How would one squeeze more channels of communication into TDM frames of standard length? A. Shorten the time delay for each channel B. Raise the amplitude C. Add modulators D. Remove the synchronizing pulses

How would one squeeze more channels of communication into TDM frames of standard
length?
A. Shorten the time delay for each channel
B. Raise the amplitude
C. Add modulators
D. Remove the synchronizing pulses
by

1 Answer

Answer :

A. Shorten the time delay for each channel
by

Related questions

Modulation means A. Varying of information B. Utilization of a single transmission channel to carry multiple signals C. Varying of some parameters of a carrier such as its amplitude to transmit information D. Transmit pulses in DC form on a copper wire

Description : Modulation means A. Varying of information B. Utilization of a single transmission channel to carry multiple signals C. Varying of some parameters of a carrier such as its amplitude to transmit information D. Transmit pulses in DC form on a copper wire

Last Answer : C. Varying of some parameters of a carrier such as its amplitude to transmit information

One of the reasons why FDM is being replaced by TDM is A. noise is amplified with voice when an FDM system is used B. it is difficult to place channels side by side C. there is more time than frequency D. Most available frequencies has been used

Description : One of the reasons why FDM is being replaced by TDM is A. noise is amplified with voice when an FDM system is used B. it is difficult to place channels side by side C. there is more time than frequency D. Most available frequencies has been used

Last Answer : A. noise is amplified with voice when an FDM system is used

Four channels are multiplexed using TDM. If each channel sends 100 bytes/second and we multiplex 1 byte per channel, then the bit rate for the link is __________. a. 400 bps b. 800 bps c. 1600 bps d. 3200 bps

Description : Four channels are multiplexed using TDM. If each channel sends 100 bytes/second and we multiplex 1 byte per channel, then the bit rate for the link is __________. a. 400 bps b. 800 bps c. 1600 bps d. 3200 bps

Last Answer : d. 3200 bps

Four channels are multiplexed using TDM. If each channel sends 100 bytes/second and we multiplex 1 byte per channel, then the bit rate for the link is ............... (A) 400 bps (B) 800 bps (C) 1600 bps (D) 3200 bps

Description : Four channels are multiplexed using TDM. If each channel sends 100 bytes/second and we multiplex 1 byte per channel, then the bit rate for the link is ............... (A) 400 bps (B) 800 bps (C) 1600 bps (D) 3200 bps

Last Answer : (D) 3200 bps Answer: D Explanation: The multiplexer is shown in the Figure. Each frame carries 1 byte from each channel; the size of each frame, therefore, is 4 bytes, or 32 bits. Because each ... channel, the frame rate must be 100 frames per second. The bit rate is 100 32 = 3200 bps. 

Noise consisting of irregular pulses of short duration and relatively high amplitude, A. Quantizing noise B. Tone interference C. Impulse noise D. Cross talk

Description : Noise consisting of irregular pulses of short duration and relatively high amplitude, A. Quantizing noise B. Tone interference C. Impulse noise D. Cross talk

Last Answer : C. Impulse noise

Noise consisting of irregular pulses of short duration and relatively high amplitude, A. Quantizing noise B. Tone interference C. Impulse noise D. Cross talk

Description : Noise consisting of irregular pulses of short duration and relatively high amplitude, A. Quantizing noise B. Tone interference C. Impulse noise D. Cross talk

Last Answer : A. Quantizing noise

The series of periodically recurrent pulses is modulated in amplitude by the corresponding instantaneous samples. A. PFM B. PWM C. PDM D. PAM

Description : The series of periodically recurrent pulses is modulated in amplitude by the corresponding instantaneous samples. A. PFM B. PWM C. PDM D. PAM

Last Answer : D. PAM

If link transmits 4000 frames per second and each slot has 8 bits, the transmission rate of circuit of this TDM is ______. a. 64 Kbps b. 32 Mbps c. 32 Kbps d. 64 MbpS

Description : If link transmits 4000 frames per second and each slot has 8 bits, the transmission rate of circuit of this TDM is ______. a. 64 Kbps b. 32 Mbps c. 32 Kbps d. 64 MbpS

Last Answer : c. 32 Kbps

If link transmits 4000 frames per second and each slot has 8 bits, the transmission rate of circuit of this TDM is ............... (A) 64 Kbps (B) 32 Mbps (C) 32 Kbps (D) 64 Mbps

Description : If link transmits 4000 frames per second and each slot has 8 bits, the transmission rate of circuit of this TDM is ............... (A) 64 Kbps (B) 32 Mbps (C) 32 Kbps (D) 64 Mbps

Last Answer : (C) 32 Kbps

why equalizing pulses are needed. Draw the vertical synchronizing pulse structure.

