What is the relationship between the transmitter and receiver stator voltages when their rotors are in correspondence?

What is the relationship between the transmitter and  receiver stator voltages when their rotors are in  
correspondence?
by

1 Answer

Answer :

The voltages are equal and oppose each other.
by

Related questions

What two receiver leads are reversed to reverse the rotor's direction of rotation?

Description : What two receiver leads are reversed to reverse the rotor's direction of rotation?

Last Answer : 1 and S3.

What three things prevent a CT rotor from turning when voltages are applied to its stator windings?

Description : What three things prevent a CT rotor from turning when voltages are applied to its stator windings?

Last Answer : The rotor is specially wound, it is never connected to an ac supply, and its output is always applied to a high-impedance load.

What is the most likely problem if the transmitter shaft reads 0º when the receiver shaft indicates 180º?

Description : What is the most likely problem if the transmitter shaft reads 0º when the receiver shaft indicates 180º?

Last Answer : The rotor leads on either the transmitter or the receiver are reversed.

What is the physical difference between a synchro transmitter and a synchro receiver?

Description : What is the physical difference between a synchro transmitter and a synchro receiver?

Last Answer : A synchro receiver uses some form of damping to retard excessive oscillations or spinning.

Where should the transmitter spectrum be located with respect to the receiver response curve?

Description : Where should the transmitter spectrum be located with respect to the receiver response curve?

Last Answer : In the center.

Immediately after the transmitter fires, stc reduces the receiver gain to what level?

Description : Immediately after the transmitter fires, stc reduces the receiver gain to what level?

Last Answer : Zero.

What is the result of an impedance mismatch between a receiver or transmitter and its transmission line or antenna?

Description : What is the result of an impedance mismatch between a receiver or transmitter and its transmission line or antenna?

Last Answer : High vswr, which equates to poor reception or a loss of power output.

In a three-phase alternator, what is the phase relationship between the individual output voltages?

Description : In a three-phase alternator, what is the phase relationship between the individual output voltages?

Last Answer : Each phase is displaced 120º from the other two

What is the relationship of the voltage at C in figure 3-7 to the voltages at A and B?

Description : What is the relationship of the voltage at C in figure 3-7 to the voltages at A and B?

Last Answer : C is 1.414 times greater than A or B.

What determines the phase relationship between the voltages in a two-phase ac generator?

Description : What determines the phase relationship between the voltages in a two-phase ac generator?

Last Answer : Placement of armature coils.

Which of the two main types of rotors can have either a single winding or three Y-connected windings?

Description : Which of the two main types of rotors can have either a single winding or three Y-connected windings?

Last Answer : The drum or wound rotor.

Salient-pole rotors may be used in alternators driven by what types of prime movers?

Description : Salient-pole rotors may be used in alternators driven by what types of prime movers?

Last Answer : Internal combustion engines, water force and electric motors

In the output of an ac error detector, what indicates the (a) direction and (b) amount of control necessary for correspondence?

Description : In the output of an ac error detector, what indicates the (a) direction and (b) amount of control necessary for correspondence?

Last Answer : (a) Phase. (b) Amplitude.

A basic touch screen has three main components. It includes touch sensor, controller and ________ A. transmitter B. receiver C. software driver D. None of the Above

Description : A basic touch screen has three main components. It includes touch sensor, controller and ________ A. transmitter B. receiver C. software driver D. None of the Above

Last Answer : C. software driver

If coils 'R1-R2-R3' at the receiver of figure 'B' shown in the illustration turned opposite of those in the transmitter by design, what corrective action should be taken? EL-0092 A. Reverse the 60 Hz supply connections to 'S1' and 'S2'. B. No action is needed. C. Interchange leads 'R1' and 'R3'. D. Interchange leads 'R2' and 'R3'.

Description : If coils 'R1-R2-R3' at the receiver of figure 'B' shown in the illustration turned opposite of those in the transmitter by design, what corrective action should be taken? EL-0092 A. Reverse the 60 Hz supply ... is needed. C. Interchange leads 'R1' and 'R3'. D. Interchange leads 'R2' and 'R3'.

Last Answer : Answer: B

If coils 'R1-R2-R3' at the receiver of figure 'B' shown in the illustration were in 180 degree error with those of the transmitter, what corrective action should be taken? EL-0092 A. Reverse the 60 Hz connections to 'S1' and 'S2'. B. No action is needed as this is proper operation. C. Interchange leads 'R1' and 'R3'. D. Interchange leads 'R2' and 'R3'.

