List five precautions to take when installing fiber optic systems on board naval ships.

List five precautions to take when installing fiber optic  systems on board naval ships.
by

1 Answer

Answer :

a. Never bend an optical fiber or cable at a radius of  curvature less than the minimum bend radius.  
 b. Never pull fiber optic cables tight or fasten them over or  through sharp corners or cutting edges.  
 c. Always clean fiber optic connectors before mating.   d. Do not kink or crush fiber optic cable during installation  of the hardware.  
 e. Allow only trained, authorized personnel to install or  repair fiber optic systems.
by

Related questions

List the two principal optical detectors used in fiber optic systems.

Description : List the two principal optical detectors used in fiber optic systems.

Last Answer : The semiconductor positive-intrinsic-negative (PIN) photodiode and avalanche photodiode (APD).

List five common fiber optic transmitter packages.

Description : List five common fiber optic transmitter packages.

Last Answer : TO can, DIP, butterfly lead microcircuits, circuit cards, and stand-alone optical fiber converters.

Which types of LEDs are the preferred optical sources for short-distance, low-data-rate fiber optic systems?

Description : Which types of LEDs are the preferred optical sources for short-distance, low-data-rate fiber optic systems?

Last Answer : SLEDs and ELEDs.

Why is detector saturation not generally a problem in fiber optic communications systems?

Description : Why is detector saturation not generally a problem in fiber optic communications systems?

Last Answer : Because fiber optic communications systems operate at low optical power levels.

What type of modulation do most analog fiber optic communications systems use?

Description : What type of modulation do most analog fiber optic communications systems use?

Last Answer : Intensity modulation.

In fiber optic systems, designers consider what trade-offs?

Description : In fiber optic systems, designers consider what trade-offs?

Last Answer : Trade-offs in fiber properties, types of connections, optical sources, and detector types in military and subscriber-loop applications.

List the types of fiber optic components considered part of a fiber optic cable plant.

Description : List the types of fiber optic components considered part of a fiber optic cable plant.

Last Answer : Optical fiber cables, connectors, splices, mounting panels, jumper cables, and other passive components.

List four system topologies that can be constructed using point-to-point fiber optic links.

Description : List four system topologies that can be constructed using point-to-point fiber optic links.

Last Answer : Linear bus, ring, star, and tree topologies.

List the three parts of a fiber optic data link

Description : List the three parts of a fiber optic data link

Last Answer : Transmitter, optical fiber, and receiver.

What type of interface electronics is used in many naval electronic warfare systems?

Description : What type of interface electronics is used in many naval electronic warfare systems?

Last Answer : NTDS interface.

Who chooses the names for naval ships?

Description : Who chooses the names for naval ships?

Last Answer : It depends on the country, here are the US Navy standards.

What made naval destroyer ships so hard for a submarine to sink in World War 2?

Description : What made naval destroyer ships so hard for a submarine to sink in World War 2?

Last Answer : Naval destroyers were a menace to submarines during WW 2 anddifficult ships to sink. The speed of a destroyer and its abilityto maneuver quickly in open water made them difficult targets forsubmarines ... sink any submarine. The use of sonar by destroyers alsoallowed them to track enemy submarines.

What is the difference between passive and active fiber optic couplers?

Description : What is the difference between passive and active fiber optic couplers?

Last Answer : Passive couplers redistribute optical signals without optical-to electrical conversion.

The Navy classifies fiber optic connectors in what two ways?

Description : The Navy classifies fiber optic connectors in what two ways?

Last Answer : Light-duty and heavy-duty connectors.

Which type of fiber optic connector (butt-jointed or expanded beam) brings the prepared ends of two optical fibers into close contact?

Description : Which type of fiber optic connector (butt-jointed or expanded beam) brings the prepared ends of two optical fibers into close contact?

Last Answer : Butt-jointed connectors.

Fiber optic connectors can reduce system performance by increasing what two types of noise?

Description : Fiber optic connectors can reduce system performance by increasing what two types of noise?

Last Answer : Modal and reflection.

What connection properties result in fiber optic connector coupling loss?

Description : What connection properties result in fiber optic connector coupling loss?

Last Answer : Poor fiber alignment and end preparation, fiber mismatches, and Fresnel reflection.

Define a fiber optic splice.

Description : Define a fiber optic splice.

Last Answer : A permanent fiber joint whose purpose is to establish an optical connection between two individual optical fibers.

Which fiber optic component (splice, connector, or coupler) makes a permanent connection in a distributed system?

Description : Which fiber optic component (splice, connector, or coupler) makes a permanent connection in a distributed system?

Last Answer : Splice.

What are the two types of output interfaces for fiber optic transmitters?

Description : What are the two types of output interfaces for fiber optic transmitters?

Last Answer : Optical connectors and optical fiber pigtails.

Which part of a fiber optic transmitter converts the processed electrical signal to an optical signal?

Description : Which part of a fiber optic transmitter converts the processed electrical signal to an optical signal?

Last Answer : The optical source.

What are the three parts of a fiber optic transmitter?

Description : What are the three parts of a fiber optic transmitter?

Last Answer : Interface circuit, source drive circuit, and an optical source.

What are the two basic types of preamplifiers used in fiber optic receivers?

Description : What are the two basic types of preamplifiers used in fiber optic receivers?

Last Answer : The high-impedance amplifier and the transimpedance amplifier.

What is a fiber optic receiver?

Description : What is a fiber optic receiver?

Last Answer : An electro-optic device that accepts optical signals from an optical fiber and converts them into electrical signals

Why is it generally only necessary to refer to point-to-point data links when discussing the process of fiber optic system design?

Description : Why is it generally only necessary to refer to point-to-point data links when discussing the process of fiber optic system design?

Last Answer : Because fiber optic systems that incorporate complex architectures can be simplified into a collection of point-to-point data links before beginning the design process.

What is the main disadvantage of using fiber-optic cables?

Description : What is the main disadvantage of using fiber-optic cables?

Last Answer : High attenuation.

What effect does noise have on the fiber optic signal?

Description : What effect does noise have on the fiber optic signal?

Last Answer : Noise obscures or reduces the quality of the signal.

Describe the basic functions of a fiber optic data link

Description : Describe the basic functions of a fiber optic data link

Last Answer : The basic functions of a fiber optic data link are to convert an electrical input signal to an optical signal, send the optical signal over an optical fiber, and convert the optical signal back to an electrical signal.

ECE Board Exam March 1996 It is a spacecraft placed in orbit around the earth carrying onboard microwave receiver and transmitting equipments. A. Fiber optic equipment B. Communications satellite C. Wireless radio system D. Coaxial cable syste

Description : ECE Board Exam March 1996 It is a spacecraft placed in orbit around the earth carrying onboard microwave receiver and transmitting equipments. A. Fiber optic equipment B. Communications satellite C. Wireless radio system D. Coaxial cable syste

Last Answer : B. Communications satellite

List seven advantages of fiber optics over electrical systems.

Description : List seven advantages of fiber optics over electrical systems.

Last Answer : Advantages of fiber optics are improved system performance, immunity to electrical noise, signal security, electrical isolation, reduced size and w

Which of the following is not a common application of fiber-optic cable? a. Computer networks b. Long-distance telephone systems c. Closed circuit TV d. Consumer TV

Description : Which of the following is not a common application of fiber-optic cable? a. Computer networks b. Long-distance telephone systems c. Closed circuit TV d. Consumer TV

Last Answer : d. Consumer TV

Which of the following is not a common application of fiber-optic cable? ∙ a. Computer networks ∙ b. Long-distance telephone systems ∙ c. Closed circuit TV ∙ d. Consumer TV

Description : Which of the following is not a common application of fiber-optic cable? ∙ a. Computer networks ∙ b. Long-distance telephone systems ∙ c. Closed circuit TV ∙ d. Consumer TV

Last Answer : d. Consumer TV

List the safety precautions to be observed when replacing a fuse.

Description : List the safety precautions to be observed when replacing a fuse.

Last Answer : Be sure the power is off in the circuit and the circuit is discharged before replacing a fuse. Use an identical replacement fuse if possible. Remove any corrosion from the fuseholders before replacing the fuses.

List the safety precautions to be observed when checking fuses.

Description : List the safety precautions to be observed when checking fuses.

