Which of the following combinations has no phase inversion of the signal? A) Two CE stages B) CE and CC stages C) Three CE stages D) CE stage and emitter follower.

Question

Which of the following combinations has no phase inversion of the signal? A) Two CE stages B) CE and CC stages C) Three CE stages D) CE stage and emitter follower.

Which of the following combinations has no phase inversion of the signal?
A) Two CE stages
B) CE and CC stages
C) Three CE stages
D) CE stage and emitter follower.

asked Aug 21, 2021 by anonymous

1 Answer

Related questions

The Darlington pair consists of the following two stages A) CE and CC B) Both C) Both CC D) CE and CB

Description : The Darlington pair consists of the following two stages A) CE and CC B) Both C) Both CC D) CE and CB

Last Answer : C) Both CC

In an amplifier the collector voltage equals the full V+ of 28 V instead of the normal 12 V which of the following can be the trouble? A) RL is open B) Cc is open C) RE is open D) CE is shorted.

Description : In an amplifier the collector voltage equals the full V+ of 28 V instead of the normal 12 V which of the following can be the trouble? A) RL is open B) Cc is open C) RE is open D) CE is shorted.

Last Answer : B) Cc is open

Which of the following methods cannot be used to increase the bandwidth for cascaded RF amplifier stages? A) Wave traps in each stage B) Stagger tuning C) A shunt damping resistor across each tuned circuit D) Doubled tuned transformers with tighter coupling

Description : Which of the following methods cannot be used to increase the bandwidth for cascaded RF amplifier stages? A) Wave traps in each stage B) Stagger tuning C) A shunt damping resistor across each tuned circuit D) Doubled tuned transformers with tighter coupling

Last Answer : A) Wave traps in each stage

As compared to a CB amplifier, a CE amplifier has A) Lower current amplification B) Higher current amplification C) Higher input resistance. D) Both (B) & (C)

Description : As compared to a CB amplifier, a CE amplifier has A) Lower current amplification B) Higher current amplification C) Higher input resistance. D) Both (B) & (C)

Last Answer : D) Both (B) & (C)

In a resistance loaded amplifier, the gain decreases a high frequencies because A) Of decreasing reactance of the stray CT B) Increasing reactance of the stray CT C) Increasing reactance of CC D) Decreasing reactance of CC.

Description : In a resistance loaded amplifier, the gain decreases a high frequencies because A) Of decreasing reactance of the stray CT B) Increasing reactance of the stray CT C) Increasing reactance of CC D) Decreasing reactance of CC.

Last Answer : D) Decreasing reactance of CC.

In a resistance loaded, RC coupled amplifier the dc component is blocked by A) Load resistance RL B) Coupling capacitor, CC C) RB D) The transistor.

Description : In a resistance loaded, RC coupled amplifier the dc component is blocked by A) Load resistance RL B) Coupling capacitor, CC C) RB D) The transistor.

Last Answer : B) Coupling capacitor, CC

What is the phase relationship of the signal at the collector of Q2 to the signal at the collector of Q, A) 0° B) 90° C) 180° D) 360°.

Description : What is the phase relationship of the signal at the collector of Q2 to the signal at the collector of Q, A) 0° B) 90° C) 180° D) 360°.

Last Answer : C) 180°

The major function of transistor. Q2 is A) It provides voltage gain B) It provides the feedback signal C) It isolates the oscillator from loading effects D) It provides a phase shift.

Description : The major function of transistor. Q2 is A) It provides voltage gain B) It provides the feedback signal C) It isolates the oscillator from loading effects D) It provides a phase shift.

Last Answer : ) It provides a phase shift.

Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback

Description : Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback

Last Answer : C) All oscillators generate sine waves

An FET has a gate source bias of 2 V. The ac input signal is ± 1.2 V. The class of operation is A) A B) B C) C D) AB

Description : An FET has a gate source bias of 2 V. The ac input signal is ± 1.2 V. The class of operation is A) A B) B C) C D) AB

Last Answer : D) AB

If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the input signal C) Need for high dc collector supply D) Clipping of output in the negative half of the input signal

Description : If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the ... for high dc collector supply D) Clipping of output in the negative half of the input signal

Last Answer : B) Clipping of output in the positive half of the input signal

Which distortion is least objectionable in case of audio amplifers? A) Phase distortion B) Frequency distortion C) Harmonic distortion D) Inter modulation distortion.

