What is the most likely problem if the transmitter shaft reads 0º when the receiver shaft indicates 180º?

What is the most likely problem if the transmitter shaft  reads 0º when the receiver shaft indicates 180º?
by

1 Answer

Answer :

The rotor leads on either the transmitter or the receiver are  reversed.
by

Related questions

What is the relationship between the transmitter and receiver stator voltages when their rotors are in correspondence?

Description : What is the relationship between the transmitter and receiver stator voltages when their rotors are in correspondence?

Last Answer : The voltages are equal and oppose each other.

What is the physical difference between a synchro transmitter and a synchro receiver?

Description : What is the physical difference between a synchro transmitter and a synchro receiver?

Last Answer : A synchro receiver uses some form of damping to retard excessive oscillations or spinning.

Where should the transmitter spectrum be located with respect to the receiver response curve?

Description : Where should the transmitter spectrum be located with respect to the receiver response curve?

Last Answer : In the center.

Immediately after the transmitter fires, stc reduces the receiver gain to what level?

Description : Immediately after the transmitter fires, stc reduces the receiver gain to what level?

Last Answer : Zero.

What is the result of an impedance mismatch between a receiver or transmitter and its transmission line or antenna?

Description : What is the result of an impedance mismatch between a receiver or transmitter and its transmission line or antenna?

Last Answer : High vswr, which equates to poor reception or a loss of power output.

Indian Standard Time (IST) is determined according to the local time of which one of the following longitudes? (a) 0º Longitude (b) 68º E Longitude (c) c) E Longitude (d) d) E Longitude

Description : Indian Standard Time (IST) is determined according to the local time of which one of the following longitudes? (a) 0º Longitude (b) 68º E Longitude (c) c) E Longitude (d) d) E Longitude

Last Answer : Ans: (d)

What is the International Date Line? (a) An imaginary line connecting places of the same altitude (b) It is 180º Meridian from Greenwich (c) Region within 5º of the Equator (d) None of these

Description : What is the International Date Line? (a) An imaginary line connecting places of the same altitude (b) It is 180º Meridian from Greenwich (c) Region within 5º of the Equator (d) None of these

Last Answer : Ans: (b)

ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Description : ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Last Answer : B. 2.656 watts

ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Description : ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Last Answer : A. PAM

A basic touch screen has three main components. It includes touch sensor, controller and ________ A. transmitter B. receiver C. software driver D. None of the Above

Description : A basic touch screen has three main components. It includes touch sensor, controller and ________ A. transmitter B. receiver C. software driver D. None of the Above

Last Answer : C. software driver

If coils 'R1-R2-R3' at the receiver of figure 'B' shown in the illustration turned opposite of those in the transmitter by design, what corrective action should be taken? EL-0092 A. Reverse the 60 Hz supply connections to 'S1' and 'S2'. B. No action is needed. C. Interchange leads 'R1' and 'R3'. D. Interchange leads 'R2' and 'R3'.

Description : If coils 'R1-R2-R3' at the receiver of figure 'B' shown in the illustration turned opposite of those in the transmitter by design, what corrective action should be taken? EL-0092 A. Reverse the 60 Hz supply ... is needed. C. Interchange leads 'R1' and 'R3'. D. Interchange leads 'R2' and 'R3'.

Last Answer : Answer: B

If coils 'R1-R2-R3' at the receiver of figure 'B' shown in the illustration were in 180 degree error with those of the transmitter, what corrective action should be taken? EL-0092 A. Reverse the 60 Hz connections to 'S1' and 'S2'. B. No action is needed as this is proper operation. C. Interchange leads 'R1' and 'R3'. D. Interchange leads 'R2' and 'R3'.

Description : If coils 'R1-R2-R3' at the receiver of figure 'B' shown in the illustration were in 180 degree error with those of the transmitter, what corrective action should be taken? EL-0092 A. Reverse the 60 Hz ... is proper operation. C. Interchange leads 'R1' and 'R3'. D. Interchange leads 'R2' and 'R3'.

