Working stress method of design results in -------------- percentages of compression steel than that of a limit state method of design [ A ] Equal [ B ] Larger [ C ] Smaller [ D ] Half of the

Working stress method of design results in -------------- percentages of compression steel than that of a limit state method of design
[ A ] Equal
[ B ] Larger
[ C ] Smaller
[ D ] Half of the
by

1 Answer

Answer :

[ B ] Larger
by

Related questions

In general in the design of a section by limit method, it is assumed that [ A ] the stress in steel to reach its yield limit before concrete failure [ B ] the stress in concrete to reach its permissible limit before to reach yield stress in steel [ C ] stresses in both concrete and steel reach their permissible values simultaneously [ D ] none of the above are correct

Description : In general in the design of a section by limit method, it is assumed that [ A ] the stress in steel to reach its yield limit before concrete failure [ B ] the stress in concrete to ... in both concrete and steel reach their permissible values simultaneously [ D ] none of the above are correct

Last Answer : [ A ] the stress in steel to reach its yield limit before concrete failure

In general in the design of a section by limit method, it is assumed that [ A ] the stress in steel to reach its yield limit before concrete failure [ B ] the stress in concrete to reach its permissible limit before to reach yield stress in steel [ C ] stresses in both concrete and steel reach their permissible values simultaneously [ D ] none of the above are correct

Description : In general in the design of a section by limit method, it is assumed that [ A ] the stress in steel to reach its yield limit before concrete failure [ B ] the stress in concrete to ... in both concrete and steel reach their permissible values simultaneously [ D ] none of the above are correct

Last Answer : [ A ] the stress in steel to reach its yield limit before concrete failure

In working stress method of design, the factor of safety for concrete and steel respectively are [ A ] 3.0 and 1.8 [ B ] 3.0 and 1.18 [ C ] 3.0 and 1.15 [ D ] 1.5 and 1.5

Description : In working stress method of design, the factor of safety for concrete and steel respectively are [ A ] 3.0 and 1.8 [ B ] 3.0 and 1.18 [ C ] 3.0 and 1.15 [ D ] 1.5 and 1.5

Last Answer : [ A ] 3.0 and 1.8

Select the incorrect statement from the following In eccentrically loaded columns, [ A ] The tensile strength of concrete is ignored [ B ] Design stress – strain curve for steel in compression is the same as in tension [ C ] The strain at different points in the section will be same [ D ] Plane section remain plane even after bending

Description : Select the incorrect statement from the following In eccentrically loaded columns, [ A ] The tensile strength of concrete is ignored [ B ] Design stress - strain curve for steel in compression is the ... different points in the section will be same [ D ] Plane section remain plane even after bending

Last Answer : [ C ] The strain at different points in the section will be same

Design yield stress for steel in tension and compression is [ A ] 0.65 fy [ B ] 0.87 fy [ C ] 0.75 fy [ D ] None of the above

Description : Design yield stress for steel in tension and compression is [ A ] 0.65 fy [ B ] 0.87 fy [ C ] 0.75 fy [ D ] None of the above

Last Answer : [ B ] 0.87 fy

Design yield stress for steel in tension and compression is [ A ] 0.65 fy [ B ] 0.87 fy [ C ] 0.75 fy [ D ] None of the above

Description : Design yield stress for steel in tension and compression is [ A ] 0.65 fy [ B ] 0.87 fy [ C ] 0.75 fy [ D ] None of the above

Last Answer : [ B ] 0.87 fy

In a limit state method of design, when shear reinforcement is not provided, the calculated shear stress at the critical section of a slab shall not exceed; [ A ] Ks 0.25 v fck [ B ] ks 0.20 v fck [ C ] ks 0.16 v fck [ D ] ks 0.10 v fck

Description : In a limit state method of design, when shear reinforcement is not provided, the calculated shear stress at the critical section of a slab shall not exceed; [ A ] Ks 0.25 v fck [ B ] ks 0.20 v fck [ C ] ks 0.16 v fck [ D ] ks 0.10 v fck

