The vertical-deflection plates are used to reproduce what function?

The vertical-deflection plates are used to reproduce what  function?
by

1 Answer

Answer :

Amplitude.
by

Related questions

The vertical-deflection plates are used to reproduce what function?

Description : The vertical-deflection plates are used to reproduce what function?

Last Answer : Amplitude.

The horizontal-deflection plates are used to produce what function?

Description : The horizontal-deflection plates are used to produce what function?

Last Answer : Time and/or frequency relationships.

The horizontal-deflection plates are used to produce what function?

Description : The horizontal-deflection plates are used to produce what function?

Last Answer : Time and/or frequency relationships.

Why are the ends of the deflection plates bent outward?

Description : Why are the ends of the deflection plates bent outward?

Last Answer : To permit wide-angle deflection of the bea

Is the deflection angle greater with higher or lower potential on the plates?

Description : Is the deflection angle greater with higher or lower potential on the plates?

Last Answer : Higher potential.

Why are the ends of the deflection plates bent outward?

Description : Why are the ends of the deflection plates bent outward?

Last Answer : To permit wide-angle deflection of the beam.

Is the deflection angle greater with higher or lower potential on the plates?

Description : Is the deflection angle greater with higher or lower potential on the plates?

Last Answer : Higher potential.

What effect do longer deflection plates have on the electron beam?

Description : What effect do longer deflection plates have on the electron beam?

Last Answer : A greater deflection angle.

The equalization and phase correction circuit in a tape recorder’s direct reproduce electronics (figure 5-2) performs what function?

Description : The equalization and phase correction circuit in a tape recorder’s direct reproduce electronics (figure 5-2) performs what function?

Last Answer : It generates an equalization signal which corrects any frequency response problems in the input signal from the pre-amplifier circuit.

How should a tape recorder with good phase response reproduce a complex waveform, such as a square wave?

Description : How should a tape recorder with good phase response reproduce a complex waveform, such as a square wave?

Last Answer : With no distortion

Two tape recorders have signal-to-noise ratios (SNRs) of 25-dB RMS and 35-dB RMS respectively. Which of the SNRs can record and reproduce the widest range of input signals and why?

Description : Two tape recorders have signal-to-noise ratios (SNRs) of 25-dB RMS and 35-dB RMS respectively. Which of the SNRs can record and reproduce the widest range of input signals and why?

Last Answer : 35-dB RMS because the highest SNR can always record and reproduce the widest range of input signals.

What is the major difference between direct reproduce electronics and FM reproduce electronics?

Description : What is the major difference between direct reproduce electronics and FM reproduce electronics?

Last Answer : FM record electronics must use a limiter and demodulator circuit (figure 5-5) to demodulate the signal intelligence from the carrier frequency.

What two types of record and reproduce electronics are used by magnetic tape recorders?

Description : What two types of record and reproduce electronics are used by magnetic tape recorders?

Last Answer : . a. Direct record (AM). b. Frequency modulation (FM).

A recorder's erase head is always placed in what sequence on the record/reproduce track?

Description : A recorder's erase head is always placed in what sequence on the record/reproduce track?

Last Answer : . First, before the record and reproduce heads.

Why are record heads always placed before reproduce heads on recorders?

Description : Why are record heads always placed before reproduce heads on recorders?

Last Answer : Allow you to monitor the signals you're recording.

Most record and reproduce heads are in one of what three bandwidth categories?

Description : Most record and reproduce heads are in one of what three bandwidth categories?

Last Answer : a. Narrowband—100 Hz to 100 kHz. b. Intermediate band—100 Hz to 500 kHz. c. Wideband—400 Hz to 2 mHz.

What two specifications determine the maximum frequency that a recorder's record and reproduce heads will be able to transfer?

Description : What two specifications determine the maximum frequency that a recorder's record and reproduce heads will be able to transfer?

Last Answer : a. Size of the headgap. b. Speed of the magnetic tape.

What does the simplest diode detector use to reproduce the modulating frequency?

Description : What does the simplest diode detector use to reproduce the modulating frequency?

Last Answer : The modulation envelope.

What kind of voltage is applied to the horizontal deflection plates of the oscilloscope?

Description : What kind of voltage is applied to the horizontal deflection plates of the oscilloscope?

