A loss of receiver sensitivity has the same effect on range performance as what other loss?

A loss of receiver sensitivity has the same effect on range  performance as what other loss?
by

1 Answer

Answer :

Transmitter power loss.
by

Related questions

When measuring receiver sensitivity, what quantities must you add to the dBm reading obtained on the signal generator or test set?

Description : When measuring receiver sensitivity, what quantities must you add to the dBm reading obtained on the signal generator or test set?

Last Answer : Attenuations of the directional coupler and the connecting cable.

You determine receiver sensitivity by measuring the power level of what signal?

Description : You determine receiver sensitivity by measuring the power level of what signal?

Last Answer : Minimum discernible signal (mds).

Which amplifier stage (the preamplifier or the postamplifier) is a dominant contributor of noise and significantly influences the sensitivity of the receiver?

Description : Which amplifier stage (the preamplifier or the postamplifier) is a dominant contributor of noise and significantly influences the sensitivity of the receiver?

Last Answer : The preamplifier.

What is the main factor that determines receiver sensitivity?

Description : What is the main factor that determines receiver sensitivity?

Last Answer : Noise

Which preamplifier design (high-impedance or transimpedance) provides improvements in bandwidth and greater dynamic range with some degradation in sensitivity from an increase in noise?

Description : Which preamplifier design (high-impedance or transimpedance) provides improvements in bandwidth and greater dynamic range with some degradation in sensitivity from an increase in noise?

Last Answer : Transimpedance.

List the key operational parameters used to define receiver performance.

Description : List the key operational parameters used to define receiver performance.

Last Answer : Receiver sensitivity, bandwidth, and dynamic range.

Define receiver dynamic range.

Description : Define receiver dynamic range.

Last Answer : The range of optical power levels over which the receiver operates within the specified values. It

What limits the sensitivity of a receiver? A. The power supply of the receiver B. The power output of a transmitter C. The noise floor of the receiver D. The distance between the transmitter and receiver

Description : What limits the sensitivity of a receiver? A. The power supply of the receiver B. The power output of a transmitter C. The noise floor of the receiver D. The distance between the transmitter and receiver

Last Answer : C. The noise floor of the receiver

ECE Board Exam March 1996 What is the purpose of the receiver’s squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent fluctuations in the AGC bias level C. To reduce the receiver’s sensitivity to all incoming signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Description : ECE Board Exam March 1996 What is the purpose of the receiver's squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent ... signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Last Answer : D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Define selectivity and sensitivity of AM Receiver.

Description : Define selectivity and sensitivity of AM Receiver. 

Last Answer : Selectivity:-It needs to accept signals of the wanted frequency and reject other unwanted frequencies. Sensitivity:-The sensitivity of a radio receiver is its ability to amplify weak signals. It is ... the receiver input terminals to give a standard output power, measured at the output terminals. 

Explain the following characteristics of AM radio receiver: (i) Sensitivity (ii) Selectivity.

Description : Explain the following characteristics of AM radio receiver: (i) Sensitivity (ii) Selectivity.

Last Answer : Sensitivity:- The ability to amplify the weak signals is called sensitivity. It is the function of overall receiver gain. Sensitivity of radio receiver is decided by the gain of the RF IF ... perfectly the receiver is able to select the desired carrier frequency and reject other frequencies. 

Deemphasis in the receiver in effect attenuates modulating signal components and noise in what frequency range? A. dc B. low C. intermediate D. high

Description : Deemphasis in the receiver in effect attenuates modulating signal components and noise in what frequency range? A. dc B. low C. intermediate D. high

Last Answer : D. high

What term is used to describe the reciprocal of deflection sensitivity of a scope?

Description : What term is used to describe the reciprocal of deflection sensitivity of a scope?

Last Answer : Deflection factor.

How is fiber sensitivity to bending losses reduced?

Description : How is fiber sensitivity to bending losses reduced?

Last Answer : Fiber sensitivity to bending losses can be reduced if the refractive index of the core is increased and/or if the overall diameter of the fiber increases.

What is voltmeter sensitivity?

Description : What is voltmeter sensitivity?

Last Answer : It is an indication of the resistance of the meter expressed in ohms per volt. The total resistance of the meter is the sensitivity multiplied by the full-scale voltage.

What is ammeter sensitivity?

Description : What is ammeter sensitivity?

Last Answer : The amount of current that will cause full-scale deflection.

What term is used to express the sensitivity of a voltmeter?

Description : What term is used to express the sensitivity of a voltmeter?

Last Answer : Ohms per volt

(True or False) The larger the current required to produce full-scale deflection of the meter coil, the better the sensitivity of the meter.

Description : (True or False) The larger the current required to produce full-scale deflection of the meter coil, the better the sensitivity of the meter.

Last Answer : False.

External shunts are sometimes used with ammeters to _______. A. increase meter sensitivity B. permit shunts with larger resistances to be utilized C. prevent damage to the meter movement from heat generated by the shunt D. enable the construction of a compact meter with a virtually unlimited range

Description : External shunts are sometimes used with ammeters to _______. A. increase meter sensitivity B. permit shunts with larger resistances to be utilized C. prevent damage to the meter movement from heat generated by the shunt D. enable the construction of a compact meter with a virtually unlimited range

Last Answer : Answer: C

The following are true about the contrast sensitivity: a. Pelli-Robson chart tests the contrast sensitivity b. is a measure of the ratio of brightness to darkness c. a contrast of 1 means that there is no contrast d. is highest at middle range frequencies

Description : The following are true about the contrast sensitivity: a. Pelli-Robson chart tests the contrast sensitivity b. is a measure of the ratio of brightness to darkness c. a contrast of 1 means that there is no contrast d. is highest at middle range frequencies

Last Answer : is highest at middle range frequencies

A dc voltmeter has a sensitivity of 1000 Ohm/V. When it measures half full scale in 100 V range, the current ...

