A series mode crystal is marked 10.000 MHz., It is used in a circuit that operates the crystal in its parallel mode. The circuit can be expected to A) Run below 10 MHz B) Run at 10 MHz C) Run above 10 MHz D) Not oscillate.

A series mode crystal is marked 10.000 MHz., It is used in a circuit that operates the crystal in its parallel mode. The circuit can be expected to A) Run below 10 MHz
B) Run at 10 MHz
C) Run above 10 MHz
D) Not oscillate.
by

1 Answer

Answer :

C) Run above 10 MHz
by

Related questions

Six (6) MHz crystal oscillator has a stability of 1 part in 106. The largest frequency error expected of this crystals A) 0.06 Hz B) 0.6 Hz C) 6 Hz D) 60 Hz.

Description : Six (6) MHz crystal oscillator has a stability of 1 part in 106. The largest frequency error expected of this crystals A) 0.06 Hz B) 0.6 Hz C) 6 Hz D) 60 Hz.

Last Answer : C) 6 Hz

What conditions are required for an amplifier to oscillate A) There must be feedback B) The feedback must be in phase C) The gain must be greater than the loss D) All the above are regd.

Description : What conditions are required for an amplifier to oscillate A) There must be feedback B) The feedback must be in phase C) The gain must be greater than the loss D) All the above are regd.

Last Answer : B) The feedback must be in phase

An oscillator that uses crystal control should be A) Frequency stable B) useful only at low frequencies C) AVFO D) none of the above.

Description : An oscillator that uses crystal control should be A) Frequency stable B) useful only at low frequencies C) AVFO D) none of the above.

Last Answer : A) Frequency stable

Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback

Description : Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback

Last Answer : C) All oscillators generate sine waves

Which of the following methods cannot be used to increase the bandwidth for cascaded RF amplifier stages? A) Wave traps in each stage B) Stagger tuning C) A shunt damping resistor across each tuned circuit D) Doubled tuned transformers with tighter coupling

Description : Which of the following methods cannot be used to increase the bandwidth for cascaded RF amplifier stages? A) Wave traps in each stage B) Stagger tuning C) A shunt damping resistor across each tuned circuit D) Doubled tuned transformers with tighter coupling

Last Answer : A) Wave traps in each stage

Which of the following circuit would be preferred for a 455 kHz IF amplifier? A) A resistance loaded B) Double tuned transformer C) Video amplifier D) Class C

Description : Which of the following circuit would be preferred for a 455 kHz IF amplifier? A) A resistance loaded B) Double tuned transformer C) Video amplifier D) Class C

Last Answer : B) Double tuned transformer

Foldback current limiting has the advantage of A) Better pass transistor protection for long term overloads B) A defined turn on point C) Circuit simplicity D) All of the above.

Description : Foldback current limiting has the advantage of A) Better pass transistor protection for long term overloads B) A defined turn on point C) Circuit simplicity D) All of the above.

Last Answer : A) Better pass transistor protection for long term overloads

A crow bar is a power supply circuit that provides A) Conventional current limiting B) Foldback current. limiting C) Temperature control D) Voltage limiting.

Description : A crow bar is a power supply circuit that provides A) Conventional current limiting B) Foldback current. limiting C) Temperature control D) Voltage limiting.

Last Answer : D) Voltage limiting.

The change in base current will be A) 0.66 micro ampere B) 6.6 micro amperes C) 66 micro amperes D) 660 micro amperes.

Description : The change in base current will be A) 0.66 micro ampere B) 6.6 micro amperes C) 66 micro amperes D) 660 micro amperes.

Last Answer : A) 0.66 micro ampere

In an amplifier if conductor during the cycle is from 0 to 90° and again from 180° to 270°, the amplifier will be termed as A) Class A B) Class B C) Class C D) Class AB.

Description : In an amplifier if conductor during the cycle is from 0 to 90° and again from 180° to 270°, the amplifier will be termed as A) Class A B) Class B C) Class C D) Class AB.

Last Answer : B) Class B

Which distortion is least objectionable in case of audio amplifers? A) Phase distortion B) Frequency distortion C) Harmonic distortion D) Inter modulation distortion.

