Which of the following circuit would be preferred for a 455 kHz IF amplifier? A) A resistance loaded B) Double tuned transformer C) Video amplifier D) Class C

Which of the following circuit would be preferred for a 455 kHz IF amplifier?
A) A resistance loaded
B) Double tuned transformer
C) Video amplifier
D) Class C
by

1 Answer

Answer :

B) Double tuned transformer
by

Related questions

Which of the following methods cannot be used to increase the bandwidth for cascaded RF amplifier stages? A) Wave traps in each stage B) Stagger tuning C) A shunt damping resistor across each tuned circuit D) Doubled tuned transformers with tighter coupling

Description : Which of the following methods cannot be used to increase the bandwidth for cascaded RF amplifier stages? A) Wave traps in each stage B) Stagger tuning C) A shunt damping resistor across each tuned circuit D) Doubled tuned transformers with tighter coupling

Last Answer : A) Wave traps in each stage

In a resistance loaded amplifier, the gain decreases a high frequencies because A) Of decreasing reactance of the stray CT B) Increasing reactance of the stray CT C) Increasing reactance of CC D) Decreasing reactance of CC.

Description : In a resistance loaded amplifier, the gain decreases a high frequencies because A) Of decreasing reactance of the stray CT B) Increasing reactance of the stray CT C) Increasing reactance of CC D) Decreasing reactance of CC.

Last Answer : D) Decreasing reactance of CC.

In a resistance loaded, RC coupled amplifier the dc component is blocked by A) Load resistance RL B) Coupling capacitor, CC C) RB D) The transistor.

Description : In a resistance loaded, RC coupled amplifier the dc component is blocked by A) Load resistance RL B) Coupling capacitor, CC C) RB D) The transistor.

Last Answer : B) Coupling capacitor, CC

Which amplifier will be preferred for highest gain? A) Darlington's pair B) Cascade amplifier C) Cascode amplifier D) Depends on the circuitry

Description : Which amplifier will be preferred for highest gain? A) Darlington's pair B) Cascade amplifier C) Cascode amplifier D) Depends on the circuitry

Last Answer : C) Cascode amplifier

A superhet receiver has an IF of 455 kHz and is experiencing image-channel interference on a frequency of 1570 kHz. The receiver is tuned to A. 1115 kHz B. 660 kHz C. 2025 kHz D. 910 kHz

Description : A superhet receiver has an IF of 455 kHz and is experiencing image-channel interference on a frequency of 1570 kHz. The receiver is tuned to A. 1115 kHz B. 660 kHz C. 2025 kHz D. 910 kHz

Last Answer : B. 660 kHz

As compared to a CB amplifier, a CE amplifier has A) Lower current amplification B) Higher current amplification C) Higher input resistance. D) Both (B) & (C)

Description : As compared to a CB amplifier, a CE amplifier has A) Lower current amplification B) Higher current amplification C) Higher input resistance. D) Both (B) & (C)

Last Answer : D) Both (B) & (C)

Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback

Description : Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback

Last Answer : C) All oscillators generate sine waves

In an amplifier if conductor during the cycle is from 0 to 90° and again from 180° to 270°, the amplifier will be termed as A) Class A B) Class B C) Class C D) Class AB.

Description : In an amplifier if conductor during the cycle is from 0 to 90° and again from 180° to 270°, the amplifier will be termed as A) Class A B) Class B C) Class C D) Class AB.

Last Answer : B) Class B

A push pull amplifier balances out A) Odd harmonics B) Even harmonics C) Both odd as well as even harmonics D) Neither odd nor even harmonics.

Description : A push pull amplifier balances out A) Odd harmonics B) Even harmonics C) Both odd as well as even harmonics D) Neither odd nor even harmonics.

Last Answer : A) Odd harmonics

In an amplifier the collector voltage equals the full V+ of 28 V instead of the normal 12 V which of the following can be the trouble? A) RL is open B) Cc is open C) RE is open D) CE is shorted.

Description : In an amplifier the collector voltage equals the full V+ of 28 V instead of the normal 12 V which of the following can be the trouble? A) RL is open B) Cc is open C) RE is open D) CE is shorted.

Last Answer : B) Cc is open

An ideal voltage amplifier should have A) Ri = 0, R0 = 0 B) Ri = 0, R0 =∞ C) Ri = ∞, R0 = 0 D) Ri = ∞, R0 = ∞.

Description : An ideal voltage amplifier should have A) Ri = 0, R0 = 0 B) Ri = 0, R0 =∞ C) Ri = ∞, R0 = 0 D) Ri = ∞, R0 = ∞.

