A crow bar is a power supply circuit that provides A) Conventional current limiting B) Foldback current. limiting C) Temperature control D) Voltage limiting.

A crow bar is a power supply circuit that provides
A) Conventional current limiting
B) Foldback current. limiting
C) Temperature control
D) Voltage limiting.
by

1 Answer

Answer :

D) Voltage limiting.
by

Related questions

Foldback current limiting has the advantage of A) Better pass transistor protection for long term overloads B) A defined turn on point C) Circuit simplicity D) All of the above.

Description : Foldback current limiting has the advantage of A) Better pass transistor protection for long term overloads B) A defined turn on point C) Circuit simplicity D) All of the above.

Last Answer : A) Better pass transistor protection for long term overloads

Load regulation is a measure of a power supplies ability keep a constant output under conditions of changing A) Line voltage B) Current demand C) Temperature D) Oscillator frequency.

Description : Load regulation is a measure of a power supplies ability keep a constant output under conditions of changing A) Line voltage B) Current demand C) Temperature D) Oscillator frequency.

Last Answer : A) Line voltage

The major function of transistor. Q2 is A) It provides voltage gain B) It provides the feedback signal C) It isolates the oscillator from loading effects D) It provides a phase shift.

Description : The major function of transistor. Q2 is A) It provides voltage gain B) It provides the feedback signal C) It isolates the oscillator from loading effects D) It provides a phase shift.

Last Answer : ) It provides a phase shift.

The ideal characteristic of a voltage stablizer is A) constant output voltage with low internal resistance B) constant output current with low internal resistance C) constant output voltage with high internal resistance D) constant internal resistance with variable output voltage.

Description : The ideal characteristic of a voltage stablizer is A) constant output voltage with low internal resistance B) constant output current with low internal resistance C) constant output voltage with high internal resistance D) constant internal resistance with variable output voltage.

Last Answer : A) constant output voltage with low internal resistance

If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the input signal C) Need for high dc collector supply D) Clipping of output in the negative half of the input signal

Description : If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the ... for high dc collector supply D) Clipping of output in the negative half of the input signal

Last Answer : B) Clipping of output in the positive half of the input signal

Current limited power supplies can prevent damage to A) Rectifier diodes and power transformers. B) Pass transistors C) Other circuits in the system D) All of the above.

Description : Current limited power supplies can prevent damage to A) Rectifier diodes and power transformers. B) Pass transistors C) Other circuits in the system D) All of the above.

Last Answer : D) All of the above.

In an amplifier the collector voltage equals the full V+ of 28 V instead of the normal 12 V which of the following can be the trouble? A) RL is open B) Cc is open C) RE is open D) CE is shorted.

Description : In an amplifier the collector voltage equals the full V+ of 28 V instead of the normal 12 V which of the following can be the trouble? A) RL is open B) Cc is open C) RE is open D) CE is shorted.

Last Answer : B) Cc is open

An ideal voltage amplifier should have A) Ri = 0, R0 = 0 B) Ri = 0, R0 =∞ C) Ri = ∞, R0 = 0 D) Ri = ∞, R0 = ∞.

Description : An ideal voltage amplifier should have A) Ri = 0, R0 = 0 B) Ri = 0, R0 =∞ C) Ri = ∞, R0 = 0 D) Ri = ∞, R0 = ∞.

Last Answer : C) Ri = ∞, R0 = 0

Which of the following methods cannot be used to increase the bandwidth for cascaded RF amplifier stages? A) Wave traps in each stage B) Stagger tuning C) A shunt damping resistor across each tuned circuit D) Doubled tuned transformers with tighter coupling

Description : Which of the following methods cannot be used to increase the bandwidth for cascaded RF amplifier stages? A) Wave traps in each stage B) Stagger tuning C) A shunt damping resistor across each tuned circuit D) Doubled tuned transformers with tighter coupling

Last Answer : A) Wave traps in each stage

Which of the following circuit would be preferred for a 455 kHz IF amplifier? A) A resistance loaded B) Double tuned transformer C) Video amplifier D) Class C

Description : Which of the following circuit would be preferred for a 455 kHz IF amplifier? A) A resistance loaded B) Double tuned transformer C) Video amplifier D) Class C

Last Answer : B) Double tuned transformer

A series mode crystal is marked 10.000 MHz., It is used in a circuit that operates the crystal in its parallel mode. The circuit can be expected to A) Run below 10 MHz B) Run at 10 MHz C) Run above 10 MHz D) Not oscillate.

