A push pull amplifier balances out A) Odd harmonics B) Even harmonics C) Both odd as well as even harmonics D) Neither odd nor even harmonics.

A push pull amplifier balances out
A) Odd harmonics
B) Even harmonics
C) Both odd as well as even harmonics
D) Neither odd nor even harmonics.
by

1 Answer

Answer :

A) Odd harmonics
by

Related questions

Which of the following contributes to harmonics distortion in amplifiers? A) Positive feedback B) Presence of noise C) Defective active device D) Non linearity in active device.

Description : Which of the following contributes to harmonics distortion in amplifiers? A) Positive feedback B) Presence of noise C) Defective active device D) Non linearity in active device.

Last Answer : D) Non linearity in active device.

The Bandwidth of an RC-coupled amplifier is limited by: A) coupling capacitors at the low frequency end and bypass capacitors at the high frequency end B) coupling capacitors at the high frequency end and bypass capacitors at the low frequency end C) bypass and coupling capacitors at the low frequency end and shunt capacitors at the high frequency end and D) shunt capacitors at the low frequency end and bypass as well as coupling capacitors at the high frequency end.

Description : The Bandwidth of an RC-coupled amplifier is limited by: A) coupling capacitors at the low frequency end and bypass capacitors at the high frequency end B) coupling capacitors at the high frequency ... at the low frequency end and bypass as well as coupling capacitors at the high frequency end.

Last Answer : C) bypass and coupling capacitors at the low frequency end and shunt capacitors at the high frequency end and

As compared to a CB amplifier, a CE amplifier has A) Lower current amplification B) Higher current amplification C) Higher input resistance. D) Both (B) & (C)

Description : As compared to a CB amplifier, a CE amplifier has A) Lower current amplification B) Higher current amplification C) Higher input resistance. D) Both (B) & (C)

Last Answer : D) Both (B) & (C)

In an amplifier if conductor during the cycle is from 0 to 90° and again from 180° to 270°, the amplifier will be termed as A) Class A B) Class B C) Class C D) Class AB.

Description : In an amplifier if conductor during the cycle is from 0 to 90° and again from 180° to 270°, the amplifier will be termed as A) Class A B) Class B C) Class C D) Class AB.

Last Answer : B) Class B

Which of the following methods cannot be used to increase the bandwidth for cascaded RF amplifier stages? A) Wave traps in each stage B) Stagger tuning C) A shunt damping resistor across each tuned circuit D) Doubled tuned transformers with tighter coupling

Description : Which of the following methods cannot be used to increase the bandwidth for cascaded RF amplifier stages? A) Wave traps in each stage B) Stagger tuning C) A shunt damping resistor across each tuned circuit D) Doubled tuned transformers with tighter coupling

Last Answer : A) Wave traps in each stage

Which amplifier will be preferred for highest gain? A) Darlington's pair B) Cascade amplifier C) Cascode amplifier D) Depends on the circuitry

Description : Which amplifier will be preferred for highest gain? A) Darlington's pair B) Cascade amplifier C) Cascode amplifier D) Depends on the circuitry

Last Answer : C) Cascode amplifier

In an amplifier the collector voltage equals the full V+ of 28 V instead of the normal 12 V which of the following can be the trouble? A) RL is open B) Cc is open C) RE is open D) CE is shorted.

Description : In an amplifier the collector voltage equals the full V+ of 28 V instead of the normal 12 V which of the following can be the trouble? A) RL is open B) Cc is open C) RE is open D) CE is shorted.

Last Answer : B) Cc is open

In a resistance loaded amplifier, the gain decreases a high frequencies because A) Of decreasing reactance of the stray CT B) Increasing reactance of the stray CT C) Increasing reactance of CC D) Decreasing reactance of CC.

Description : In a resistance loaded amplifier, the gain decreases a high frequencies because A) Of decreasing reactance of the stray CT B) Increasing reactance of the stray CT C) Increasing reactance of CC D) Decreasing reactance of CC.

Last Answer : D) Decreasing reactance of CC.

An ideal voltage amplifier should have A) Ri = 0, R0 = 0 B) Ri = 0, R0 =∞ C) Ri = ∞, R0 = 0 D) Ri = ∞, R0 = ∞.

Description : An ideal voltage amplifier should have A) Ri = 0, R0 = 0 B) Ri = 0, R0 =∞ C) Ri = ∞, R0 = 0 D) Ri = ∞, R0 = ∞.

Last Answer : C) Ri = ∞, R0 = 0

In a resistance loaded, RC coupled amplifier the dc component is blocked by A) Load resistance RL B) Coupling capacitor, CC C) RB D) The transistor.