Description : If coils 'R1-R2-R3' at the receiver of figure 'B' shown in the illustration were in 180 degree error with those of the transmitter, what corrective action should be taken? EL-0092 A. Reverse the 60 Hz ... is proper operation. C. Interchange leads 'R1' and 'R3'. D. Interchange leads 'R2' and 'R3'.

Last Answer : Answer: A

If coil 'R1-R2' at the receiver of figure 'A' shown in the illustration were in 180 degree error with respect to that of the transmitter, what corrective action should be taken? EL-0092 A. No action is necessary as this is proper operation. B. Reverse the 60 Hz supply connections at 'R1' and 'R2'. C. Interchange connections 'S1' and 'S2'. D. Interchange connections 'S1' and 'S3'.

Description : If coil 'R1-R2' at the receiver of figure 'A' shown in the illustration were in 180 degree error with respect to that of the transmitter, what corrective action should be taken? EL-0092 A. No action is ... and 'R2'. C. Interchange connections 'S1' and 'S2'. D. Interchange connections 'S1' and 'S3'.

Last Answer : Answer: B

If coils 'R1-R2-R3' at the receiver of figure 'B' shown in the illustration turned opposite of those in the transmitter, what corrective action should be taken to have both turn in the same direction? EL-0092 A. Reverse the 60 Hz supply connections to 'S1' and 'S2'. B. No action is needed. C. Interchange leads 'R1' and 'R3'. D. Interchange leads 'R2' and 'R3'.

Description : If coils 'R1-R2-R3' at the receiver of figure 'B' shown in the illustration turned opposite of those in the transmitter, what corrective action should be taken to have both turn in the same direction? EL-0092 A ... is needed. C. Interchange leads 'R1' and 'R3'. D. Interchange leads 'R2' and 'R3'.

Last Answer : Answer: C

If coil 'R1-R2' at the receiver of figure 'A' shown in the illustration turned opposite of that in the transmitter, what corrective action should be taken? EL-0092 A. No action is necessary as this is normal operation. B. Reverse 60 Hz supply connections to 'R1' and 'R2'. C. Interchange connections to 'S1' and 'S2'. D. Interchange connections to 'S1' and 'S3'.

Description : If coil 'R1-R2' at the receiver of figure 'A' shown in the illustration turned opposite of that in the transmitter, what corrective action should be taken? EL-0092 A. No action is necessary as this is ... . C. Interchange connections to 'S1' and 'S2'. D. Interchange connections to 'S1' and 'S3'.

Last Answer : Answer: D

If coil 'R1-R2' on the transmitter in figure 'A' shown in the illustration is turned 30 degrees clockwise, corresponding coil 'R1-R2' on the receiver should ____________. EL-0092 A. make coils 'S1-S2-S3' turn faster because of induced currents B. ring at the receiving station until the turning stops C. receive a higher voltage depending on the turns ratio D. align itself to the same position if free to move

Description : If coil 'R1-R2' on the transmitter in figure 'A' shown in the illustration is turned 30 degrees clockwise, corresponding coil 'R1-R2' on the receiver should ____________. EL-0092 A. make coils 'S1 ... a higher voltage depending on the turns ratio D. align itself to the same position if free to move

Last Answer : Answer: D

The total propagation delay time from transmission to reception of signals from a ground transmitter to ground receiver with angle of elevation at 10 degrees respectively is A. 273 ms B. 239 ms C. 275 ms D. 260 ms

Description : The total propagation delay time from transmission to reception of signals from a ground transmitter to ground receiver with angle of elevation at 10 degrees respectively is A. 273 ms B. 239 ms C. 275 ms D. 260 ms

Last Answer : A. 273 ms

What is the delay time for satellite transmissions from earth transmitter to earth receiver? A. 0.5 s B. 1s C. 5 ms D. 0.25 s

Description : What is the delay time for satellite transmissions from earth transmitter to earth receiver? A. 0.5 s B. 1s C. 5 ms D. 0.25 s

Last Answer : A. 0.5 s

What is the delay time for satellite transmission from earth transmitter to earth receiver? A. 0.5 s B. 1.0 s C. 5 ms D. 0.25 ms

Description : What is the delay time for satellite transmission from earth transmitter to earth receiver? A. 0.5 s B. 1.0 s C. 5 ms D. 0.25 ms

Last Answer : A. 0.5 s

What limits the sensitivity of a receiver? A. The power supply of the receiver B. The power output of a transmitter C. The noise floor of the receiver D. The distance between the transmitter and receiver

Description : What limits the sensitivity of a receiver? A. The power supply of the receiver B. The power output of a transmitter C. The noise floor of the receiver D. The distance between the transmitter and receiver

Last Answer : C. The noise floor of the receiver

Which of the following is not one of the natural ways a radio wave may travel from transmitter to receiver? A. Ground wave B. Micro wave C. Sky wave D. Space wave

