The transformer utilization factor of full wave bridge rectifier is

The transformer utilization factor of full wave bridge rectifier is 

 (A) 0.812 (B) 0.286 (C) 0.693 (D) 0.782
by

1 Answer

Answer :

The transformer utilization factor of full wave bridge rectifier is 0.286 

by

Related questions

Define following parameter of rectifier: (i) Ripple factor (ii) Efficiency (iii) Peak Inverse Voltage (iv) Transformer utilization factor

Description : Define following parameter of rectifier: (i) Ripple factor (ii) Efficiency (iii) Peak Inverse Voltage (iv) Transformer utilization factor

Last Answer : (i) Ripple Factor - Ripple factor (γ) may be defined as the ratio of the root mean square (rms) value of the ripple voltage to the absolute value of the DC component of the ... the same rectifier. Effective VA Rating of transformer is the average of primary and secondary VA rating of transformer.

The illustrated device is a _______. EL-0064 A. full wave bridge rectifier B. half wave bridge rectifier C. solid state voltage regulator D. direct current (DC) filter

Description : The illustrated device is a _______. EL-0064 A. full wave bridge rectifier B. half wave bridge rectifier C. solid state voltage regulator D. direct current (DC) filter

Last Answer : Answer: A

The use of four diodes, in a full-wave bridge rectifier circuit, will __________. A. provide unidirectional current to the load B. allow a very high leakage current from the load C. convert direct current to alternating current D. offer high opposition to current in two directions

Description : The use of four diodes, in a full-wave bridge rectifier circuit, will __________. A. provide unidirectional current to the load B. allow a very high leakage current from the load C. convert direct current to alternating current D. offer high opposition to current in two directions

Last Answer : Answer: A

Full wave bridge rectifier?

Description : Full wave bridge rectifier?

Last Answer : Full wave bridge rectifier: In full wave bridge rectifiers 4 diodes are using. During positive half cycle, D1 and D4 are in forward biased condition. In the negative half cycle of ac D3 and D2 ... a centre tap rectifier. But it requires more number of diodes than centre tap and half wave rectifiers

Why we are using the bridge rectifier in most of the circuits instead of full wave rectifier eventhough the output of both are same?

Description : Why we are using the bridge rectifier in most of the circuits instead of full wave rectifier eventhough the output of both are same?

Last Answer : Ans-In bridge type (FWR) rectifiers center tapping transformer are not required so small transformers are used and we will get twice of the out put voltage that of the center tapped FWR.

What main advantage does a bridge rectifier have over a conventional full-wave rectifier?

Description : What main advantage does a bridge rectifier have over a conventional full-wave rectifier?

Last Answer : The bridge rectifier can produce twice the voltage with the same size transformer.

What main advantage does a bridge rectifier have over a conventional full-wave rectifier?

Description : What main advantage does a bridge rectifier have over a conventional full-wave rectifier?

Last Answer : The bridge rectifier can produce double the voltage with the same size transformer.

Explain the operation of a full wave bridge rectifier with π filter using a neat diagram. Draw input and output waveforms.

Description : Explain the operation of a full wave bridge rectifier with π filter using a neat diagram. Draw input and output waveforms.

Last Answer : During positive half-cycle of input, the secondary voltage VAB is positive, so diodes D1 and D2 forward biased and D3 and D4 reverse biased. The load current flows from terminal A ... smooth DC voltage appears across the load. The input and output waveforms are shown in the figure.

Draw the circuit diagram and describe the working principle of full wave bridge rectifier. Draw its waveforms.

Description : Draw the circuit diagram and describe the working principle of full wave bridge rectifier. Draw its waveforms. 

Last Answer : During the first half cycle : During the first half cycle of the input voltage, the upper end of the transformer secondary winding is positive with respect to the lower end. Thus during the first ... , terminal D, diode D4, and terminal A back to transformer and output will positive half cycle.

Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier

Description : Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier 

Last Answer : Rectifier - This circuit convert AC signal into DC.

Draw and describe working of full wave rectifier using centre tapped transformer.

Description : Draw and describe working of full wave rectifier using centre tapped transformer.