Description : In a resistance loaded, RC coupled amplifier the dc component is blocked by A) Load resistance RL B) Coupling capacitor, CC C) RB D) The transistor.

Last Answer : B) Coupling capacitor, CC

If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the input signal C) Need for high dc collector supply D) Clipping of output in the negative half of the input signal

Description : If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the ... for high dc collector supply D) Clipping of output in the negative half of the input signal

Last Answer : B) Clipping of output in the positive half of the input signal

Which of the following circuit would be preferred for a 455 kHz IF amplifier? A) A resistance loaded B) Double tuned transformer C) Video amplifier D) Class C

Description : Which of the following circuit would be preferred for a 455 kHz IF amplifier? A) A resistance loaded B) Double tuned transformer C) Video amplifier D) Class C

Last Answer : B) Double tuned transformer

What conditions are required for an amplifier to oscillate A) There must be feedback B) The feedback must be in phase C) The gain must be greater than the loss D) All the above are regd.

Description : What conditions are required for an amplifier to oscillate A) There must be feedback B) The feedback must be in phase C) The gain must be greater than the loss D) All the above are regd.

Last Answer : B) The feedback must be in phase

Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback

Description : Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback

Last Answer : C) All oscillators generate sine waves

The Darlington pair consists of the following two stages A) CE and CC B) Both C) Both CC D) CE and CB

Description : The Darlington pair consists of the following two stages A) CE and CC B) Both C) Both CC D) CE and CB

Last Answer : C) Both CC

The change in base current will be A) 0.66 micro ampere B) 6.6 micro amperes C) 66 micro amperes D) 660 micro amperes.

Description : The change in base current will be A) 0.66 micro ampere B) 6.6 micro amperes C) 66 micro amperes D) 660 micro amperes.

Last Answer : A) 0.66 micro ampere

Which distortion is least objectionable in case of audio amplifers? A) Phase distortion B) Frequency distortion C) Harmonic distortion D) Inter modulation distortion.

Description : Which distortion is least objectionable in case of audio amplifers? A) Phase distortion B) Frequency distortion C) Harmonic distortion D) Inter modulation distortion.

Last Answer : A) Phase distortion

A IGFET is a A) Linear device B) Square law device C) Half power device D) 3/2 power law device.

Description : A IGFET is a A) Linear device B) Square law device C) Half power device D) 3/2 power law device.

Last Answer : B) Square law device

An FET has a gate source bias of 2 V. The ac input signal is ± 1.2 V. The class of operation is A) A B) B C) C D) AB

Description : An FET has a gate source bias of 2 V. The ac input signal is ± 1.2 V. The class of operation is A) A B) B C) C D) AB

Last Answer : D) AB

Which of the following combinations has no phase inversion of the signal? A) Two CE stages B) CE and CC stages C) Three CE stages D) CE stage and emitter follower.

Description : Which of the following combinations has no phase inversion of the signal? A) Two CE stages B) CE and CC stages C) Three CE stages D) CE stage and emitter follower.

Last Answer : A) Two CE stages

Common base configuration is little used because A) It has low input impedance B) It has high input impedance C) It does not heat up D) It has very high gain.

Description : Common base configuration is little used because A) It has low input impedance B) It has high input impedance C) It does not heat up D) It has very high gain.

Last Answer : A) It has low input impedance

Foldback current limiting has the advantage of A) Better pass transistor protection for long term overloads B) A defined turn on point C) Circuit simplicity D) All of the above.

Description : Foldback current limiting has the advantage of A) Better pass transistor protection for long term overloads B) A defined turn on point C) Circuit simplicity D) All of the above.

Last Answer : A) Better pass transistor protection for long term overloads

A crow bar is a power supply circuit that provides A) Conventional current limiting B) Foldback current. limiting C) Temperature control D) Voltage limiting.

Description : A crow bar is a power supply circuit that provides A) Conventional current limiting B) Foldback current. limiting C) Temperature control D) Voltage limiting.

Last Answer : D) Voltage limiting.

Current limited power supplies can prevent damage to A) Rectifier diodes and power transformers. B) Pass transistors C) Other circuits in the system D) All of the above.

Description : Current limited power supplies can prevent damage to A) Rectifier diodes and power transformers. B) Pass transistors C) Other circuits in the system D) All of the above.

Last Answer : D) All of the above.

In general, MOV devices are used to protect electronic equipment from dangerous operating conditions such as A) High temperatures B) Line transients C) Over current D) All of the above.

Description : In general, MOV devices are used to protect electronic equipment from dangerous operating conditions such as A) High temperatures B) Line transients C) Over current D) All of the above.

Last Answer : D) All of the above.

Load regulation is a measure of a power supplies ability keep a constant output under conditions of changing A) Line voltage B) Current demand C) Temperature D) Oscillator frequency.