Description : A dc voltmeter has a sensitivity of 1000 Ohm/V. When it measures half full scale in 100 V range, the current through the voltmeter is

Last Answer : A dc voltmeter has a sensitivity of 1000 Ohm/V. When it measures half full scale in 100 V range, the current through the voltmeter is 1 mA.

What is the disadvantage of using a double receiver instead of two individual receivers?

Description : What is the disadvantage of using a double receiver instead of two individual receivers?

Last Answer : If one of the receivers goes bad the entire unit must be replaced.

When is a synchro receiver (TR) properly zeroed?

Description : When is a synchro receiver (TR) properly zeroed?

Last Answer : A TR is zeroed when electrical zero voltages exist across its stator windings at the same time its rotor is on zero or on its mechanical reference position.

What is the most likely problem if the transmitter shaft reads 0º when the receiver shaft indicates 180º?

Description : What is the most likely problem if the transmitter shaft reads 0º when the receiver shaft indicates 180º?

Last Answer : The rotor leads on either the transmitter or the receiver are reversed.

What two receiver leads are reversed to reverse the rotor's direction of rotation?

Description : What two receiver leads are reversed to reverse the rotor's direction of rotation?

Last Answer : 1 and S3.

What is the relationship between the transmitter and receiver stator voltages when their rotors are in correspondence?

Description : What is the relationship between the transmitter and receiver stator voltages when their rotors are in correspondence?

Last Answer : The voltages are equal and oppose each other.

What is the physical difference between a synchro transmitter and a synchro receiver?

Description : What is the physical difference between a synchro transmitter and a synchro receiver?

Last Answer : A synchro receiver uses some form of damping to retard excessive oscillations or spinning.

Receiver bandwidth is defined as those frequencies spread between what two points of the receiver response curve?

Description : Receiver bandwidth is defined as those frequencies spread between what two points of the receiver response curve?

Last Answer : Half-power points.

Where should the transmitter spectrum be located with respect to the receiver response curve?

Description : Where should the transmitter spectrum be located with respect to the receiver response curve?

Last Answer : In the center.

A monopulse receiver has how many separate channels?

Description : A monopulse receiver has how many separate channels?

Last Answer : Three.

How does ftc affect receiver gain, if at all?

Description : How does ftc affect receiver gain, if at all?

Last Answer : FTC has no effect on receiver gain

Immediately after the transmitter fires, stc reduces the receiver gain to what level?

Description : Immediately after the transmitter fires, stc reduces the receiver gain to what level?

Last Answer : Zero.

Which receiver component converts the IF pulses to video pulses?

Description : Which receiver component converts the IF pulses to video pulses?

Last Answer : Detector.

What receiver circuit actually produces the IF frequency?

Description : What receiver circuit actually produces the IF frequency?

Last Answer : Mixer.

Which component of the receiver produces the signal that is mixed with the received signal to produce the IF signal?

Description : Which component of the receiver produces the signal that is mixed with the received signal to produce the IF signal?

Last Answer : Local oscillator.

What type of receiver is most often used in radar systems?

Description : What type of receiver is most often used in radar systems?

Last Answer : Superheterodyne.

What tube in a duplexer has the primary function of disconnecting the receiver?

Description : What tube in a duplexer has the primary function of disconnecting the receiver?

Last Answer : Tr tube.

what causes the initial and final pulses on the receiver output signal?

Description : what causes the initial and final pulses on the receiver output signal?

Last Answer : Leakage from the duplexer.

What is the result of an impedance mismatch between a receiver or transmitter and its transmission line or antenna?

Description : What is the result of an impedance mismatch between a receiver or transmitter and its transmission line or antenna?

Last Answer : High vswr, which equates to poor reception or a loss of power output.

. Which part of the receiver amplifies the electrical signal to a level suitable for further signal processing?

Description : . Which part of the receiver amplifies the electrical signal to a level suitable for further signal processing?

Last Answer : Amplifier.

What is a fiber optic receiver?

Description : What is a fiber optic receiver?

Last Answer : An electro-optic device that accepts optical signals from an optical fiber and converts them into electrical signals

List the main types of receiver noise.

Description : List the main types of receiver noise.

Last Answer : Thermal noise, dark current noise, and quantum noise

What is the function of a crystal filter in a receiver?

Description : What is the function of a crystal filter in a receiver?

Last Answer : It is used to achieve maximum selectivity.

What does a tone control circuit in a receiver do to the audio signal?

Description : What does a tone control circuit in a receiver do to the audio signal?

Last Answer : It controls the amount of bass and treble response.

What two components give a ssb receiver its advantages over an AM superheterodyne receiver?

Description : What two components give a ssb receiver its advantages over an AM superheterodyne receiver?

Last Answer : A special type of detector and a carrier reinsertion oscillator

What are the four basic receiver characteristics?

Description : What are the four basic receiver characteristics?

Last Answer : Sensitivity, noise, selectivity, and fidelity.

What four basic functions must a receiver perform?

Description : What four basic functions must a receiver perform?

Last Answer : Reception, selection, detection, and reproduction.

What is the purpose of agc/avc in a receiver?

Description : What is the purpose of agc/avc in a receiver?

Last Answer : To limit unwanted variations in the output.

What type of tuning does the receiver use?

Description : What type of tuning does the receiver use?

Last Answer : Digital

What function does a receiver transfer switchboard perform?

Description : What function does a receiver transfer switchboard perform?

Last Answer : Transfers receiver audio outputs to remote control stations.