The frequency range of a waveguide is determined by what dimensions?

The frequency range of a waveguide is determined by what  dimensions?
by

1 Answer

Answer :

. The "a" dimension.
by

Related questions

What happens to the bus bar dimensions of the waveguide when the frequency is increased?

Description : What happens to the bus bar dimensions of the waveguide when the frequency is increased?

Last Answer : The bus bar becomes wider.

Choose which of following condition is not required for a waveguide to exist. a) The dimensions should be in accordance with desired frequency b) Cut-off frequency should be minimum 6GHz c) The shape should be spherical d) No specific condition is required for waveguide design

Description : Choose which of following condition is not required for a waveguide to exist. a) The dimensions should be in accordance with desired frequency b) Cut-off frequency should be minimum 6GHz c) The shape should be spherical d) No specific condition is required for waveguide design

Last Answer : c) The shape should be spherical

What determines the frequency, bandwidth, and power handling capability of a waveguide probe?

Description : What determines the frequency, bandwidth, and power handling capability of a waveguide probe?

Last Answer : Size and shape

When the frequency is decreased so that two quarter wavelengths are longer than the "a" (wide) dimension of the waveguide, what will happen?

Description : When the frequency is decreased so that two quarter wavelengths are longer than the "a" (wide) dimension of the waveguide, what will happen?

Last Answer : Energy will no longer pass through the waveguide.

What is the most likely cause of losses in waveguide systems?

Description : What is the most likely cause of losses in waveguide systems?

Last Answer : Improperly connected joints or damaged inner surface.

What is the most common type of waveguide joint?

Description : What is the most common type of waveguide joint?

Last Answer : Choke joint.

A waveguide bend must have what minimum radius?

Description : A waveguide bend must have what minimum radius?

Last Answer : Greater than 2 wavelengths.

What is the result of an abrupt change in the size, shape, or dielectric of a waveguide?

Description : What is the result of an abrupt change in the size, shape, or dielectric of a waveguide?

Last Answer : Reflections.

When a waveguide is terminated in a resistive load, the load must be matched to what property of the waveguide?

Description : When a waveguide is terminated in a resistive load, the load must be matched to what property of the waveguide?

Last Answer : . Characteristic impedance.

What device is used to produce a gradual change in impedance at the end of a waveguide?

Description : What device is used to produce a gradual change in impedance at the end of a waveguide?

Last Answer : Horn.

What is the result of an impedance mismatch in a waveguide?

Description : What is the result of an impedance mismatch in a waveguide?

Last Answer : Standing waves that cause power losses, a reduction in power handling capability, and an increase in frequency and sensitivity.

Loose or inefficient coupling of energy into or out of a waveguide can be accomplished by the use of what method?

Description : Loose or inefficient coupling of energy into or out of a waveguide can be accomplished by the use of what method?

Last Answer : Slots and apertures.

Which subscript, in circular waveguide classification, indicates the number of full-wave patterns around the circumference?

Description : Which subscript, in circular waveguide classification, indicates the number of full-wave patterns around the circumference?

Last Answer : First.

The electric field is perpendicular to the "a" dimension of a waveguide in what mode?

Description : The electric field is perpendicular to the "a" dimension of a waveguide in what mode?

Last Answer : TE.

How is the cutoff wavelength of a circular waveguide figured?

Description : How is the cutoff wavelength of a circular waveguide figured?

Last Answer : 1.71 times the diameter.

What field configuration is easiest to produce in a given waveguide?

Description : What field configuration is easiest to produce in a given waveguide?

Last Answer : . Dominant mode

What term is used to identify the forward progress velocity of wavefronts in a waveguide?

Description : What term is used to identify the forward progress velocity of wavefronts in a waveguide?

Last Answer : Group velocity.

incidence and reflection that are perpendicular to the waveguide walls?

Description : incidence and reflection that are perpendicular to the waveguide walls?

Last Answer : Cutoff frequency.

Assuming the wall of a waveguide is perfectly flat, what is the angular relationship between the angle of incidence and the angle of reflection

Description : Assuming the wall of a waveguide is perfectly flat, what is the angular relationship between the angle of incidence and the angle of reflection

Last Answer : The angles are equal.

When a wavefront is radiated into a waveguide, what happens to the portions of the wavefront that do not satisfy the boundary conditions?

Description : When a wavefront is radiated into a waveguide, what happens to the portions of the wavefront that do not satisfy the boundary conditions?

Last Answer : Decrease to zero.

What interaction causes energy to travel down a waveguide?

Description : What interaction causes energy to travel down a waveguide?

Last Answer : The interaction of the electric and magnetic fields.

The large surface area of a waveguide greatly reduces what type of loss that is common in two-wire and coaxial lines?

Description : The large surface area of a waveguide greatly reduces what type of loss that is common in two-wire and coaxial lines?

Last Answer : Copper loss.

The folded waveguide in a bwo serves the same purpose as what component in a twt?

Description : The folded waveguide in a bwo serves the same purpose as what component in a twt?

Last Answer : Helix.

How does a waveguide-type lens focus spherical wavefront microwave energy?

Description : How does a waveguide-type lens focus spherical wavefront microwave energy?

Last Answer : Some wavefronts are accelerated so that all wavefronts exit the lens at the same time

Which dispersion mechanism (material or waveguide) is a function of the size of the fiber's core relative to the wavelength of operation?

Description : Which dispersion mechanism (material or waveguide) is a function of the size of the fiber's core relative to the wavelength of operation?

Last Answer : Waveguide dispersion.

In a waveguide, what is a frequency that would cause angles of incidence and reflection to be zero degrees?

Description : In a waveguide, what is a frequency that would cause angles of incidence and reflection to be zero degrees?

Last Answer : Critical Frequency

At what frequency compared to the cutoff frequency of a waveguide will the wavefronts be reflected back and forth across the guide (setting up standing waves) and no energy

Description : At what frequency compared to the cutoff frequency of a waveguide will the wavefronts be reflected back and forth across the guide (setting up standing waves) and no energy

Last Answer : UHF receiving antenna

Define the term w.r.t. waveguide: (i) Cut-OFF frequency (ii) Group Velocity

Description : Define the term w.r.t. waveguide: (i) Cut-OFF frequency (ii) Group Velocity

Last Answer : Group velocity: It is defined as the rate at which the wave propagates through the waveguide and is given by The group velocity is also can be defined as the velocity of energy flow ... rectangular waveguide at a frequency below fc TE1,0. This is absolute cut off frequency of the waveguide.

A rectangular waveguide is 5.1 cm by 2.4 cm (inside dimension). The cut off frequency of the dominant mode is

Description : A rectangular waveguide is 5.1 cm by 2.4 cm (inside dimension). The cut off frequency of the dominant mode is

Last Answer : A rectangular waveguide is 5.1 cm by 2.4 cm (inside dimension). The cut off frequency of the dominant mode is 2.94 GHz

A rectangular waveguide is 4.2 cm by 1.85 cm. The cut-off frequency of the dominant mode through this

Description : A rectangular waveguide is 4.2 cm by 1.85 cm. The cut-off frequency of the dominant mode through this waveguide is  (a) 3.57 GHz (b) 3.75 GHz (c) 3.70 MHz (d) 3.57 MHz

Last Answer : A rectangular waveguide is 4.2 cm by 1.85 cm. The cut-off frequency of the dominant mode through this waveguide is  3.57 GHz 

What is the typical frequency range about the center frequency of a tunable magnetron?

Description : What is the typical frequency range about the center frequency of a tunable magnetron?

Last Answer : . ±5 percent.

What is the frequency range of magnetron oscillators?

Description : What is the frequency range of magnetron oscillators?

Last Answer : 600-30,000 megahertz.

What is the typical frequency range about the center frequency of a tunable magnetron?

Description : What is the typical frequency range about the center frequency of a tunable magnetron?

Last Answer : ±5 percent.

What is the frequency range of magnetron oscillators?

Description : What is the frequency range of magnetron oscillators?

Last Answer : . 600-30,000 megahertz.

What limits the tuning range around the center frequency of a reflex klystron in a particular mode of operation?

Description : What limits the tuning range around the center frequency of a reflex klystron in a particular mode of operation?

Last Answer : The half-power points of the mode.

Which of the two types of magnetic tape is used to record audio and instrumentation type signals in the VLF to 2.5MHz frequency range?

Description : Which of the two types of magnetic tape is used to record audio and instrumentation type signals in the VLF to 2.5MHz frequency range?

Last Answer : Analog magnetic tape.

How can the frequency range of a collinear array be increased?

Description : How can the frequency range of a collinear array be increased?

Last Answer : By increasing the lengths of the elements of the array.

Which has a wider frequency range, a simple dipole or a folded dipole?

Description : Which has a wider frequency range, a simple dipole or a folded dipole?

Last Answer : Folded dipole.

What are the dimensions of the "Maytag MMV5207BAS 2.0 CuFt Over-the-Range Microwave Oven - Stainless Steel" product?

Description : What are the dimensions of the "Maytag MMV5207BAS 2.0 CuFt Over-the-Range Microwave Oven - Stainless Steel" product?

Last Answer : The dimensions of this microwave are 29.875 In. x 16.9375 In. x 17.40625 In.

select the correct response from the choices given in the parentheses. Q-20. In a closed-loop configuration the output signal is determined by (the input signal, the feedback signal, both).

Description : select the correct response from the choices given in the parentheses. Q-20. In a closed-loop configuration the output signal is determined by (the input signal, the feedback signal, both).

Last Answer : Both the input signal and the feedback signal.

What characteristic is determined by the time required for a voltage wave to travel from the input end of an artificial transmission line to the output end and back again?

Description : What characteristic is determined by the time required for a voltage wave to travel from the input end of an artificial transmission line to the output end and back again?

Last Answer : Pulse width

What characteristic is determined by the time required for a voltage wave to travel from the input end of an artificial transmission line to the output end and back again?

Description : What characteristic is determined by the time required for a voltage wave to travel from the input end of an artificial transmission line to the output end and back again?

Last Answer : Pulse width.

The amount of precession that results from a given force is determined by what quantity?

Description : The amount of precession that results from a given force is determined by what quantity?

Last Answer : Rigidity.

Low-order and high-order modes propagate along an optical fiber. How are modes determined to be low-order or high order modes?

Description : Low-order and high-order modes propagate along an optical fiber. How are modes determined to be low-order or high order modes?

Last Answer : Depends on the bending caused by the velocity difference of the wave traveling through different mediums

How is the dielectric strength of an insulator determined?

Description : How is the dielectric strength of an insulator determined?

Last Answer : By raising the voltage on a test sample until it breaks down.

How is the type of battery most easily determined?

Description : How is the type of battery most easily determined?

Last Answer : By looking at the nameplate data.

Te dimensions of frequency are a.107 dynes b.MLT c.L-1 d.T-1 e.L-1T-1

Description : Te dimensions of frequency are a.107 dynes b.MLT c.L-1 d.T-1 e.L-1T-1

Last Answer : d. T-1

For the same dimensions of the shaft which of the following has the greater natural frequency? A. Transverse B. Longitudinal C. Depends on thickness D. Depends upon length

Description : For the same dimensions of the shaft which of the following has the greater natural frequency? A. Transverse B. Longitudinal C. Depends on thickness D. Depends upon length

Last Answer : B. Longitudinal

For the same dimensions of the shaft which of the following has the greater natural frequency? (A) Transverse (B) Longitudinal (C) Depends on thickness (D) Depends upon length

Description : For the same dimensions of the shaft which of the following has the greater natural frequency? (A) Transverse (B) Longitudinal (C) Depends on thickness (D) Depends upon length

Last Answer : (B) Longitudinal

For the same dimensions of the shaft which of the following has the greater natural frequency? a) Transverse b) Longitudinal c) Depends on thickness d) Depends upon length

Description : For the same dimensions of the shaft which of the following has the greater natural frequency? a) Transverse b) Longitudinal c) Depends on thickness d) Depends upon length

Last Answer : b) Longitudinal