The 'h' parameter equivalent circuit of a junction transistor is valid for

The 'h' parameter equivalent circuit of a junction transistor is valid for 

 (A) High frequency, large signal operation (B) High frequency, small signal operation (C) Low frequency, large signal operation.
by

1 Answer

Answer :

The 'h' parameter equivalent circuit of a junction transistor is valid for Low frequency, large signal operation.

by

Related questions

A semiconductor device made up of a single p-n Junction is called a: w) transistor x) diode y) Fet z) integrated circuit

Description : A semiconductor device made up of a single p-n Junction is called a: w) transistor x) diode y) Fet z) integrated circuit

Last Answer : ANSWER: X -- DIODE

Which parameter is not changed by transistor?

Description : Which parameter is not changed by transistor? A. Frequency B. phase C. amplitude D. all of these

Last Answer : Frequency parameter is not changed by transistor.

What is junction transistor ?

Description : What is junction transistor ?

Last Answer : The origin of the word transistor is from the two words Transfer Resistor . It is so named because the transistor transmits the signal from the low-voltage circuit to the high-voltage circuit. ... transistor. The invention of the transistor is one of the best inventions of the twentieth century.

In the illustrated amplifier, the base of the transistor is what type of material? EL-0022 A. N type B. P type C. metal oxide insulator D. alloy junction material

Description : In the illustrated amplifier, the base of the transistor is what type of material? EL-0022 A. N type B. P type C. metal oxide insulator D. alloy junction material

Last Answer : Answer: A

Which of the following actions can be carried out in order to prevent thermal runaway in a transistor? A. Increase the current through the collector-base junction. B. Install a heat sink. C. Shift the 'Q' point to increase collector current. D. Increase the potential difference between the emitter and the base.

Description : Which of the following actions can be carried out in order to prevent thermal runaway in a transistor? A. Increase the current through the collector-base junction. B. Install a heat sink. ... point to increase collector current. D. Increase the potential difference between the emitter and the base.

Last Answer : Answer: B

Figure 'B' shown in the illustration represents a/an ____________. EL-0067 A. silicon controlled rectifier B. junction field effect transistor C. diac thyristor D. IG MOS field effect transistor

Description : Figure 'B' shown in the illustration represents a/an ____________. EL-0067 A. silicon controlled rectifier B. junction field effect transistor C. diac thyristor D. IG MOS field effect transistor

Last Answer : Answer: A

Figure 'A' of the diagram shown in the illustration represents a/an ____________. EL-0078 A. silicon controlled rectifier B. IG or MOS field effect transistor C. triac thyristor D. junction field effect transistor

Description : Figure 'A' of the diagram shown in the illustration represents a/an ____________. EL-0078 A. silicon controlled rectifier B. IG or MOS field effect transistor C. triac thyristor D. junction field effect transistor

Last Answer : Answer: B

Figure 'B' of the diagram shown in the illustration represents a/an ____________. EL-0065 A. silicon controlled rectifier B. junction field effect transistor C. diac thyristor D. IG or MOS field effect transistor

Description : Figure 'B' of the diagram shown in the illustration represents a/an ____________. EL-0065 A. silicon controlled rectifier B. junction field effect transistor C. diac thyristor D. IG or MOS field effect transistor

Last Answer : Answer: B

Which junction of the transistor in the common-emitter detector detects the modulation envelope?

Description : Which junction of the transistor in the common-emitter detector detects the modulation envelope?

Last Answer : Emitter-base junction

For normal operation of a transistor, the collector base junction is kept (a) Unbiased (b) forward biased (c) reverse biased (d) none

Description : For normal operation of a transistor, the collector base junction is kept (a) Unbiased (b) forward biased (c) reverse biased (d) none

Last Answer : (c) reverse biased

Which is the most important building block of electronic devices? (a) Diode (b) p-n junction (c) transistor (d) rectifier

Description : Which is the most important building block of electronic devices? (a) Diode (b) p-n junction (c) transistor (d) rectifier

Last Answer : b) p-n junction

A transistor has (A) One p-n junction. (B) Two p-n junction. (C) Four p-n junction. (D) Five p-n junction.

Description : A transistor has (A) One p-n junction. (B) Two p-n junction. (C) Four p-n junction. (D) Five p-n junction.

Last Answer : (B) Two p-n junction.

State reason BJT is called as bipolar junction transistor.

Description : State reason BJT is called as bipolar junction transistor.

Last Answer : BJT is called bipolar junction transistor because in BJT current conduction takes place due to majority as well as minority charge carriers.

Define junction field effect transistor (JFET) and give an example.