Description : why equalizing pulses are needed. Draw the vertical synchronizing pulse structure.

Last Answer : The ½ line difference just prior to the start of serrated vertical pulse does not affect the horizontal deflection synchronization but it does affect the vertical synchronization and the interlaced scanning. The ... the vertical sync pulse to occur at the correct time after every field.

Digital transmission provides a higher level of signal quality than analog transmission because A. repeaters regenerate digital pulses and remove distorstion B. digital signals are easier to sample than analog signals C. digital signals are smaller than analog signals and cannot easily be distorted D. analog signals are continuous and not easily distorted.

Description : Digital transmission provides a higher level of signal quality than analog transmission because A. repeaters regenerate digital pulses and remove distorstion B. digital signals are easier to sample than ... and cannot easily be distorted D. analog signals are continuous and not easily distorted.

Last Answer : A. repeaters regenerate digital pulses and remove distorstion

What is the effect in over modulated amplitude modulated radio broadcasting transmission? A. Interference to adjacent channel B. Higher fidelity C. Increase noise D. Higher audio signal

Description : What is the effect in over modulated amplitude modulated radio broadcasting transmission? A. Interference to adjacent channel B. Higher fidelity C. Increase noise D. Higher audio signal

Last Answer : A. Interference to adjacent channel

Sources of impulse noise induced in communication channels. A. Erroneous digital coding bit caused by an error on a transmission facility B. Transients due to relay operation C. Crosstalk from dc signaling systems D. All of these

Description : Sources of impulse noise induced in communication channels. A. Erroneous digital coding bit caused by an error on a transmission facility B. Transients due to relay operation C. Crosstalk from dc signaling systems D. All of these

Last Answer : D. All of these

____________ carries signalling and synchronizing commands. a) Traffic channels b) Control channels c) Signalling channels d) Forward channels

Description : ____________ carries signalling and synchronizing commands. a) Traffic channels b) Control channels c) Signalling channels d) Forward channels

Last Answer : b) Control channels

What is transit time (time delay) of a 50-ft length transmission line of the above problem? A. 50 ns B. 100 ns C. 75 ns D. 65 ns

Description : What is transit time (time delay) of a 50-ft length transmission line of the above problem? A. 50 ns B. 100 ns C. 75 ns D. 65 ns

Last Answer : C. 75 ns

Which standard is utilized in intermodulation noise rates on PCM audio channels? A. CCIT Rec. G.151 B. CCIT Rec. G.172 C. CCIT Rec. G.190 D. CCIT Rec. G.190

Description : Which standard is utilized in intermodulation noise rates on PCM audio channels? A. CCIT Rec. G.151 B. CCIT Rec. G.172 C. CCIT Rec. G.190 D. CCIT Rec. G.190

Last Answer : B. CCIT Rec. G.172

ECE Board Exam March 1996 The number of voice band channels in master group per CCITT standard is __________. A. 300 B. 480 C. 600 D. 12

Description : ECE Board Exam March 1996 The number of voice band channels in master group per CCITT standard is __________. A. 300 B. 480 C. 600 D. 12

Last Answer : A. 300

The advantage of periscope antenna in microwave A. Minimize interference to and from other neighboring stations B. Shorten waveguide link C. Reduce tower height D. All of these

Description : The advantage of periscope antenna in microwave A. Minimize interference to and from other neighboring stations B. Shorten waveguide link C. Reduce tower height D. All of these