Description : A series mode crystal is marked 10.000 MHz., It is used in a circuit that operates the crystal in its parallel mode. The circuit can be expected to A) Run below 10 MHz B) Run at 10 MHz C) Run above 10 MHz D) Not oscillate.

Last Answer : C) Run above 10 MHz

Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback

Description : Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback

Last Answer : C) All oscillators generate sine waves

An oscillator that uses crystal control should be A) Frequency stable B) useful only at low frequencies C) AVFO D) none of the above.

Description : An oscillator that uses crystal control should be A) Frequency stable B) useful only at low frequencies C) AVFO D) none of the above.

Last Answer : A) Frequency stable

The change in base current will be A) 0.66 micro ampere B) 6.6 micro amperes C) 66 micro amperes D) 660 micro amperes.

Description : The change in base current will be A) 0.66 micro ampere B) 6.6 micro amperes C) 66 micro amperes D) 660 micro amperes.

Last Answer : A) 0.66 micro ampere

As compared to a CB amplifier, a CE amplifier has A) Lower current amplification B) Higher current amplification C) Higher input resistance. D) Both (B) & (C)

Description : As compared to a CB amplifier, a CE amplifier has A) Lower current amplification B) Higher current amplification C) Higher input resistance. D) Both (B) & (C)

Last Answer : D) Both (B) & (C)

In general, MOV devices are used to protect electronic equipment from dangerous operating conditions such as A) High temperatures B) Line transients C) Over current D) All of the above.

Description : In general, MOV devices are used to protect electronic equipment from dangerous operating conditions such as A) High temperatures B) Line transients C) Over current D) All of the above.

Last Answer : D) All of the above.

A IGFET is a A) Linear device B) Square law device C) Half power device D) 3/2 power law device.

Description : A IGFET is a A) Linear device B) Square law device C) Half power device D) 3/2 power law device.

Last Answer : B) Square law device

In an amplifier if conductor during the cycle is from 0 to 90° and again from 180° to 270°, the amplifier will be termed as A) Class A B) Class B C) Class C D) Class AB.

Description : In an amplifier if conductor during the cycle is from 0 to 90° and again from 180° to 270°, the amplifier will be termed as A) Class A B) Class B C) Class C D) Class AB.

Last Answer : B) Class B

Which distortion is least objectionable in case of audio amplifers? A) Phase distortion B) Frequency distortion C) Harmonic distortion D) Inter modulation distortion.

Description : Which distortion is least objectionable in case of audio amplifers? A) Phase distortion B) Frequency distortion C) Harmonic distortion D) Inter modulation distortion.

Last Answer : A) Phase distortion

A push pull amplifier balances out A) Odd harmonics B) Even harmonics C) Both odd as well as even harmonics D) Neither odd nor even harmonics.

Description : A push pull amplifier balances out A) Odd harmonics B) Even harmonics C) Both odd as well as even harmonics D) Neither odd nor even harmonics.

Last Answer : A) Odd harmonics

Which amplifier will be preferred for highest gain? A) Darlington's pair B) Cascade amplifier C) Cascode amplifier D) Depends on the circuitry

Description : Which amplifier will be preferred for highest gain? A) Darlington's pair B) Cascade amplifier C) Cascode amplifier D) Depends on the circuitry

Last Answer : C) Cascode amplifier

Which of the following contributes to harmonics distortion in amplifiers? A) Positive feedback B) Presence of noise C) Defective active device D) Non linearity in active device.

Description : Which of the following contributes to harmonics distortion in amplifiers? A) Positive feedback B) Presence of noise C) Defective active device D) Non linearity in active device.

Last Answer : D) Non linearity in active device.

In a resistance loaded amplifier, the gain decreases a high frequencies because A) Of decreasing reactance of the stray CT B) Increasing reactance of the stray CT C) Increasing reactance of CC D) Decreasing reactance of CC.

Description : In a resistance loaded amplifier, the gain decreases a high frequencies because A) Of decreasing reactance of the stray CT B) Increasing reactance of the stray CT C) Increasing reactance of CC D) Decreasing reactance of CC.

Last Answer : D) Decreasing reactance of CC.

An FET has a gate source bias of 2 V. The ac input signal is ± 1.2 V. The class of operation is A) A B) B C) C D) AB

Description : An FET has a gate source bias of 2 V. The ac input signal is ± 1.2 V. The class of operation is A) A B) B C) C D) AB

Last Answer : D) AB

In a resistance loaded, RC coupled amplifier the dc component is blocked by A) Load resistance RL B) Coupling capacitor, CC C) RB D) The transistor.

Description : In a resistance loaded, RC coupled amplifier the dc component is blocked by A) Load resistance RL B) Coupling capacitor, CC C) RB D) The transistor.

Last Answer : B) Coupling capacitor, CC

Which of the following combinations has no phase inversion of the signal? A) Two CE stages B) CE and CC stages C) Three CE stages D) CE stage and emitter follower.

Description : Which of the following combinations has no phase inversion of the signal? A) Two CE stages B) CE and CC stages C) Three CE stages D) CE stage and emitter follower.

Last Answer : A) Two CE stages

The Darlington pair consists of the following two stages A) CE and CC B) Both C) Both CC D) CE and CB

Description : The Darlington pair consists of the following two stages A) CE and CC B) Both C) Both CC D) CE and CB

Last Answer : C) Both CC

Common base configuration is little used because A) It has low input impedance B) It has high input impedance C) It does not heat up D) It has very high gain.

Description : Common base configuration is little used because A) It has low input impedance B) It has high input impedance C) It does not heat up D) It has very high gain.

Last Answer : A) It has low input impedance

What is the phase relationship of the signal at the collector of Q2 to the signal at the collector of Q, A) 0° B) 90° C) 180° D) 360°.

Description : What is the phase relationship of the signal at the collector of Q2 to the signal at the collector of Q, A) 0° B) 90° C) 180° D) 360°.

Last Answer : C) 180°

Six (6) MHz crystal oscillator has a stability of 1 part in 106. The largest frequency error expected of this crystals A) 0.06 Hz B) 0.6 Hz C) 6 Hz D) 60 Hz.

Description : Six (6) MHz crystal oscillator has a stability of 1 part in 106. The largest frequency error expected of this crystals A) 0.06 Hz B) 0.6 Hz C) 6 Hz D) 60 Hz.

Last Answer : C) 6 Hz

What conditions are required for an amplifier to oscillate A) There must be feedback B) The feedback must be in phase C) The gain must be greater than the loss D) All the above are regd.

Description : What conditions are required for an amplifier to oscillate A) There must be feedback B) The feedback must be in phase C) The gain must be greater than the loss D) All the above are regd.

Last Answer : B) The feedback must be in phase

The Bandwidth of an RC-coupled amplifier is limited by: A) coupling capacitors at the low frequency end and bypass capacitors at the high frequency end B) coupling capacitors at the high frequency end and bypass capacitors at the low frequency end C) bypass and coupling capacitors at the low frequency end and shunt capacitors at the high frequency end and D) shunt capacitors at the low frequency end and bypass as well as coupling capacitors at the high frequency end.

Description : The Bandwidth of an RC-coupled amplifier is limited by: A) coupling capacitors at the low frequency end and bypass capacitors at the high frequency end B) coupling capacitors at the high frequency ... at the low frequency end and bypass as well as coupling capacitors at the high frequency end.

Last Answer : C) bypass and coupling capacitors at the low frequency end and shunt capacitors at the high frequency end and

If a circuit breaker that utilizes built-in, current limiting fuses (CLF's) cannot be closed, the problem may be traced to __________. A. a blown CLF plunger holding the trip bar in the open position B. a missing CLF C. a misaligned limiter housing assembly D. all of the above

Description : If a circuit breaker that utilizes built-in, current limiting fuses (CLF's) cannot be closed, the problem may be traced to __________. A. a blown CLF plunger holding the trip bar in the open position B. a missing CLF C. a misaligned limiter housing assembly D. all of the above

Last Answer : Answer: D

When troubleshooting electronic equipment, the FIRST step to be taken before testing the circuit voltage is to _________. A. set the meter to the lowest range B. check the voltage supply from the power source C. remove the suspected component D. check the current flow through the circuit

Description : When troubleshooting electronic equipment, the FIRST step to be taken before testing the circuit voltage is to _________. A. set the meter to the lowest range B. check the voltage supply from the power source C. remove the suspected component D. check the current flow through the circuit

Last Answer : Answer: B

A supply of 24 V DC is applied across a circuit which consist of three resistors connected in parallel R1= 1.2KΩ, R2= 560 Ω, R3= 2.1Ω and a fourth resistor of 7.8 Ω connected in series with the parallel group. Determine the current, voltage and power across each resistor