Description : Define junction field effect transistor (JFET) and give an example.

Last Answer : Junction Field-Effect Transistor: It is a semiconductor device having three terminals, namely Gate, Drain and Source, in which the current flow is controlled by an electric field set up by an external voltage applied ... : i) n-channel JFET and ii) p-channel JFET Examples of JFET: BFW 10, BFW 11 

A bipolar junction transistor (BJT) is used as a power control switch by biasing it in the cut-off region

Description : A bipolar junction transistor (BJT) is used as a power control switch by biasing it in the cut-off region (OFF state) or in the saturation region (ON state). In the ON state, for ... base-collector junction is reverse biased (D) both the base-emitter and base-collector junctions are forward biased

Last Answer : A BJT is as a power control switch by biasing it in cut-off region (OFF state) or in the saturation region (ON state). In  ON state, for BJT both the base-emitter and base- collector junctions are forward biased

In a junction transistor, the doping level of collector region is:

Description : In a junction transistor, the doping level of collector region is:  (1) Higher than emitter region (2) Lower than base region (3) Is higher than base region but lower than emitter region  (4) Independent of the doping of base and emitter regions.

Last Answer : In a junction transistor, the doping level of collector region is: Is higher than base region but lower than emitter region.

Draw construction of SCR using two transistor model. Explain its operation.

Description : Draw construction of SCR using two transistor model. Explain its operation.

Last Answer : Two Transistor Model of SCR or Thyristor

Draw the V-I characteristics of power transistor.

Description : Draw the V-I characteristics of power transistor. 

Last Answer : V-I characteristics of power transistor:

A Darlington transistor connection provides a transistor having a very large

Description : A Darlington transistor connection provides a transistor having a very large  a. Current gain b. Voltage gain c. Impedance gain d. Impedance matching gain

Last Answer : A Darlington transistor connection provides a transistor having a very large Current gain

When an NPN transistor is properly biased then most of the electrons from the emitter

Description : When an NPN transistor is properly biased then most of the electrons from the emitter   (A) recombine with holes in the base (B) recombine in the emitter itself (C) pass through the base to the collector (D) are stopped by the junction barrier

Last Answer : a

Which of the following statements is wrong for transistor biasing methods:

Description : Which of the following statements is wrong for transistor biasing methods:  1. The base resistor method does not provide stabilization of operating point 2. The biasing with feedback ... than collector feedback method 4.Voltage divider bias is widely used because it has stable operating point

Last Answer : Which of the following statements is wrong for transistor biasing methods:  1. The base resistor method does not provide stabilization of operating point 2. The biasing with feedback ... than collector feedback method 4.Voltage divider bias is widely used because it has stable operating point 

A FET is preferred over an ordinary transistor because it

Description : A FET is preferred over an ordinary transistor because it  1. Permits high degree of isolation between input & output circuits 2. Has low noise level 3. Has very high power gain 4. Has all the above properties 

Last Answer : A FET is preferred over an ordinary transistor because it Has all the above properties 

What satellite system parameter represents the quality of a satellite or an earth station receiver? A. Gain-to-Equivalent Noise Temperature Ratio (G/Te) B. Energy of Bit-to-Noise Density Ratio (Eb/No) C. Carrier-to-Noise Density Ratio (C/No) D. Bit energy

Description : What satellite system parameter represents the quality of a satellite or an earth station receiver? A. Gain-to-Equivalent Noise Temperature Ratio (G/Te) B. Energy of Bit-to-Noise Density Ratio (Eb/No) C. Carrier-to-Noise Density Ratio (C/No) D. Bit energy

Last Answer : A. Gain-to-Equivalent Noise Temperature Ratio (G/Te)

The surface integral of which parameter is zero? a) E b) D c) B d) H

Description : The surface integral of which parameter is zero? a) E b) D c) B d) H

Last Answer : c) B

The line integral of which parameter is zero for static fields? a) E b) H c) D d) B

Description : The line integral of which parameter is zero for static fields? a) E b) H c) D d) B

Last Answer : a) E

Why is the H-type T junction so named?

Description : Why is the H-type T junction so named?

Last Answer : The junction arm extends in a direction parallel to the H lines in the main waveguide.

What is a circuit parameter ?

Description : What is a circuit parameter ?

Last Answer : The components used in an electrical circuit, each of which performs a specific function, are called circuit parameters. E.g. , resistance , inductance , capacitance.