Description : Which distortion is least objectionable in case of audio amplifers? A) Phase distortion B) Frequency distortion C) Harmonic distortion D) Inter modulation distortion.

Last Answer : A) Phase distortion

What conditions are required for an amplifier to oscillate A) There must be feedback B) The feedback must be in phase C) The gain must be greater than the loss D) All the above are regd.

Description : What conditions are required for an amplifier to oscillate A) There must be feedback B) The feedback must be in phase C) The gain must be greater than the loss D) All the above are regd.

Last Answer : B) The feedback must be in phase

The change in base current will be A) 0.66 micro ampere B) 6.6 micro amperes C) 66 micro amperes D) 660 micro amperes.

Description : The change in base current will be A) 0.66 micro ampere B) 6.6 micro amperes C) 66 micro amperes D) 660 micro amperes.

Last Answer : A) 0.66 micro ampere

In an amplifier if conductor during the cycle is from 0 to 90° and again from 180° to 270°, the amplifier will be termed as A) Class A B) Class B C) Class C D) Class AB.

Description : In an amplifier if conductor during the cycle is from 0 to 90° and again from 180° to 270°, the amplifier will be termed as A) Class A B) Class B C) Class C D) Class AB.

Last Answer : B) Class B

A push pull amplifier balances out A) Odd harmonics B) Even harmonics C) Both odd as well as even harmonics D) Neither odd nor even harmonics.

Description : A push pull amplifier balances out A) Odd harmonics B) Even harmonics C) Both odd as well as even harmonics D) Neither odd nor even harmonics.

Last Answer : A) Odd harmonics

Which amplifier will be preferred for highest gain? A) Darlington's pair B) Cascade amplifier C) Cascode amplifier D) Depends on the circuitry

Description : Which amplifier will be preferred for highest gain? A) Darlington's pair B) Cascade amplifier C) Cascode amplifier D) Depends on the circuitry

Last Answer : C) Cascode amplifier

Which of the following contributes to harmonics distortion in amplifiers? A) Positive feedback B) Presence of noise C) Defective active device D) Non linearity in active device.

Description : Which of the following contributes to harmonics distortion in amplifiers? A) Positive feedback B) Presence of noise C) Defective active device D) Non linearity in active device.

Last Answer : D) Non linearity in active device.

An ideal voltage amplifier should have A) Ri = 0, R0 = 0 B) Ri = 0, R0 =∞ C) Ri = ∞, R0 = 0 D) Ri = ∞, R0 = ∞.

Description : An ideal voltage amplifier should have A) Ri = 0, R0 = 0 B) Ri = 0, R0 =∞ C) Ri = ∞, R0 = 0 D) Ri = ∞, R0 = ∞.

Last Answer : C) Ri = ∞, R0 = 0

A IGFET is a A) Linear device B) Square law device C) Half power device D) 3/2 power law device.

Description : A IGFET is a A) Linear device B) Square law device C) Half power device D) 3/2 power law device.

Last Answer : B) Square law device

Which of the following circuit would be preferred for a 455 kHz IF amplifier? A) A resistance loaded B) Double tuned transformer C) Video amplifier D) Class C

Description : Which of the following circuit would be preferred for a 455 kHz IF amplifier? A) A resistance loaded B) Double tuned transformer C) Video amplifier D) Class C

Last Answer : B) Double tuned transformer

Common base configuration is little used because A) It has low input impedance B) It has high input impedance C) It does not heat up D) It has very high gain.

Description : Common base configuration is little used because A) It has low input impedance B) It has high input impedance C) It does not heat up D) It has very high gain.

Last Answer : A) It has low input impedance

Foldback current limiting has the advantage of A) Better pass transistor protection for long term overloads B) A defined turn on point C) Circuit simplicity D) All of the above.

Description : Foldback current limiting has the advantage of A) Better pass transistor protection for long term overloads B) A defined turn on point C) Circuit simplicity D) All of the above.

Last Answer : A) Better pass transistor protection for long term overloads

A crow bar is a power supply circuit that provides A) Conventional current limiting B) Foldback current. limiting C) Temperature control D) Voltage limiting.

Description : A crow bar is a power supply circuit that provides A) Conventional current limiting B) Foldback current. limiting C) Temperature control D) Voltage limiting.

Last Answer : D) Voltage limiting.

Current limited power supplies can prevent damage to A) Rectifier diodes and power transformers. B) Pass transistors C) Other circuits in the system D) All of the above.

Description : Current limited power supplies can prevent damage to A) Rectifier diodes and power transformers. B) Pass transistors C) Other circuits in the system D) All of the above.

Last Answer : D) All of the above.

In general, MOV devices are used to protect electronic equipment from dangerous operating conditions such as A) High temperatures B) Line transients C) Over current D) All of the above.

Description : In general, MOV devices are used to protect electronic equipment from dangerous operating conditions such as A) High temperatures B) Line transients C) Over current D) All of the above.

Last Answer : D) All of the above.

Load regulation is a measure of a power supplies ability keep a constant output under conditions of changing A) Line voltage B) Current demand C) Temperature D) Oscillator frequency.

Description : Load regulation is a measure of a power supplies ability keep a constant output under conditions of changing A) Line voltage B) Current demand C) Temperature D) Oscillator frequency.

Last Answer : A) Line voltage

A series mode crystal is marked 10.000 MHz., It is used in a circuit that operates the crystal in its parallel mode. The circuit can be expected to A) Run below 10 MHz B) Run at 10 MHz C) Run above 10 MHz D) Not oscillate.

Description : A series mode crystal is marked 10.000 MHz., It is used in a circuit that operates the crystal in its parallel mode. The circuit can be expected to A) Run below 10 MHz B) Run at 10 MHz C) Run above 10 MHz D) Not oscillate.

Last Answer : C) Run above 10 MHz

Six (6) MHz crystal oscillator has a stability of 1 part in 106. The largest frequency error expected of this crystals A) 0.06 Hz B) 0.6 Hz C) 6 Hz D) 60 Hz.

Description : Six (6) MHz crystal oscillator has a stability of 1 part in 106. The largest frequency error expected of this crystals A) 0.06 Hz B) 0.6 Hz C) 6 Hz D) 60 Hz.

Last Answer : C) 6 Hz

An oscillator that uses crystal control should be A) Frequency stable B) useful only at low frequencies C) AVFO D) none of the above.

Description : An oscillator that uses crystal control should be A) Frequency stable B) useful only at low frequencies C) AVFO D) none of the above.

Last Answer : A) Frequency stable

The ideal characteristic of a voltage stablizer is A) constant output voltage with low internal resistance B) constant output current with low internal resistance C) constant output voltage with high internal resistance D) constant internal resistance with variable output voltage.

Description : The ideal characteristic of a voltage stablizer is A) constant output voltage with low internal resistance B) constant output current with low internal resistance C) constant output voltage with high internal resistance D) constant internal resistance with variable output voltage.

Last Answer : A) constant output voltage with low internal resistance

The Bandwidth of an RC-coupled amplifier is limited by: A) coupling capacitors at the low frequency end and bypass capacitors at the high frequency end B) coupling capacitors at the high frequency end and bypass capacitors at the low frequency end C) bypass and coupling capacitors at the low frequency end and shunt capacitors at the high frequency end and D) shunt capacitors at the low frequency end and bypass as well as coupling capacitors at the high frequency end.

Description : The Bandwidth of an RC-coupled amplifier is limited by: A) coupling capacitors at the low frequency end and bypass capacitors at the high frequency end B) coupling capacitors at the high frequency ... at the low frequency end and bypass as well as coupling capacitors at the high frequency end.

Last Answer : C) bypass and coupling capacitors at the low frequency end and shunt capacitors at the high frequency end and

Emitter follower is used for (a) reducing the gain (b) increasing the distortion (c) impedance matching (d) none of these

Description : Emitter follower is used for (a) reducing the gain (b) increasing the distortion (c) impedance matching (d) none of these

Last Answer : (c) impedance matching

The current gain of emitter follower is:

Description : The current gain of emitter follower is: A) less than one B) more than one C) zero D) unpredictable

Last Answer : The current gain of emitter follower is: more than one

An emitter follower circuit is widely used in electronic instruments because

Description : An emitter follower circuit is widely used in electronic instruments because (A) Its voltage gain is less than unity (B) its output impedance is high and input impedance is low (C) its output impedance is low and input impedance is high (D) none of the above

Last Answer : Don't no happy be

What is an emitter follower BJT circuit ?