Last Answer : Full wave Rectifier with Center tapped transformer(FWR): In full wave rectification, the rectifier conducts in both the cycles as two diodes are connected. Circuit diagram: Operation: 1. In ... both half-cycles of input AC voltage. Therefore DC is obtained across the load RL.

In a full wave rectifier circuit using centre tapped transformer, the peak voltage across half of the secondary

Description : In a full wave rectifier circuit using centre tapped transformer, the peak voltage across half of the secondary winding is 30 V. Then PIV is: (1) 30 V (2) 60 V (3) 15 V (4) 10 V

Last Answer : In a full wave rectifier circuit using centre tapped transformer, the peak voltage across half of the secondary winding is 30 V. Then PIV is: 60 V

A simple phase transformer has a maximum efficiency of 90% at full load and unity power factor. Efficiency at

Description : A simple phase transformer has a maximum efficiency of 90% at full load and unity power factor. Efficiency at half load at the same power factor is  (A) 86.7% (B) 88.26% (C) 88.9% (D) 87.8%

Last Answer : A simple phase transformer has a maximum efficiency of 90% at full load and unity power factor. Efficiency at half load at the same power factor is 87.8%

The most common source of excitation for synchronous motors is a/an ______________. A. stepup transformer B. half-wave rectifier C. DC supply D. AC supply

Description : The most common source of excitation for synchronous motors is a/an ______________. A. stepup transformer B. half-wave rectifier C. DC supply D. AC supply

Last Answer : Answer: C

An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Description : An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Last Answer : Solution:

An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to

Description :  An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to secondary turn’s ratio 12:1. The peak inverse voltage is A) 8.62 V B) 12 V C) 19.17 V D) 27.11 V 

Last Answer :  An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to secondary turn’s ratio 12:1. The peak inverse voltage is A) 8.62 V B) 12 V C) 19.17 V D) 27.11 V 

What was the major factor that led to the development of the full-wave rectifier?

Description : What was the major factor that led to the development of the full-wave rectifier?

Last Answer : The fact that the full-wave rectifier uses the full output, both half cycles, of the transformer.

Define given parameters and state their values for bridge rectifier (i) Ripple factor (ii) PIV of diode.

Description : Define given parameters and state their values for bridge rectifier (i) Ripple factor (ii) PIV of diode.

Last Answer : Ripple Factor: Ripple Factor is defined as the ratio of RMS value of the AC component of output to the DC or average value of the output. Mathematically it is expressed as, ( ... which appears across non-conducting reverse biased diode. (ii) PIV of diode for bridge rectifier-Vm

The ripple factor of a bridge rectifier is

Description : The ripple factor of a bridge rectifier is  1.0.48 2.0.812 3. 1.11 4. 1.21 

Last Answer : The ripple factor of a bridge rectifier is 0.48

Ripple factor for a half wave rectifier is ....

Description : Ripple factor for a half wave rectifier is  a. 1.65 b. 1.45 c. 1 d. 1.21 

Last Answer : Ripple factor for a half wave rectifier is 1.21

A single-phase full-bridge diode rectifier delivers a load current of 10A, which is ripple free.

Description : A single-phase full-bridge diode rectifier delivers a load current of 10A, which is ripple free. Average and rms values of diode currents are respectively   (a) 10A, 7.07A (b) 5A, 10A (c) 5A, 7.07A (d) 7.07A, 5A

Last Answer : A single-phase full-bridge diode rectifier delivers a load current of 10A, which is ripple free. Average and rms values of diode currents are respectively 5A, 7.07A

Full load copper loss in a transformer is 1600 watts. At half load the copper loss will be:

Description : Full load copper loss in a transformer is 1600 watts. At half load the copper loss will be: A) 6400 watt B) 1600 watt C) 800 watt D) 400 watt

Last Answer :  Full load cupper loss in a transformer is 1600 watts. At half load the cupper loss will be: 400 watt

A 500 kVA, 3-phase transformer has iron losses of 300 W and full load copper losses of 600 W. The percentage

Description : A 500 kVA, 3-phase transformer has iron losses of 300 W and full load copper losses of 600 W. The percentage load at which the transformer is expected to have maximum efficiency is  (A) 50.0% (B) 70.7% (C) 141.4% (D) 200.0%

