Concrete is [ A ] Weak in tension [ B ] Strong in tension [ C ] Strong in both tension and compression [ D ] Weak in compression

Concrete is
[ A ] Weak in tension
[ B ] Strong in tension
[ C ] Strong in both tension and compression
[ D ] Weak in compression
by

1 Answer

Answer :

[ A ] Weak in tension
by

Related questions

Pick up the correct statement from the following: (A) Plain cement concrete is equally strong in compression as well as in tension (B) Slump test is performed to check concrete strength (C) Curing of concrete is done for proper compaction of cement (D) Fineness modulus is the index number expressing the relative sizes of both coarse and fine aggregates

Description : Pick up the correct statement from the following: (A) Plain cement concrete is equally strong in compression as well as in tension (B) Slump test is performed to check concrete strength (C ... D) Fineness modulus is the index number expressing the relative sizes of both coarse and fine aggregates

Last Answer : Option D

In pre-stressed concrete (A) Forces of tension and compression change but lever arm remains unchanged (B) Forces of tension and compressions remain unchanged but lever arm changes with the moment (C) Both forces of tension and compression as well as lever arm change (D) Both forces of tension and compression as well as lever arm remain unchanged

Description : In pre-stressed concrete (A) Forces of tension and compression change but lever arm remains unchanged (B) Forces of tension and compressions remain unchanged but lever arm changes with the moment ( ... arm change (D) Both forces of tension and compression as well as lever arm remain unchanged

Last Answer : Answer: Option B

In a singly reinforced concrete beam, as the load increases. (a) Only concrete will resist tension (b) Only steel bars will resist tension. (c) Both concrete and steel will resist tension. (d) Both concrete and steel will resist compression.

Description : In a singly reinforced concrete beam, as the load increases. (a) Only concrete will resist tension (b) Only steel bars will resist tension. (c) Both concrete and steel will resist tension. (d) Both concrete and steel will resist compression.

Last Answer : (b) Only steel bars will resist tension.

In a singly reinforced concrete beam, if the load is vey small. (a) Only concrete will resist tension (b) Only steel bars will resist tension. (c) Both concrete & steel will resist tension. (d) Both concrete & steel will resist compression.

Description : In a singly reinforced concrete beam, if the load is vey small. (a) Only concrete will resist tension (b) Only steel bars will resist tension. (c) Both concrete & steel will resist tension. (d) Both concrete & steel will resist compression.

Last Answer : (c) Both concrete & steel will resist tension.

Due to Bleeding action concrete becomes [ A ] Weak [ B ] Strong [ C ] Hard [ D ] Durable

Description : Due to Bleeding action concrete becomes [ A ] Weak [ B ] Strong [ C ] Hard [ D ] Durable

Last Answer : [ A ] Weak

The section of a reinforced beam where most distant concrete fibre in compression and tension in steel attains permissible stresses simultaneously, is called (A) Balanced sectionB) Economic section (C) Critical section (D) All the above

Description : The section of a reinforced beam where most distant concrete fibre in compression and tension in steel attains permissible stresses simultaneously, is called (A) Balanced section B) Economic section (C) Critical section (D) All the above

Last Answer : Answer: Option D

Shear resistance of concrete in a reinforced concrete beam is dependent on (a) Tension reinforcement in the beam (b) Compression reinforcement in the beam (c ) Shear reinforcement in the beam (d) None of the reinforcements in the beam

Description : Shear resistance of concrete in a reinforced concrete beam is dependent on (a) Tension reinforcement in the beam (b) Compression reinforcement in the beam (c ) Shear reinforcement in the beam (d) None of the reinforcements in the beam

Last Answer : (a) Tension reinforcement in the beam

The base of a column is subjected to moment. If the intensity of bearing pressure due to axial load is equal to stress due to moment, then the bearing pressure between the base and the concrete is (a) Uniform compression throughout (b) Zero at one end and compression at the other end (c) Tension at one end and compression at the other end (d) Compression, verying as a parabolic profile

Description : The base of a column is subjected to moment. If the intensity of bearing pressure due to axial load is equal to stress due to moment, then the bearing pressure between the base and the concrete ... Tension at one end and compression at the other end (d) Compression, verying as a parabolic profile

Last Answer : (b) Zero at one end and compression at the other end

The equilibrium equation for the condition that tension will be equal to the compression is given by [ A ] Compression in concrete = Tension in steel [ B ] Compression in concrete + Compression in steel = Tension in steel [ C ] Compression in concrete = Compression in steel [ D ] None of the above