Last Answer : B. Shorten waveguide link

Which of the following is oldest multiplexing scheme? A. Frequency Division Multiplexing (FDM) B. Time Division Multiplexing (TDM) C. Code Division Multiplexing (CDM) D. Space Division Multiplexing (SDM)

Description : Which of the following is oldest multiplexing scheme? A. Frequency Division Multiplexing (FDM) B. Time Division Multiplexing (TDM) C. Code Division Multiplexing (CDM) D. Space Division Multiplexing (SDM)

Last Answer : D. Space Division Multiplexing (SDM)

In the North American TDM system, what is the transmission rate in Mbps of T3 carrier system? A. 44.736 B. 6.312 C. 3.152 D. 274.176

Description : In the North American TDM system, what is the transmission rate in Mbps of T3 carrier system? A. 44.736 B. 6.312 C. 3.152 D. 274.176

Last Answer : A. 44.736

Which of the following describes a TDM frame? A. A 250-μs frame B. A 125-μs frame C. A 500-μs frame D. A 60-μs frame

Description : Which of the following describes a TDM frame? A. A 250-μs frame B. A 125-μs frame C. A 500-μs frame D. A 60-μs frame

Last Answer : B. A 125-μs frame

Multiplexing scheme use by baseband transmission. A. FDM B. Space multiplexing C. TDM D. Statistical multiplexing

Description : Multiplexing scheme use by baseband transmission. A. FDM B. Space multiplexing C. TDM D. Statistical multiplexing

Last Answer : C. TDM

Who is responsible in the correctness and accuracy of transmitted information content over a data communication? A. The channel B. The transmitter and receiver C. The modem D. The bridge

Description : Who is responsible in the correctness and accuracy of transmitted information content over a data communication? A. The channel B. The transmitter and receiver C. The modem D. The bridge

Last Answer : B. The transmitter and receiver

Main basic components of a data communication are composed of the following. A. Computer, modern and router B. Computer, bridge and gateway C. Transmitter, channel and receiver D. Transmitter, computer and modem

Description : Main basic components of a data communication are composed of the following. A. Computer, modern and router B. Computer, bridge and gateway C. Transmitter, channel and receiver D. Transmitter, computer and modem

Last Answer : C. Transmitter, channel and receiver

A sender uses the Stop-and-Wait ARQ protocol for reliable transmission of frames. Frames are of size 1000 bytes and the transmission rate at the sender is 80 Kbps (1Kbps = 1000 bits/second). Size of an acknowledgement is 100 bytes and the transmission rate at the receiver is 8 Kbps. The one-way propagation delay is 100 milliseconds. Assuming no frame is lost, the sender throughput is __________ bytes/second. a. 2500 b. 2000 c. 1500 d. 500

Description : A sender uses the Stop-and-Wait ARQ protocol for reliable transmission of frames. Frames are of size 1000 bytes and the transmission rate at the sender is 80 Kbps (1Kbps = 1000 bits/second). Size of ... is lost, the sender throughput is __________ bytes/second. a. 2500 b. 2000 c. 1500 d. 500

Last Answer : a. 2500

The distance between two stations M and N is L kilometers. All frames are K bits long. The propagation delay per kilometer is t seconds. Let R bits/second be the channelcapacity. Assuming that processing delay is negligible, the minimum number of bits for the sequence number field in a frame for maximum utilization, when the sliding window protocol used is: a. A b. B c. C d. D

Description : The distance between two stations M and N is L kilometers. All frames are K bits long. The propagation delay per kilometer is t seconds. Let R bits/second be the channel capacity. Assuming that processing ... maximum utilization, when the sliding window protocol used is: a. A b. B c. C d. D

Last Answer : c. C

How far is the visual carrier from the lowest frequency in the spectrum of a monochrome TV broadcast channel following the NTSC standard? A. 1.5 MHz B. 1.25 MHz C. 4.5 MHz D. 0.25 MHz

Description : How far is the visual carrier from the lowest frequency in the spectrum of a monochrome TV broadcast channel following the NTSC standard? A. 1.5 MHz B. 1.25 MHz C. 4.5 MHz D. 0.25 MHz