Last Answer : A 500 kVA, 3-phase transformer has iron losses of 300 W and full load copper losses of 600 W. The percentage load at which the transformer is expected to have maximum efficiency is 70.7%

A single-phase, 50 kVA, 250 V/500 V two winding transformer has an efficiency of 95% at full load, unity

Description : A single-phase, 50 kVA, 250 V/500 V two winding transformer has an efficiency of 95% at full load, unity power factor. If it is re-configured as a 500 V/750 V auto-transformer, its efficiency at its new rated load at unity power factor will be  (A) 95.752% (B) 97.851% (C) 98.276% (D) 99.241%

Last Answer : A

In a transformer, zero voltage regulation at full load is

Description : In a transformer, zero voltage regulation at full load is   (a)Not possible   (b) Possible at unity power factor load   (c) Possible at leading power factor load   (d) Possible at lagging power factor load

Last Answer : In a transformer, zero voltage regulation at full load is Possible at leading power factor load 

The no-load current drawn by transformer is usually what per cent of the full-load current ?

Description :  The no-load current drawn by transformer is usually what per cent of the full-load current ?

Last Answer : 5 to 8 percentage of full load current

The full-load copper loss of a transformer is 1600 W At half-load, the copper loss will be?

Last Answer : The full-load copper loss of a trans¬former is 1600 W. At half-load, the copper loss will be 400 W.

In an actual transformer the iron loss remains practically constant from no load to full load because?

Description : In an actual transformer the iron loss remains practically constant from no load to full load because?

Last Answer : In an actual transformer the iron loss remains practically constant from no load to full load because core flux remains practically constant.

When the peak output voltage is 100 V the PIV for each diode in a center-tapped full-wave rectifier is (neglecting the diode drop)?

Description : When the peak output voltage is 100 V the PIV for each diode in a center-tapped full-wave rectifier is (neglecting the diode drop)?

Last Answer : Feel Free to Answer

What effect does an open diode have on the output voltage of a half wave rectifier and on a full wave rectifier?

Description : What effect does an open diode have on the output voltage of a half wave rectifier and on a full wave rectifier?

Last Answer : An open diode will result in no output from a half waverectifier, and an open diode will cut the output of a full waverectifier in half.

If input frequency of a full wave rectifier be n, then output frequency would be - (1) n/2 (2) n (3) 3n/2 (4) 2n

Description : If input frequency of a full wave rectifier be n, then output frequency would be - (1) n/2 (2) n (3) 3n/2 (4) 2n

Last Answer : (4) 2n Explanation: The frequency of a full-wave rectifier is double that of the input, if the input is a sine wave. A full-wave rectifier converts the whole of the input waveform to one ... both polarities of the input waveform to DC (direct current), and yields a higher mean output voltage.

The correct term for the illustrated circuit is a ________. EL-0063 A. single phase half wave high power rectifier B. three phase half wave rectifier C. three phase full wave rectifier D. a single phase full wave rectifier

Description : The correct term for the illustrated circuit is a ________. EL-0063 A. single phase half wave high power rectifier B. three phase half wave rectifier C. three phase full wave rectifier D. a single phase full wave rectifier

Last Answer : Answer: C

One diode of a full-wave rectifier has burned out in a shorted condition. Therefore, the output will be ____________. A. zero B. a rectified half-wave C. a rectified full-wave D. equal to the AC input

Description : One diode of a full-wave rectifier has burned out in a shorted condition. Therefore, the output will be ____________. A. zero B. a rectified half-wave C. a rectified full-wave D. equal to the AC input

Last Answer : Answer: D

A full-wave rectifier has one diode burned out in an open condition, what will be the output characteristic of the device? A. Zero B. Half-wave rectified C. Full-wave rectified D. Equal to the AC input

Description : A full-wave rectifier has one diode burned out in an open condition, what will be the output characteristic of the device? A. Zero B. Half-wave rectified C. Full-wave rectified D. Equal to the AC input

Last Answer : Answer: B

In the illustrated circuit, section II is considered to be a _______. EL-0085 A. full wave rectifier B. half wave rectifier C. quarter wave rectifier D. short wave rectifier

Description : In the illustrated circuit, section II is considered to be a _______. EL-0085 A. full wave rectifier B. half wave rectifier C. quarter wave rectifier D. short wave rectifier

Last Answer : Answer: A

Which of the following expresses the relationship of the input and output frequencies in a full wave rectifier? A. The output frequency is the same as input frequency. B. The output frequency is one-half the input frequency. C. The output frequency is twice the input frequency. D. The output frequency is four times the input frequency.