Description : What is an emitter follower BJT circuit ? (A) Common Collector Amplifier (B) Common Emitter Amplifier (C) Common Base Amplifier (D) None of the above

Last Answer : What is an emitter follower BJT circuit ? (A) Common Collector Amplifier (B) Common Emitter Amplifier (C) Common Base Amplifier (D) None of the above

Draw output characteristics of common emitter [CE] configuration and explain active, saturation and cut-off regions in detail.

Description : Draw output characteristics of common emitter [CE] configuration and explain active, saturation and cut-off regions in detail.

Last Answer : Characteristics of common emitter [CE] configuration Explanation : (1) Active Region: In this region collector junction is reverse biased and emitter junction is forward biased. It is ... the transistor collector current is approximately given by VCC / RC and independent of base current.

Which among the following is correct about goals in cryptography: a) Confidentiality - Only an authorized recipient should be able to extract the contents of the message from its encrypted form. Resulting from steps to hide, stop or delay free access to the encrypted information. b) Message Integrity - The recipient should be able to determine if the message has been altered. c) Sender Authentication - The recipient should be able to verify from the message, the identityof the sender, the origin or the path it traveled (or combinations) so to validate claims fromemitter or to validated the recipient expectations.d) Sender Non repudiation - The emitter should not be able to deny sending the messagee) None of Thesef) All of the Above

Description : Which among the following is correct about goals in cryptography: a) Confidentiality - Only an authorized recipient should be able to extract the contents of the message from its encrypted form. Resulting from steps ... not be able to deny sending the message e) None of These f) All of the Above

Last Answer : f) All of the Above

What is CB, CE and CC configuration ?

Description : What is CB, CE and CC configuration ?

Last Answer : Buffer : A device or a circuit used to isolate two pt'ne circuits or stages. The emitter follows is a example of buffer. Alpha = IC / IE Beta = IC / IB

(i) Discuss ideal and practical voltage source (ii) Compare CB, CC and CE configuration

Description : (i) Discuss ideal and practical voltage source (ii) Compare CB, CC and CE configuration

Last Answer : (i) Discuss ideal and practical voltage source Ideal voltage source The ideal voltage source has a constant voltage across its terminal, irrespective of the current drawn from the source. Ideal Voltage Source have zero ... to reduce. (ii) Compare CB, CC and CE configuration

Compare between CB , CE & CC transistor configuration.

Description : Compare between CB , CE & CC transistor configuration.

Last Answer : Parameter CB CE CC I/P impedance Low Or 50Ω Medium Or 600Ωto 4kΩ High Or 1 MΩ Current Gain Less than or equal to 1 High Highest Voltage Gain Medium Medium Less ... k Ω to 50 k Ω Low Or 50 Ω Phase shift between input and output 0° 360° 0°

When no signal is being received, the loudspeaker is not entirely silent as a result of the presence of A. parasitic oscillations in some of the receiver stages. B. negative feedback in each stage. C. spurious frequencies as a result of improper neutralization. D. internal receiver noise.

Description : When no signal is being received, the loudspeaker is not entirely silent as a result of the presence of A. parasitic oscillations in some of the receiver stages. B. negative feedback in each stage. C. spurious frequencies as a result of improper neutralization. D. internal receiver noise.

Last Answer : D. internal receiver noise.

Assertion:- A single human cell has approximately two meter long thread of DNA distributed in each chromosome. Reason:- Durring different stages of ce

Description : Assertion:- A single human cell has approximately two meter long thread of DNA distributed in each chromosome. Reason:- Durring different stages of ce

Last Answer : Assertion:- A single human cell has approximately two meter long thread of DNA distributed in each ... D. If both Assertion & Reason are false.