Last Answer : B. 1.25 MHz

________ is the method of encoding audio signals used in US standard 1544 kbit/s 24 channel PCM systems. A. Shannon’s law B. A-law C. Newton’s law D. Mu-law

Description : ________ is the method of encoding audio signals used in US standard 1544 kbit/s 24 channel PCM systems. A. Shannon’s law B. A-law C. Newton’s law D. Mu-law

Last Answer : D. Mu-law

What do you call the service area of a standard AM broadcast where fading is allowed but not objectionable co-channel interference? A. Experimental B. Secondary C. Tertiary D. Primary

Description : What do you call the service area of a standard AM broadcast where fading is allowed but not objectionable co-channel interference? A. Experimental B. Secondary C. Tertiary D. Primary

Last Answer : B. Secondary

What is the channel bandwidth of a standard analogue telephone system? A. 300-500 Hz B. 1200 kHz C. 100-300 Hz D. 300-3400 Hz

Description : What is the channel bandwidth of a standard analogue telephone system? A. 300-500 Hz B. 1200 kHz C. 100-300 Hz D. 300-3400 Hz

Last Answer : D. 300-3400 Hz

In TDM systems, channel separation is done with the use of...

Description : In TDM systems, channel separation is done with the use of  (a) AND gates (b) band-pass filters (c) differentiator circuit (d) integrator circuit

Last Answer : a) AND gates

Multiplexing in a time division multiplexer occurs based upon A. the position of a frame within the group of frames B. the positioning of data within a frame C. the priority assigned to a connected device D. the activity of a connected device

Description : Multiplexing in a time division multiplexer occurs based upon A. the position of a frame within the group of frames B. the positioning of data within a frame C. the priority assigned to a connected device D. the activity of a connected device

Last Answer : B. the positioning of data within a frame

How can I shorten "Add fractional dimension" and still keep its meaning clear?

Description : How can I shorten "Add fractional dimension" and still keep its meaning clear?

Last Answer : How about one box for inches, another box for fractions of an inch? Otherwise you will have to parse e.g. 22 7/8 becomes 22 + (7 divided by 8)

Which ARQ mechanism deals with the transmission of only damaged or lost frames despite the other multiple frames by increasing the efficiency & its utility in noisy channels? a. GoBackN ARQ b. Selective Repeat ARQ c. StopandWait ARQ d. All of the above

Description : Which ARQ mechanism deals with the transmission of only damaged or lost frames despite the other multiple frames by increasing the efficiency & its utility in noisy channels? a. GoBackN ARQ b. Selective Repeat ARQ c. StopandWait ARQ d. All of the above

Last Answer : b. Selective Repeat ARQ

The first laser emitted a. Pulses of 694 nm red light b. A continuous red beam c. Pulses of white light from a helical flashlamp d. Spontaneous emission

Description : The first laser emitted a. Pulses of 694 nm red light b. A continuous red beam c. Pulses of white light from a helical flashlamp d. Spontaneous emission

Last Answer : a. Pulses of 694 nm red light

What is the non-continuous noise of irregular pulses or spikes of duration with high amplitudes? A. Wander B. Jitter C. Hits D. Singing

Description : What is the non-continuous noise of irregular pulses or spikes of duration with high amplitudes? A. Wander B. Jitter C. Hits D. Singing

Last Answer : B. Jitter

Modulation in which no signal is present between pulses A. Pulse modulation B. QAM C. PSK D. FSK

Description : Modulation in which no signal is present between pulses A. Pulse modulation B. QAM C. PSK D. FSK

Last Answer : A. Pulse modulation

Which of the following is not a baseband signal modulation? A. RF carrier B. Video System C. Audio signal D. Binary coded pulses

Description : Which of the following is not a baseband signal modulation? A. RF carrier B. Video System C. Audio signal D. Binary coded pulses

Last Answer : A. RF carrier

What three types of storage elements most often are used in modulators?

Description : What three types of storage elements most often are used in modulators?

Last Answer : Capacitor, artificial transmission line, or pulse-forming network.

What three types of storage elements most often are used in modulators?

Description : What three types of storage elements most often are used in modulators?

Last Answer : Capacitor, artificial transmission line, or pulse-forming network.