Description : Which distortion is least objectionable in case of audio amplifers? A) Phase distortion B) Frequency distortion C) Harmonic distortion D) Inter modulation distortion.

Last Answer : A) Phase distortion

A push pull amplifier balances out A) Odd harmonics B) Even harmonics C) Both odd as well as even harmonics D) Neither odd nor even harmonics.

Description : A push pull amplifier balances out A) Odd harmonics B) Even harmonics C) Both odd as well as even harmonics D) Neither odd nor even harmonics.

Last Answer : A) Odd harmonics

Which amplifier will be preferred for highest gain? A) Darlington's pair B) Cascade amplifier C) Cascode amplifier D) Depends on the circuitry

Description : Which amplifier will be preferred for highest gain? A) Darlington's pair B) Cascade amplifier C) Cascode amplifier D) Depends on the circuitry

Last Answer : C) Cascode amplifier

Which of the following contributes to harmonics distortion in amplifiers? A) Positive feedback B) Presence of noise C) Defective active device D) Non linearity in active device.

Description : Which of the following contributes to harmonics distortion in amplifiers? A) Positive feedback B) Presence of noise C) Defective active device D) Non linearity in active device.

Last Answer : D) Non linearity in active device.

In an amplifier the collector voltage equals the full V+ of 28 V instead of the normal 12 V which of the following can be the trouble? A) RL is open B) Cc is open C) RE is open D) CE is shorted.

Description : In an amplifier the collector voltage equals the full V+ of 28 V instead of the normal 12 V which of the following can be the trouble? A) RL is open B) Cc is open C) RE is open D) CE is shorted.

Last Answer : B) Cc is open

In a resistance loaded amplifier, the gain decreases a high frequencies because A) Of decreasing reactance of the stray CT B) Increasing reactance of the stray CT C) Increasing reactance of CC D) Decreasing reactance of CC.

Description : In a resistance loaded amplifier, the gain decreases a high frequencies because A) Of decreasing reactance of the stray CT B) Increasing reactance of the stray CT C) Increasing reactance of CC D) Decreasing reactance of CC.

Last Answer : D) Decreasing reactance of CC.

An ideal voltage amplifier should have A) Ri = 0, R0 = 0 B) Ri = 0, R0 =∞ C) Ri = ∞, R0 = 0 D) Ri = ∞, R0 = ∞.

Description : An ideal voltage amplifier should have A) Ri = 0, R0 = 0 B) Ri = 0, R0 =∞ C) Ri = ∞, R0 = 0 D) Ri = ∞, R0 = ∞.

Last Answer : C) Ri = ∞, R0 = 0

A IGFET is a A) Linear device B) Square law device C) Half power device D) 3/2 power law device.

Description : A IGFET is a A) Linear device B) Square law device C) Half power device D) 3/2 power law device.

Last Answer : B) Square law device

An FET has a gate source bias of 2 V. The ac input signal is ± 1.2 V. The class of operation is A) A B) B C) C D) AB

Description : An FET has a gate source bias of 2 V. The ac input signal is ± 1.2 V. The class of operation is A) A B) B C) C D) AB

Last Answer : D) AB

In a resistance loaded, RC coupled amplifier the dc component is blocked by A) Load resistance RL B) Coupling capacitor, CC C) RB D) The transistor.

Description : In a resistance loaded, RC coupled amplifier the dc component is blocked by A) Load resistance RL B) Coupling capacitor, CC C) RB D) The transistor.

Last Answer : B) Coupling capacitor, CC

If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the input signal C) Need for high dc collector supply D) Clipping of output in the negative half of the input signal

Description : If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the ... for high dc collector supply D) Clipping of output in the negative half of the input signal

Last Answer : B) Clipping of output in the positive half of the input signal

Which of the following combinations has no phase inversion of the signal? A) Two CE stages B) CE and CC stages C) Three CE stages D) CE stage and emitter follower.

Description : Which of the following combinations has no phase inversion of the signal? A) Two CE stages B) CE and CC stages C) Three CE stages D) CE stage and emitter follower.