Last Answer : C) Ri = ∞, R0 = 0

If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the input signal C) Need for high dc collector supply D) Clipping of output in the negative half of the input signal

Description : If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the ... for high dc collector supply D) Clipping of output in the negative half of the input signal

Last Answer : B) Clipping of output in the positive half of the input signal

What conditions are required for an amplifier to oscillate A) There must be feedback B) The feedback must be in phase C) The gain must be greater than the loss D) All the above are regd.

Description : What conditions are required for an amplifier to oscillate A) There must be feedback B) The feedback must be in phase C) The gain must be greater than the loss D) All the above are regd.

Last Answer : B) The feedback must be in phase

The Bandwidth of an RC-coupled amplifier is limited by: A) coupling capacitors at the low frequency end and bypass capacitors at the high frequency end B) coupling capacitors at the high frequency end and bypass capacitors at the low frequency end C) bypass and coupling capacitors at the low frequency end and shunt capacitors at the high frequency end and D) shunt capacitors at the low frequency end and bypass as well as coupling capacitors at the high frequency end.

Description : The Bandwidth of an RC-coupled amplifier is limited by: A) coupling capacitors at the low frequency end and bypass capacitors at the high frequency end B) coupling capacitors at the high frequency ... at the low frequency end and bypass as well as coupling capacitors at the high frequency end.

Last Answer : C) bypass and coupling capacitors at the low frequency end and shunt capacitors at the high frequency end and

An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Description : An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Last Answer : B. 4.0 µV

The ideal characteristic of a voltage stablizer is A) constant output voltage with low internal resistance B) constant output current with low internal resistance C) constant output voltage with high internal resistance D) constant internal resistance with variable output voltage.

Description : The ideal characteristic of a voltage stablizer is A) constant output voltage with low internal resistance B) constant output current with low internal resistance C) constant output voltage with high internal resistance D) constant internal resistance with variable output voltage.

Last Answer : A) constant output voltage with low internal resistance

Foldback current limiting has the advantage of A) Better pass transistor protection for long term overloads B) A defined turn on point C) Circuit simplicity D) All of the above.

Description : Foldback current limiting has the advantage of A) Better pass transistor protection for long term overloads B) A defined turn on point C) Circuit simplicity D) All of the above.

Last Answer : A) Better pass transistor protection for long term overloads

A crow bar is a power supply circuit that provides A) Conventional current limiting B) Foldback current. limiting C) Temperature control D) Voltage limiting.

Description : A crow bar is a power supply circuit that provides A) Conventional current limiting B) Foldback current. limiting C) Temperature control D) Voltage limiting.

Last Answer : D) Voltage limiting.

A series mode crystal is marked 10.000 MHz., It is used in a circuit that operates the crystal in its parallel mode. The circuit can be expected to A) Run below 10 MHz B) Run at 10 MHz C) Run above 10 MHz D) Not oscillate.

Description : A series mode crystal is marked 10.000 MHz., It is used in a circuit that operates the crystal in its parallel mode. The circuit can be expected to A) Run below 10 MHz B) Run at 10 MHz C) Run above 10 MHz D) Not oscillate.

Last Answer : C) Run above 10 MHz

An FET has a gate source bias of 2 V. The ac input signal is ± 1.2 V. The class of operation is A) A B) B C) C D) AB

Description : An FET has a gate source bias of 2 V. The ac input signal is ± 1.2 V. The class of operation is A) A B) B C) C D) AB

Last Answer : D) AB

Describe the operation of double tuned amplifier with the help of neat circuit diagram and mention its applications.

Description : Describe the operation of double tuned amplifier with the help of neat circuit diagram and mention its applications.

Last Answer : Circuit diagram: Operation:  *The signal to be amplified is applied at the input terminal through the coupling capacitor CC  *The resonant frequency of the tuned circuit L1 C1 is made equal ... : (i) Radio and T .V broadcasting as tuning circuit. (ii) Wireless communication system.

A tuned circuit has a Q of 100 at its resonant frequency of 500 kHz. Its bandwidth is _____kHz.

Description : A tuned circuit has a Q of 100 at its resonant frequency of 500 kHz. Its bandwidth is _____kHz. (A) 50000 (B) 0.2 (C) 600 (D) 5

Last Answer : A tuned circuit has a Q of 100 at its resonant frequency of 500 kHz. Its bandwidth is 5 kHz.

The change in base current will be A) 0.66 micro ampere B) 6.6 micro amperes C) 66 micro amperes D) 660 micro amperes.

Description : The change in base current will be A) 0.66 micro ampere B) 6.6 micro amperes C) 66 micro amperes D) 660 micro amperes.

Last Answer : A) 0.66 micro ampere

Which distortion is least objectionable in case of audio amplifers? A) Phase distortion B) Frequency distortion C) Harmonic distortion D) Inter modulation distortion.