Description : Load regulation is a measure of a power supplies ability keep a constant output under conditions of changing A) Line voltage B) Current demand C) Temperature D) Oscillator frequency.

Last Answer : A) Line voltage

What is the phase relationship of the signal at the collector of Q2 to the signal at the collector of Q, A) 0° B) 90° C) 180° D) 360°.

Description : What is the phase relationship of the signal at the collector of Q2 to the signal at the collector of Q, A) 0° B) 90° C) 180° D) 360°.

Last Answer : C) 180°

A series mode crystal is marked 10.000 MHz., It is used in a circuit that operates the crystal in its parallel mode. The circuit can be expected to A) Run below 10 MHz B) Run at 10 MHz C) Run above 10 MHz D) Not oscillate.

Description : A series mode crystal is marked 10.000 MHz., It is used in a circuit that operates the crystal in its parallel mode. The circuit can be expected to A) Run below 10 MHz B) Run at 10 MHz C) Run above 10 MHz D) Not oscillate.

Last Answer : C) Run above 10 MHz

Six (6) MHz crystal oscillator has a stability of 1 part in 106. The largest frequency error expected of this crystals A) 0.06 Hz B) 0.6 Hz C) 6 Hz D) 60 Hz.

Description : Six (6) MHz crystal oscillator has a stability of 1 part in 106. The largest frequency error expected of this crystals A) 0.06 Hz B) 0.6 Hz C) 6 Hz D) 60 Hz.

Last Answer : C) 6 Hz

An oscillator that uses crystal control should be A) Frequency stable B) useful only at low frequencies C) AVFO D) none of the above.

Description : An oscillator that uses crystal control should be A) Frequency stable B) useful only at low frequencies C) AVFO D) none of the above.

Last Answer : A) Frequency stable

The major function of transistor. Q2 is A) It provides voltage gain B) It provides the feedback signal C) It isolates the oscillator from loading effects D) It provides a phase shift.

Description : The major function of transistor. Q2 is A) It provides voltage gain B) It provides the feedback signal C) It isolates the oscillator from loading effects D) It provides a phase shift.

Last Answer : ) It provides a phase shift.

The ideal characteristic of a voltage stablizer is A) constant output voltage with low internal resistance B) constant output current with low internal resistance C) constant output voltage with high internal resistance D) constant internal resistance with variable output voltage.

Description : The ideal characteristic of a voltage stablizer is A) constant output voltage with low internal resistance B) constant output current with low internal resistance C) constant output voltage with high internal resistance D) constant internal resistance with variable output voltage.

Last Answer : A) constant output voltage with low internal resistance

Draw the circuit diagram of complementary symmetry Class B push-pull amplifier and describe its working.

Description : Draw the circuit diagram of complementary symmetry Class B push-pull amplifier and describe its working.

Last Answer : Diagram of complementary symmetry Class B push-pull amplifier: Working: The above circuit employs a NPN transistor and a PNP transistor connected in push pull configuration. When the input ... of class B, this circuit is termed as Complementary symmetry push pull class B amplifier.

Draw the circuit of complementary, symmetry push pull amplifier and explain its working.

Description : Draw the circuit of complementary, symmetry push pull amplifier and explain its working.

Last Answer : COMPLEMENTRY SYMMETRY CLASS B PUSH PULL AMPLIFIER  Circuit Diagram:  Circuit description: * Two transistors one NPN & other PNP is used in the circuit so they are complementary to each other. ... conducts & NPN remains OFF.  So we get remaining half cycle in the output.

Explain with circuit diagram and waveform the operation of class AB push pull power amplifier.

Description : Explain with circuit diagram and waveform the operation of class AB push pull power amplifier.

Last Answer : Class AB Push Pull Power Amplifier:  Circuit Diagram:  Circuit Decription: The circuit consists of two centre-tapped transformers T1 and T2, two identical transistors Q1 and Q2 , Resistor R and ... two halves & produces a full sine wave in the load resistor. Waveform :

working of class B push pull amplifier.

Description : working of class B push pull amplifier.

Last Answer : Circuit Diagram:- Operation:  In class B amplifier transistor conduct only for half cycle of input signal.One conduct in positive half cycle and other conducts in negative half ... Then output transformer joins these two halves and produces a full sine wave in the load resistor. 

Draw diagram of class A push-pull amplifier and explain its operation.

Description : Draw diagram of class A push-pull amplifier and explain its operation. 

Last Answer : Class A Push-pull Amplifier: The circuit diagram of class A push-pull amplifier is as shown in the fig.(a). Operation: The resistors R1 and R2 along with Vcc provide the dc biasing so as ... Vcc is applied to the collectors of transistors Q1 and Q2 through the centretapped output transformer. 