Description : Which of the following expresses the relationship of the input and output frequencies in a full wave rectifier? A. The output frequency is the same as input frequency. B. The output frequency is ... frequency is twice the input frequency. D. The output frequency is four times the input frequency.

Last Answer : Answer: C

Difference between half wave and full wave rectifier?

Description : Difference between half wave and full wave rectifier?

Last Answer : A10: The efficiency of half wave rectifier is not so good as that of full wave rectifier Because only one half of the input waveform reaches the output, it is very inefficient if used for ... reduced in the full-wave rectifier and being reduced further with the increase in the number of phases.

Full wave centre tap rectifier?

Description : Full wave centre tap rectifier?

Last Answer : In this method only two diodes are used. But it requires a center tap transformer. During the positive half cycle diode D1 conducts. In the negative half cycle diode D2 conducts. So in ... rectification converts both polarities of the input waveform to DC (direct current), and is more efficient.

Is a full-wave rectifier output easier to filter than that of a half-wave rectifier?

Description : Is a full-wave rectifier output easier to filter than that of a half-wave rectifier?

Last Answer : Yes.

What is the main disadvantage of a conventional full-wave rectifier?

Description : What is the main disadvantage of a conventional full-wave rectifier?

Last Answer : Peak voltage is half that of the half-wave rectifier.

What is the average voltage (Eavg) Output of a full-wave rectifier with an output of 100 volts peak?

Description : What is the average voltage (Eavg) Output of a full-wave rectifier with an output of 100 volts peak?

Last Answer : 63.7 volts.

What is the ripple frequency of a full-wave rectifier with an input frequency of 60 Hz?

Description : What is the ripple frequency of a full-wave rectifier with an input frequency of 60 Hz?

Last Answer : 120 hertz.

Is a full-wave rectifier output easier to filter than that of a half-wave rectifier?

Description : Is a full-wave rectifier output easier to filter than that of a half-wave rectifier?

Last Answer : Yes.

What is the main disadvantage of the conventional full wave rectifier?

Description : What is the main disadvantage of the conventional full wave rectifier?

Last Answer : The peak voltage is half that of a half-wave rectifier.

What is the average voltage (Eavg) output of a full-wave rectifier that has an output of 100 volts peak?

Description : What is the average voltage (Eavg) output of a full-wave rectifier that has an output of 100 volts peak?

Last Answer : 63.6 volts.

What is the ripple frequency of a full-wave rectifier with an input frequency of 60 Hz?

Description : What is the ripple frequency of a full-wave rectifier with an input frequency of 60 Hz?

Last Answer : 120 hertz.

The output from a full wave rectifier is (a) A pulsating uni-directional current (b) A DC voltage (c) Zero (d) An AC voltage

Description : The output from a full wave rectifier is (a) A pulsating uni-directional current (b) A DC voltage (c) Zero (d) An AC voltage

Last Answer : a) A pulsating uni-directional current

Draw the circuit diagram of shunt capacitor filter along with full wave rectifier. Draw the waveform of full wave rectifier output and shunt capacitor filter output.

Description : Draw the circuit diagram of shunt capacitor filter along with full wave rectifier. Draw the waveform of full wave rectifier output and shunt capacitor filter output.

Last Answer : Fig: Shunt capacitor filter along with full wave rectifier Fig: Waveform of full wave rectifier output and shunt capacitor filter output.

Compare half wave rectifier and full wave rectifier.

Description : Compare half wave rectifier and full wave rectifier. 

Last Answer : half wave rectifier and full wave rectifier :

Draw circuit diagram and waveforms for centre-tap full wave rectifier.

Description : Draw circuit diagram and waveforms for centre-tap full wave rectifier.

Last Answer : Circuit Diagram: