Description : If the impedance of the choke is increased, will the ripple amplitude increase or decrease?
Last Answer : Decrease.
Description : Capacitors are used on the output of the power supply in today's consoles to _____________. A. filter out 'ripple' B. prevent overloads C. act as a permanent load D. decrease the average value of the output voltage
Last Answer : Answer: A
Description : In an LC choke-input filter, what prevents the rapid charging of the capacitor?
Last Answer : The CEMF of the inductor
Last Answer : Counter electro-motive force of the inductor.
Description : Does a filter circuit increase or decrease the average output voltage?
Last Answer : A filter circuit increases the average output voltage
Last Answer : Increase.
Description : When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease (which one) in the resistance of the regulating device.
Last Answer : An increase.
Description : When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease in the resistance of the regulating device.
Description : If the electricity represented by the wave form in 'B' were applied to the left side of the illustrated circuit, the output on the right side would be ____________. EL-0064 A. direct current with the ... lower lead D. clipped to a value equal to the square root of 3 times the input voltage value
Last Answer : Answer: C
Description : What is the value usually chosen for a filter choke?
Last Answer : 1 to 20 henries.
Description : The purpose of choke in a fluorescent lamp is – (1) to increase the current flow (2) to decrease the current flow (3) to decrease the resistance (4) to decrease the voltage momentarily
Last Answer : (2) to decrease the current flow Explanation: The choke primarily serves to limit current flow to the correct level for the tube. It also can be used during startup to provide an inductive 'kick' forming a momentary highervoltage pulse to start the lamp.
Description : The purpose of choke in a fluorescent lamp is : (1) to increase the current flow (2) to decrease the current flow (3) to decrease the resistance (4) ro decrease the voltage momentarily
Last Answer : to decrease the current flow
Description : If If the input signals are 180 degrees out of phase with each other and a combined output is taken between the two output terminals, what will the amplitude of the combined output signal be?
Last Answer : 200 millivolts.
Description : If the input signals are 180 degrees out of phase with each other, what will be the peak-to-peak amplitude of the output signals?
Last Answer : Each output signal will be 100 millivolts.
Description : If the input signals are in phase, what will be the peak-to peak amplitude of the output signals?
Last Answer : 0 volts (the input signals will "cancel out").
Description : If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?
Last Answer : 200 millivolts. A-18. a. Differential amplifier
Description : If the two input signals to a difference amplifier are equal in amplitude but neither in phase nor 180 degrees out of phase, what will the output signal be?
Last Answer : . A different shape than the input signals but larger in amplitude.
Description : If the two input signals to a difference amplifier are equal in amplitude and 180 degrees out of phase, what will the output signal be?
Last Answer : Equal in shape and frequency to each input signal and larger in amplitude by two times than
Description : . If the two input signals of a difference amplifier are in phase and equal in amplitude, what will the output signal be?
Last Answer : No output (the signals will "cancel out").
Description : If the filter capacitance is increased, the ripple will (a) remain same (b) increase (c) decrease (d) be zero
Last Answer : C
Description : What is the ripple frequency of a full-wave rectifier with an input frequency of 60 Hz?
Last Answer : 120 hertz.
Description : What is the Ripple frequency of a half-wave rectifier if the input frequency is 60 Hz?
Last Answer : 60 hertz.
Description : What effect does inductance have (a) on steady direct current and (b) on direct current while it is changing in amplitude?
Last Answer : a) No effect. (b) Inductance opposes any change in the amplitude of current.
Description : The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an ... drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor
Last Answer : Answer: D
Description : Does low ripple voltage indicate good or bad filtering?
Last Answer : Good.
Description : The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc voltage with resistive load and without filter will be • 12.1 volt • 1.21 volt • 0.482 volt • 4.82 volt
Last Answer : The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc voltage with resistive load and without filter will be 12.1 volt
Description : What would be the output of a negative clamper with a bias potential of −5 volts and an input voltage swing from +50 to −50 volts?
Last Answer : -5 volts.
Description : When the input and output wipers of a balanced potentiometer are in the same angular position, what is the value of the error voltage?
Last Answer : Zero.
Description : What characteristic is determined by the time required for a voltage wave to travel from the input end of an artificial transmission line to the output end and back again?
