How will you change the action of a control valve ?

How will you change the action of a control valve ? 
by

1 Answer

Answer :

1. If the control valve is without bottom cap. The actual needs to be changed.

2. If bottom cap is provided.

a) Disconnect the stem from the actuator stem.

b) Separate the body from the bonnet.

c) Remove the bottom cap and the plug from body.

d) Detach the plug from the stem by removing the pin.

e) Fix the stem at the other end of the plug and fix the pin back.

f) Turn the body upside down. Connect it to the bonnet after inserting the plug and stem.

g) Connect back the stem to the actuator stem.

h) Fix back the bottom cap.

i) Calibrate the valve. 
by

Related questions

How will you select the control valve characteristics ?

Description : How will you select the control valve characteristics ?

Last Answer : The graphic display of flow various lift shows then the Desired or inherent characteristic is changed by variations pressure drop. This occurs as the process changes from condition where most of pressure drop takes ... the valve. b) The pressure drop across a valve should be as low as possible. 

How will you work on a control valve while it is line ?

Description : How will you work on a control valve while it is line ?

Last Answer : While the control valve is in line or in service, it has to be by passed and secondly the line to be depressurized and drained. 

How will you change the valve characteristics with positioner ?

Description : How will you change the valve characteristics with positioner ?

Last Answer : The positioner contains different types of came in it. selection of the proper cams in it.By selection of the proper cam the valve opening characteristics can be changed. 

What is a solenoid valve ? Where it is used ?

Description : What is a solenoid valve ? Where it is used ?

Last Answer :  A solenoid is electrically operated valve. It consist of a solenoid ( coil ) in which a magnetic plunger moves which is connected to the plug and tends to open or close the value. There are two types ... :  1. Normally open 2. Normally closed  USE : It is used for safety purpose. 

What are the different valve characteristic ?

Description : What are the different valve characteristic ?

Last Answer : The different types of valve characteristic are : 1. Linear 2. Equal Percentage 3. Quick Opening. 1.Linear: The valve opening to flow rate is a linear curve 2.Equal percentage: For ... At small opening the increments in flow rate is more. At higher opening the flow rate becomes steady.  

What is the use of link connected to the valve positioner ?

Description : What is the use of link connected to the valve positioner ?

Last Answer : The link serves as the feed back to the value. Ant valve movement is sensed by this link. Sometimes due to line pressure changes on H.P. service the valve position may be changed, the ... this change and the positioner will produce an output which will operate the valve to the original position.

What is a cage valve ?

Description : What is a cage valve ? 

Last Answer : A cage valve uses a piston with piston ring seal attached to the single seated valve "plug". Here the hydrostatic forces acting on the top or the piston or below the valve plug tend to cancel out. The seat ring is clamped in by a cage. Cage valves are generally used for noise reduction. 

What is the use of a valve positioner ?

Description : What is the use of a valve positioner ?

Last Answer : The valve positioner is used for following reasons : 1. Quick Action control valve. 2. Valve hysteresis. 3. Valves used on viscous liquids. 4. Split Range. 5. Line pressure changes on valve. 6. Valve Bench set not standard. 7. Reversing valve operation. 

What is the use of double seated valve ?

Description : What is the use of double seated valve ?

Last Answer : In double seated valves the upward and downward forces on the plug due to reduction of fluid pressure are nearly equalized. It is generally used on bigger size valves and high pressure systems. Actuator forces required are less i.e. A small size actuator. 

What is the use of single seated valve ?

Description : What is the use of single seated valve ?

Last Answer : The single seated valve is used on smaller sizes, and in valve of larger sizes, where an absolute shut off is required. The use of single seated valve is limited by pressure drop across the valve in the closed or almost closed position.  

What are the different types of control valves ?

Description : What are the different types of control valves ?  

Last Answer : The commonly used control valves can be divided as follows. 1. Depending on Action. 2. Depending on the Body. 1. Depending on action: Depending on action there are two types of control valves, (1) ... valves single or double seated. 2. Angle valves. 3. Butterfly valves. 4. Three way valves. 

What is a control valves ?

Description : What is a control valves ? 