Last Answer : [ A ] Ks 0.25 v fck

In doubly reinforced rectangular beam, the allowatte stress in compression steel is___________the permissible stross intension insteel. (a) Greater than (b) Less than (c) Equal to (d) All of these

Description : In doubly reinforced rectangular beam, the allowatte stress in compression steel is___________the permissible stross intension insteel. (a) Greater than (b) Less than (c) Equal to (d) All of these

Last Answer : (b) Less than

In Limit state method of design, the factor of safety for concrete and steel respectively are [ A ] 3.00 and 1.80 [ B ] 1.50 and 1.18 [ C ] 1.50 and 1.15 [ D ] 1.50 and 1.50

Description : In Limit state method of design, the factor of safety for concrete and steel respectively are [ A ] 3.00 and 1.80 [ B ] 1.50 and 1.18 [ C ] 1.50 and 1.15 [ D ] 1.50 and 1.50

Last Answer : [ C ] 1.50 and 1.15

According to revised elastic theory, the steel in the compression zone is ------ that which is calculated simple elastic theory [ A ] equal to [ B ] less than [ C ] greater than [ D ] half of

Description : According to revised elastic theory, the steel in the compression zone is ------ that which is calculated simple elastic theory [ A ] equal to [ B ] less than [ C ] greater than [ D ] half of

Last Answer : [ C ] greater than

The centroid of compressive force, from the extreme compression fiber, in limit state design lies at a distance of (A) 0.367 xu (B) 0.416 xu (C) 0.446 xu (D) 0.573 xu Where xu is the depth of neutral axis at the limit state of collapse

Description : The centroid of compressive force, from the extreme compression fiber, in limit state design lies at a distance of (A) 0.367 xu (B) 0.416 xu (C) 0.446 xu (D) 0.573 xu Where xu is the depth of neutral axis at the limit state of collapse

Last Answer : Answer: Option B

The load stress of a section can be reduced by (A) Decreasing the lever arm (B) Increasing the total perimeter of bars (C) Replacing larger bars by greater number of small bars (D) Replacing smaller bars by greater number of greater bars

Description : The load stress of a section can be reduced by (A) Decreasing the lever arm (B) Increasing the total perimeter of bars (C) Replacing larger bars by greater number of small bars (D) Replacing smaller bars by greater number of greater bars

Last Answer : Answer: Option C

Regarding the working stress design of under reinforced concrete section, (a) The neutral axis depth will be greater than that of a balanced section. (b) The stress in steel intension will reach its maximum permissible value first. (c) The moment of resistance will be less than that of the balanced section. (d) The concrete on the tension side is also be considered for calculating the moment of resistance of the section.

Description : Regarding the working stress design of under reinforced concrete section, (a) The neutral axis depth will be greater than that of a balanced section. (b) The stress in steel intension will reach ... on the tension side is also be considered for calculating the moment of resistance of the section.

Last Answer : both b&c

The total resistance of a parallel circuit is always ____________. A. larger than the greatest branch resistance B. smaller than the lowest branch resistance C. equal to the sum of the individual branch resistances D. one-half the sum of the individual branch resistances

Description : The total resistance of a parallel circuit is always ____________. A. larger than the greatest branch resistance B. smaller than the lowest branch resistance C. equal to the sum of the individual branch resistances D. one-half the sum of the individual branch resistances

Last Answer : Answer: B

A clearance bearing is design accurately to keep the radius of journal and bearing equal. a) Journal radius is kept larger b) Journal radius is kept smaller c) True d) Can’t be determined

Description : A clearance bearing is design accurately to keep the radius of journal and bearing equal. a) Journal radius is kept larger b) Journal radius is kept smaller c) True d) Can’t be determined