Under which of the following conditions is the relation, `Delta H = Delta E + P Delta V` valid for a system :-

Description : Under which of the following conditions is the relation, `Delta H = Delta E + P Delta V` valid for a system :-

Last Answer : Under which of the following conditions is the relation, `Delta H = Delta E + P ... and pressure D. Constant temperature, pressure and composition

Heat transfer co-efficient (h) for a fluid flowing inside a clean pipe is given by h = 0.023 (K/D) (DVρ/µ) 0.8 (CP .µ/k) 0.4 . This is valid for the value of NRe equal to (A) < 2100 (B) 2100-4000 (C) > 4000 (D) > 10000

Description : Heat transfer co-efficient (h) for a fluid flowing inside a clean pipe is given by h = 0.023 (K/D) (DVρ/µ) 0.8 (CP .µ/k) 0.4 . This is valid for the value of NRe equal to (A) < 2100 (B) 2100-4000 (C) > 4000 (D) > 10000

Last Answer : (D) > 10000

The Maxwell second equation that is valid in any conductor is a) Curl(H) = Jc b) Curl(E) = Jc c) Curl(E) = Jd d) Curl(H) = Jd

Description : The Maxwell second equation that is valid in any conductor is a) Curl(H) = Jc b) Curl(E) = Jc c) Curl(E) = Jd d) Curl(H) = Jd

Last Answer : a) Curl(H) = Jc

In a PN-junction with open circuit terminal (equilibrium), with P doping higher as compared to N

Description : In a PN-junction with open circuit terminal (equilibrium), with P doping higher as compared to N doping (A) N-side depletion region is small as compared to p-side depletion region (B) N-side ... depletion region (C) N-side depletion region is same as p-side depletion region (D) Cannot say

Last Answer : In a PN-junction with open circuit terminal (equilibrium), with P doping higher as compared to N doping N-side depletion region is small as compared to p-side depletion region

Kirchhoff's current law is applicable to 1. Closed loops in a circuit 2. Junction in a circuit 3. Magnetic circuits ...

Description : Kirchhoff's current law is applicable to 1. Closed loops in a circuit 2. Junction in a circuit 3. Magnetic circuits Which of the above is/are correct ?  (a) 1 only (b) 2 only (c) 3 only (d) 1, 2 and 3

Last Answer : Kirchhoff's current law is applicable to 1. Closed loops in a circuit 2. Junction in a circuit 3. Magnetic circuits Which of the above is/are correct ?  (a) 1 only (b) 2 only (c) 3 only (d) 1, 2 and 3

The p-type substrates in a conventional pn-junction isolated integrated circuit should be connected to:

Last Answer : The p-type substrates in a conventional pn-junction isolated integrated circuit should be connected to: The most negative potential available in the circuit.

An integrated circuit is A) A complicated circuit B) An integrating device C) Much costlier than a single transistor D) Fabricated on a tiny silicon chip

Description : An integrated circuit is A) A complicated circuit B) An integrating device C) Much costlier than a single transistor D) Fabricated on a tiny silicon chip

Last Answer : Answer : D

Which one among the following components can not be developed within an "integrated circuit"? (1) Diode (2) Triode (3) Transformer (4) Transistor

Description : Which one among the following components can not be developed within an "integrated circuit"? (1) Diode (2) Triode (3) Transformer (4) Transistor

Last Answer : (3) Transformer Explanation: Some components like transformers and inductors cannot be integrated into an IC except for very specialized high frequency applications. They have to be ... circuit boards as separate components and cannot be integrated into semiconductor based integrated circuits.

In a logic circuit the NOR and NAND gate functions ____________. A. must be accomplished with a common base transistor arrangement B. are available in diode form C. are exact opposites with the same NOR and NAND inputs D. have output conditions that are exact opposites to the output condition for OR and AND, respectively

Description : In a logic circuit the NOR and NAND gate functions ____________. A. must be accomplished with a common base transistor arrangement B. are available in diode form C. are exact opposites with the ... . have output conditions that are exact opposites to the output condition for OR and AND, respectively

Last Answer : Answer: D

In a logic circuit, the NOT gate function _____________. A. does not alter a logical input B. serves to amplify a given signal level C. must be accomplished with a common collector transistor arrangement D. reverses an input logic condition

Description : In a logic circuit, the NOT gate function _____________. A. does not alter a logical input B. serves to amplify a given signal level C. must be accomplished with a common collector transistor arrangement D. reverses an input logic condition

Last Answer : Answer: D

When troubleshooting a console circuit card suspected of being faulty, first check operating voltages, clean the card and then _________________. A. make sure wired connections and push-on connectors are tight B. test each resistor and capacitor on the card with an ohmmeter C. check the continuity of all printed circuit traces with an ohmmeter D. measure the gain of each transistor or integrated circuit