Last Answer : A) Two CE stages

The Darlington pair consists of the following two stages A) CE and CC B) Both C) Both CC D) CE and CB

Description : The Darlington pair consists of the following two stages A) CE and CC B) Both C) Both CC D) CE and CB

Last Answer : C) Both CC

Common base configuration is little used because A) It has low input impedance B) It has high input impedance C) It does not heat up D) It has very high gain.

Description : Common base configuration is little used because A) It has low input impedance B) It has high input impedance C) It does not heat up D) It has very high gain.

Last Answer : A) It has low input impedance

As compared to a CB amplifier, a CE amplifier has A) Lower current amplification B) Higher current amplification C) Higher input resistance. D) Both (B) & (C)

Description : As compared to a CB amplifier, a CE amplifier has A) Lower current amplification B) Higher current amplification C) Higher input resistance. D) Both (B) & (C)

Last Answer : D) Both (B) & (C)

Current limited power supplies can prevent damage to A) Rectifier diodes and power transformers. B) Pass transistors C) Other circuits in the system D) All of the above.

Description : Current limited power supplies can prevent damage to A) Rectifier diodes and power transformers. B) Pass transistors C) Other circuits in the system D) All of the above.

Last Answer : D) All of the above.

In general, MOV devices are used to protect electronic equipment from dangerous operating conditions such as A) High temperatures B) Line transients C) Over current D) All of the above.

Description : In general, MOV devices are used to protect electronic equipment from dangerous operating conditions such as A) High temperatures B) Line transients C) Over current D) All of the above.

Last Answer : D) All of the above.

Load regulation is a measure of a power supplies ability keep a constant output under conditions of changing A) Line voltage B) Current demand C) Temperature D) Oscillator frequency.

Description : Load regulation is a measure of a power supplies ability keep a constant output under conditions of changing A) Line voltage B) Current demand C) Temperature D) Oscillator frequency.

Last Answer : A) Line voltage

What is the phase relationship of the signal at the collector of Q2 to the signal at the collector of Q, A) 0° B) 90° C) 180° D) 360°.

Description : What is the phase relationship of the signal at the collector of Q2 to the signal at the collector of Q, A) 0° B) 90° C) 180° D) 360°.

Last Answer : C) 180°

The major function of transistor. Q2 is A) It provides voltage gain B) It provides the feedback signal C) It isolates the oscillator from loading effects D) It provides a phase shift.

Description : The major function of transistor. Q2 is A) It provides voltage gain B) It provides the feedback signal C) It isolates the oscillator from loading effects D) It provides a phase shift.

Last Answer : ) It provides a phase shift.

The ideal characteristic of a voltage stablizer is A) constant output voltage with low internal resistance B) constant output current with low internal resistance C) constant output voltage with high internal resistance D) constant internal resistance with variable output voltage.

Description : The ideal characteristic of a voltage stablizer is A) constant output voltage with low internal resistance B) constant output current with low internal resistance C) constant output voltage with high internal resistance D) constant internal resistance with variable output voltage.

Last Answer : A) constant output voltage with low internal resistance

The Bandwidth of an RC-coupled amplifier is limited by: A) coupling capacitors at the low frequency end and bypass capacitors at the high frequency end B) coupling capacitors at the high frequency end and bypass capacitors at the low frequency end C) bypass and coupling capacitors at the low frequency end and shunt capacitors at the high frequency end and D) shunt capacitors at the low frequency end and bypass as well as coupling capacitors at the high frequency end.

Description : The Bandwidth of an RC-coupled amplifier is limited by: A) coupling capacitors at the low frequency end and bypass capacitors at the high frequency end B) coupling capacitors at the high frequency ... at the low frequency end and bypass as well as coupling capacitors at the high frequency end.

Last Answer : C) bypass and coupling capacitors at the low frequency end and shunt capacitors at the high frequency end and

What is the impedance of a crystal at its resonant frequency when it is used in the parallel mode?

Description : What is the impedance of a crystal at its resonant frequency when it is used in the parallel mode?

Last Answer : Maximum

What is the impedance of a crystal at its resonant frequency when it is used in the series mode?

Description : What is the impedance of a crystal at its resonant frequency when it is used in the series mode?

Last Answer : Minimum.

A capacitor and a coil are connected in series. The capacitor is charged and allowed to discharge through the coil. The current that will then flow through the capacitor-coil combination will do one of the following things. Will it: w) flow in one direction, beginning at a maximum and decreasing rapidly to zero x) oscillate indefinitely y) oscillate but diminish steadily to zero z) oscillate at high frequency at first but then at slower frequency

Description : A capacitor and a coil are connected in series. The capacitor is charged and allowed to discharge through the coil. The current that will then flow through the capacitor-coil combination will do ... but diminish steadily to zero z) oscillate at high frequency at first but then at slower frequency  

Last Answer : ANSWER: Y -- OSCILLATE BUT DIMINISH STEADILY TO ZERO

Fiber optic cable operates near _______ frequencies. A. 800 THz B. 20 MHz C. 200 MHz D. 2 GHz

Description : Fiber optic cable operates near _______ frequencies. A. 800 THz B. 20 MHz C. 200 MHz D. 2 GHz

Last Answer : A. 800 THz

A factory is served by a 220 V supply line. In a circuit protected by a fuse marked 10 A, the maximum number of 100 W lamps in parallel that can be tu

Description : A factory is served by a 220 V supply line. In a circuit protected by a fuse marked 10 A, the maximum number of 100 W lamps in parallel that can be tu

Last Answer : A factory is served by a 220 V supply line. In a circuit protected by a fuse marked 10 A, the maximum number of ... on, is A. 11 B. 22 C. 33 D. 66

The Q factor of a coil at resonant frequency 1.5 MHz of an RLC series circuit is 150. The Bandwidth is : -

Description : The Q factor of a coil at resonant frequency 1.5 MHz of an RLC series circuit is 150. The Bandwidth is : - a) 225 MHz b) 1.06 MHz c) 10 KHz d) 10 MHz

Last Answer : The Q factor of a coil at resonant frequency 1.5 MHz of an RLC series circuit is 150. The Bandwidth is : - 10 KHz

The winch shown in the illustration operates in any of the positions with the master switch in the 'lower' direction, but will not 'hoist' in any of the master switch hoist positions. Which of the listed faults could be the cause? EL-0102 A. Master switch contact 'MS3' may have defective springs. B. Contactor '3M' coil could have an open winding. C. Contact '2M' in the power circuit may be badly corroded. D. Series relay 'FR' may be open.

Description : The winch shown in the illustration operates in any of the positions with the master switch in the 'lower' direction, but will not 'hoist' in any of the master switch hoist positions. Which of the listed faults ... '2M' in the power circuit may be badly corroded. D. Series relay 'FR' may be open.

Last Answer : Answer: A

A 10,000-watt motor operates an elevator weighing 5000 newtons. Assuming no frictional losses, how high is the elevator raised in 10 seconds. Is it raised: w) 2 meters x) 20 meters y) 50 meters z) 100 meters

Description : A 10,000-watt motor operates an elevator weighing 5000 newtons. Assuming no frictional losses, how high is the elevator raised in 10 seconds. Is it raised: w) 2 meters x) 20 meters y) 50 meters z) 100 meters

Last Answer : ANSWER: X -- 20 METERS

In which of the following compounds the carbon marked with asterisk is expected to have greatest positive charge ?

Description : In which of the following compounds the carbon marked with asterisk is expected to have greatest positive charge ?

Last Answer : In which of the following compounds the carbon marked with asterisk is expected to have greatest positive charge ? ... (3)-CH_(2)-overset(+)Mgbar(C)l`

An endodontic therapy was completed on a tooth with a periapical radiolucency. Marked reduction in size of radiolucency is expected in approximately: A. One year B. 6 months C. 3 months

Description : An endodontic therapy was completed on a tooth with a periapical radiolucency. Marked reduction in size of radiolucency is expected in approximately: A. One year B. 6 months C. 3 months

Last Answer : A. One year

If MN/MX is low the 8086 operates in ______ mode.

Description : If MN/MX is low the 8086 operates in  ______ mode.   (a) Minimum (b) Maximum (c) Minimum & Maximum (d) Medium 

Last Answer : If MN/MX is low the 8086 operates in  Maximum mode. 

A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input

Description : A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is :

Last Answer : A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is : 200 V

Fill in the blank(s) with the appropriate word(s) i. A MOSFET operates in the ________________ mode when vGS < vGS(th)

Description : Fill in the blank(s) with the appropriate word(s)  i. A MOSFET operates in the ________________ mode when vGS < vGS(th)  ii. In the ohmic region of operation of a MOSFET vGS - vGS (th) ... ix. The safe operating area of a MOSFET is restricted on the left hand side by the ________________ limit. 

Last Answer : i. A MOSFET operates in the Cut off mode when vGS < vGS(th) ii. In the ohmic region of operation of a MOSFET vGS - vGS (th) is greater than vDS. iii. rDS (ON) of a MOSFET decreases ... Distributed under Creative Commons Attribution-ShareAlike - CC BY-SA. Version 2 EE IIT, Kharagpur

When a line commutated converter operates in the inverter mode

Last Answer : When a line commutated converter operates in the inverter mode It delivers real power to the A.C. supply.

A striking feature of living cells is a marked difference between the composition of the cytosol and the extracellular milieu. Which of the following statement(s) concerning the mechanisms of maintenance of these differences is/are true? a. The cell membrane is able to maintain a 10,000 fold gradient between the extracellular concentration of ionized calcium and the intracellular concentration b. The key to these differences is the fact that the plasma membrane is normally impermeable to sodium, potassium and calcium c. The selectivity of biologic membranes is highly consistent and seldom changes d. The selectivity of cell membranes relates only to ions and not organic compounds

Description : A striking feature of living cells is a marked difference between the composition of the cytosol and the extracellular milieu. Which of the following statement(s) concerning the mechanisms of maintenance ... d. The selectivity of cell membranes relates only to ions and not organic compounds

Last Answer : Answer: a The survival of the cell requires that cytosolic composition be maintained within narrow limits, despite the constant influx of nutrients and the simultaneous outflow of waste. A ... be altered drastically as a result of regulatory or signaling processes that occur within the cell

What is the required quality factor for an SSB filter with the following data: center frequency= 1 MHz, the desired attenuation level of the unwanted sideband= 80 dB and the separation between sidebands= 200 Hz? A. 1,250 B. 12,500 C. 125,000 D. 25,000

Description : What is the required quality factor for an SSB filter with the following data: center frequency= 1 MHz, the desired attenuation level of the unwanted sideband= 80 dB and the separation between sidebands= 200 Hz? A. 1,250 B. 12,500 C. 125,000 D. 25,000

Last Answer : C. 125,000

What is the frequency range of an aircraft’s Very High Frequency (VHF) communications? A. 118.000 MHz to 136.975 MHz (worldwide up to 151.975 MHz) B. 108.000 MHz to 117.95 MHz C. 329.15 MHz to 335.00 MHz D. 2.0000 MHz to 29.999 MHz

Description : What is the frequency range of an aircraft’s Very High Frequency (VHF) communications? A. 118.000 MHz to 136.975 MHz (worldwide up to 151.975 MHz) B. 108.000 MHz to 117.95 MHz C. 329.15 MHz to 335.00 MHz D. 2.0000 MHz to 29.999 MHz

Last Answer : A. 118.000 MHz to 136.975 MHz (worldwide up to 151.975 MHz)

Assume a frequency range of 401.000 MHz to 401.050 MHz, if you apply 25 kHz channeling plan, determine the center frequency of the first channel from the lower limit. A. 401.010 MHz B. 401.0125 MHz C. 401.025 MHz D. 401.00625 MHz

Description : Assume a frequency range of 401.000 MHz to 401.050 MHz, if you apply 25 kHz channeling plan, determine the center frequency of the first channel from the lower limit. A. 401.010 MHz B. 401.0125 MHz C. 401.025 MHz D. 401.00625 MHz

Last Answer : B. 401.0125 MHz