According to revised elastic theory, the steel in the compression zone is ------ that which is calculated simple elastic theory [ A ] equal to [ B ] less than [ C ] greater than [ D ] half of

According to revised elastic theory, the steel in the compression zone is ------ that which is calculated simple elastic theory
[ A ] equal to
[ B ] less than
[ C ] greater than
[ D ] half of
by

1 Answer

Answer :

[ C ] greater than
by

Related questions

According to steel Beam theory, stress in compressive steel is ------- stress in tension steel [ A ] less than [ B ] greater than [ C ] equal to [ D ] twice

Description : According to steel Beam theory, stress in compressive steel is ------- stress in tension steel [ A ] less than [ B ] greater than [ C ] equal to [ D ] twice

Last Answer : [ C ] equal to

In doubly reinforced rectangular beam, the allowatte stress in compression steel is___________the permissible stross intension insteel. (a) Greater than (b) Less than (c) Equal to (d) All of these

Description : In doubly reinforced rectangular beam, the allowatte stress in compression steel is___________the permissible stross intension insteel. (a) Greater than (b) Less than (c) Equal to (d) All of these

Last Answer : (b) Less than

If the depth of actual neutral axis of a doubly reinforced beam (A) Is greater than the depth of critical neutral axis, the concrete attains its maximum stress earlier (B) Is less than the depth of critical neutral axis, the steel in the tensile zone attains its maximum stress earlier (C) Is equal to the depth of critical neutral axis; the concrete and steel attain their maximum stresses simultaneously (D) All the above

Description : If the depth of actual neutral axis of a doubly reinforced beam (A) Is greater than the depth of critical neutral axis, the concrete attains its maximum stress earlier (B) Is less ... critical neutral axis; the concrete and steel attain their maximum stresses simultaneously (D) All the above

Last Answer : Answer: Option D

According to the steel beam theory of doubly reinforced beams (A) Tension is resisted by tension steel (B) Compression is resisted by compression steel (C) Stress in tension steel equals the stress in compression steel (D) All the above

Description : According to the steel beam theory of doubly reinforced beams (A) Tension is resisted by tension steel (B) Compression is resisted by compression steel (C) Stress in tension steel equals the stress in compression steel (D) All the above

Last Answer : Answer: Option D

In a singly reinforced beam (A) Compression is borne entirely by concrete (B) Steel possesses initial stresses when embedded in concrete (C) Plane sections transverse to the centre line of the beam before bending remain plane after bending (D) Elastic moduli for concrete and steel have different values within the limits of deformation of the beam

Description : In a singly reinforced beam (A) Compression is borne entirely by concrete (B) Steel possesses initial stresses when embedded in concrete (C) Plane sections transverse to the centre line ... Elastic moduli for concrete and steel have different values within the limits of deformation of the beam

Last Answer : Answer: Option C

Working stress method of design results in -------------- percentages of compression steel than that of a limit state method of design [ A ] Equal [ B ] Larger [ C ] Smaller [ D ] Half of the

Description : Working stress method of design results in -------------- percentages of compression steel than that of a limit state method of design [ A ] Equal [ B ] Larger [ C ] Smaller [ D ] Half of the

Last Answer : [ B ] Larger

In a doubly reinforced beam , steel reinforcement is provided in a (a) Tensile zone (b) Compression zone (c) Either (a) & (b) (d) Both (a) & (b)

Description : In a doubly reinforced beam , steel reinforcement is provided in a (a) Tensile zone (b) Compression zone (c) Either (a) & (b) (d) Both (a) & (b)

Last Answer : (d) Both (a) & (b)

The application of elastic theory to the beams is based on the assumption that (a) At any cross-section, plane sections before bending remain plane after bending (b) All tensile stresses are taken up by reinforcement alone and none by the concrete. (c) Steel reinforcement is free from initial stresses when it is embedded in concrete. (d) All of the above

Description : The application of elastic theory to the beams is based on the assumption that (a) At any cross-section, plane sections before bending remain plane after bending (b) All tensile stresses are taken ... reinforcement is free from initial stresses when it is embedded in concrete. (d) All of the above

Last Answer : (d) All of the above

Pick up the correct assumption of the theory of simple bending (A) The value of the Young's modulus is the same in tension as well as in compression (B) Transverse section of a beam remains plane before and after bending (C) The material of the beam is homogeneous and isotropic (D) All the above

Description : Pick up the correct assumption of the theory of simple bending  (A) The value of the Young's modulus is the same in tension as well as in compression  (B) Transverse section of a beam remains ... bending  (C) The material of the beam is homogeneous and isotropic  (D) All the above

Last Answer : (D) All the above

In a T-beam , the breadth of the rib is equal to the (a) Total thickness of the slab, including cover (b) Width of the portion of the beam in the compression zone (c) Width of the portion of the beam in the compression zone (d) All the above.

Description : In a T-beam , the breadth of the rib is equal to the (a) Total thickness of the slab, including cover (b) Width of the portion of the beam in the compression zone (c) Width of the portion of the beam in the compression zone (d) All the above.

