As the thermal noise get doubled due to the increase in a resistance the noise power get.

As the thermal noise get doubled due to the increase in a resistance the noise power get. 

(A) doubled (B) quadruped (C) unchanged (D) halved.
by

1 Answer

Answer :

As the thermal noise get doubled due to the increase in a resistance the noise power get. unchanged 

by

Related questions

The value of the resistor creating thermal noise is doubled. The noise power generated is therefore. A. halved B. quadrupled C. doubled D. unchanged

Description : The value of the resistor creating thermal noise is doubled. The noise power generated is therefore. A. halved B. quadrupled C. doubled D. unchanged

Last Answer : D. unchanged

Noise is primarily a variation in

Description : Noise is primarily a variation in (A) Amplitude (B) phase (C) frequency (D) none of the above

Last Answer : Noise is primarily a variation in Amplitude

Noise limiter is provided on AM receivers to

Last Answer : Noise limiter is provided on AM receivers to reduce interfering noise due to ignition system, reduce noise due to electrical storms, reduce interference due to electrical machinery.

In order to reduce quantizing noise, one must

Last Answer : In order to reduce quantizing noise, one must Increase the number of standard amplitudes.

The square of the thermal noise voltage generated by a resistor is proportional to A. its resistance B. its temperature C. the bandwidth over which it is measured D. All of the above

Description : The square of the thermal noise voltage generated by a resistor is proportional to A. its resistance B. its temperature C. the bandwidth over which it is measured D. All of the above

Last Answer : D. All of the above

Noise caused by the thermal agitation of electrons in resistance. A. All of these B. Thermal noise C. Johnson’s noise D. White noise

Description : Noise caused by the thermal agitation of electrons in resistance. A. All of these B. Thermal noise C. Johnson’s noise D. White noise

Last Answer : A. All of these

Crosstalk due to incomplete suppression of sidebands or to intermodulation of two or more frequency-multiplexed channels which is unintelligible is classified as A. Impulse noise B. Thermal noise C. Quantizing noise D. Miscellaneous noise

Description : Crosstalk due to incomplete suppression of sidebands or to intermodulation of two or more frequency-multiplexed channels which is unintelligible is classified as A. Impulse noise B. Thermal noise C. Quantizing noise D. Miscellaneous noise

Last Answer : D. Miscellaneous noise

The thermal noise is due to random

Last Answer : The thermal noise is due to random Motion of free electrons.

If the head is doubled in & centrifugal pump, the power required will increase in the ratio of (A) 23 (B) 23/2 (C) 25/2 (D) 21/3

Description : If the head is doubled in & centrifugal pump, the power required will increase in the ratio of (A) 23 (B) 23/2 (C) 25/2 (D) 21/3

Last Answer : B) 23/2

It is the thermal noise power normalized to 1- Hz bandwidth:

Description : It is the thermal noise power normalized to 1- Hz bandwidth:

Last Answer : noise power density

When a dipole antenna of 1/8 length has an equivalent total resistance of 1.5 Watt then the efficiency of the

Description : When a dipole antenna of 1/8 length has an equivalent total resistance of 1.5 Watt then the efficiency of the antenna is   (A) 0.89159% (B) 8.9159% (C) 89.159% (D) 891.59%

Last Answer : When a dipole antenna of 1/8 length has an equivalent total resistance of 1.5 Watt then the efficiency of the antenna is 89.159%

When an antenna of input resistance 73 ohm is connected to a 50-ohm line and if the losses are ignored then

Description : When an antenna of input resistance 73 ohm is connected to a 50-ohm line and if the losses are ignored then its efficiency will be nearly   (A) 0.19 (B) 0.81 (C) 0.97 (D) 1.19

Last Answer : When an antenna of input resistance 73 ohm is connected to a 50-ohm line and if the losses are ignored then its efficiency will be nearly 0.81

If the resistance total in a series circuit doubles, current will:

Last Answer : If the resistance total in a series circuit doubles, current will: be halved

The resistance of a silver wire at `0^(@)C " is " 1.25 Omega`. Upto what temperature it must be heated so that its resistance is doubled ? The tempera

Description : The resistance of a silver wire at `0^(@)C " is " 1.25 Omega`. Upto what temperature it must be heated so that its resistance is doubled ? The tempera

Last Answer : The resistance of a silver wire at `0^(@)C " is " 1.25 Omega`. Upto what temperature ... temperature be same for all silver conductors of all shapes ?

A metal wire of circular cross-section has a resistance `R_(1)`. The wire is now stretched without breaking, so that its length is doubled and the den

Description : A metal wire of circular cross-section has a resistance `R_(1)`. The wire is now stretched without breaking, so that its length is doubled and the den

Last Answer : A metal wire of circular cross-section has a resistance `R_(1)`. The wire is now stretched without breaking, so that its ... 2` C. `4 : 1` D. `1 : 4`

If the resistance of a circuit is cut in half and the applied voltage is kept constant, the current flow will be _____________. A. doubled B. quadrupled C. unchanged D. cut in half

Description : If the resistance of a circuit is cut in half and the applied voltage is kept constant, the current flow will be _____________. A. doubled B. quadrupled C. unchanged D. cut in half

Last Answer : Answer: A

If the length of a wire is halved and the cross-sectional area is doubled, the resistance will be _____________. A. quartered B. unchanged C. doubled D. quadrupled

Description : If the length of a wire is halved and the cross-sectional area is doubled, the resistance will be _____________. A. quartered B. unchanged C. doubled D. quadrupled

Last Answer : Answer: A

In a footstep bearing, if the radius of the shaft is doubled, then the torque required to overcome the viscous resistance will be (A) Double (B) Four times (C) Eight times (D) Sixteen times

Description : In a footstep bearing, if the radius of the shaft is doubled, then the torque required to overcome the viscous resistance will be (A) Double (B) Four times (C) Eight times (D) Sixteen times

Last Answer : Answer: Option D

In a footstep bearing, if the speed of the shaft is doubled, then the torque required to overcome the viscous resistance will be (A) Double (B) Four times (C) Eight times (D) Sixteen times

Description : In a footstep bearing, if the speed of the shaft is doubled, then the torque required to overcome the viscous resistance will be (A) Double (B) Four times (C) Eight times (D) Sixteen times

Last Answer : Answer: Option A

In a footstep bearing, if the speed of the shaft is doubled, then the torque required to overcome the viscous resistance will be (A) Double (B) Four times (C) Eight times (D) Sixteen times

Description : In a footstep bearing, if the speed of the shaft is doubled, then the torque required to overcome the viscous resistance will be (A) Double (B) Four times (C) Eight times (D) Sixteen times

Last Answer : Answer: Option A

A wire of uniform area of cross-section A length L and resistance R is cut into two parts. Resistivity of each part a. remains the same b. is doubled c. is halved d. becomes zero

Description : A wire of uniform area of cross-section A length L and resistance R is cut into two parts. Resistivity of each part a. remains the same b. is doubled c. is halved d. becomes zero

Last Answer : a. remains the same

If the diameter of a conductor of 10 ohms is doubled, its new resistance would be?

Description : If the diameter of a conductor of 10 ohms is doubled, its new resistance would be? A.20 ohms B.5 ohms C.40 ohms D.2.5 ohms

Last Answer : 4

What happens to the resistance of a wire when its length as well as the cross-sectional area are doubled?

Description : What happens to the resistance of a wire when its length as well as the cross-sectional area are doubled? A) It doubles B) It becomes 4 times C) It becomes 2π times D) It remains the same

Last Answer : Automatically the resistivity will increase as they are the factors affecting the resistivity 

A wire of resistance R has it length and cross-section both doubled. Its resistance will become

Last Answer : A wire of resistance R has it length and cross-section both doubled. Its resistance will become R.

If a wire conductor of 0.2 ohm resistance is doubled in length, its resistance becomes?

Description : If a wire conductor of 0.2 ohm resistance is doubled in length, its resistance becomes?

Last Answer : If a wire conductor of 0.2 ohm resistance is doubled in length, its resistance becomes 0.4 ohm.

When both the inductance and resistance of a coil are doubled the value of?

Description : When both the inductance and resistance of a coil are doubled the value of?

Last Answer : When both the inductance and resistance of a coil are doubled the value of time constant remains unchanged.

..................... is a type of transmission impairment in which the signal loses strength due to the resistance of the transmission medium. (A) Attenuation (B) Distortion (C) Noise (D) Decibel

Description : ..................... is a type of transmission impairment in which the signal loses strength due to the resistance of the transmission medium. (A) Attenuation (B) Distortion (C) Noise (D) Decibel

Last Answer : (A) Attenuation

At room temperature the current in an intrinsic semiconductor is due to

Last Answer : At room temperature, the current in an intrinsic semiconductor is due to holes and electrons.

Diversity reception system is used to minimize the troubles due to

Last Answer : Diversity reception system is used to minimize the troubles due to General fading, Synchronous fading.

Presence of a non-condensing gas in a condensing vapour (A) Increases the rate of condensation (B) Decreases thermal resistance (C) Is desirable to increase the film co-efficient (D) None of these

Description : Presence of a non-condensing gas in a condensing vapour (A) Increases the rate of condensation (B) Decreases thermal resistance (C) Is desirable to increase the film co-efficient (D) None of these

Last Answer : (D) None of these

reduction in thermal resistance during heat transfer does not occur in the (A) Convection heat transfer by stirring the fluid and cleaning the heating surface (B) Conduction heat transfer by reduction in the material thickness and increase in the thermal conductivity (C) Radiation heat transfer by increasing the temperature and reducing the emissivity (D) None of these

Description : reduction in thermal resistance during heat transfer does not occur in the (A) Convection heat transfer by stirring the fluid and cleaning the heating surface (B) Conduction heat transfer by ... Radiation heat transfer by increasing the temperature and reducing the emissivity (D) None of these

Last Answer : Option C

Pick up the correct statement from the following: (A) Catalysts are added to assist and accelerate the hardening of resin (B) The fillers are inert materials and they impart strength and hardness (C) Fibrous fillers increase thermal resistance (D) All the above

Description : Pick up the correct statement from the following: (A) Catalysts are added to assist and accelerate the hardening of resin (B) The fillers are inert materials and they impart strength and hardness (C) Fibrous fillers increase thermal resistance (D) All the above

Last Answer : Answer: Option D

The percentage increase in the area of a triangle if each of its side is doubled is -Maths 9th

Description : The percentage increase in the area of a triangle if each of its side is doubled is -Maths 9th

Last Answer : (c) 300%.Let a, b, c be the sides of the original triangle and s be its semi-perimeter.Then, s = \(rac{1}{2}\)(a+b+c)Let s1 be the semi-perimeter of the new triangle. Then,s1 = \(rac{1}{2}\) (2a + 2b ... increase in area = \(\bigg(rac{A_1-A}{A} imes100\bigg)\)%= \(rac{(4A-A)}{A} imes100\)% = 300%.

When distance from center is doubled then electric field strength will A. decrease by the factor of four B. increase by factor of four C. will be same D. decrease by factor of two

Description : When distance from center is doubled then electric field strength will A. decrease by the factor of four B. increase by factor of four C. will be same D. decrease by factor of two

Last Answer :  decrease by the factor of four

If the head over the triangular notch is doubled, the discharge will increase by __________ times. (A) 2 (B) 2.828 (C) 5.657 (D) 4

Description : If the head over the triangular notch is doubled, the discharge will increase by __________ times. (A) 2 (B) 2.828 (C) 5.657 (D) 4

Last Answer : (C) 5.657

For laminar flow of a shear thinning liquid in a pipe, if the volumetric flow rate is doubled, the pressure gradient will increase by a factor of (A) 2 (B) < 2 (C) > 2 (D) 1/2

Description : For laminar flow of a shear thinning liquid in a pipe, if the volumetric flow rate is doubled, the pressure gradient will increase by a factor of (A) 2 (B) < 2 (C) > 2 (D) 1/2

Last Answer : (A) 2

The rate of a chemical reaction is almost doubled for every 10°C rise in temperature. The rate will increase __________ times, if the temperature rises from 10 to 100°C. (A) 256 (B) 512 (C) 112 (D) 612

Description : The rate of a chemical reaction is almost doubled for every 10°C rise in temperature. The rate will increase __________ times, if the temperature rises from 10 to 100°C. (A) 256 (B) 512 (C) 112 (D) 612

Last Answer : (B) 512

If the length of a cantilever carrying an isolated load at its free end is doubled, the deflection of the free end will increase by (A) 8 (B) 1/8 (C) 1/3 (D) 2

Description : If the length of a cantilever carrying an isolated load at its free end is doubled, the deflection of the free end will increase by (A) 8 (B) 1/8 (C) 1/3 (D) 2

Last Answer : (B) 1/8

Which of the following methods cannot be used to increase the bandwidth for cascaded RF amplifier stages? A) Wave traps in each stage B) Stagger tuning C) A shunt damping resistor across each tuned circuit D) Doubled tuned transformers with tighter coupling

Description : Which of the following methods cannot be used to increase the bandwidth for cascaded RF amplifier stages? A) Wave traps in each stage B) Stagger tuning C) A shunt damping resistor across each tuned circuit D) Doubled tuned transformers with tighter coupling

Last Answer : A) Wave traps in each stage

What would happen if gravity suddenly doubled on Earth, but the mass of the atmosphere did not change? (a) Surface pressure would stay the same but the density would increase. (b) Surface pressure would increase but the density would stay the same. (c) Surface pressure and density would both increase. (d) Surface density and pressure would stay the same because the atmosphere is in hydrostatic balance.

Description : What would happen if gravity suddenly doubled on Earth, but the mass of the atmosphere did not change? (a) Surface pressure would stay the same but the density would increase. (b) Surface ... (d) Surface density and pressure would stay the same because the atmosphere is in hydrostatic balance.

Last Answer : Surface pressure and density would both increase.

If depth of a beam is doubled then changes in its section modulus a. Will remain same b. Will decrease c. Will be doubled d. Will increase by 4 times

Description : If depth of a beam is doubled then changes in its section modulus a. Will remain same b. Will decrease c. Will be doubled d. Will increase by 4 times

Last Answer : d. Will increase by 4 times

When the speed of a train moving on a circular track is doubled, the centripetal force acting on the train does one of the following. Does the force: w) remain the same x) increase by a factor of 2 y) increase by a factor of 4 z) increase by a factor of 8

Description : When the speed of a train moving on a circular track is doubled, the centripetal force acting on the train does one of the following. Does the force: w) remain the same x) increase by a factor of 2 y) increase by a factor of 4 z) increase by a factor of 8

Last Answer : ANSWER: Y -- INCREASE BY A FACTOR OF 4

How do industries create thermal and noise pollution ? -SST 10th

Description : How do industries create thermal and noise pollution ? -SST 10th

Last Answer : Hot water from factories when is allowed to flow into rivers and ponds is caused thermal pollution. Thermal pollution would affect on aquatic life greatly. Industrial and constructional ... machineries create unwanted sound of intolerable nature which impaired human ears and nervous breakdown.

How do industries create thermal and noise pollution ? -SST 10th

Description : How do industries create thermal and noise pollution ? -SST 10th

Last Answer : Hot water from factories when is allowed to flow into rivers and ponds is caused thermal pollution.

Electrostatic precipitator is used to control the pollution of – (1) air (2) water (3) noise (4) thermal

Description : Electrostatic precipitator is used to control the pollution of – (1) air (2) water (3) noise (4) thermal

Last Answer : (1) air Explanation: An electrostatic precipitator (ESP), or electrostatic air cleaner is a particulate collection device that removes particles from a flowing gas (such as air) using the force of an ... particles from a flowing gas (such as air) using the force of an induced electrostatic charge.

A noise whose source is within the solar system. A. Solar noise B. Thermal noise C. Cosmic noise D. Johnson Noise

Description : A noise whose source is within the solar system. A. Solar noise B. Thermal noise C. Cosmic noise D. Johnson Noise

Last Answer : A. Solar noise

External noise originating outside the solar system A. Cosmic noise B. Solar noise C. Thermal noise D. Lunar noise

Description : External noise originating outside the solar system A. Cosmic noise B. Solar noise C. Thermal noise D. Lunar noise

Last Answer : A. Cosmic noise

Noise occurring in the presence of signal resulting from a mismatch between the exact value of an analog signal and the closet available quantizing step in a digital coder. A. Quantizing noise B. Thermal noise C. Impulse noise D. Crosstalk

Description : Noise occurring in the presence of signal resulting from a mismatch between the exact value of an analog signal and the closet available quantizing step in a digital coder. A. Quantizing noise B. Thermal noise C. Impulse noise D. Crosstalk

Last Answer : A. Quantizing noise

Most internal noise comes from A. Shot noise B. Transit-time noise C. Thermal agitation D. Skin effect

Description : Most internal noise comes from A. Shot noise B. Transit-time noise C. Thermal agitation D. Skin effect

Last Answer : C. Thermal agitation