Description : Which of the following is not one of the natural ways a radio wave may travel from transmitter to receiver? A. Ground wave B. Micro wave C. Sky wave D. Space wave

Last Answer : B. Micro wave

A satellite transmitter operates at 4GHz with an antenna gain of 4dBi. The receiver 40000 km away has an antenna gain of 50 dBi. If the transmitter has a power of 8 W, find (ignoring feedline losses and mismatch) the EIRP in dBW. A. 50 B. 69 C. 49 D. 30

Description : A satellite transmitter operates at 4GHz with an antenna gain of 4dBi. The receiver 40000 km away has an antenna gain of 50 dBi. If the transmitter has a power of 8 W, find (ignoring feedline losses and mismatch) the EIRP in dBW. A. 50 B. 69 C. 49 D. 30

Last Answer : C. 49

What is the uplink receiver frequency if the downlink transmitter is on channel 4 (3.84 Ghz)? A. 6.065 GHz B. 6.84 GHz C. 6.65 GHz D. 6.05 GHz

Description : What is the uplink receiver frequency if the downlink transmitter is on channel 4 (3.84 Ghz)? A. 6.065 GHz B. 6.84 GHz C. 6.65 GHz D. 6.05 GHz

Last Answer : A. 6.065 GHz

What is the path attenuation between transmitter and receiver at a frequency of 1.2 Ghz and a distance of 11,000 mi? A. 119 dB B. 115dB C. 179dB D. 174dB

Description : What is the path attenuation between transmitter and receiver at a frequency of 1.2 Ghz and a distance of 11,000 mi? A. 119 dB B. 115dB C. 179dB D. 174dB

Last Answer : C. 179dB

What is the device used in fiber optic communication which consist of a receiver transmitter use to clean up and amplify digital data moving in one direction and another in the opposite direction? A. Optic compressors B. Optic retarders C. Optic isolator D. Optic regenerators

Description : What is the device used in fiber optic communication which consist of a receiver transmitter use to clean up and amplify digital data moving in one direction and another in the opposite direction? A. Optic compressors B. Optic retarders C. Optic isolator D. Optic regenerators

Last Answer : D. Optic regenerators

Who is responsible in the correctness and accuracy of transmitted information content over a data communication? A. The channel B. The transmitter and receiver C. The modem D. The bridge

Description : Who is responsible in the correctness and accuracy of transmitted information content over a data communication? A. The channel B. The transmitter and receiver C. The modem D. The bridge

Last Answer : B. The transmitter and receiver

Main basic components of a data communication are composed of the following. A. Computer, modern and router B. Computer, bridge and gateway C. Transmitter, channel and receiver D. Transmitter, computer and modem

Description : Main basic components of a data communication are composed of the following. A. Computer, modern and router B. Computer, bridge and gateway C. Transmitter, channel and receiver D. Transmitter, computer and modem

Last Answer : C. Transmitter, channel and receiver

How can receiver desensitizing be reduced? A. Increase the receiver bandwidth B. Ensure good RF shielding between the transmitter and receiver C. Increase the transmitter audio gain D. Decrease the receiver squelch, gain.

Description : How can receiver desensitizing be reduced? A. Increase the receiver bandwidth B. Ensure good RF shielding between the transmitter and receiver C. Increase the transmitter audio gain D. Decrease the receiver squelch, gain.

Last Answer : D. Decrease the receiver squelch, gain.

Referred to as a ferrite device that can be used in lieu of a duplexer to isolate a microwave transmitter and receiver when both are connected to the same antenna. A. Isolator B. Circulator C. Coupler D. Diode.

Description : Referred to as a ferrite device that can be used in lieu of a duplexer to isolate a microwave transmitter and receiver when both are connected to the same antenna. A. Isolator B. Circulator C. Coupler D. Diode.

Last Answer : B. Circulator

______ is the first component of any MATV system to received broadcast signals. A. Receiver B. Antenna C. Filter D. Transmitter

Description : ______ is the first component of any MATV system to received broadcast signals. A. Receiver B. Antenna C. Filter D. Transmitter

Last Answer : B. Antenna

ECE Board Exam March 1996 The capture area of an antenna is directly proportional to the A. frequency of the received signal B. distance between transmitter and receiver C. gain of the antenna D. power density of the signal

Description : ECE Board Exam March 1996 The capture area of an antenna is directly proportional to the A. frequency of the received signal B. distance between transmitter and receiver C. gain of the antenna D. power density of the signal

Last Answer : C. gain of the antenna

The device that is used to convert energy from one form to another is called A : Emiter B : Transducer C : Transmitter D : Receiver