56 years old woman has come to you with the complaints of hot flushes irritability, joint pains with lack of sleep. Most appropriate treatment would be: a) Hysterectomy. b) Vitamins. c) Combined oestrogen, progesterone preparations. d) Phytooestrogens. e) Selective estrogen receptor modulators (SERMS).

Description : 56 years old woman has come to you with the complaints of hot flushes irritability, joint pains with lack of sleep. Most appropriate treatment would be: a) Hysterectomy. b) ... Combined oestrogen, progesterone preparations. d) Phytooestrogens. e) Selective estrogen receptor modulators (SERMS).

Last Answer : c) Combined oestrogen, progesterone preparations.

The total propagation delay time from transmission to reception of signals from a ground transmitter to ground receiver with angle of elevation at 10 degrees respectively is A. 273 ms B. 239 ms C. 275 ms D. 260 ms

Description : The total propagation delay time from transmission to reception of signals from a ground transmitter to ground receiver with angle of elevation at 10 degrees respectively is A. 273 ms B. 239 ms C. 275 ms D. 260 ms

Last Answer : A. 273 ms

What is the delay time for satellite transmissions from earth transmitter to earth receiver? A. 0.5 s B. 1s C. 5 ms D. 0.25 s

Description : What is the delay time for satellite transmissions from earth transmitter to earth receiver? A. 0.5 s B. 1s C. 5 ms D. 0.25 s

Last Answer : A. 0.5 s

What is the delay time for satellite transmission from earth transmitter to earth receiver? A. 0.5 s B. 1.0 s C. 5 ms D. 0.25 ms

Description : What is the delay time for satellite transmission from earth transmitter to earth receiver? A. 0.5 s B. 1.0 s C. 5 ms D. 0.25 ms

Last Answer : A. 0.5 s

What is the time delay introduced by a 75-ft coaxial cable with a dielectric constant of 2.3? A. 1.54 ns B. 11.5 ns C. 115.6 ns D. 1156 ns

Description : What is the time delay introduced by a 75-ft coaxial cable with a dielectric constant of 2.3? A. 1.54 ns B. 11.5 ns C. 115.6 ns D. 1156 ns

Last Answer : C. 115.6 ns

What do you call the phenomenon in digital circuits that describe the duration of time a digital signal passes a circuit? A. Transmission time B. Elapsed time C. Propagation delay D. Travel delay

Description : What do you call the phenomenon in digital circuits that describe the duration of time a digital signal passes a circuit? A. Transmission time B. Elapsed time C. Propagation delay D. Travel delay

Last Answer : C. Propagation delay

Adding staff to a project to shorten the project’s length is usually a wise move, because adding staff normally translates into increased productivity

Description : Adding staff to a project to shorten the project’s length is usually a wise move,  because adding staff normally translates into increased productivity

Last Answer : Ans: False

The _________ product defines the number ofbits that can fill the link. A) bandwidth-period B) frequency-amplitude C) bandwidth-delay D) delay-amplitude

Description : The _________ product defines the number ofbits that can fill the link. A) bandwidth-period B) frequency-amplitude C) bandwidth-delay D) delay-amplitude

Last Answer : bandwidth-delay

Suppose transmission rate of a channel is 32 kbps. If there are ‘8’ routes from source to destination and each packet p contains 8000 bits. Total end to end delay in sending packet P is _____. a. 2 sec b. 3 sec c. 4 sec d. 1 sec

Description : Suppose transmission rate of a channel is 32 kbps. If there are ‘8’ routes from source to destination and each packet p contains 8000 bits. Total end to end delay in sending packet P is _____. a. 2 sec b. 3 sec c. 4 sec d. 1 sec

Last Answer : a. 2 sec

________ dispersion is caused by the difference in the propagation times of light rays that take different paths down a fiber. a. Material dispersion b. Wavelength dispersion c. Modal dispersion d. Delay dispersion

Description : ________ dispersion is caused by the difference in the propagation times of light rays that take different paths down a fiber. a. Material dispersion b. Wavelength dispersion c. Modal dispersion d. Delay dispersion

Last Answer : c. Modal dispersion