Last Answer : Answer: A

If coil 'R1-R2' at the receiver of figure 'A' shown in the illustration were in 180 degree error with respect to that of the transmitter, what corrective action should be taken? EL-0092 A. No action is necessary as this is proper operation. B. Reverse the 60 Hz supply connections at 'R1' and 'R2'. C. Interchange connections 'S1' and 'S2'. D. Interchange connections 'S1' and 'S3'.

Description : If coil 'R1-R2' at the receiver of figure 'A' shown in the illustration were in 180 degree error with respect to that of the transmitter, what corrective action should be taken? EL-0092 A. No action is ... and 'R2'. C. Interchange connections 'S1' and 'S2'. D. Interchange connections 'S1' and 'S3'.

Last Answer : Answer: B

If coils 'R1-R2-R3' at the receiver of figure 'B' shown in the illustration turned opposite of those in the transmitter, what corrective action should be taken to have both turn in the same direction? EL-0092 A. Reverse the 60 Hz supply connections to 'S1' and 'S2'. B. No action is needed. C. Interchange leads 'R1' and 'R3'. D. Interchange leads 'R2' and 'R3'.

Description : If coils 'R1-R2-R3' at the receiver of figure 'B' shown in the illustration turned opposite of those in the transmitter, what corrective action should be taken to have both turn in the same direction? EL-0092 A ... is needed. C. Interchange leads 'R1' and 'R3'. D. Interchange leads 'R2' and 'R3'.

Last Answer : Answer: C

If coil 'R1-R2' at the receiver of figure 'A' shown in the illustration turned opposite of that in the transmitter, what corrective action should be taken? EL-0092 A. No action is necessary as this is normal operation. B. Reverse 60 Hz supply connections to 'R1' and 'R2'. C. Interchange connections to 'S1' and 'S2'. D. Interchange connections to 'S1' and 'S3'.

Description : If coil 'R1-R2' at the receiver of figure 'A' shown in the illustration turned opposite of that in the transmitter, what corrective action should be taken? EL-0092 A. No action is necessary as this is ... . C. Interchange connections to 'S1' and 'S2'. D. Interchange connections to 'S1' and 'S3'.

Last Answer : Answer: D

If coil 'R1-R2' on the transmitter in figure 'A' shown in the illustration is turned 30 degrees clockwise, corresponding coil 'R1-R2' on the receiver should ____________. EL-0092 A. make coils 'S1-S2-S3' turn faster because of induced currents B. ring at the receiving station until the turning stops C. receive a higher voltage depending on the turns ratio D. align itself to the same position if free to move

Description : If coil 'R1-R2' on the transmitter in figure 'A' shown in the illustration is turned 30 degrees clockwise, corresponding coil 'R1-R2' on the receiver should ____________. EL-0092 A. make coils 'S1 ... a higher voltage depending on the turns ratio D. align itself to the same position if free to move

Last Answer : Answer: D

The total propagation delay time from transmission to reception of signals from a ground transmitter to ground receiver with angle of elevation at 10 degrees respectively is A. 273 ms B. 239 ms C. 275 ms D. 260 ms

Description : The total propagation delay time from transmission to reception of signals from a ground transmitter to ground receiver with angle of elevation at 10 degrees respectively is A. 273 ms B. 239 ms C. 275 ms D. 260 ms

Last Answer : A. 273 ms

What is the delay time for satellite transmissions from earth transmitter to earth receiver? A. 0.5 s B. 1s C. 5 ms D. 0.25 s

Description : What is the delay time for satellite transmissions from earth transmitter to earth receiver? A. 0.5 s B. 1s C. 5 ms D. 0.25 s

Last Answer : A. 0.5 s

What is the delay time for satellite transmission from earth transmitter to earth receiver? A. 0.5 s B. 1.0 s C. 5 ms D. 0.25 ms