Description : The equilibrium equation for the condition that tension will be equal to the compression is given by [ A ] Compression in concrete = Tension in steel [ B ] Compression in concrete + Compression in steel = Tension in steel [ C ] Compression in concrete = Compression in steel [ D ] None of the above

Last Answer : [ B ] Compression in concrete + Compression in steel = Tension in steel

Select the incorrect statement from the following In eccentrically loaded columns, [ A ] The tensile strength of concrete is ignored [ B ] Design stress – strain curve for steel in compression is the same as in tension [ C ] The strain at different points in the section will be same [ D ] Plane section remain plane even after bending

Description : Select the incorrect statement from the following In eccentrically loaded columns, [ A ] The tensile strength of concrete is ignored [ B ] Design stress - strain curve for steel in compression is the ... different points in the section will be same [ D ] Plane section remain plane even after bending

Last Answer : [ C ] The strain at different points in the section will be same

Flanged beams are preferred when the concrete in the slab is on the [ A ] compression side of the beam [ B ] tension side of the beam [ C ] may be compression side or tension side of the beam [ D ] none of the above

Description : Flanged beams are preferred when the concrete in the slab is on the [ A ] compression side of the beam [ B ] tension side of the beam [ C ] may be compression side or tension side of the beam [ D ] none of the above

Last Answer : [ A ] compression side of the beam

Flanged beams are preferred when the concrete in the slab is on the [ A ] compression side of the beam [ B ] tension side of the beam [ C ] may be compression side or tension side of the beam [ D ] none of the above

Description : Flanged beams are preferred when the concrete in the slab is on the [ A ] compression side of the beam [ B ] tension side of the beam [ C ] may be compression side or tension side of the beam [ D ] none of the above

Last Answer : [ A ] compression side of the beam

A concrete block subjected to shear stresses, then the failure may result by [ A ] Diagonal tension [ B ] Longitudinal tension [ C ] Diagonal compression [ D ] None of the above

Description : A concrete block subjected to shear stresses, then the failure may result by [ A ] Diagonal tension [ B ] Longitudinal tension [ C ] Diagonal compression [ D ] None of the above

Last Answer : [ A ] Diagonal tension

The section of a reinforced beam where most distant concrete fiber in compression and tension in steel attains permissible stresses simultaneously is called (i)Balanced section (ii)Economic section (iii)Critical section [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Description : The section of a reinforced beam where most distant concrete fiber in compression and tension in steel attains permissible stresses simultaneously is called (i)Balanced section (ii)Economic section (iii)Critical section [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Last Answer : [ D ] i, ii and iii

Which of the following is NOT a characteristic of glass ionomer cements? a. strong in compression but weaker in tension True b. the matrix is formed during the initial set of the cement c. sets via an ion exchange reaction that continues for at least 24 hours true d. suitable for use as a core build up material in anterior teeth

Description : Which of the following is NOT a characteristic of glass ionomer cements? a. strong in compression but weaker in tension True b. the matrix is formed during the initial set of the cement c. sets via ... for at least 24 hours true d. suitable for use as a core build up material in anterior teeth

Last Answer : d. suitable for use as a core build up material in anterior teeth

The force which develops in a pressure conduit supported on trestles, is (A) Tension (B) Compression (C) Temperature stress (D) Flexural stress

Description : The force which develops in a pressure conduit supported on trestles, is  (A) Tension  (B) Compression  (C) Temperature stress  (D) Flexural stress

Last Answer : (D) Flexural stress

The assumption in the theory of bending of beams is: (A) Material is homogeneous (B) Material is isotropic (C) Young's modulus is same in tension as well as in compression (D) All the above

Description : The assumption in the theory of bending of beams is:  (A) Material is homogeneous  (B) Material is isotropic  (C) Young's modulus is same in tension as well as in compression  (D) All the above 

Last Answer : (D) All the above 

When a load crosses a through type Pratt truss in the direction left to right, the nature of force in any diagonal member in the left half of the span would (A) Change from compression to tension (B) Change from tension to compression (C) Always be compression (D) Always be tension

Description : When a load crosses a through type Pratt truss in the direction left to right, the nature of force in any diagonal member in the left half of the span would (A) Change from compression to tension (B) Change from tension to compression (C) Always be compression (D) Always be tension

Last Answer : (A) Change from compression to tension

The possible loading in various members of framed structures are (A) Compression or tension (B) Buckling or shear (C) Shear or tension (D) All of the above

Description : The possible loading in various members of framed structures are  (A) Compression or tension  (B) Buckling or shear  (C) Shear or tension  (D) All of the above 