Description : Which distortion is least objectionable in case of audio amplifers? A) Phase distortion B) Frequency distortion C) Harmonic distortion D) Inter modulation distortion.

Last Answer : A) Phase distortion

Which of the following contributes to harmonics distortion in amplifiers? A) Positive feedback B) Presence of noise C) Defective active device D) Non linearity in active device.

Description : Which of the following contributes to harmonics distortion in amplifiers? A) Positive feedback B) Presence of noise C) Defective active device D) Non linearity in active device.

Last Answer : D) Non linearity in active device.

A IGFET is a A) Linear device B) Square law device C) Half power device D) 3/2 power law device.

Description : A IGFET is a A) Linear device B) Square law device C) Half power device D) 3/2 power law device.

Last Answer : B) Square law device

Which of the following combinations has no phase inversion of the signal? A) Two CE stages B) CE and CC stages C) Three CE stages D) CE stage and emitter follower.

Description : Which of the following combinations has no phase inversion of the signal? A) Two CE stages B) CE and CC stages C) Three CE stages D) CE stage and emitter follower.

Last Answer : A) Two CE stages

The Darlington pair consists of the following two stages A) CE and CC B) Both C) Both CC D) CE and CB

Description : The Darlington pair consists of the following two stages A) CE and CC B) Both C) Both CC D) CE and CB

Last Answer : C) Both CC

Common base configuration is little used because A) It has low input impedance B) It has high input impedance C) It does not heat up D) It has very high gain.

Description : Common base configuration is little used because A) It has low input impedance B) It has high input impedance C) It does not heat up D) It has very high gain.

Last Answer : A) It has low input impedance

Current limited power supplies can prevent damage to A) Rectifier diodes and power transformers. B) Pass transistors C) Other circuits in the system D) All of the above.

Description : Current limited power supplies can prevent damage to A) Rectifier diodes and power transformers. B) Pass transistors C) Other circuits in the system D) All of the above.

Last Answer : D) All of the above.

In general, MOV devices are used to protect electronic equipment from dangerous operating conditions such as A) High temperatures B) Line transients C) Over current D) All of the above.

Description : In general, MOV devices are used to protect electronic equipment from dangerous operating conditions such as A) High temperatures B) Line transients C) Over current D) All of the above.

Last Answer : D) All of the above.

Load regulation is a measure of a power supplies ability keep a constant output under conditions of changing A) Line voltage B) Current demand C) Temperature D) Oscillator frequency.

Description : Load regulation is a measure of a power supplies ability keep a constant output under conditions of changing A) Line voltage B) Current demand C) Temperature D) Oscillator frequency.

Last Answer : A) Line voltage

What is the phase relationship of the signal at the collector of Q2 to the signal at the collector of Q, A) 0° B) 90° C) 180° D) 360°.

Description : What is the phase relationship of the signal at the collector of Q2 to the signal at the collector of Q, A) 0° B) 90° C) 180° D) 360°.

Last Answer : C) 180°

Six (6) MHz crystal oscillator has a stability of 1 part in 106. The largest frequency error expected of this crystals A) 0.06 Hz B) 0.6 Hz C) 6 Hz D) 60 Hz.

Description : Six (6) MHz crystal oscillator has a stability of 1 part in 106. The largest frequency error expected of this crystals A) 0.06 Hz B) 0.6 Hz C) 6 Hz D) 60 Hz.

Last Answer : C) 6 Hz

An oscillator that uses crystal control should be A) Frequency stable B) useful only at low frequencies C) AVFO D) none of the above.

Description : An oscillator that uses crystal control should be A) Frequency stable B) useful only at low frequencies C) AVFO D) none of the above.

Last Answer : A) Frequency stable

The major function of transistor. Q2 is A) It provides voltage gain B) It provides the feedback signal C) It isolates the oscillator from loading effects D) It provides a phase shift.

Description : The major function of transistor. Q2 is A) It provides voltage gain B) It provides the feedback signal C) It isolates the oscillator from loading effects D) It provides a phase shift.

Last Answer : ) It provides a phase shift.

What is the local oscillator frequency range commercial AM broadcast if it is equal to 455 KHz. A. 540 to 1600 KHz B. 0 to 1600 KHz C. 995 to 2055 KHz D. 0 to 455 KHz

Description : What is the local oscillator frequency range commercial AM broadcast if it is equal to 455 KHz. A. 540 to 1600 KHz B. 0 to 1600 KHz C. 995 to 2055 KHz D. 0 to 455 KHz

Last Answer : C. 995 to 2055 KHz

Draw the circuit of single tuned amplifier and state its operating principle.

Description : Draw the circuit of single tuned amplifier and state its operating principle.