Last Answer : A control valve is the final control element, which directly changes the valve of the manipulated variable by changing the rate of flow of control agent. A control valve consists of an operator and valve body. ... 3 psi on the diaphragm the value is closed and 15 psi air signal it in fully open.  

What is the use of Angle valves ?

Description : What is the use of Angle valves ?

Last Answer : Angle valves are used where very high pressure drops are required and under very severe conditions. Where the conventional type of valve would be damaged by erosion. 

What is the use of booster relays ?

Description : What is the use of booster relays ?  

Last Answer : Booster relays are essentially air load, self contained pressure regulators. They are classified into three broad groups :  1. Volume Boosters : These are used to multiply the available volume of ... 3. Reversing Relays : This produces a decreasing output signal for an increasing input  signal.

What are the advantages of Camflex valves ?

Description : What are the advantages of Camflex valves ?

Last Answer : Camflex valves are intermediates between globe valve and butterfly valve. The plug rotates 60' for full opening. Advantages: 1. Actuator forces required are very less. 2.Extended bonnet and hence can be used ... on high temp. and very low  Temperature. 3. Variations in flow. 4. Light weight.

What are the different types of plugs ?

Description : What are the different types of plugs ?

Last Answer : The different types of plugs are generally used are : ( 1 ) V. port plug ( 2 ) Contoured plug V-port plug: Ported plug are generally used on double seated valves. This is because ... balance area. Contoured plug: Contoured plugs are generally used on single seated valve with small trim sizes. 

What is the use of three way valves ?

Description : What is the use of three way valves ?

Last Answer : Three way control valves are only used on special systems, where a dividing or mixture of flows according to a controlled ratio is required.

What is the use of butterfly valves ?

Description : What is the use of butterfly valves ?

Last Answer : Butterfly valves are used only in systems where a small pressure drop across the valve is allowed. The butterfly is fully open when the disc rotates by 90. A drawback of this valve is that even a very small angular displacement produces a big change in flow.

When can a by pass be not used on a positioner ?

Description : When can a by pass be not used on a positioner ? 

Last Answer : A by pass on a positioner cannot be used when : 1. Split Range operation. 2. Reverse Acting Positioner. 3. Valve bench set not standard. 

What types of bonnets would you use of high temp. and very low temp. ?

Description : What types of bonnets would you use of high temp. and very low temp. ?

Last Answer : High temperature: Bonnets are provided with radiation fins to prevent glad packing from getting damaged.  On very low temperature: Extended bonnets are used to prevent gland packing from getting freezed

My Peugeot 106 is overrevving on initial start and when idle - is it the idle control valve or automatic choke?

Description : My Peugeot 106 is overrevving on initial start and when idle - is it the idle control valve or automatic choke?

Last Answer : If it doesn’t settle down when it warms up, it’s less likely to be the choke.

What PSI should the trailer Air Supply control valve close?

Description : What PSI should the trailer Air Supply control valve close?

Last Answer : No less than 30 psi

Where is the Idle Air Control Valve on a 2004 Buick rendezvous?

Description : Where is the Idle Air Control Valve on a 2004 Buick rendezvous?

Last Answer : Feel Free to Answer

As shown in the illustration, when the 'speed control' system is in 'SPLIT' _______________. EL-0096 A. Relays #1, #5 and #8 are not used B. the 'slew rated controller' is grounded through Relay #6 C. the RPM 'function generator' and 'thrust levers' have no control D. the 'E/P converters' are bypassed and air is fed directly to the governors via the 'load sharing valve'

Description : As shown in the illustration, when the 'speed control' system is in 'SPLIT' _______________. EL-0096 A. Relays #1, #5 and #8 are not used B. the 'slew rated controller' is grounded through Relay ... E/P converters' are bypassed and air is fed directly to the governors via the 'load sharing valve'

Last Answer : Answer: C

On an engine throttle control system, the auxiliary control circuits are provided with devices to prevent excessive overtravel of the pilot valve by the synchronous motor. These devices are called _________________. A. overlap sensors B. limit switches C. overtravel relays D. proximity switches

Description : On an engine throttle control system, the auxiliary control circuits are provided with devices to prevent excessive overtravel of the pilot valve by the synchronous motor. These devices are called _________________. A. overlap sensors B. limit switches C. overtravel relays D. proximity switches

Last Answer : Answer: B

Which of the following is used to control the speed variations of the engine caused by the fluctuations of the engine turning moment? 1. D-slide valve 2. Governor 3. Flywheel 4. Meyer’s expansion valve

Description : Which of the following is used to control the speed variations of the engine caused by the fluctuations of the engine turning moment? 1. D-slide valve 2. Governor 3. Flywheel 4. Meyer’s expansion valve

Last Answer : 3. Flywheel

The valve used to control the back flow of digesta from ventriculus to crop is C A. Mesentronic valve B. Proctodaeal valve C. Stomodaeal valve D. Atrial valve

Description : The valve used to control the back flow of digesta from ventriculus to crop is C A. Mesentronic valve B. Proctodaeal valve C. Stomodaeal valve D. Atrial valve

Last Answer : Stomodaeal valve

A globe valve is the most suitable for applications, in which (A) Fluid flow control is required (B) Fluid contains dispersed solid particles (C) Valve is required to be either fully open or fully closed (D) One way flow is required

Description : A globe valve is the most suitable for applications, in which (A) Fluid flow control is required (B) Fluid contains dispersed solid particles (C) Valve is required to be either fully open or fully closed (D) One way flow is required

Last Answer : (A) Fluid flow control is required

The most economical flow control valve for use with large diameter pipes is a (A) Butterfly valve (B) Globe valve (C) Needle valve (D) None of these

Description : The most economical flow control valve for use with large diameter pipes is a (A) Butterfly valve (B) Globe valve (C) Needle valve (D) None of these

Last Answer : (A) Butterfly valve

Foot valve provided in the pump is a __________ valve. (A) Direction control (B) Back pressure (C) Relief (D) Pressure reduction

Description : Foot valve provided in the pump is a __________ valve. (A) Direction control (B) Back pressure (C) Relief (D) Pressure reduction

Last Answer : (B) Back pressure

Remote control valve is a __________ valve. (A) Gate (B) Butterfly (C) Needle (D) Globe

Description : Remote control valve is a __________ valve. (A) Gate (B) Butterfly (C) Needle (D) Globe

Last Answer : (B) Butterfly

The valve used for very remote and accurate control of fluid is a __________ valve. (A) Needle (B) Globe (C) Gate (D) Butterfly

Description : The valve used for very remote and accurate control of fluid is a __________ valve. (A) Needle (B) Globe (C) Gate (D) Butterfly

Last Answer : (A) Needle

Check valve is used for __________ flow. (A) Very precise control of (B) Unidirectional (C) Multidirectional (D) None of these

Description : Check valve is used for __________ flow. (A) Very precise control of (B) Unidirectional (C) Multidirectional (D) None of these

Last Answer : (B) Unidirectional

A relief valve (A) Provides back pressure for a cylinder (B) Unloads a pump (C) Is a directional control valve (D) None of these

Description : A relief valve (A) Provides back pressure for a cylinder (B) Unloads a pump (C) Is a directional control valve (D) None of these

Last Answer : (C) Is a directional control valve

A hydraulic accumulator comprises of (A) A storage device and a control valve (B) A cylinder and a plunger (C) Two pistons and two cylinders (D) A storage tank and a ram pump

Description : A hydraulic accumulator comprises of (A) A storage device and a control valve (B) A cylinder and a plunger (C) Two pistons and two cylinders (D) A storage tank and a ram pump

Last Answer : (B) A cylinder and a plunger

Which of the following facilitates close control of flow of fluids? (A) Gate valve (B) Globe valve (C) Butterfly valve (D) Check valve

Description : Which of the following facilitates close control of flow of fluids? (A) Gate valve (B) Globe valve (C) Butterfly valve (D) Check valve

Last Answer : (B) Globe valve

Purpose of relief valve in a reciprocating pump is to (A) Protect the pump against developing excessive pressure (B) Facilitate unidirectional flow of liquid (C) Reduce the discharge pressure (D) Control the rate of discharge

Description : Purpose of relief valve in a reciprocating pump is to (A) Protect the pump against developing excessive pressure (B) Facilitate unidirectional flow of liquid (C) Reduce the discharge pressure (D) Control the rate of discharge

Last Answer : (A) Protect the pump against developing excessive pressure

Aerodynamic noise resulting from turbulent gas flow is the most prevalent source of valve noise in fluid flow control. It is caused due to (A) Reynold stresses (B) Shear forces (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Aerodynamic noise resulting from turbulent gas flow is the most prevalent source of valve noise in fluid flow control. It is caused due to (A) Reynold stresses (B) Shear forces (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Can We Use A Control Valve Without Positioner?

Description : Can We Use A Control Valve Without Positioner?

Last Answer : Control valve can not be without positioner. The purpose of the positioner is to control the control valve stroke so as to keep the valve in desired position. The positioner receives signal from ... the desired position the positioner cuts the boosted signal to the actuator and keeps the position.

Device to control the pressure of fluid and gases within range of settings. a. Relief valve. c. Filter b. Spray gun. d. Pressure regulator

Description : Device to control the pressure of fluid and gases within range of settings. a. Relief valve. c. Filter b. Spray gun. d. Pressure regulator

Last Answer : Pressure regulator

An operator tells you that a control valve in a stuck ? How will you start checking ?

Description : An operator tells you that a control valve in a stuck ? How will you start checking ?

Last Answer : 1. First of all get the control valve is passed from operation. 2. Check the lingual to the diaphragm of the control valve. 3. Disconnect it possible the actuator stem from the control valve stem. ٤. ... operates. If it does not then the control valve has to be removed from the line to w/shop. 

What are some common causes of control valve noise?

Description : What are some common causes of control valve noise?

Last Answer : If you have excessive pressure drop across the control valve and the downstream pressure is low enough to cause the liquid to flash, a great deal of noise in the control valve can result. Excessive ... the valve may have been designed correctly at the time, but is too large for current operation.

Explain working of Variable Valve Timing and Electronic lift control (VTEC) system. Enlist its advantage and Drawbacks

Description : Explain working of Variable Valve Timing and Electronic lift control (VTEC) system. Enlist its advantage and Drawbacks

Last Answer : Answer: Working of Variable Valve Timing and Electronic lift control (VTEC) system:- VTEC (which stands for Variable Valve Timing and Lift Electronic Control) is an electronic and mechanical system ... 2) Maintenance cost is high 3) Very complex structure required complicated control system.

Describe with neat sketch operation of PCV valve under different engine operating condition to control/ emission

Description : Describe with neat sketch operation of PCV valve under different engine operating condition to control/ emission

Last Answer : PCV Valve: It consists of a spring loaded tapered valve for flow control. The crankcase pressure and manifold vacuum act together to close the valve whereas the spring pressure tends to keep it open.( ... at idle and low speed (c)High speed/Load operation (d)Preventing backfire during cranking  

Explain the working of valve actuators used in control valve.

Description : Explain the working of valve actuators used in control valve.

Last Answer : Working of spring diaphragm actuator: Actuator is the portion of the valve that responds to the applied signal and results in the movement of the stem due to which the flow rate of fluid changes. ... input signal. The diaphragm is made of neoprene or any other synthetic elastic element.

State the factors to be considered for control valve selection.

Description : State the factors to be considered for control valve selection.

Last Answer : Factors to be considered for control valve selection: The basic steps in control valve selection are 1. The first step in control valve selection involves collecting all relevant data and completing the ... force or friction. A hand wheel is needed if manual operation of the valve is expected.

What is function of Oil reservoir,Pressure relief valve, Direction control valve and filters in Hydraulic system.

Description : What is function of Oil reservoir,Pressure relief valve,  Direction control valve and filters in Hydraulic system.

Last Answer : (i) Oil Reservoir - To store the Hydraulic oil for the circuit (ii) Pressure Relief Valve- To release the extra pressure whenever not required by system (iii) Direction Control Valve- To ... (iv) Filters- To filter the foreign particle from the oil and to separates submicron level contamination

In pneumatic control systems the control valve used as final control element converts

Description : In pneumatic control systems the control valve used as final control element converts 

Last Answer : In pneumatic control systems the control valve used as final control element converts pressure signal to position change.

change valve cover gasket on nissan pickup

Description : change valve cover gasket on nissan pickup

Last Answer : Need Answer