Last Answer : b) Journal radius is kept smaller

In working stress method of design, permissible compressive bending stress for M20 grade concrete is given by [ A ] 5.0 N/mm2 [ B ] 7.0 N/mm2 [ C ] 10.0 N/mm2 [ D ] 20 N/mm2

Description : In working stress method of design, permissible compressive bending stress for M20 grade concrete is given by [ A ] 5.0 N/mm2 [ B ] 7.0 N/mm2 [ C ] 10.0 N/mm2 [ D ] 20 N/mm2

Last Answer : [ B ] 7.0 N/mm2

As per IS;456, in working stress method of design, permissible tensile stress for M20 grade concrete is given by [ A ] 1. 2 N/mm2 [ B ] 1.5 N/mm2 [ C ] 2.0 N/mm2 [ D ] 2.8 N/mm2

Description : As per IS;456, in working stress method of design, permissible tensile stress for M20 grade concrete is given by [ A ] 1. 2 N/mm2 [ B ] 1.5 N/mm2 [ C ] 2.0 N/mm2 [ D ] 2.8 N/mm2

Last Answer : [ D ] 2.8 N/mm2

In limit state design of concrete for flexure, the area of stress block is taken as (a) 0.530 fck. Xu (b) 0.446 fck . Xu ( c) 0.420 fck .Xu (d) 0.360 fck . Xu Where fck is characteristic compressive strength of concrete and Xu is the depth of neutral axis from top.

Description : In limit state design of concrete for flexure, the area of stress block is taken as (a) 0.530 fck. Xu (b) 0.446 fck . Xu ( c) 0.420 fck .Xu (d) 0.360 fck . Xu Where fck is characteristic compressive strength of concrete and Xu is the depth of neutral axis from top.

Last Answer : (d) 0.360 fck . Xu

The theoretical stress-strain curve of the concrete in the Limit State design of structures is correspondingly reduced by the factor [ A ] 0.35 [ B ] 0.5 [ C ] 0.67 [ D ] 0.75

Description : The theoretical stress-strain curve of the concrete in the Limit State design of structures is correspondingly reduced by the factor [ A ] 0.35 [ B ] 0.5 [ C ] 0.67 [ D ] 0.75

Last Answer : [ C ] 0.67

The theoretical stress-strain curve of the concrete in the Limit State design of structures is correspondingly reduced by the factor [ A ] 0.35 [ B ] 0.5 [ C ] 0.67 [ D ] 0.75

Description : The theoretical stress-strain curve of the concrete in the Limit State design of structures is correspondingly reduced by the factor [ A ] 0.35 [ B ] 0.5 [ C ] 0.67 [ D ] 0.75

Last Answer : [ C ] 0.67

According to the steel beam theory of doubly reinforced beams (A) Tension is resisted by tension steel (B) Compression is resisted by compression steel (C) Stress in tension steel equals the stress in compression steel (D) All the above

Description : According to the steel beam theory of doubly reinforced beams (A) Tension is resisted by tension steel (B) Compression is resisted by compression steel (C) Stress in tension steel equals the stress in compression steel (D) All the above

Last Answer : Answer: Option D

The compression in steel (fS) at failure for Fe - 415 grade steel using stress-strain curve shall be [ A ] 0.87 fy [ B ] 0.75 fy [ C ] 0.45 fy [ D ] 0.55 fy

Description : The compression in steel (fS) at failure for Fe - 415 grade steel using stress-strain curve shall be [ A ] 0.87 fy [ B ] 0.75 fy [ C ] 0.45 fy [ D ] 0.55 fy

Last Answer : [ B ] 0.75 fy

As per IS: 1139, permissible stress in compression steel reinforcement for High Yield strength deformed bars is [ A ] 140 N/mm2 [ B ] 190 N/mm2 [ C ] 230 N/mm2 [ D ] 415 N/mm2

Description : As per IS: 1139, permissible stress in compression steel reinforcement for High Yield strength deformed bars is [ A ] 140 N/mm2 [ B ] 190 N/mm2 [ C ] 230 N/mm2 [ D ] 415 N/mm2

Last Answer : [ B ] 190 N/mm2

Partial safety factor for strength in steel m Limit state design is [ A ] 1.15 [ B ] 1.25 [ C ] 1.5 [ D ] 1.65

Description : Partial safety factor for strength in steel m Limit state design is [ A ] 1.15 [ B ] 1.25 [ C ] 1.5 [ D ] 1.65

Last Answer : [ A ] 1.15

Partial safety factor for strength in steel m Limit state design is [ A ] 1.15 [ B ] 1.25 [ C ] 1.5 [ D ] 1.65

Description : Partial safety factor for strength in steel m Limit state design is [ A ] 1.15 [ B ] 1.25 [ C ] 1.5 [ D ] 1.65

Last Answer : [ A ] 1.15

In a singly reinforced beam, if the stress in concrete reaches its allowable limit later than the steel reaches, its permissible value, the beam section is said to be (a) Under-reinforced section (b) Over-reinforced section (c) Critical section (d) Balanced section

Description : In a singly reinforced beam, if the stress in concrete reaches its allowable limit later than the steel reaches, its permissible value, the beam section is said to be (a) Under-reinforced section (b) Over-reinforced section (c) Critical section (d) Balanced section

Last Answer : (b) Over-reinforced section

The compression ratio cannot be increased beyond certain limit as it results in a. auto-ignition of fuel b. detonation c. engine knocking d. all the above

Description : The compression ratio cannot be increased beyond certain limit as it results in a. auto-ignition of fuel b. detonation c. engine knocking d. all the above

Last Answer : ANSWER d. all the above

What fraction is larger than one-half but smaller than four-fifths?

Description : What fraction is larger than one-half but smaller than four-fifths?

Last Answer : 1/2 and 4/5 is the same as 5/10 and 8/10 and so the fraction needed is 6/10 or 7/10

When shear stress exceeds the permissible limit in a slab, then it is reduced by (A) Increasing the depth (B) Providing shear reinforcement (C) Using high strength steel (D) Using thinner bars but more in number

Description : When shear stress exceeds the permissible limit in a slab, then it is reduced by (A) Increasing the depth (B) Providing shear reinforcement (C) Using high strength steel (D) Using thinner bars but more in number

Last Answer : Answer: Option A

Consider the following salient points in a stress-strain curve of a mild steel bar: 1. Yield point 2. Braking point 3. Yield plateau 4 . Proportionality limit 5. Ultimate point The correct sequence in which they occur while testing the mild steel bar in tension from initial zero strain to failure is (a) 4, 1, 2, 3 and 5 (b) 1, 4, 3, 5 and 2 (c) 4, 1, 3, 5 and 2 (d) 1, 4, 2, 3 and 5

Description : Consider the following salient points in a stress-strain curve of a mild steel bar: 1. Yield point 2. Braking point 3. Yield plateau 4 . Proportionality limit 5. Ultimate point The correct sequence in which they occur while testing the mild ... , 5 and 2 (c) 4, 1, 3, 5 and 2 (d) 1, 4, 2, 3 and 5

Last Answer : (c) 4, 1, 3, 5 and 2

In Limit state design, the maximum working load that the structure has to withstand is called [ A ] Service load [ B ] Factored load [ C ] Characteristic load [ D ] Ultimate load

Description : In Limit state design, the maximum working load that the structure has to withstand is called [ A ] Service load [ B ] Factored load [ C ] Characteristic load [ D ] Ultimate load

Last Answer : [ C ] Characteristic load

In Limit state design, the maximum working load that the structure has to withstand is called [ A ] Service load [ B ] Factored load [ C ] Characteristic load [ D ] Ultimate load

Description : In Limit state design, the maximum working load that the structure has to withstand is called [ A ] Service load [ B ] Factored load [ C ] Characteristic load [ D ] Ultimate load

Last Answer : [ C ] Characteristic load

Limit state method of design has _________ major limit state conditions [ A ] one [ B ] two [ C ] three [ D ] four