The efficiency of a class B push-pull amplifier is

Description : The efficiency of a class B push-pull amplifier is

Last Answer : The efficiency of a class B push-pull amplifier is 75-80%

When large amount of power is required, a push pull amplifier is designed for operation as

Last Answer : When large amount of power is required, a push pull amplifier is designed for operation as class B.

Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Description : Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Last Answer : D. To prevent re-radiation of the local oscillator

One ofthe followingis not a reason forthe use of anantenna coupler: a. To make the antenna look resistive b. To provide the output amplifier with the correct load impedance c. To discriminate against harmonics d. To prevent reradiation of the local oscillator

Description : One ofthe followingis not a reason forthe use of anantenna coupler: a. To make the antenna look resistive b. To provide the output amplifier with the correct load impedance c. To discriminate against harmonics d. To prevent reradiation of the local oscillator

Last Answer : d. To prevent reradiation of the local oscillator

Stacking antenna elements A. increases sensitivity to weak signals B. will suppress odd harmonics C. decrease signal to noise ratio D. increases selectivity

Description : Stacking antenna elements A. increases sensitivity to weak signals B. will suppress odd harmonics C. decrease signal to noise ratio D. increases selectivity

Last Answer : A. increases sensitivity to weak signals

If the two input signals to a difference amplifier are equal in amplitude but neither in phase nor 180 degrees out of phase, what will the output signal be?

Description : If the two input signals to a difference amplifier are equal in amplitude but neither in phase nor 180 degrees out of phase, what will the output signal be?

Last Answer : . A different shape than the input signals but larger in amplitude.

39JIT is a a)Push system b)Pull system c)Both d) None of these

Description : 39JIT is a a)Push system b)Pull system c)Both d) None of these

Last Answer : b)Pull system

JIT is a a. Push system b. Pull system c. Both d. None of these

Description : JIT is a a. Push system b. Pull system c. Both d. None of these

Last Answer : b. Pull system

What are three possible causes of even-order harmonics?

Description : What are three possible causes of even-order harmonics?

Last Answer : a. Permanently magnetized heads. b. Faulty circuitry. c. Asymmetrical bias signal.

Consider the following statements: 1. Chikmagalur is well-known for sugar production. 2. Mandya is well-known as a coffee-producing region. Which of the statements given above is/are correct? [IAS 2008] (a) 1 only (b) 2 only (c) Both 1and 2 (d) Neither 1 nor 2

Description : Consider the following statements: 1. Chikmagalur is well-known for sugar production. 2. Mandya is well-known as a coffee-producing region. Which of the statements given above is/are correct? [IAS 2008] (a) 1 only (b) 2 only (c) Both 1and 2 (d) Neither 1 nor 2

Last Answer : Ans: (d)

Where can I purchase a Weslo Cardio Glide new or used exercise machine, with seat, handlebar and pedals I don't want a treadmill. The seat rises as you push your legs out, feet on the pedals, pull the handle bar towards you. What is approximate price?

Description : Where can I purchase a Weslo Cardio Glide new or used exercise machine, with seat, handlebar and pedals I don't want a treadmill. The seat rises as you push your legs out, feet on the pedals, pull the handle bar towards you. What is approximate price?

Last Answer : The Weslo Cardio Glide machine is difficult to find new however there is one etailer that still carries it, www.ranchomurieta.com. It may be easier however to simply purchase another machine with the ... as Craigslist.org where you can occasionally find the Weslo Cardio Glide for around $20 - $40.

The law of Pull & Push of Web Marketing refers to 1. Pull people to your site, then push quality information to them 2. Pull people to your site and force them to purchase 3. Pull people to your site and Push them away 4. Pull the money of people and push them out 5. None of these

Description : The law of Pull & Push of Web Marketing refers to 1. Pull people to your site, then push quality information to them 2. Pull people to your site and force them to purchase 3. Pull people to your site and Push them away 4. Pull the money of people and push them out 5. None of these

Last Answer : Pull people to your site, then push quality information to them

In the question given below, there are two statements followed by two conclusions. You have to take the given statements to be true even if they seem to be at variance from commonly known facts. Read all the conclusions, and then decide which of the given conclusions logically follows from the given statements? St at ement s: Some kings are queens All the queens are beautiful. Conclusi ons: I . All the kings are beautiful I I . All the queens are kings. (1) Only I follows (2) Only II follows (3) Neither I nor II follows

Description : In the question given below, there are two statements followed by two conclusions. You have to take the given statements to be true even if they seem to be at variance from commonly known facts. Read all the ... queens are kings. (1) Only I follows (2) Only II follows (3) Neither I nor II follows

Last Answer : (3) Neither I nor II follows