. Spectrum analyzer ∙ b. Oscilloscope ∙ c. Optical power meter ∙ d. Field strength meter

Description : Used to test a fiber optics splice ∙ a. Spectrum analyzer ∙ b. Oscilloscope ∙ c. Optical power meter ∙ d. Field strength meter

Last Answer : c. Optical power meter

The minimum optical power a light detector can receive and still produce a usable electrical output signal. ∙ A. light responsivity ∙ B. light sensitivity ∙ C. light collectivity ∙ D. illumination

Description : The minimum optical power a light detector can receive and still produce a usable electrical output signal. ∙ A. light responsivity ∙ B. light sensitivity ∙ C. light collectivity ∙ D. illumination

Last Answer : B. light sensitivity

What is the average insertion loss of fusion splice in fiber optics? a. 0.09dB b. 0.9dB c. 0.19dB d. 0.009dB

Description : What is the average insertion loss of fusion splice in fiber optics? a. 0.09dB b. 0.9dB c. 0.19dB d. 0.009dB

Last Answer : a. 0.09dB

What fiber property directly affects splice loss in fusion splicing?

Description : What fiber property directly affects splice loss in fusion splicing?

Last Answer : The angles and quality of the two fiber-end faces.

Define a fiber optic splice.

Description : Define a fiber optic splice.

Last Answer : A permanent fiber joint whose purpose is to establish an optical connection between two individual optical fibers.

What is the average loss in fiber splice? ∙ a. 0.10 dB ∙ b. 0.15 dB ∙ c. 0.20 dB ∙ d. 0.25 dB

Description : What is the average loss in fiber splice? ∙ a. 0.10 dB ∙ b. 0.15 dB ∙ c. 0.20 dB ∙ d. 0.25 dB

Last Answer : 0.15 dB

What is the average insertion loss of fusion splice in fiber optics? ∙ a. 0.09 dB ∙ b. 0.9 dB ∙ c. 0.19 dB ∙ d. 0.009 dB

Description : What is the average insertion loss of fusion splice in fiber optics? ∙ a. 0.09 dB ∙ b. 0.9 dB ∙ c. 0.19 dB ∙ d. 0.009 dB

Last Answer : ∙ b. 0.9 dB

The loss in single-mode fiber-optic cable due to a splice is about: a. 0.02 dB b. 0.2 dB c. 1 dB d. 3 dB

Description : The loss in single-mode fiber-optic cable due to a splice is about: a. 0.02 dB b. 0.2 dB c. 1 dB d. 3 dB

Last Answer : a. 0.02 dB

If a fiber optic system has a rise time of 38.55 ns, the source rise time is 12 ns and the detector rise time is 12 ns, what is the cable rise time? A. 34.61 ns B. 14.55 ns C. 52.55 ns D. 26.25 ns

Description : If a fiber optic system has a rise time of 38.55 ns, the source rise time is 12 ns and the detector rise time is 12 ns, what is the cable rise time? A. 34.61 ns B. 14.55 ns C. 52.55 ns D. 26.25 ns

Last Answer : A. 34.61 ns

If a fiber optic system has a rise time of 16 ns, the source rise time is 1.5 ns and the detector rise time is 2 ns, what is the cable rise time? A. 14 ns B. 6 ns C. 9 ns D. 12.5 ns

Description : If a fiber optic system has a rise time of 16 ns, the source rise time is 1.5 ns and the detector rise time is 2 ns, what is the cable rise time? A. 14 ns B. 6 ns C. 9 ns D. 12.5 ns

Last Answer : A. 14 ns

How can modal dispersion reduced entirely? ∙ A. Use a graded index fiber ∙ B. Use a single-mode fiber ∙ C. Use a monochromatic light source ∙ D. Use a very sensitive light detector

Description : How can modal dispersion reduced entirely? ∙ A. Use a graded index fiber ∙ B. Use a single-mode fiber ∙ C. Use a monochromatic light source ∙ D. Use a very sensitive light detector

Last Answer : Use a single-mode fiber

Chromatic dispersion can be eliminated by __________. ∙ A. using a monochromatic light source ∙ B. using a very small numerical aperture fiber ∙ C. using a graded-index fiber ∙ D. using a very sensitive photo detector

Description : Chromatic dispersion can be eliminated by __________. ∙ A. using a monochromatic light source ∙ B. using a very small numerical aperture fiber ∙ C. using a graded-index fiber ∙ D. using a very sensitive photo detector

Last Answer : A. using a monochromatic light source

The loss in signal power as light travels down a fiber is called a. Dispersion b. Scattering c. Absorption d. Attenuation

Description : The loss in signal power as light travels down a fiber is called a. Dispersion b. Scattering c. Absorption d. Attenuation

Last Answer : d. Attenuation

ECE Board Exam November 1996 The loss in signal power as light travels down a fiber is A. attenuation B. propagation C. absorption D. scattering