Last Answer : (A) Compression or tension

As compared to uniaxial tension or compression, the strain energy stored in bending is only (A) 1/8 (B) 1/4 (C) 1/3 (D) 1/2

Description : As compared to uniaxial tension or compression, the strain energy stored in bending is only  (A) 1/8  (B) 1/4  (C) 1/3  (D) 1/2 

Last Answer : (C) 1/3 

Pick up the correct assumption of the theory of simple bending (A) The value of the Young's modulus is the same in tension as well as in compression (B) Transverse section of a beam remains plane before and after bending (C) The material of the beam is homogeneous and isotropic (D) All the above

Description : Pick up the correct assumption of the theory of simple bending  (A) The value of the Young's modulus is the same in tension as well as in compression  (B) Transverse section of a beam remains ... bending  (C) The material of the beam is homogeneous and isotropic  (D) All the above

Last Answer : (D) All the above

The shear reinforcement in R.C.C. is provided to resist (A) Vertical shear (B) Horizontal shear (C) Diagonal compression (D) Diagonal tension

Description : The shear reinforcement in R.C.C. is provided to resist (A) Vertical shear (B) Horizontal shear (C) Diagonal compression (D) Diagonal tension

Last Answer : Answer: Option D

According to the steel beam theory of doubly reinforced beams (A) Tension is resisted by tension steel (B) Compression is resisted by compression steel (C) Stress in tension steel equals the stress in compression steel (D) All the above

Description : According to the steel beam theory of doubly reinforced beams (A) Tension is resisted by tension steel (B) Compression is resisted by compression steel (C) Stress in tension steel equals the stress in compression steel (D) All the above

Last Answer : Answer: Option D

The average permissible stress in bond for plain bars in tension is (A) Increased by 10% for bars in compression (B) Increased by 25% for bars in compression (C) Decreased by 10% for bars in compression (D) Decreased by 25% for bars in compression

Description : The average permissible stress in bond for plain bars in tension is (A) Increased by 10% for bars in compression (B) Increased by 25% for bars in compression (C) Decreased by 10% for bars in compression (D) Decreased by 25% for bars in compression

Last Answer : Answer: Option B

A fire hose has a nozzle attached to it, and the nozzle discharges a jet of water into the atmosphere at a velocity of 20 m/s. this causes the joint of the nozzle with the hose to be in : (a) Tension (b) A state of zero stress (c) Compression (d) Bending stress

Description : A fire hose has a nozzle attached to it, and the nozzle discharges a jet of water into the atmosphere at a velocity of 20 m/s. this causes the joint of the nozzle with the hose to be in : (a) Tension (b) A state of zero stress (c) Compression (d) Bending stress

Last Answer : (a) Tension

When the distance between centers of two adjacent rivets connecting the members subjected to either compression or tension exceeds the maximum pitch, then the additional rivets which are not subjected to the calculated stresses are known as (a) Packing rivets (b) Long-grip rivets (c) Tacking rivets (d) Auxiliary rivets

Description : When the distance between centers of two adjacent rivets connecting the members subjected to either compression or tension exceeds the maximum pitch, then the additional rivets which are not subjected to the ... (a) Packing rivets (b) Long-grip rivets (c) Tacking rivets (d) Auxiliary rivets

Last Answer : (c) Tacking rivets

Development length is the length or extension that should be provided on either side from the [ A ] face of the support [ B ] point of maximum tension [ C ] point of maximum compression [ D ] point of minimum compression

Description : Development length is the length or extension that should be provided on either side from the [ A ] face of the support [ B ] point of maximum tension [ C ] point of maximum compression [ D ] point of minimum compression

Last Answer : [ B ] point of maximum tension

Design yield stress for steel in tension and compression is [ A ] 0.65 fy [ B ] 0.87 fy [ C ] 0.75 fy [ D ] None of the above

Description : Design yield stress for steel in tension and compression is [ A ] 0.65 fy [ B ] 0.87 fy [ C ] 0.75 fy [ D ] None of the above

Last Answer : [ B ] 0.87 fy

Development length is the length or extension that should be provided on either side from the [ A ] face of the support [ B ] point of maximum tension [ C ] point of maximum compression [ D ] point of minimum compression

Description : Development length is the length or extension that should be provided on either side from the [ A ] face of the support [ B ] point of maximum tension [ C ] point of maximum compression [ D ] point of minimum compression

Last Answer : [ B ] point of maximum tension

Design yield stress for steel in tension and compression is [ A ] 0.65 fy [ B ] 0.87 fy [ C ] 0.75 fy [ D ] None of the above