Description : The device that is used to convert energy from one form to another is called A : Emiter B : Transducer C : Transmitter D : Receiver

Last Answer : B : Transducer

The device that is used to convert energy from one form to another is called A : Emiter B : Transducer C : Transmitter D : Receiver

Description : The device that is used to convert energy from one form to another is called A : Emiter B : Transducer C : Transmitter D : Receiver

Last Answer : B : Transducer

The device that is used to convert energy from one form to another is called A : Emiter B : Transducer C : Transmitter D : Receiver

Description : The device that is used to convert energy from one form to another is called A : Emiter B : Transducer C : Transmitter D : Receiver

Last Answer : B : Transducer

The device that is used to convert energy from one form to another is called A : Emiter B : Transducer C : Transmitter D : Receiver

Description : The device that is used to convert energy from one form to another is called A : Emiter B : Transducer C : Transmitter D : Receiver

Last Answer : B : Transducer

The situation when both transmitter and receiver have to work in tandem is referred to as (A) parallel (B) serial (C) synchronous (D) asynchronous

Description : The situation when both transmitter and receiver have to work in tandem is referred to as (A) parallel (B) serial (C) synchronous (D) asynchronous

Last Answer : (C) synchronous

Calculate the total rise time for a fiber-optic system if the transmitter, receiver, and cable each have a rise time of 50 nanoseconds.

Description : Calculate the total rise time for a fiber-optic system if the transmitter, receiver, and cable each have a rise time of 50 nanoseconds.

Last Answer : 86.6 nanoseconds

The three major groups of the optical system are ∙ A. the components, the data rate and the response time ∙ B. the source, the link and the receiver ∙ C. the transmitter, the cable and the receiver ∙ D. the source, the link and the detector

Description : The three major groups of the optical system are ∙ A. the components, the data rate and the response time ∙ B. the source, the link and the receiver ∙ C. the transmitter, the cable and the receiver ∙ D. the source, the link and the detector

Last Answer : B. the source, the link and the receiver

Involves compression in the transmitter after the input sample has been converted to a linear PCM code and then expansion in the receiver prior to PCM coding:

Description : Involves compression in the transmitter after the input sample has been converted to a linear PCM code and then expansion in the receiver prior to PCM coding:

Last Answer : Digital companding

The threemajor groupsinthe opticalsystemare a. the components, the data rate and response time b. the source, the link, and the receiver c. the transmitter, the cable, and the receiver d.the source,the link,andthedetector

Description : The threemajor groupsinthe opticalsystemare a. the components, the data rate and response time b. the source, the link, and the receiver c. the transmitter, the cable, and the receiver d.the source,the link,andthedetector

Last Answer : d.the source,the link,andthedetector

DME and VOR are “frequency paired” because: a. The same receiver can be used for both aids b. The VOR transmitter is easily converted to the required DME frequency c. Cockpit workload is reduced d. Both ground transmitter aerials can be placed on the same site if required

Description : DME and VOR are “frequency paired” because: a. The same receiver can be used for both aids b. The VOR transmitter is easily converted to the required DME frequency c. Cockpit workload is reduced d. Both ground transmitter aerials can be placed on the same site if required

Last Answer : c. Cockpit workload is reduced

In the Gillette advertisement that claims "Gillette, the best a man can get," Gillette is the communication: A)receiver B)transmitter. C)decoder. D)source.

Description : In the Gillette advertisement that claims "Gillette, the best a man can get," Gillette is the communication: A)receiver B)transmitter. C)decoder. D)source.

Last Answer : D)source.

In microcontrollers, UART is acronym of_____ A. Universal Applied Receiver/Transmitter B. Universal Asynchronous Rectified Transmitter C. Universal Asynchronous Receiver/Transmitter D. United Asynchronous Receiver/Transmitter

Description : In microcontrollers, UART is acronym of_____ A. Universal Applied Receiver/Transmitter B. Universal Asynchronous Rectified Transmitter C. Universal Asynchronous Receiver/Transmitter D. United Asynchronous Receiver/Transmitter

Last Answer : C. Universal Asynchronous Receiver/Transmitter 

In a series-RLC circuit, what is the condition of the circuit if there is high impedance, low current, and low reactance voltages

Description : In a series-RLC circuit, what is the condition of the circuit if there is high impedance, low current, and low reactance voltages

Last Answer : Nonresonant (circuit is either above or below resonance)

When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease (which one) in the resistance of the regulating device.

Description : When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease (which one) in the resistance of the regulating device.

Last Answer : An increase.

When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease in the resistance of the regulating device.

Description : When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease in the resistance of the regulating device.

Last Answer : Increase.