Description : What is the delay time for satellite transmission from earth transmitter to earth receiver? A. 0.5 s B. 1.0 s C. 5 ms D. 0.25 ms

Last Answer : A. 0.5 s

What limits the sensitivity of a receiver? A. The power supply of the receiver B. The power output of a transmitter C. The noise floor of the receiver D. The distance between the transmitter and receiver

Description : What limits the sensitivity of a receiver? A. The power supply of the receiver B. The power output of a transmitter C. The noise floor of the receiver D. The distance between the transmitter and receiver

Last Answer : C. The noise floor of the receiver

Which of the following is not one of the natural ways a radio wave may travel from transmitter to receiver? A. Ground wave B. Micro wave C. Sky wave D. Space wave

Description : Which of the following is not one of the natural ways a radio wave may travel from transmitter to receiver? A. Ground wave B. Micro wave C. Sky wave D. Space wave

Last Answer : B. Micro wave

A satellite transmitter operates at 4GHz with an antenna gain of 4dBi. The receiver 40000 km away has an antenna gain of 50 dBi. If the transmitter has a power of 8 W, find (ignoring feedline losses and mismatch) the EIRP in dBW. A. 50 B. 69 C. 49 D. 30

Description : A satellite transmitter operates at 4GHz with an antenna gain of 4dBi. The receiver 40000 km away has an antenna gain of 50 dBi. If the transmitter has a power of 8 W, find (ignoring feedline losses and mismatch) the EIRP in dBW. A. 50 B. 69 C. 49 D. 30

Last Answer : C. 49

What is the uplink receiver frequency if the downlink transmitter is on channel 4 (3.84 Ghz)? A. 6.065 GHz B. 6.84 GHz C. 6.65 GHz D. 6.05 GHz

Description : What is the uplink receiver frequency if the downlink transmitter is on channel 4 (3.84 Ghz)? A. 6.065 GHz B. 6.84 GHz C. 6.65 GHz D. 6.05 GHz

Last Answer : A. 6.065 GHz

What is the path attenuation between transmitter and receiver at a frequency of 1.2 Ghz and a distance of 11,000 mi? A. 119 dB B. 115dB C. 179dB D. 174dB

Description : What is the path attenuation between transmitter and receiver at a frequency of 1.2 Ghz and a distance of 11,000 mi? A. 119 dB B. 115dB C. 179dB D. 174dB

Last Answer : C. 179dB

What is the device used in fiber optic communication which consist of a receiver transmitter use to clean up and amplify digital data moving in one direction and another in the opposite direction? A. Optic compressors B. Optic retarders C. Optic isolator D. Optic regenerators

Description : What is the device used in fiber optic communication which consist of a receiver transmitter use to clean up and amplify digital data moving in one direction and another in the opposite direction? A. Optic compressors B. Optic retarders C. Optic isolator D. Optic regenerators

Last Answer : D. Optic regenerators

Who is responsible in the correctness and accuracy of transmitted information content over a data communication? A. The channel B. The transmitter and receiver C. The modem D. The bridge

Description : Who is responsible in the correctness and accuracy of transmitted information content over a data communication? A. The channel B. The transmitter and receiver C. The modem D. The bridge

Last Answer : B. The transmitter and receiver

Main basic components of a data communication are composed of the following. A. Computer, modern and router B. Computer, bridge and gateway C. Transmitter, channel and receiver D. Transmitter, computer and modem

Description : Main basic components of a data communication are composed of the following. A. Computer, modern and router B. Computer, bridge and gateway C. Transmitter, channel and receiver D. Transmitter, computer and modem

Last Answer : C. Transmitter, channel and receiver

How can receiver desensitizing be reduced? A. Increase the receiver bandwidth B. Ensure good RF shielding between the transmitter and receiver C. Increase the transmitter audio gain D. Decrease the receiver squelch, gain.