Description : Design yield stress for steel in tension and compression is [ A ] 0.65 fy [ B ] 0.87 fy [ C ] 0.75 fy [ D ] None of the above

Last Answer : [ B ] 0.87 fy

The bond stress for plain bars in compression is more than that for bars in tension by [ A ] 25% [ B ] 40% [ C ] 60% [ D ] 50%

Description : The bond stress for plain bars in compression is more than that for bars in tension by [ A ] 25% [ B ] 40% [ C ] 60% [ D ] 50%

Last Answer : [ A ] 25%

Why are vacuum tubes also called valves? A) Because they can amplify the weak signals and make them strong B) Because they can stop or allow the flow of current C) Both of above D) None of above

Description : Why are vacuum tubes also called valves? A) Because they can amplify the weak signals and make them strong B) Because they can stop or allow the flow of current C) Both of above D) None of above

Last Answer : Answer : B

Each hydrogen bond is quite (A) Weak (B) Strong (C) Both (A) and (B) (D) None of these

Description : Each hydrogen bond is quite (A) Weak (B) Strong (C) Both (A) and (B) (D) None of these

Last Answer : Answer : A

Theories of elastic failure help to recognize (a) Weak materials (b) Strong materials (c) Both weak and strong materials (d) None

Description : Theories of elastic failure help to recognize (a) Weak materials (b) Strong materials (c) Both weak and strong materials (d) None

Last Answer : (c) Both weak and strong materials

. Highly caking coals (A) Produce weak coke (B) Produce strong coke (C) May damage the coke oven walls during carbonisation (D) Both (B) and (C)

Description : . Highly caking coals (A) Produce weak coke (B) Produce strong coke (C) May damage the coke oven walls during carbonisation (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

In carrying out compression test for concrete, should test cubes or test cylinders be adopted?

Description : In carrying out compression test for concrete, should test cubes or test cylinders be adopted?

Last Answer : Basically, the results of compression test carried out by using cubes are higher than that by cylinders. In compression test, the failure mode is in the form of tensile splitting induced by uniaxial ... are lower than that of cubes. Reference is made to Longman Scientific and Technical (1987).

If concrete compression test fails, should Schmidt hammer test be adopted as an alternative test to prove the concrete strength?

Description : If concrete compression test fails, should Schmidt hammer test be adopted as an alternative test to prove the concrete strength?

Last Answer : The Scmidt hammer test is based on the elastic rebound of hammer which presses on concrete surface and it measures the surface hardness of concrete. Since the test is very sensitive to the ... strength of concrete. Therefore, it may not be considered a good substitute for concrete compression test.

In concrete compression test, normally 150mmx150mmx150mm concrete cube samples is used for testing. Why isn’t 100mmx100mmx100mm concrete cube samples used in the test instead of 150mmx150mmx150mm concrete cube samples?

Description : In concrete compression test, normally 150mmx150mmx150mm concrete cube samples is used for testing. Why isn’t 100mmx100mmx100mm concrete cube samples used in the test instead of 150mmx150mmx150mm concrete cube samples?

Last Answer : Basically, the force supplied by a concrete compression machine is a definite value. For normal concrete strength application, say below 50MPa, the stress produced by a ... cube size of 150mmx150mmx150mm is already sufficient for the crushing strength of the machine.

In a singly reinforced beam (A) Compression is borne entirely by concrete (B) Steel possesses initial stresses when embedded in concrete (C) Plane sections transverse to the centre line of the beam before bending remain plane after bending (D) Elastic moduli for concrete and steel have different values within the limits of deformation of the beam

Description : In a singly reinforced beam (A) Compression is borne entirely by concrete (B) Steel possesses initial stresses when embedded in concrete (C) Plane sections transverse to the centre line ... Elastic moduli for concrete and steel have different values within the limits of deformation of the beam

Last Answer : Answer: Option C

When load is applied on concrete pavement (A) Away from edges, the maximum bending moment is negative (B) Away from edges, the maximum bending moment cause compression (C) On the edges, the maximum stress is parallel to the edge of the slab (D) None of these

Description : When load is applied on concrete pavement (A) Away from edges, the maximum bending moment is negative (B) Away from edges, the maximum bending moment cause compression (C) On the edges, the maximum stress is parallel to the edge of the slab (D) None of these

Last Answer : Answer: Option C

The compression in concrete (fc) at failure is given by [ A ] 0.30 fck [ B ] 0.45 fck [ C ] 0.50 fck [ D ] 0.75 fck

Description : The compression in concrete (fc) at failure is given by [ A ] 0.30 fck [ B ] 0.45 fck [ C ] 0.50 fck [ D ] 0.75 fck