Last Answer : Operating Principle: The working of tuned voltage amplifier may be understood by considering a radio frequency signal, to be amplified applied at the input of the amplifier. The resonant frequency ... will be amplified. And all the other frequencies will be rejected by the tuned circuit. 

role of tuned LC circuit in tuned amplifier.

Description : role of tuned LC circuit in tuned amplifier.

Last Answer : In order to pick up and amplify the desired radio frequency signal, the resistive load in the audio amplifier is replaced by a tuned circuit (also called a parallel resonant circuit)as shown ... desired radio frequency signal. (ii)Amplification of the selected signal to a suitable voltage level.

A super heterodyne AM receiver is tuned to a station operating at 1200 KHz .Find local oscillator frequency and image frequency.

Description : A super heterodyne AM receiver is tuned to a station operating at 1200 KHz .Find local oscillator frequency and image frequency.

Last Answer : A super heterodyne AM receiver is tuned to a station operating at 1200 KHz Intermediate frequency is 455KHz. IF frequency=f0-fs Local oscillator frequency is f0=IF +fs=455K+1200K=1655kHz The image frequency which gives the same IF is f0+2*IF=2110KHz

The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an autotransformer B. operational amplifier whose output controls a step-up voltage reactor C. amplitude modulator whose output drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor

Description : The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an ... drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor

Last Answer : Answer: D

Give the classification of tuned amplifier

Description : Give the classification of tuned amplifier

Last Answer : (i) Small signal tuned amplifier *Single tuned *Double tuned *Stagger tuned (ii) Large signal tuned amplifier.

What is the need for a tuned amplifier?

Description : What is the need for a tuned amplifier?

Last Answer : In radio or TV receivers , it is necessary to select a particular channel among all other available channels.Hence some sort of frequency selective circuit is needed that will allow us to amplify ... and reject all the other unwanted signals and this function is provided by a tuned amplifier.

Sketch the single tuned amplifier.

Description : Sketch the single tuned amplifier.

Last Answer : single tuned amplifier

Explain stagger tuned amplifier with the help of waveforms.

Description : Explain stagger tuned amplifier with the help of waveforms.

Last Answer : Circuit Diagram: Above figure shows two-stage tuned voltage amplifier. The stagger tuning in this circuit, may be achieved by resonating the tuned circuits L1C1 and L2C2 to slightly different ... outside the pass-band. Because of the stagger tuning there is a loss of voltage gain.

State the need of tuned amplifier in electronic circuits.

Description : State the need of tuned amplifier in electronic circuits.

Last Answer : Necessity of tuned amplifier: 1. Selection of the desired radio frequency signal. 2. Amplification of the selected signal to a selected voltage level.

The noise output of a resistor is amplified by a noiseless amplifier having a gain of 60 and a bandwidth of 20 kHz. A meter connected at the output of the amplifier reads 1mV RMS. If the bandwidth of the amplifier is reduced to 5kHz, its gain remaining constant, what does the meter read now? A. 0.5 mV B. 0.5 µV C. 5.0 mV D. 5.0 µV

Description : The noise output of a resistor is amplified by a noiseless amplifier having a gain of 60 and a bandwidth of 20 kHz. A meter connected at the output of the amplifier reads 1mV RMS. If the bandwidth of the amplifier is reduced to ... does the meter read now? A. 0.5 mV B. 0.5 µV C. 5.0 mV D. 5.0 µV

Last Answer : A. 0.5 mV

Consider the following statements : If a high Q parallel resonant circuit is loaded with a resistance ...

Description : Consider the following statements : If a high Q parallel resonant circuit is loaded with a resistance  1. The circuit impedance reduces.  2. The resonant frequency remains the same.  3. The bandwidth reduces.  Which of the above statements is/are correct ?

Last Answer : 1

In the illustrated electronic governor, the circuit card connected to the potential and current transformers is for ________. EL-0046 A. increasing the signal strength to the governor to maintain constant engine speed with increased load B. send a kilowatt signal to the metering circuit C. shutting down the prime mover in the event of reverse power to protect from motorization D. conditioning the load through the use of a magnetic amplifier current transformer

Description : In the illustrated electronic governor, the circuit card connected to the potential and current transformers is for ________. EL-0046 A. increasing the signal strength to the governor to ... from motorization D. conditioning the load through the use of a magnetic amplifier current transformer

Last Answer : Answer: A

What can be used to replace the exciter in the circuit shown in the illustration? EL-0101 A. A step-up transformer. B. A rectifier. C. A step-down transformer. D. An operational amplifier.

Description : What can be used to replace the exciter in the circuit shown in the illustration? EL-0101 A. A step-up transformer. B. A rectifier. C. A step-down transformer. D. An operational amplifier.

Last Answer : Answer: B