Last Answer : Turn the power off and discharge the circuit before you remove fuses. Use a fuse puller (an insulated tool) when you remove fuses d. Not acceptable-lower voltage rating e. Direct replacement

List the 11 safety precautions for multimeters

Description : List the 11 safety precautions for multimeters

Last Answer : a. Deenergize and discharge the circuit completely before connecting or disconnecting a multimeter. b. Never apply power to the circuit while measuring resistance with a multimeter. c. ... a multimeter. k. Observe the general safety precautions for electrical and electronic devices.

List the four safety precautions observed when using a megger.

Description : List the four safety precautions observed when using a megger.

Last Answer : a. Use meggers for high-resistance measurement only. b. Never touch the test leads when the handle is being cranked. c. Deenergize and discharge the circuit completely before connecting a megger. d. Disconnect the item being checked from other circuitry, if possible, before using a megger

List the four safety precautions observed when using ohmmeters.

Description : List the four safety precautions observed when using ohmmeters.

Last Answer : a. Deenergize and discharge the circuit before connecting an ohmmeter. b. Do not apply power to a circuit while measuring resistance. c. Switch ohmmeters to the OFF position, ... d. Adjust the ohmmeter after changing resistance range and before measuring reading indicates the resistance.

List the six safety precautions for the use of voltmeters.

Description : List the six safety precautions for the use of voltmeters.

Last Answer : a. Always connect a voltmeter in parallel. b. Always start with the highest range. c. Deenergize and discharge the circuit before connecting or disconnecting the voltmeter. d. ... to measure ac voltage. f. Observe the general safety precautions of electric and electronic devices.

List the six safety precautions for the use of ammeters

Description : List the six safety precautions for the use of ammeters

Last Answer : a. Always connect a voltmeter in parallel. b. Always start with the highest range. c. Deenergize and discharge the circuit before connecting or disconnecting the voltmeter. d. ... to measure ac voltage. f. Observe the general safety precautions of electric and electronic devices.

The naval communications system is made up of what two groups of communications?

Description : The naval communications system is made up of what two groups of communications?

Last Answer : Strategic and tactical.

What precautions should you take when tying bundles containing coaxial cables?

Description : What precautions should you take when tying bundles containing coaxial cables?

Last Answer : Do not tie too tightly and use the proper type of tape.

Why can multimode graded-index fiber 1300-nm systems using LEDs operate over longer distances and at higher bandwidths than 850-nm systems?

Description : Why can multimode graded-index fiber 1300-nm systems using LEDs operate over longer distances and at higher bandwidths than 850-nm systems?

Last Answer : Longer distances and higher bandwidths are possible because fiber material losses and dispersion are significantly reduced at the 1300-nm region.

Modal dispersion affects the bandwidth of multimode systems. It is essential to adjust what three fiber properties to maximize system bandwidth?

Description : Modal dispersion affects the bandwidth of multimode systems. It is essential to adjust what three fiber properties to maximize system bandwidth?

Last Answer : Core diameter, NA, and index profile properties.

What precautions should be exercised when using mercury-vapor thyratrons?

Description : What precautions should be exercised when using mercury-vapor thyratrons?

Last Answer : . The filament’s voltage should be applied to the tube at least 30 seconds before attempting to operate the tube.

What precautions must be taken when sweeping a transmitting antenna?

Description : What precautions must be taken when sweeping a transmitting antenna?

Last Answer : You must ensure that power induced from any adjacent transmitting antennas does not damage your test equipment.

When should safety precautions pertaining to batteries be observed?

Description : When should safety precautions pertaining to batteries be observed?

Last Answer : .At all times.

Should aluminum wire be cleaned prior to installing an aluminum terminal lug or splice?

Description : Should aluminum wire be cleaned prior to installing an aluminum terminal lug or splice?

Last Answer : No, it is done automatically by the petroleum abrasive compound that comes in the terminal or splices.

List six types of fiber mismatches.

Description : List six types of fiber mismatches.

Last Answer : Core diameter mismatch, cladding diameter mismatch, core ellipticity, core and cladding concentricity differences, NA mismatch, and refractive index profile differences.

List the three basic errors that occur during fiber alignment.

Description : List the three basic errors that occur during fiber alignment.

Last Answer : Fiber separation (longitudinal misalignment), lateral misalignment, and angular misalignment.

List the fiber geometrical measurements performed in the laboratory.

Description : List the fiber geometrical measurements performed in the laboratory.

Last Answer : Cladding diameter, core diameter, numerical aperture, and mode field diameter.