Description : When troubleshooting a console circuit card suspected of being faulty, first check operating voltages, clean the card and then _________________. A. make sure wired connections and push-on connectors ... circuit traces with an ohmmeter D. measure the gain of each transistor or integrated circuit

Last Answer : Answer: A

When troubleshooting a console circuit card which is suspected of being faulty, the first step would be to _____. A. pull the card and measure the value of all resistors B. check for the correct value and polarity of all power connections to the card C. de-energize and pull the card to visually inspect for burned components D. check for continuity of circuit board traces and then the gain of each transistor

Description : When troubleshooting a console circuit card which is suspected of being faulty, the first step would be to _____. A. pull the card and measure the value of all resistors B. check for the ... for burned components D. check for continuity of circuit board traces and then the gain of each transistor

Last Answer : Answer: C

Normally, the FIRST step in troubleshooting a transistor circuit card is to _____________. A. carefully remove the transistors from the card B. give the circuit an initial test with a signal generator C. test for continuity with a low voltage DC supply D. visually inspect the card

Description : Normally, the FIRST step in troubleshooting a transistor circuit card is to _____________. A. carefully remove the transistors from the card B. give the circuit an initial test with a signal generator C. test for continuity with a low voltage DC supply D. visually inspect the card

Last Answer : Answer: D

To conduct an in-circuit test of a transistor, you should use a/an ____________. A. voltmeter or transistor tester B. impedance meter C. ohmmeter or transistor tester D. wattmeter

Description : To conduct an in-circuit test of a transistor, you should use a/an ____________. A. voltmeter or transistor tester B. impedance meter C. ohmmeter or transistor tester D. wattmeter

Last Answer : Answer: A

Which of the procedures listed could result in damaging a transistor beyond repair? A. Applying incorrect polarity to the collector circuit. B. Applying excessive voltage to the input circuit. C. Careless soldering which would overheat the transistor. D. All of the above.

Description : Which of the procedures listed could result in damaging a transistor beyond repair? A. Applying incorrect polarity to the collector circuit. B. Applying excessive voltage to the input circuit. C. Careless soldering which would overheat the transistor. D. All of the above.

Last Answer : Answer: D

In order to check the performance of a transistor removed from its circuit, the instrument to be used should be a/an ____________. A. voltmeter or transistor tester B. impedance meter C. ohmmeter or transistor tester D. sensitive potentiometer

Description : In order to check the performance of a transistor removed from its circuit, the instrument to be used should be a/an ____________. A. voltmeter or transistor tester B. impedance meter C. ohmmeter or transistor tester D. sensitive potentiometer

Last Answer : Answer: C

When replacing a power transistor fitted with a heat sink in a circuit, a coating of silicone grease is applied between the transistor case and the heat sink. This is done to ____________. A. lubricate the transistor B. lubricate the heat sink C. aid in the removal of the heat sink D. provide maximum heat transfer

Description : When replacing a power transistor fitted with a heat sink in a circuit, a coating of silicone grease is applied between the transistor case and the heat sink. This is done to ____________. A. lubricate ... the heat sink C. aid in the removal of the heat sink D. provide maximum heat transfer

Last Answer : Answer: D

An integrated circuit is a. A complicated circuit b. An integrating device c. Much costlier than a single transistor d. Fabricated on a tiny silicon chip

Description : An integrated circuit is a. A complicated circuit b. An integrating device c. Much costlier than a single transistor d. Fabricated on a tiny silicon chip

Last Answer : Fabricated on a tiny silicon chip

_______is not as fast as SRAM but is cheaper and is used for main memory. Each bit uses a single capacitor and single transistor circuit.: a) DRAM b) SDRAM c) Both of Above d) None of These

Description : _______is not as fast as SRAM but is cheaper and is used for main memory. Each bit uses a single capacitor and single transistor circuit.: a) DRAM b) SDRAM c) Both of Above d) None of These

Last Answer : a) DRAM

Foldback current limiting has the advantage of A) Better pass transistor protection for long term overloads B) A defined turn on point C) Circuit simplicity D) All of the above.

Description : Foldback current limiting has the advantage of A) Better pass transistor protection for long term overloads B) A defined turn on point C) Circuit simplicity D) All of the above.

Last Answer : A) Better pass transistor protection for long term overloads

What method for checking transistors is cumbersome when more than one transistor is bad in a circuit?

Description : What method for checking transistors is cumbersome when more than one transistor is bad in a circuit?

Last Answer : The substitution method.