Last Answer : Pulse width
Last Answer : Pulse width.
Description : Production rate __________ with increased fineness, with a given energy input to the size reduction machine. (A) Decreases (B) Increases (C) Remains unchanged (D) May increase or decrease; depends on the machine
Last Answer : (A) Decreases
Description : A, when there is an increase in the input voltage, the forward bias of Q1 increases/decreases (which one).
Last Answer : Increases.
Description : Explain operation of series inductor filter and find out its ripple factor.
Last Answer : Circuit diagram of series inductor filter : Operation of Series Inductor Filter : A high value of inductor is connected in series with load. Then the combination is connected across the rectifier. ... Hence increase in current reduces ripple factor. Ripple Factor:- RF = R / 3√2 ω L
Description : The ripple factor in an LC filter. (A) Increases with the load current (B) Increases with the load resistance (C) Remains constant with the load current (D) Has the lowest value
Last Answer : The ripple factor in an LC filter. Has the lowest value
Description : The term responsivity as it applies to a light detector is best described as ∙ A. the time required for the signal to go from 10 to 90 percent of maximum amplitude ∙ B. the ratio of the diode ... . the ratio of the input power to output power ∙ D. the ratio of output current to input current
Last Answer : the ratio of the diode output current to the input optical power
Description : The termresponsivityasit appliesto a light detectorisbest described as a. the time required for the signal to go from 10 to 90 percent of maximum amplitude b.the ratio ofthediode output currentto ... of output current to output power d. the ratio of output current to input current
Last Answer : b.the ratio ofthediode output currentto opticalinputpower
Description : What is the amplitude and voltage induced into the rotor when the CX is turned 90º while the CT remains on electrical zero?
Last Answer : The voltage is maximum and in phase with the ac excitation voltage to the CX.
Description : . What three factors determine the amplitude of the voltage induced into a stator winding?
Last Answer : The amplitude of the primary voltage, the turns ratio, and the angular displacement between the rotor and the stator winding.
Description : Is better filtering achieved at a high frequency or at a low frequency at the input of the filter?
Last Answer : High
Description : What is the range of values usually chosen for a choke?
Last Answer : To determine that all data can be processed correctly and that the output is correct.
Description : In successive-approximation A/D converter, offset voltage equal to 1/2 LSB is added to the D/A converter's output. This is done to (A) Improve the speed of operation. (B) Reduce the maximum ... Increase the number of bits at the output. (D) Increase the range of input voltage that can be converted
Last Answer : (B) Reduce the maximum quantization error.
Description : Assuming a standard 60 Hz. input to the circuit shown in the illustration, the ripple frequency would be ____________. EL-0085 A. 30 Hz B. 60 Hz C. 90 Hz D. 120 Hz
Description : An eight stage ripple counter uses a flip-flop with propagation delay of 75 nanoseconds. The pulse width of the strobe is 50ns. The frequency of the input signal which can be used for proper operation of the counter is approximately (A) 1 MHz. (B) 500 MHz. (C) 2 MHz. (D) 4 MHz.
Last Answer : Maximum time taken for all flip-flops to stabilize is 75ns x 8 + 50 = 650ns. Frequency of operation must be less than 1/650ns = 1.5 MHz.
Description : A 3 -stage ripple counter has Flip Flop with propagation delay of 25 nsec and pulse width of strobe input 10 nsec. Then the maximum operating frequency at which counter operates reliably is
Last Answer : A 3 -stage ripple counter has Flip Flop with propagation delay of 25 nsec and pulse width of strobe input 10 nsec. Then the maximum operating frequency at which counter operates reliably is 12.67 MHz
Description : The input frequency is 50 Hz. The ripple frequency in a 12 phase full wave rectifier is (A) 1200 Hz (B) 600 Hz (C) 100 Hz (D) 50 Hz
Last Answer : The input frequency is 50 Hz. The ripple frequency in a 12 phase full wave rectifier is 1200 Hz
Description : Is a full-wave rectifier output easier to filter than that of a half-wave rectifier?
Last Answer : Yes.
Description : Transformers are used onboard ships with AC generators to _____________. A. change frequency B. increase power output to modulating frequency controllers C. decrease power output to modulating frequency ... D. permit higher voltage for electric motor operation and low voltage for lighting circuits