Description : Limit state method of design has _________ major limit state conditions [ A ] one [ B ] two [ C ] three [ D ] four

Last Answer : [ B ] two

Limit state method of design has _________ major limit state conditions [ A ] one [ B ] two [ C ] three [ D ] four

Description : Limit state method of design has _________ major limit state conditions [ A ] one [ B ] two [ C ] three [ D ] four

Last Answer : [ B ] two

The usual percentages of clay and metal in cermet are: (A) 50%, 50% (B) 60%, 40% (C) 70%, 30% (D) 80%, 20%

Description : The usual percentages of clay and metal in cermet are: (A) 50%, 50% (B) 60%, 40% (C) 70%, 30% (D) 80%, 20%

Last Answer : Answer: Option D

How would you describe what multi-channel attribution does? A. Gives the conversion credit to the first click B. Assigns equal percentages for conversions to every step C. Accredits deserving touch points along the conversion journey D. Gives the conversion credit to the last click

Description : How would you describe what multi-channel attribution does? A. Gives the conversion credit to the first click B. Assigns equal percentages for conversions to every step C. Accredits deserving touch points along the conversion journey D. Gives the conversion credit to the last click

Last Answer : C. Accredits deserving touch points along the conversion journey

How would you describe what multi-channel attribution does? A. Gives the conversion credit to the first click B. Assigns equal percentages for conversions to every step C. Accredits deserving touch points along the conversion journey D. Gives the conversion credit to the last click

Description : How would you describe what multi-channel attribution does? A. Gives the conversion credit to the first click B. Assigns equal percentages for conversions to every step C. Accredits deserving touch points along the conversion journey D. Gives the conversion credit to the last click

Last Answer : C. Accredits deserving touch points along the conversion journe

Consider the following statements: Percentage of steel for balanced designed of a singly reinforced rectangular section by limit state method depends on (1) Characteristic strength of concrete (2) Yield strength of concrete (3) Modulus of elasticity of steel (4) Geometry of the section. Which of these statements are correct? (a) 2, 3 and 4 (b) 1, 3 and 4 (c) 1, 2 and 4 (d) 1, 2 and 3

Description : Consider the following statements: Percentage of steel for balanced designed of a singly reinforced rectangular section by limit state method depends on (1) Characteristic strength of concrete (2) Yield strength of concrete (3) Modulus of elasticity ... (b) 1, 3 and 4 (c) 1, 2 and 4 (d) 1, 2 and 3

Last Answer : 1,2,4

The base of a column is subjected to moment. If the intensity of bearing pressure due to axial load is equal to stress due to moment, then the bearing pressure between the base and the concrete is (a) Uniform compression throughout (b) Zero at one end and compression at the other end (c) Tension at one end and compression at the other end (d) Compression, verying as a parabolic profile

Description : The base of a column is subjected to moment. If the intensity of bearing pressure due to axial load is equal to stress due to moment, then the bearing pressure between the base and the concrete ... Tension at one end and compression at the other end (d) Compression, verying as a parabolic profile

Last Answer : (b) Zero at one end and compression at the other end

The equilibrium equation for the condition that tension will be equal to the compression is given by [ A ] Compression in concrete = Tension in steel [ B ] Compression in concrete + Compression in steel = Tension in steel [ C ] Compression in concrete = Compression in steel [ D ] None of the above

Description : The equilibrium equation for the condition that tension will be equal to the compression is given by [ A ] Compression in concrete = Tension in steel [ B ] Compression in concrete + Compression in steel = Tension in steel [ C ] Compression in concrete = Compression in steel [ D ] None of the above

Last Answer : [ B ] Compression in concrete + Compression in steel = Tension in steel

Steel beam theory is used for (A) Design of simple steel beams (B) Steel beams encased in concrete (C) Doubly reinforced beams ignoring compressive stress in concrete (D) Beams if shear exceeds 4 times allowable shear stress

Description : Steel beam theory is used for (A) Design of simple steel beams (B) Steel beams encased in concrete (C) Doubly reinforced beams ignoring compressive stress in concrete (D) Beams if shear exceeds 4 times allowable shear stress

Last Answer : Answer: Option C

Pick up the assumption for the design of a pre-stressed concrete member from the following: (A) A transverse plane section remains a plane after bending (B) During deformation limits, Hook's law is equally applicable to concrete as well as to steel (C) Variation of stress in reinforcement due to changes in external loading is negligible (D) All the above

Description : Pick up the assumption for the design of a pre-stressed concrete member from the following: (A) A transverse plane section remains a plane after bending (B) During deformation limits, Hook's ... of stress in reinforcement due to changes in external loading is negligible (D) All the above

Last Answer : Answer: Option D

Area of steel required per metre width of pavement for a length of 20 m for design wheel load 6300 kg and permissible stress in steel 1400 kg/cm2 , is (A) 70 kg/sq cm (B) 80 kg/sq cm (C) 90 kg/sq cm (D) 100 kg/sq cm

Description : Area of steel required per metre width of pavement for a length of 20 m for design wheel load 6300 kg and permissible stress in steel 1400 kg/cm2 , is (A) 70 kg/sq cm (B) 80 kg/sq cm (C) 90 kg/sq cm (D) 100 kg/sq cm

Last Answer : Answer: Option C

The design yield stress of steel according to IS: 4561978 is: (A) 0.37 fy (B) 0.57 fy (C) 0.67 fy (D) 0.87 fy Where fy is the characteristic yield strength of steel

Description : The design yield stress of steel according to IS: 4561978 is: (A) 0.37 fy (B) 0.57 fy (C) 0.67 fy (D) 0.87 fy Where fy is the characteristic yield strength of steel

Last Answer : Answer: Option D

The parabola is defined mathematically as a curve generated by a point that moves suchthat its distance from the focus is always__________the distance to the directrix a.larger than b.smaller than c.equal to d.none of the above

Description : The parabola is defined mathematically as a curve generated by a point that moves suchthat its distance from the focus is always__________the distance to the directrix a.larger than b.smaller than c.equal to d.none of the above

Last Answer : c.equal to

The total resistance of a parallel circuit is always ____________. A. larger than that of the branch with the greatest resistance B. smaller than that of the branch with the lowest resistance C. equal to the sum of the individual branch resistances D. equal to the sum of the individual branch resistances divided by the number of branches

Description : The total resistance of a parallel circuit is always ____________. A. larger than that of the branch with the greatest resistance B. smaller than that of the branch with the lowest resistance C ... resistances D. equal to the sum of the individual branch resistances divided by the number of branches

Last Answer : Answer: B

Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In small columns, local efficiency is larger than Murphree efficiency; in large columns local efficiency is smaller than Murphree efficiency (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s (D) The concentration and hydrodynamic boundary layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Description : Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In ... layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Last Answer : (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s

If a manager tries to form territories with equal sales potential, the territories will usually be unequal in geographic size; this will cause the salespersons with larger territories to A)develop larger income potentials. B)have to work longer and harder to generate a certain sales volume. C)work about the same amount, since potential is the same. D)have much larger sales than those salespeople with smaller territories.

Description : If a manager tries to form territories with equal sales potential, the territories will usually be unequal in geographic size; this will cause the salespersons with larger territories to A)develop ... potential is the same. D)have much larger sales than those salespeople with smaller territories.

Last Answer : B)have to work longer and harder to generate a certain sales volume.

In working stress design, permissible bond stress in the case of deformed bars is more than that in plain bars by (A) 10 % (B) 20 % (C) 30 % (D) 40 %

Description : In working stress design, permissible bond stress in the case of deformed bars is more than that in plain bars by (A) 10 % (B) 20 % (C) 30 % (D) 40 %

Last Answer : (D) 40 %