Description : How can receiver desensitizing be reduced? A. Increase the receiver bandwidth B. Ensure good RF shielding between the transmitter and receiver C. Increase the transmitter audio gain D. Decrease the receiver squelch, gain.

Last Answer : D. Decrease the receiver squelch, gain.

Referred to as a ferrite device that can be used in lieu of a duplexer to isolate a microwave transmitter and receiver when both are connected to the same antenna. A. Isolator B. Circulator C. Coupler D. Diode.

Description : Referred to as a ferrite device that can be used in lieu of a duplexer to isolate a microwave transmitter and receiver when both are connected to the same antenna. A. Isolator B. Circulator C. Coupler D. Diode.

Last Answer : B. Circulator

______ is the first component of any MATV system to received broadcast signals. A. Receiver B. Antenna C. Filter D. Transmitter

Description : ______ is the first component of any MATV system to received broadcast signals. A. Receiver B. Antenna C. Filter D. Transmitter

Last Answer : B. Antenna

ECE Board Exam March 1996 The capture area of an antenna is directly proportional to the A. frequency of the received signal B. distance between transmitter and receiver C. gain of the antenna D. power density of the signal

Description : ECE Board Exam March 1996 The capture area of an antenna is directly proportional to the A. frequency of the received signal B. distance between transmitter and receiver C. gain of the antenna D. power density of the signal

Last Answer : C. gain of the antenna

The device that is used to convert energy from one form to another is called A : Emiter B : Transducer C : Transmitter D : Receiver

Description : The device that is used to convert energy from one form to another is called A : Emiter B : Transducer C : Transmitter D : Receiver

Last Answer : B : Transducer

The device that is used to convert energy from one form to another is called A : Emiter B : Transducer C : Transmitter D : Receiver

Description : The device that is used to convert energy from one form to another is called A : Emiter B : Transducer C : Transmitter D : Receiver

Last Answer : B : Transducer

The device that is used to convert energy from one form to another is called A : Emiter B : Transducer C : Transmitter D : Receiver

Description : The device that is used to convert energy from one form to another is called A : Emiter B : Transducer C : Transmitter D : Receiver

Last Answer : B : Transducer

The device that is used to convert energy from one form to another is called A : Emiter B : Transducer C : Transmitter D : Receiver

Description : The device that is used to convert energy from one form to another is called A : Emiter B : Transducer C : Transmitter D : Receiver

Last Answer : B : Transducer

The situation when both transmitter and receiver have to work in tandem is referred to as (A) parallel (B) serial (C) synchronous (D) asynchronous

Description : The situation when both transmitter and receiver have to work in tandem is referred to as (A) parallel (B) serial (C) synchronous (D) asynchronous

Last Answer : (C) synchronous

Calculate the total rise time for a fiber-optic system if the transmitter, receiver, and cable each have a rise time of 50 nanoseconds.

Description : Calculate the total rise time for a fiber-optic system if the transmitter, receiver, and cable each have a rise time of 50 nanoseconds.

Last Answer : 86.6 nanoseconds

The three major groups of the optical system are ∙ A. the components, the data rate and the response time ∙ B. the source, the link and the receiver ∙ C. the transmitter, the cable and the receiver ∙ D. the source, the link and the detector

Description : The three major groups of the optical system are ∙ A. the components, the data rate and the response time ∙ B. the source, the link and the receiver ∙ C. the transmitter, the cable and the receiver ∙ D. the source, the link and the detector

Last Answer : B. the source, the link and the receiver

Involves compression in the transmitter after the input sample has been converted to a linear PCM code and then expansion in the receiver prior to PCM coding:

Description : Involves compression in the transmitter after the input sample has been converted to a linear PCM code and then expansion in the receiver prior to PCM coding:

Last Answer : Digital companding

The threemajor groupsinthe opticalsystemare a. the components, the data rate and response time b. the source, the link, and the receiver c. the transmitter, the cable, and the receiver d.the source,the link,andthedetector

Description : The threemajor groupsinthe opticalsystemare a. the components, the data rate and response time b. the source, the link, and the receiver c. the transmitter, the cable, and the receiver d.the source,the link,andthedetector

Last Answer : d.the source,the link,andthedetector

DME and VOR are “frequency paired” because: a. The same receiver can be used for both aids b. The VOR transmitter is easily converted to the required DME frequency c. Cockpit workload is reduced d. Both ground transmitter aerials can be placed on the same site if required

Description : DME and VOR are “frequency paired” because: a. The same receiver can be used for both aids b. The VOR transmitter is easily converted to the required DME frequency c. Cockpit workload is reduced d. Both ground transmitter aerials can be placed on the same site if required

Last Answer : c. Cockpit workload is reduced

In the Gillette advertisement that claims "Gillette, the best a man can get," Gillette is the communication: A)receiver B)transmitter. C)decoder. D)source.

Description : In the Gillette advertisement that claims "Gillette, the best a man can get," Gillette is the communication: A)receiver B)transmitter. C)decoder. D)source.

Last Answer : D)source.

In microcontrollers, UART is acronym of_____ A. Universal Applied Receiver/Transmitter B. Universal Asynchronous Rectified Transmitter C. Universal Asynchronous Receiver/Transmitter D. United Asynchronous Receiver/Transmitter

Description : In microcontrollers, UART is acronym of_____ A. Universal Applied Receiver/Transmitter B. Universal Asynchronous Rectified Transmitter C. Universal Asynchronous Receiver/Transmitter D. United Asynchronous Receiver/Transmitter

Last Answer : C. Universal Asynchronous Receiver/Transmitter 

The skew specification of your multi-tracked tape recorder reads " +/ - 0.20 microseconds between adjacent tracks on the same head stack at 120 ips." What does this mean?

Description : The skew specification of your multi-tracked tape recorder reads " +/ - 0.20 microseconds between adjacent tracks on the same head stack at 120 ips." What does this mean?

Last Answer : One of the tracks on a magnetic head could lead or lag the track next to it by as much as 0.20 microseconds at 120 ips.

A recorder’s harmonic-distortion specification reads 2% third harmonic of a 100-kHz signal at 60 ips. What does this mean?

Description : A recorder’s harmonic-distortion specification reads 2% third harmonic of a 100-kHz signal at 60 ips. What does this mean?

Last Answer : The recorder has 2% third-harmonic distortion of a 100-kHz signal at 60 ips.

The frequency-response specification of your tape recorder reads within +/ - 3 dB from 150 Hz to 150 kHz at 60 ips. What does this mean?

Description : The frequency-response specification of your tape recorder reads within +/ - 3 dB from 150 Hz to 150 kHz at 60 ips. What does this mean?

Last Answer : The recorder can record all frequencies between 150 Hz and 150 kHz at 60 ips without varying the output amplitude more than 3 dB.

What case of a pronoun indicates that it is the receiver of an action?

Description : What case of a pronoun indicates that it is the receiver of an action?

Last Answer : An objective pronoun functions as the receiver of an action (the direct object of a verb).An objective pronoun can function as a direct object, an indirect object, or the object of a ... nice.Note: The pronoun 'her' functions as both an objective personal pronoun and a possessive adjective.

What precaution should you take when substituting a synchro tester in a circuit for a transmitter?

Description : What precaution should you take when substituting a synchro tester in a circuit for a transmitter?

Last Answer : Use only one receiver so as not to overload the tester.

Describe the zero-position of a synchro transmitter.

Description : Describe the zero-position of a synchro transmitter.

Last Answer : The transmitter is in its zero-position when the rotor is aligned with the S2 stator winding.

What unit of measurement refers to the torque of a synchro transmitter

Description : What unit of measurement refers to the torque of a synchro transmitter

Last Answer : Ounce-inches.