When aligning the trace with a short applied to channel A, which control should be adjusted to bring the trace parallel to the vertical axis?

When aligning the trace with a short applied to channel A,  which control should be adjusted to bring the trace parallel to  the vertical axis?
by

1 Answer

Answer :

TRACE ROTATE control.
by

Related questions

In an adjusted level, when the bubble is central, the axis of the bubble tube becomes parallel to (A) Line of sight (B) Line of collimation (C) Axis of the telescope (D) None of these

Description : In an adjusted level, when the bubble is central, the axis of the bubble tube becomes parallel to (A) Line of sight (B) Line of collimation (C) Axis of the telescope (D) None of these

Last Answer : (A) Line of sight

Which gauge is used to measure the height of rail at the time of aligning of rails for AT welding? (i) Height gauge.* (ii) Vertical gauge (iii) Horizontal gauge (iv) As decided by site supervisor

Description : Which gauge is used to measure the height of rail at the time of aligning of rails for AT welding? (i) Height gauge.* (ii) Vertical gauge (iii) Horizontal gauge (iv) As decided by site supervisor

Last Answer : (iv) As decided by site supervisor

If a target is on the bearing axis of the radiated beam, what is the input to the bearing IF channel?

Description : If a target is on the bearing axis of the radiated beam, what is the input to the bearing IF channel?

Last Answer : Zero.

Pick up the correct statement from the following: (A) The artificial barrier constructed to enclose "n area for safe anchorage, is called break water (B) The smoothened surface at the top end of the vertical face of a guay wall, is called fending (C) The effective berthing lengths of inclined guays can be adjusted (D) All the above

Description : Pick up the correct statement from the following: (A) The artificial barrier constructed to enclose "n area for safe anchorage, is called break water (B) The smoothened surface at the top end of ... fending (C) The effective berthing lengths of inclined guays can be adjusted (D) All the above

Last Answer : (D) All the above

The operation of revolving a plane table about its vertical axis so that all lines on the sheet become parallel to corresponding lines on the ground, is known (A) Levelling (B) Centering (C) Orientation (D) Setting

Description : The operation of revolving a plane table about its vertical axis so that all lines on the sheet become parallel to corresponding lines on the ground, is known (A) Levelling (B) Centering (C) Orientation (D) Setting

Last Answer : (C) Orientation

A perfectly elastic supply curve will be (a) Parallel to Y axis or a vertical line ; (b) Parallel to X axis; (c) U shaped ; (d) Downward sloping

Description : A perfectly elastic supply curve will be (a) Parallel to Y axis or a vertical line ; (b) Parallel to X axis; (c) U shaped ; (d) Downward sloping

Last Answer : the aggregate demand curve

A perfect inelastic supply curve will be (a) Parallel to Y axis or a vertical line ; (b) Parallel to X axis ; (c) U shaped; (d) Downward sloping

Description : A perfect inelastic supply curve will be (a) Parallel to Y axis or a vertical line ; (b) Parallel to X axis ; (c) U shaped; (d) Downward sloping

Last Answer : (a) Parallel to Y axis or a vertical line ;

What happens when a frequency meter is adjusted to the frequency of the signal being measured?

Description : What happens when a frequency meter is adjusted to the frequency of the signal being measured?

Last Answer : Power is absorbed by the frequency meter cavity; and a pronounced dip in power, at the output, will be observed.

.When correction preparation for re contouring of occlusal surface is to be applied, grinding only of the adjusted surface: A. Should not be felt flat B. Requires a flat crown C. Requires no contact with adjacent teeth D. Should be felt flat

Description : .When correction preparation for re contouring of occlusal surface is to be applied, grinding only of the adjusted surface: A. Should not be felt flat B. Requires a flat crown C. Requires no contact with adjacent teeth D. Should be felt flat

Last Answer : A. Should not be felt flat

A circular loop of mass m and radius r in X-Y plane of a horizontal table as shown in figure. A uniform magnetic field B is applied parallel to X-axis

Description : A circular loop of mass m and radius r in X-Y plane of a horizontal table as shown in figure. A uniform magnetic field B is applied parallel to X-axis

Last Answer : A circular loop of mass m and radius r in X-Y plane of a horizontal table as shown in figure. A uniform ... . `(mg)/(2pirB)` D. `(pirB)/(mgl)`

Pick up the correct statement from the following: (A) Detailed survey is carried out for a strip of land about 30 m at sharp curves (B) Levels are taken along the trace cut at an interval of 20 m (C) Contour interval is generally adopted at 2 metres vertical interval (D) All the above

Description : Pick up the correct statement from the following: (A) Detailed survey is carried out for a strip of land about 30 m at sharp curves (B) Levels are taken along the trace cut at an interval of 20 m (C) Contour interval is generally adopted at 2 metres vertical interval (D) All the above

Last Answer : Answer: Option D

To a person standing on shore, an object dropped from the mast of a passing sailboat will trace what path, assuming negligible air resistance. Is it: w) vertical straight line x) slanted straight line y) parabola z) hyperbola

Description : To a person standing on shore, an object dropped from the mast of a passing sailboat will trace what path, assuming negligible air resistance. Is it: w) vertical straight line x) slanted straight line y) parabola z) hyperbola

Last Answer : ANSWER: Y -- PARABOLA

To equalize the power factor of two alternators operating in parallel, the ____________. A. field excitation of both units is adjusted B. governors of both units are adjusted C. phase sequence is altered D. kilowatt load is evenly divided

Description : To equalize the power factor of two alternators operating in parallel, the ____________. A. field excitation of both units is adjusted B. governors of both units are adjusted C. phase sequence is altered D. kilowatt load is evenly divided

Last Answer : Answer: A

What is the effect on total resistance and total current in a circuit if a short occurs in (a) a parallel branch, and (b) in a series portion?

Description : What is the effect on total resistance and total current in a circuit if a short occurs in (a) a parallel branch, and (b) in a series portion?

Last Answer : (a) Total resistance decreases, total current increases (b) Total resistance decreases, total current increases

Pick up the correct statement from the following: (A) The tangent screw enables to give small movement under conditions of smooth and positive control (B) Standing on the tripod is the levelling head or trib arch (C) The levelling screws are used to tilt the instrument so that its rotation axis is truly vertical (D) All the above

Description : Pick up the correct statement from the following: (A) The tangent screw enables to give small movement under conditions of smooth and positive control (B) Standing on the tripod is the levelling head ... used to tilt the instrument so that its rotation axis is truly vertical (D) All the above

Last Answer : (D) All the above

Photoshop: Aligning Anchor Points?

Description : Photoshop: Aligning Anchor Points?

Last Answer : answer:There is no align tool for points as you would find it in Illustrator. There is a trick you can employ, however. Place a guide on your canvas. Be sure that you are snapping to ... back to Illustrator to edit the vector art with all of that Illustrator-goodness! For info on smart objects

Which one of the following is not an option for aligning data in a table? (a) justify (b) right -Technology

Description : Which one of the following is not an option for aligning data in a table? (a) justify (b) right -Technology

Last Answer : (a) justify option is not used for aligning data in a table.

Which of the diagrams shown in the illustration depicts the proper method of aligning brushes on a commutator? EL-0057 A. A B. B C. C D. D

Description : Which of the diagrams shown in the illustration depicts the proper method of aligning brushes on a commutator? EL-0057 A. A B. B C. C D. D

Last Answer : Answer: B

Which of the listed conditions might contribute to very rapid wearing of a DC machine's commutator bars? A. A grounded commutator bar B. Using improper carbon brushes C. Aligning the front and rear mica V-rings improperly D. An open circuit in the armature

Description : Which of the listed conditions might contribute to very rapid wearing of a DC machine's commutator bars? A. A grounded commutator bar B. Using improper carbon brushes C. Aligning the front and rear mica V-rings improperly D. An open circuit in the armature

Last Answer : Answer: B

Which one of the following bearing is intended for a very heavy radial load? (a) Ball bearing (b) Self-aligning roller bearing (c) Roller bearing (d) Thrust bearing

Description : Which one of the following bearing is intended for a very heavy radial load? (a) Ball bearing (b) Self-aligning roller bearing (c) Roller bearing (d) Thrust bearing

Last Answer : (b) Self-aligning roller bearing

The construction feature which makes tapered roller bearings unique in that races are (a) attachable (b) separable (c) self-aligning (d) none of the mentioned

Description : The construction feature which makes tapered roller bearings unique in that races are (a) attachable (b) separable (c) self-aligning (d) none of the mentioned

Last Answer : (b) separable

There is a problem of alignment in deep groove ball bearings. (a) Yes (b) No, it is self-aligning (c) It aligns itself only in some particular cases (d) Can’t be determined

Description : There is a problem of alignment in deep groove ball bearings. (a) Yes (b) No, it is self-aligning (c) It aligns itself only in some particular cases (d) Can’t be determined

Last Answer : (a) Yes

Match List-I (Type of Anti-friction bearing) with List-II (Specific Use) and select the using the code given below the Lists: [IES-2006] List-I List -II A. Self-aligning ball bearing 1. For pure axial load B. Taper roller bearing 2. For hinged condition C. Deep groove ball bearing 3. For pure radial load D. Thrust ball bearing 4. For axial and radial load A B C D A B C D (a) 2 1 3 4 (b) 3 4 2 1 (c) 2 4 3 1 (d) 3 1 2 4

Description : Match List-I (Type of Anti-friction bearing) with List-II (Specific Use) and select the using the code given below the Lists: [IES-2006] List-I List -II A. Self-aligning ball bearing 1. For pure axial load B. Taper roller bearing 2. For ... C D (a) 2 1 3 4 (b) 3 4 2 1 (c) 2 4 3 1 (d) 3 1 2 4

Last Answer : (c) 2 4 3 1

There is problem of alignment in deep groove ball bearings. a) Yes b) No, it is self-aligning c) It aligns itself only in some particular cases d) Can’t be determined

Description : There is problem of alignment in deep groove ball bearings. a) Yes b) No, it is self-aligning c) It aligns itself only in some particular cases d) Can’t be determined

Last Answer : a) Yes

Alignment of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. b

Description : Alignment of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. b

Last Answer : ans b

Registration of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. a

Description : Registration of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. a

Last Answer : ans a

What is the device, which depends on the action of a movalbe permanent magnet, in aligning itself in the resultant field produced by a fixed permanent magnet or current- carrying coils whose axes are displaced by a fixed angle?

Description : What is the device, which depends on the action of a movalbe permanent magnet, in aligning itself in the resultant field produced by a fixed permanent magnet or current- carrying coils whose axes are displaced by a fixed angle?

Last Answer : moving-magnet instrument

The plate voltage of a tube will vary 126 volts when a 3-volt ac signal is applied to the control grid. What is the gain of this tube?

Description : The plate voltage of a tube will vary 126 volts when a 3-volt ac signal is applied to the control grid. What is the gain of this tube?

Last Answer : 42.

The kilowatt load can be adjusted on a paralleled generator by using the _____________. A. field rheostat B. governor control C. automatic voltage regulators D. hand tachometer

Description : The kilowatt load can be adjusted on a paralleled generator by using the _____________. A. field rheostat B. governor control C. automatic voltage regulators D. hand tachometer

Last Answer : Answer: B

The frequency of an AC generator is adjusted by means of the ____________. A. main alternator field rheostat B. exciter field rheostat C. prime mover governor control D. equalizing reactor

Description : The frequency of an AC generator is adjusted by means of the ____________. A. main alternator field rheostat B. exciter field rheostat C. prime mover governor control D. equalizing reactor

Last Answer : Answer: C

The type of restrained three point linkage system in which the depth of implement is automatically adjusted to maintain a pre selected constant draft is called : E. Automatic draft control system F. Precision control system G. Depth control system H. None of the above

Description : The type of restrained three point linkage system in which the depth of implement is automatically adjusted to maintain a pre selected constant draft is called : E. Automatic draft control system F. Precision control system G. Depth control system H. None of the above

Last Answer : E. Automatic draft control system

Write short notes on: i. Stored Program Control. ii. Congestion. iii. Common channel signaling. iv. PSTN.

Description : Write short notes on: i. Stored Program Control. ii. Congestion. iii. Common channel signaling. iv. PSTN.

Last Answer : (i) Stored Program Control: In centralized control, all the control equipment is replaced by a single processor which must be quite powerful. It must be capable of processing 10 to 100 calls ... the combination of lines and switches that from a system of electrical routes through the network.  

If brushes of a D.C. generator are moved in order to bring these brushes in magnetic neutral axis, there will be?

Last Answer : If brushes of a D.C. generator are moved in order to bring these brushes in magnetic neutral axis, there will be crossmagnetisation as well as demagnetising.

A CNC Lathe is usually a machine tool with Z axes is….. a.Line Joining origin and vertical movement b.Line perpendicular to Y axis c.Both A & B d.Line Joining Chuck centre & tail stock centre

Description : A CNC Lathe is usually a machine tool with Z axes is….. a.Line Joining origin and vertical movement b.Line perpendicular to Y axis c.Both A & B d.Line Joining Chuck centre & tail stock centre

Last Answer : d.Line Joining Chuck centre & tail stock centre

A long solenoid carrying a current I is placed with its axis vertical as shown in the figure. A particle of mass m and charge q is released from the t

Description : A long solenoid carrying a current I is placed with its axis vertical as shown in the figure. A particle of mass m and charge q is released from the t

Last Answer : A long solenoid carrying a current I is placed with its axis vertical as shown in the figure. A particle of ... than g C. equal to g D. None of these

What is Plotted on the vertical or y axis?

Description : What is Plotted on the vertical or y axis?

Last Answer : the thing that you are measuring is usually plotted on the Yaxis . the X axis is usually time scale

What is measured on a vertical axis what is measured on a horizontal axis?

Description : What is measured on a vertical axis what is measured on a horizontal axis?

Last Answer : If one of the two variables is independent (or explanatory) thenit goes on the horizontal axis. Otherwise you do whatever youlike.

Which set of ordered pairs represents a vertical reflection (over the x-axis) A. (5, –1) to (–5, –1) B. (–2, –3) to (–2, 3) C. (–1, –5) to (1, 5) D. (3, –2) to (–3, –2)?

Description : Which set of ordered pairs represents a vertical reflection (over the x-axis) A. (5, –1) to (–5, –1) B. (–2, –3) to (–2, 3) C. (–1, –5) to (1, 5) D. (3, –2) to (–3, –2)?

Last Answer : help me plz

The specific humidity scale on a psychrometric chart is along the: a. Bottom horizontal axis b. Right side vertical axis c. Top horizontal axis at the top of the chart d. Left saturation line e. Left-side vertical axis and left side

Description : The specific humidity scale on a psychrometric chart is along the: a. Bottom horizontal axis b. Right side vertical axis c. Top horizontal axis at the top of the chart d. Left saturation line e. Left-side vertical axis and left side

Last Answer : Answer: B

The dry-bulb temperature scale is read on a psychrometric chart along the: a. Left vertical axis b. Right vertical axis c. Saturation line and sloping downward to the right d. Top horizontal axis e. Horizontal axis on the bottom of the chart

Description : The dry-bulb temperature scale is read on a psychrometric chart along the: a. Left vertical axis b. Right vertical axis c. Saturation line and sloping downward to the right d. Top horizontal axis e. Horizontal axis on the bottom of the chart

Last Answer : ANSWER : E

In BCG Matrix, what is the label of the Vertical axis? a. Relative Market share b. Business Strength c. Industry Growth Rate d. Market Growth Rate

Description : In BCG Matrix, what is the label of the Vertical axis? a. Relative Market share b. Business Strength c. Industry Growth Rate d. Market Growth Rate

Last Answer : Industry Growth Rate

For a fluid rotating at constant angular velocity about vertical axis as a rigid body, the pressure intensity varies as the (A) Square of the radial distance (B) Radial distance linearly (C) Inverse of the radial distance(D) Elevation along vertical direction

Description : For a fluid rotating at constant angular velocity about vertical axis as a rigid body, the pressure intensity varies as the (A) Square of the radial distance (B) Radial distance linearly (C) Inverse of the radial distance (D) Elevation along vertical direction

Last Answer : (A) Square of the radial distance

While rotating the theodolite in the horizontal plane, the bubble of the bubble tube takes up the same position in its tube, it indicates (A) The rotation axis is vertical (B) The trunnion axis is horizontal (C) The line of collimation is perpendicular to vertical axis (D) None of the above

Description : While rotating the theodolite in the horizontal plane, the bubble of the bubble tube takes up the  same position in its tube, it indicates  (A) The rotation axis is vertical  (B) The trunnion ... (C) The line of collimation is perpendicular to vertical axis  (D) None of the above

Last Answer : (A) The rotation axis is vertical

A theodolite is said to be in perfect adjustment if (A) Rotation axis is vertical to the transit axis (B) Transit axis is perpendicular to line of collimation (C) Line of collimation sweeps out a vertical plane while the telescope is elevated or depressed (D) All the above

Description : A theodolite is said to be in perfect adjustment if (A) Rotation axis is vertical to the transit axis (B) Transit axis is perpendicular to line of collimation (C) Line of collimation sweeps out a vertical plane while the telescope is elevated or depressed (D) All the above

Last Answer : (D) All the above

A transit is oriented by setting its vernier A to read the back azimuth of the preceding line. A back sight on the preceding transit station taken and transit is rotated about its vertical axis. The vernier A reads (A) Azimuth of the forward line (B) Bearing of the forward line (C) Back bearing of the forward line (D) Equal to 360°-azimuth of the forward line

Description : A transit is oriented by setting its vernier A to read the back azimuth of the preceding line. A back sight on the preceding transit station taken and transit is rotated about its vertical axis. The vernier ... (C) Back bearing of the forward line (D) Equal to 360°-azimuth of the forward line

Last Answer : (A) Azimuth of the forward line

In a perfect prismatic compass (A) Magnetic axis and geometric axis of the needle coincide (B) Ends of the needle and pivot are in same vertical and horizontal planes (C) Pivot is vertically over the centre of the graduated circle (D) All the above

Description : In a perfect prismatic compass (A) Magnetic axis and geometric axis of the needle coincide (B) Ends of the needle and pivot are in same vertical and horizontal planes (C) Pivot is vertically over the centre of the graduated circle (D) All the above

Last Answer : (D) All the above

The vertical angle between longitudinal axis of a freely suspended magnetic needle and a horizontal line at its pivot, is known (A) Declination (B) Azimuth (C) Dip (D) Bearing

Description : The vertical angle between longitudinal axis of a freely suspended magnetic needle and a horizontal line at its pivot, is known (A) Declination (B) Azimuth (C) Dip (D) Bearing

Last Answer : (C) Dip