Last Answer : sweep voltage

A circuit which develops voltage across the horizontal deflection plates is known as a) Time base generator b) Electron gun c) Thermionic diode d) Zener diode

Description : A circuit which develops voltage across the horizontal deflection plates is known as a) Time base generator b) Electron gun c) Thermionic diode d) Zener diode

Last Answer : a) Time base generator

The ___________ of a CRO controls the brightness of the spot formed on the screen a) Filament b) Grid c) Deflection plates d) Cathode

Description : The ___________ of a CRO controls the brightness of the spot formed on the screen a) Filament b) Grid c) Deflection plates d) Cathode

Last Answer : b) Grid

An important part of inkjet printer is: (a) Deflection plates (b) Toner (c) Drum (d) None of these

Description : An important part of inkjet printer is: (a) Deflection plates (b) Toner (c) Drum (d) None of these

Last Answer : (a) Deflection plates

If the distance of screen from a CRT to center of deflection plates is 15 cm, the length of

Description : If the distance of screen from a CRT to center of deflection plates is 15 cm, the length of deflection plates is 2 cm, the distance between the plates is 1 cm and accelerating voltage is 500 V, deflection sensitivity is   (a) 33.2 V/cm (b) 0.03 cm/V (c) 66.4 V/cm (d) 0.015 cm/V

Last Answer : If the distance of screen from a CRT to center of deflection plates is 15 cm, the length of deflection plates is 2 cm, the distance between the plates is 1 cm and accelerating voltage is 500 V, deflection sensitivity is 0.03 cm/V

Horizontal deflection plates of CRO are placed generally

Description : Horizontal deflection plates of CRO are placed generally   (a) Horizontal (b) Vertical (c) Diagonal (d) (a) or (b)  

Last Answer : Horizontal

A vertical spring-mass system has a mass of 0.5 kg and an initial deflection of 0.2 cm. Find the spring stiffness. A. 345 N/m B. 245 N/m C. 3452 N/mD. 2452 N/m

Description : A vertical spring-mass system has a mass of 0.5 kg and an initial deflection of 0.2 cm. Find the spring stiffness. A. 345 N/m B. 245 N/m C. 3452 N/mD. 2452 N/m

Last Answer : D. 2452 N/m

Pick up the correct statement from the following: (A) The structural member subjected to compression and whose dimensions are small as compared to its length, is called a stmt (B) The vertical compression members are generally known as columns or stanchions (C) Deflection in lateral direction of a long column, is generally known as buckling (D) All the above

Description : Pick up the correct statement from the following:  (A) The structural member subjected to compression and whose dimensions are small as  compared to its length, is called a stmt  (B) The ... in lateral direction of a long column, is generally known as buckling  (D) All the above

Last Answer : (D) All the above

For a continuous slab of 3 m × 3.5 m size, the minimum overall depth of slab to satisfy vertical deflection limits is (A) 50 mm (B) 75 mm (C) 100 mm (D) 120 mm

Description : For a continuous slab of 3 m × 3.5 m size, the minimum overall depth of slab to satisfy vertical deflection limits is (A) 50 mm (B) 75 mm (C) 100 mm (D) 120 mm

Last Answer : (B) 75 mm

For a cantilever of effective depth of 0.5 m, the maximum span to satisfy vertical deflection limit is (A) 3.5 m (B) 4 m (C) 4.5 m (D) 5 m

Description : For a cantilever of effective depth of 0.5 m, the maximum span to satisfy vertical deflection limit is (A) 3.5 m (B) 4 m (C) 4.5 m (D) 5 m

Last Answer : Answer: Option A

For a simply supported beam of span 15 m, the minimum effective depth to satisfy the vertical deflection limits should be (A) 600 mm (B) 750 mm (C) 900 mm (D) More than 1 m

Description : For a simply supported beam of span 15 m, the minimum effective depth to satisfy the vertical deflection limits should be (A) 600 mm (B) 750 mm (C) 900 mm (D) More than 1 m

Last Answer : Answer: Option B

For a continuous slab of 3 m x 35 m size, the minimum overall depth of slab to satisfy vertical deflection limits is (a) 120 mm (b) 100 mm (c) 75 mm (d) 50 mm

Description : For a continuous slab of 3 m x 35 m size, the minimum overall depth of slab to satisfy vertical deflection limits is (a) 120 mm (b) 100 mm (c) 75 mm (d) 50 mm

Last Answer : (a) 120 mm

The vertical distance between the axis of the beam before and after loading at a point is called as _______ a. Deformation b. Deflection c. Slope d. None of above.

Description : The vertical distance between the axis of the beam before and after loading at a point is called as _______ a. Deformation b. Deflection c. Slope d. None of above.

Last Answer : b. Deflection

Explain vertical deflection subsystem with neat diagram.

Description : Explain vertical deflection subsystem with neat diagram.

Last Answer : vertical deflection subsystem The main function of the vertical deflection system is to provide an amplified signal of prope r level toderive the vertical deflection plates without any ... suppression, reduced no nlinear effects because none of the plates are at ground potential. 

Sketch Block diagram of vertical deflection system used in CRO.

Description : Sketch Block diagram of vertical deflection system used in CRO.

Last Answer : Block diagram of vertical deflection system used in CRO

vertical deflection system and explain its operation.

Description : vertical deflection system and explain its operation.

Last Answer : The main function of the vertical deflection system , is to provide an amplified signal of proper level to derive the vertical deflection plates without any distortion. For amplification of the ... suppression, reduced nonlinear effects because none of the plates are at ground potential.

The vertical deflection of an electron beam on the screen of a CRO is measured to be 8 mm. Now, the

Description : The vertical deflection of an electron beam on the screen of a CRO is measured to be 8 mm. Now, the potential difference between the Y-plates is doubled, and simultaneously the pre-accelerating anode voltage is reduced to half of ... on the screen would become (A) 64 mm (B) 32 mm (C) 8 mm (D) 1 mm

Last Answer : The vertical deflection of an electron beam on the screen of a CRO is measured to be 8 mm. Now, the potential difference between the Y-plates is doubled, and simultaneously the pre-accelerating ... of its previous value. Then, the vertical deflection of the beam on the screen would become 32 mm

What effect does closer spacing of plates have on the electron beam?

Description : What effect does closer spacing of plates have on the electron beam?

Last Answer : A greater deflection angle.

What effect does closer spacing of plates have on the electron beam?

Description : What effect does closer spacing of plates have on the electron beam?

Last Answer : A greater deflection angle.

What type of rectifier is constructed by sandwiching a section of semiconductor material between two metal plates?

Description : What type of rectifier is constructed by sandwiching a section of semiconductor material between two metal plates?

Last Answer : Metallic rectifier.

Is the deflection angle greater when the beam is moving faster or slower?

Description : Is the deflection angle greater when the beam is moving faster or slower?

Last Answer : Slower beam.

Is the deflection angle greater when the beam is moving faster or slower?

Description : Is the deflection angle greater when the beam is moving faster or slower?

Last Answer : Slower beam.

What term is used to describe the reciprocal of deflection sensitivity of a scope?

Description : What term is used to describe the reciprocal of deflection sensitivity of a scope?

Last Answer : Deflection factor.

Which of the two types of deflection coils (fixed or rotating) is used most often?

Description : Which of the two types of deflection coils (fixed or rotating) is used most often?

Last Answer : Fixed.

What type of deflection is preferred for a crt electron beam?

Description : What type of deflection is preferred for a crt electron beam?

Last Answer : . Electromagnetic.

. A full-scale deflection on an ohmmeter scale indicates what resistance between the leads?

Description : . A full-scale deflection on an ohmmeter scale indicates what resistance between the leads?

Last Answer : Zero.

A full-scale deflection on an ohmmeter scale indicates what resistance between the leads?

Description : A full-scale deflection on an ohmmeter scale indicates what resistance between the leads?

Last Answer : Zero.

(True or False) The larger the current required to produce full-scale deflection of the meter coil, the better the sensitivity of the meter.

Description : (True or False) The larger the current required to produce full-scale deflection of the meter coil, the better the sensitivity of the meter.

Last Answer : False.

What is the polarization of the energy radiated by a vertical slot?

Description : What is the polarization of the energy radiated by a vertical slot?

Last Answer : Horizontal.

. Vertical resolution depends on what?

Description : . Vertical resolution depends on what?

Last Answer : The number of horizontal scan lines used.

If a free gyro is placed at the equator at 1200 in a vertical position; in what position should it be at 1800?

Description : If a free gyro is placed at the equator at 1200 in a vertical position; in what position should it be at 1800?

Last Answer : Horizontal.

When aligning the trace with a short applied to channel A, which control should be adjusted to bring the trace parallel to the vertical axis?

Description : When aligning the trace with a short applied to channel A, which control should be adjusted to bring the trace parallel to the vertical axis?

Last Answer : TRACE ROTATE control.