Description : ECE Board Exam November 1996 The loss in signal power as light travels down a fiber is A. attenuation B. propagation C. absorption D. scattering

Last Answer : A. attenuation

The loss in signal power as light travels down the fiber is called a. attenuation b. progragation c. scattering d. interruption

Description : The loss in signal power as light travels down the fiber is called a. attenuation b. progragation c. scattering d. interruption

Last Answer : attenuation

The loss in signal power as light travels down the fiber is called ............. A) Attenuation B) Propagation C) Scattering D) Interruption

Description : The loss in signal power as light travels down the fiber is called ............. A) Attenuation B) Propagation C) Scattering D) Interruption

Last Answer : A) Attenuation

Band loss is ∙ a. A reduction in transmitter power caused by earth’s surface curvature ∙ b. A reduction in strength of the signal caused by folded dipole bends ∙ c. An attenuation increase caused by bends radiating from the side of the fiber ∙ d. All of these

Description : Band loss is ∙ a. A reduction in transmitter power caused by earth’s surface curvature ∙ b. A reduction in strength of the signal caused by folded dipole bends ∙ c. An attenuation increase caused by bends radiating from the side of the fiber ∙ d. All of these

Last Answer : c. An attenuation increase caused by bends radiating from the side of the fiber

The loss in signal power as light travels down a fiber is called ∙ a. Dispersion ∙ b. Scattering ∙ c. Absorption ∙ d. Attenuation

Description : The loss in signal power as light travels down a fiber is called ∙ a. Dispersion ∙ b. Scattering ∙ c. Absorption ∙ d. Attenuation

Last Answer : ∙ d. Attenuation

The loss in signal power as light travels down the fiber is called ............. A) Attenuation B) Propagation C) Scattering D) Interruption

Description : The loss in signal power as light travels down the fiber is called ............. A) Attenuation B) Propagation C) Scattering D) Interruption

Last Answer : A) Attenuation

The loss in signal power as light travels down the fiber is called ............. A) Attenuation B) Propagation C) Scattering D) Interruption

Description : The loss in signal power as light travels down the fiber is called ............. A) Attenuation B) Propagation C) Scattering D) Interruption

Last Answer : A) Attenuation

Which optical detector is used when high sensitivity and bandwidth are required? ∙ a. PMT ∙ b. APD ∙ c. PIN ∙ d. Phototransistor

Description : Which optical detector is used when high sensitivity and bandwidth are required? ∙ a. PMT ∙ b. APD ∙ c. PIN ∙ d. Phototransistor

Last Answer : a. PMT

Optical Fiber What ?

Last Answer : Optical Fiber Holo - glass Or Of plastic Too much Narrow , long Flexible But Solid Fiber Or Fiber. One Place From Other In place Electric Signal Exchange Of payment For Optical Fiber Use To do Is.

EMDis best describe bywhich statement? a. 70percentofthe corediameter and70%ofthefiberNAshouldbe filled with light b.70 percent of the fiber diameter and 70% of the cone of acceptance should be filled with light c.70 percent of input light should be measured at the output d.70 percent of the unwanted wavelengths should be attenuated by the fiber

Description : EMDis best describe bywhich statement? a. 70percentofthe corediameter and70%ofthefiberNAshouldbe filled with light b.70 percent of the fiber diameter and 70% of the cone of acceptance should be filled with ... the output d.70 percent of the unwanted wavelengths should be attenuated by the fiber

Last Answer : a. 70percentofthe corediameter and70%ofthefiberNAshouldbe filled with light

The termssinglemode andmultimode are bestdescribes as a. the number of fibers placed into a fiber-optic cable b. the number of voice channels each fiber can support c.thenumber ofwavelengths eachfiber cansupport d. the index number

Description : The termssinglemode andmultimode are bestdescribes as a. the number of fibers placed into a fiber-optic cable b. the number of voice channels each fiber can support c.thenumber ofwavelengths eachfiber cansupport d. the index number

Last Answer : c.thenumber ofwavelengths eachfiber cansupport

The reflective index numberis a. anumberwhichcomparesthe transparencyof amaterialwiththatof air b. a number assigned by the manufacturer to the fiber in question c. a number which determines the core diameter d. a term for describing core elasticity

Description : The reflective index numberis a. anumberwhichcomparesthe transparencyof amaterialwiththatof air b. a number assigned by the manufacturer to the fiber in question c. a number which determines the core diameter d. a term for describing core elasticity

Last Answer : a. anumberwhichcomparesthe transparencyof amaterialwiththatof air

The claddingwhichsurroundsthe fiber core a. is used to reduce optical interference b. is used to protect the fiber c. acts to help guide the light in the core d. ensures that the refractive index remains constant

Description : The claddingwhichsurroundsthe fiber core a. is used to reduce optical interference b. is used to protect the fiber c. acts to help guide the light in the core d. ensures that the refractive index remains constant

Last Answer : c. acts to help guide the light in the core

Asingle fiber can handle asmanyvoice channel as a. a pair of copper conductors b. a1500-pair cable c. a 500-pair cable d. a 1000-pair cable

Description : Asingle fiber can handle asmanyvoice channel as a. a pair of copper conductors b. a1500-pair cable c. a 500-pair cable d. a 1000-pair cable

Last Answer : b. a1500-pair cable

In fiber-to-fiber connections, Fresnel reflection is one source of coupling losses. Light is reflected back into the source fiber and is lost. What causes Fresnel reflection?

Description : In fiber-to-fiber connections, Fresnel reflection is one source of coupling losses. Light is reflected back into the source fiber and is lost. What causes Fresnel reflection?

Last Answer : A step change in refractive index that occurs at fiber joints, caused by fiber separation.

How are source-to-fiber coupling and microbending and macrobending losses affected by changes in core diameter and D?

Description : How are source-to-fiber coupling and microbending and macrobending losses affected by changes in core diameter and D?

Last Answer : Coupling efficiency increases with both core diameter and D, while bending losses increase directly with core diameter and inversely with D.

How can a solar array power source be bypassed when the batteries run low?

Description : How can a solar array power source be bypassed when the batteries run low?

Last Answer : Ah got it. If anyone else is interested, you need an “automatic transfer switch” – or get a manual one for that mad scientist charm.

Three equal resistors connected in series with a source of e m f together dissipate 10 W of power each. What will be the power dissipated if the same resistors are connected in parallel across the same source of e m f? a. 40 W b. 90W c. 100W d. 120W

Description : Three equal resistors connected in series with a source of e m f together dissipate 10 W of power each. What will be the power dissipated if the same resistors are connected in parallel across the same source of e m f? a. 40 W b. 90W c. 100W d. 120W

Last Answer : b. 90W

What is the insertion loss of connector-type splices for a single mode fiber optics? a. 0.51dB b. 0.31dB c. 0.49dB d. 0.38dB

Description : What is the insertion loss of connector-type splices for a single mode fiber optics? a. 0.51dB b. 0.31dB c. 0.49dB d. 0.38dB

Last Answer : d. 0.38dB

What is the insertion loss of connector type splices for a single mode optical fiber? A. 0.51 dB B. 0.49 dB C. 0.31 dB D. 0.38 db

Description : What is the insertion loss of connector type splices for a single mode optical fiber? A. 0.51 dB B. 0.49 dB C. 0.31 dB D. 0.38 db

Last Answer : D. 0.38 db

Insertion loss of connector-type splices for a single-mode fiber cable. A. 0.2 dB B. 0.3 dB C. 0.09 dB D. 0.38 dB

Description : Insertion loss of connector-type splices for a single-mode fiber cable. A. 0.2 dB B. 0.3 dB C. 0.09 dB D. 0.38 dB

Last Answer : D. 0.38 dB

Which type of fiber optic connector (butt-jointed or expanded beam) brings the prepared ends of two optical fibers into close contact?

Description : Which type of fiber optic connector (butt-jointed or expanded beam) brings the prepared ends of two optical fibers into close contact?

Last Answer : Butt-jointed connectors.

What connection properties result in fiber optic connector coupling loss?

Description : What connection properties result in fiber optic connector coupling loss?

Last Answer : Poor fiber alignment and end preparation, fiber mismatches, and Fresnel reflection.

What is the insertion loss of connector-type splices for a single mode fiber optics? ∙ a. 0.51 dB ∙ b. 0.31 dB ∙ c. 0.49 dB ∙ d. 0.38 dB

Description : What is the insertion loss of connector-type splices for a single mode fiber optics? ∙ a. 0.51 dB ∙ b. 0.31 dB ∙ c. 0.49 dB ∙ d. 0.38 dB

Last Answer : d. 0.38 dB

Which of the following is a type of fiber connector: a. ST b. SC c. SMA d. all of the above

Description : Which of the following is a type of fiber connector: a. ST b. SC c. SMA d. all of the above

Last Answer : d. all of the above

The loss in single-mode fiber-optic cable due to a connector is about: a. 0.02 dB b. 0.2 dB c. 1 dB d. 3 dB

Description : The loss in single-mode fiber-optic cable due to a connector is about: a. 0.02 dB b. 0.2 dB c. 1 dB d. 3 dB

Last Answer : b. 0.2 dB

Which connector should you use to connect the (a) power source and (b) load to the fuseholder shown in figure 2-12(A)?

Description : Which connector should you use to connect the (a) power source and (b) load to the fuseholder shown in figure 2-12(A)?

Last Answer : a. Center connector b. Outside connector