Given below is a schematic break-up of the phases/stages of cell cycle :- Which one of the following is the correct indication of the stage/phase in t

Description : Given below is a schematic break-up of the phases/stages of cell cycle :- Which one of the following is the correct indication of the stage/phase in t

Last Answer : Given below is a schematic break-up of the phases/stages of cell cycle :- Which one of the ... Metaphase C. C- Karyokinesis D. D- Synthesis phase

Given below is a schematic break-up of the phases/stages of cell cycle. Which one of the following is the correct indication of the stage/phase in the cell cycle? (a) C - karyokinesis (b) D - synthetic phase (c) A - cytokinesis (d) B - metaphase

Description : Given below is a schematic break-up of the phases/stages of cell cycle. Which one of the following is the correct indication of the stage/phase in the cell cycle? (a) C - karyokinesis (b) D - synthetic phase (c) A - cytokinesis (d) B - metaphase

Last Answer : (b) D - synthetic phase

Single stage CE amplifier

Description : Single stage CE amplifier

Last Answer : Requirement(Necessity) of Multistage amplifier: -In many applications we required a high gain. But sometimes gain produced by an amplifier is not sufficient so to increase the gain, we ... necessity of multistage amplifier is for providing high gain. It is also required for high bandwidth.

How is the output signal developed in the common-emitter detector?

Description : How is the output signal developed in the common-emitter detector?

Last Answer : By the collector current flow through R4.

The common-emitter transistor circuit can amplify a small current signal because a small change in the signal current produces one of the following. Does the change in signal produce a large change in the: w) emitter-base voltage x) base current y) collector current z) collector voltage

Description : The common-emitter transistor circuit can amplify a small current signal because a small change in the signal current produces one of the following. Does the change in signal produce a large change in the: w) emitter-base voltage x) base current y) collector current z) collector voltage

Last Answer : ANSWER: Y -- COLLECTOR CURRENT

A 1 Mhz carrier is amplitude modulated by a pure 200-Hz audio test tone. Which of the following combinations of frequencies represent the total content of the AM signal? A. 1 MHz and 200 Hz B. 1 MHz and 1000.2 kHz C. 999.8 kHz, 1000 kHz, and 1000.2 kHz D. 999.8 kHz and 1000.2 kHz

Description : A 1 Mhz carrier is amplitude modulated by a pure 200-Hz audio test tone. Which of the following combinations of frequencies represent the total content of the AM signal? A. 1 MHz and 200 Hz B. 1 MHz and 1000.2 kHz C. 999.8 kHz, 1000 kHz, and 1000.2 kHz D. 999.8 kHz and 1000.2 kHz

Last Answer : C. 999.8 kHz, 1000 kHz, and 1000.2 kHz

When the nurse observes that the patient’s systolic blood pressure is less than 80–90 mm Hg, respirations are rapid and shallow, heart rate is over 150 beats per minute, and urine output is less than 30 cc per hour, the nurse recognizes that the patient is demonstrating which stage of shock? a) Compensatory In compensatory shock, the patient’s blood pressure is normal, respirations are above 20, and heart rate is above 100 but below 150. b) Progressive In progressive shock, the patient’s skin appears mottled and mentation demonstrates lethargy. c) Refractory In refractory or irreversible shock, the patient requires complete mechanical and pharmacologic support. d) Irreversible In refractory or irreversible shock, the patient requires complete mechanical and pharmacologic support.

Description : When the nurse observes that the patient's systolic blood pressure is less than 80-90 mm Hg, respirations are rapid and shallow, heart rate is over 150 beats per minute, and ... d) Irreversible In refractory or irreversible shock, the patient requires complete mechanical and pharmacologic support.

Last Answer : a) Compensatory In compensatory shock, the patient’s blood pressure is normal, respirations are above 20, and heart rate is above 100 but below 150.

anonymous · Answer 1 · 2021-08-21T15:27:07+0000

Answer :

A) Two CE stages

answered Aug 21, 2021 by anonymous

Which of the following combinations has no phase inversion of the signal? A) Two CE stages B) CE and CC stages C) Three CE stages D) CE stage and emitter follower.

Please log in or register to add a comment.

Please log in or register to answer this question.

1 Answer

Answer :

Please log in or register to add a comment.

Related questions