Last Answer : [ B ] 0.45 fck

The concrete is assumed to reach failure with a compression strain of [ A ] 0.002 [ B ] 0.0035 [ C ] 0.0045 [ D ] 0.006

Description : The concrete is assumed to reach failure with a compression strain of [ A ] 0.002 [ B ] 0.0035 [ C ] 0.0045 [ D ] 0.006

Last Answer : [ B ] 0.0035

The stress-strain curve concrete in compression follows [ A ] a straight line [ B ] a rectangular parabolic curve [ C ] a semi circular arc [ D ] a cubic parabola

Description : The stress-strain curve concrete in compression follows [ A ] a straight line [ B ] a rectangular parabolic curve [ C ] a semi circular arc [ D ] a cubic parabola

Last Answer : [ B ] a rectangular parabolic curve

The concrete is assumed to reach failure with a compression strain of [ A ] 0.002 [ B ] 0.0035 [ C ] 0.0045 [ D ] 0.006

Description : The concrete is assumed to reach failure with a compression strain of [ A ] 0.002 [ B ] 0.0035 [ C ] 0.0045 [ D ] 0.006

Last Answer : [ B ] 0.0035

The stress-strain curve concrete in compression follows [ A ] a straight line [ B ] a rectangular parabolic curve [ C ] a semi circular arc [ D ] a cubic parabola

Description : The stress-strain curve concrete in compression follows [ A ] a straight line [ B ] a rectangular parabolic curve [ C ] a semi circular arc [ D ] a cubic parabola

Last Answer : [ B ] a rectangular parabolic curve

If permissible working stresses in steel and concrete are respectively 1400 kg/cm2 and 80 kg/cm2 and modular ratio is 18, in a beam reinforced in tension side and of width 30 cm and having effective depth 46 cm, the lever arms of the section, is (A) 37 cm (B) 38 cm (C) 39 cm (D) 40 cm

Description : If permissible working stresses in steel and concrete are respectively 1400 kg/cm2 and 80 kg/cm2 and modular ratio is 18, in a beam reinforced in tension side and of width 30 cm and having effective depth 46 cm, the lever arms of the section, is (A) 37 cm (B) 38 cm (C) 39 cm (D) 40 cm

Last Answer : Answer: Option D

A reinforced concrete cantilever beam is 3.6 m long, 25 cm wide and has its lever arm 40 cm. It carries a load of 1200 kg at its free end and vertical stirrups can carry 1800 kg. Assuming concrete to carry one-third of the diagonal tension and ignoring the weight of the beam, the number of shear stirrups required, is (A) 30 (B) 35 (C) 40 (D) 45

Description : A reinforced concrete cantilever beam is 3.6 m long, 25 cm wide and has its lever arm 40 cm. It carries a load of 1200 kg at its free end and vertical stirrups can carry 1800 kg. Assuming concrete to carry one- ... beam, the number of shear stirrups required, is (A) 30 (B) 35 (C) 40 (D) 45

Last Answer : Answer: Option C

If the permissible stress in steel in tension is 140 N/mm², then the depth of neutral axis for a singly reinforced rectangular balanced section will be (A) 0.35 d (B) 0.40 d (C) 0.45 d (D) Dependent on grade of concrete also

Description : If the permissible stress in steel in tension is 140 N/mm², then the depth of neutral axis for a singly reinforced rectangular balanced section will be (A) 0.35 d (B) 0.40 d (C) 0.45 d (D) Dependent on grade of concrete also

Last Answer : Answer: Option B

The type of aggregates not suitable for high strength concrete and for pavements subjected to tension, is (A) Rounded aggregate (B) Irregular aggregate (C) Angular aggregate (D) Flaky aggregat

Description : The type of aggregates not suitable for high strength concrete and for pavements subjected to tension, is (A) Rounded aggregate (B) Irregular aggregate (C) Angular aggregate (D) Flaky aggregat

Last Answer : Answer: Option A

Regarding the working stress design of under reinforced concrete section, (a) The neutral axis depth will be greater than that of a balanced section. (b) The stress in steel intension will reach its maximum permissible value first. (c) The moment of resistance will be less than that of the balanced section. (d) The concrete on the tension side is also be considered for calculating the moment of resistance of the section.

Description : Regarding the working stress design of under reinforced concrete section, (a) The neutral axis depth will be greater than that of a balanced section. (b) The stress in steel intension will reach ... on the tension side is also be considered for calculating the moment of resistance of the section.

Last Answer : both b&c