Last Answer : Req= (1/1200 +1/560 + 1/2.1)^-1        = 2.1 ohms RT= 2.1 + 7.8      = 9.9 ohms IT = V/R = 24/9.9                = 2.4 A Veq= R I =  2.1 2 ... 7.8         = 12.096 w                 = 44.928 w _________________________________________ By: Ellis-Junior Kamatjipose [email protected]

The variable resistance placed in the rotor circuit of a wound-rotor induction motor provides for __________. A. speed control B. frequency control C. voltage control D. use as a split-phase motor

Description : The variable resistance placed in the rotor circuit of a wound-rotor induction motor provides for __________. A. speed control B. frequency control C. voltage control D. use as a split-phase motor

Last Answer : Answer: A

Which one is not the basic electrical protection measures in the Philippine Electronics Code? A. Voltage/ current limiting and interrupting B. Undergrounding C. Grounding and bonding D. Shielding

Description : Which one is not the basic electrical protection measures in the Philippine Electronics Code? A. Voltage/ current limiting and interrupting B. Undergrounding C. Grounding and bonding D. Shielding

Last Answer : B. Undergrounding

What is the function of a fuse wire? (a) To prevent an unduly high electric current from passing through a circuit (b) To increase the current supply (c) To decrease the current supply (d) To stabilise the voltage

Description : What is the function of a fuse wire? (a) To prevent an unduly high electric current from passing through a circuit (b) To increase the current supply (c) To decrease the current supply (d) To stabilise the voltage

Last Answer : Ans:(a)

A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, what is the antenna current at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Last Answer : D. 2.0 A

Does conventional current return to the positive or negative terminal of the voltage source?

Description : Does conventional current return to the positive or negative terminal of the voltage source? 

Last Answer : Dear shimroz123, Conventional current flowing form positive terminals to negative terminals Sincerely  Masjed Gul Popal  EEE

Two 100 watt light bulbs are connected in parallel across a 100 volt power supply. The total power developed in the circuit is _______________. A. 200 watts B. 100 watts C. 50 watts D. equal to the product of the amperes times the voltage in each branch

Description : Two 100 watt light bulbs are connected in parallel across a 100 volt power supply. The total power developed in the circuit is _______________. A. 200 watts B. 100 watts C. 50 watts D. equal to the product of the amperes times the voltage in each branch

Last Answer : Answer: A

In which section of the 24 VDC power supply circuit illustrated, does the greatest change in voltage level take place when fed from ships power. EL-0085 A. I B. II C. III D. IV

Description : In which section of the 24 VDC power supply circuit illustrated, does the greatest change in voltage level take place when fed from ships power. EL-0085 A. I B. II C. III D. IV

Last Answer : Answer: A

How do you eliminate radio frequency variation of an oscillator transmitter caused by its supply voltage? A. Use new power supply B. Lossen power supply shielding C. Use of regulated power supply D. Use of high capacitor in the supply circuit

Description : How do you eliminate radio frequency variation of an oscillator transmitter caused by its supply voltage? A. Use new power supply B. Lossen power supply shielding C. Use of regulated power supply D. Use of high capacitor in the supply circuit

Last Answer : C. Use of regulated power supply

What is the name of the device that provides an increase in current, voltage, or power of a signal without appreciably altering the original signal?

Description : What is the name of the device that provides an increase in current, voltage, or power of a signal without appreciably altering the original signal?

Last Answer : Amplifier.

In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 1 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal ... 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: A

In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

The device labeled 'REG SW' in the illustration is used to ___________. EL-0003 A. shift from the automatic voltage regulator to the manual voltage regulator B. shift the governor control from manual to automatic/zero droop C. enable the operator to read the field voltage on device 'REG ADJ' or device 'MAN ADJ' D. supply regulated control power to the switchboard

Description : The device labeled 'REG SW' in the illustration is used to ___________. EL-0003 A. shift from the automatic voltage regulator to the manual voltage regulator B. shift the governor control from manual to ... device 'REG ADJ' or device 'MAN ADJ' D. supply regulated control power to the switchboard

Last Answer : Answer: A

The voltage control in electric supply networks in required on account of which of the following reasons ? (a) Adjustment of voltage at consumers premises within statutory limits (b) Control of active and reactive power (c) Adjustment of short period daily and seasonal voltage variations in accordance with variations of load (d) All of the above

Description : The voltage control in electric supply networks in required on account of which of the following reasons ? (a) Adjustment of voltage at consumers premises within statutory limits (b) Control of ... daily and seasonal voltage variations in accordance with variations of load (d) All of the above

Last Answer : (d) All of the above