Last Answer : (c) Width of the portion of the beam in the compression zone

When the distance between centers of two adjacent rivets connecting the members subjected to either compression or tension exceeds the maximum pitch, then the additional rivets which are not subjected to the calculated stresses are known as (a) Packing rivets (b) Long-grip rivets (c) Tacking rivets (d) Auxiliary rivets

Description : When the distance between centers of two adjacent rivets connecting the members subjected to either compression or tension exceeds the maximum pitch, then the additional rivets which are not subjected to the ... (a) Packing rivets (b) Long-grip rivets (c) Tacking rivets (d) Auxiliary rivets

Last Answer : (c) Tacking rivets

Select the correct statement (A) Elastic modulus of high tensile steel is nearly the same as that of mild steel (B) Elastic modulus of high tensile steel is more than that of mild steel (C) Carbon percentage in high carbon steel is less than that in mild steel (D) High tensile steel is cheaper than mild steel

Description : Select the correct statement (A) Elastic modulus of high tensile steel is nearly the same as that of mild steel (B) Elastic modulus of high tensile steel is more than that of mild steel (C) ... high carbon steel is less than that in mild steel (D) High tensile steel is cheaper than mild steel

Last Answer : Answer: Option A

The ratio of the thickness of web to that of flange of steel rolled structural beams and channels is (A) Less than 1 (B) Equal to 1 (C) Greater than 1 (D) Less than 1 in beams but greater than 1 in channels

Description : The ratio of the thickness of web to that of flange of steel rolled structural beams and channels is (A) Less than 1 (B) Equal to 1 (C) Greater than 1 (D) Less than 1 in beams but greater than 1 in channels

Last Answer : Answer: Option A

Pick up the correct statement from the following: (A) The moment of inertia is calculated about the axis about which bending takes place (B) If tensile stress is less than axial stress, the section experiences compressive stress (C) If tensile stress is equal to axial stress, the section experiences compressive stress (D) All the above

Description : Pick up the correct statement from the following:  (A) The moment of inertia is calculated about the axis about which bending takes place  (B) If tensile stress is less than axial ... tensile stress is equal to axial stress, the section experiences compressive stress  (D) All the above 

Last Answer : (D) All the above 

In general, the depth of slab should be ---------------- the minimum depth required for balanced section. [ A ] Equal to [ B ] Less than [ C ] Greater than [ D ] Half of

Description : In general, the depth of slab should be ---------------- the minimum depth required for balanced section. [ A ] Equal to [ B ] Less than [ C ] Greater than [ D ] Half of

Last Answer : [ C ] Greater than

Ratio of permissible stress in direct compression and bending compression is (A) Less than 1 (B) Between 1 and 1.5 (C) Between 1.5 and 2.0 (D) Greater

Description : Ratio of permissible stress in direct compression and bending compression is (A) Less than 1 (B) Between 1 and 1.5 (C) Between 1.5 and 2.0 (D) Greater than 2

Last Answer : Answer: Option A

The density of soil can be increased (A) By reducing the space occupied by air (B) By elastic compression of soil grains (C) By expelling water from pores (D) All the above

Description : The density of soil can be increased (A) By reducing the space occupied by air (B) By elastic compression of soil grains (C) By expelling water from pores (D) All the above

Last Answer : Answer: Option D

According to KBP revised radio code which airtime below is classified class D for AM stations? A. 6:00 AM to 12:00 NN B. 12:00 NN to 6:00 PM C. 9:00 PM to 12 Midnight D. 12:00 Midnight to 5:00 AM

Description : According to KBP revised radio code which airtime below is classified class D for AM stations? A. 6:00 AM to 12:00 NN B. 12:00 NN to 6:00 PM C. 9:00 PM to 12 Midnight D. 12:00 Midnight to 5:00 AM

Last Answer : D. 12:00 Midnight to 5:00 AM

In a simple bending theory, one of the assumption is that the material of the beam is isotropic. This assumption means that the a. normal stress remains constant in all directions b. normal stress varies linearly in the material c. elastic constants are same in all the directions d. elastic constants varies linearly in the material

Description : In a simple bending theory, one of the assumption is that the material of the beam is isotropic. This assumption means that the a. normal stress remains constant in all directions b. ... c. elastic constants are same in all the directions d. elastic constants varies linearly in the material

Last Answer : c. elastic constants are same in all the directions

Terzaghi's analysis assumes: (A) Soil is homogeneous and isotropic (B) Elastic zone has straight boundaries inclined at = to the horizontal and plastic zones fully developed (C) Failure zones do not extend above the horizontal plane through the base of the footing (D) All the above

Description : Terzaghi's analysis assumes: (A) Soil is homogeneous and isotropic (B) Elastic zone has straight boundaries inclined at = to the horizontal and plastic zones fully developed (C) Failure zones do not extend above the horizontal plane through the base of the footing (D) All the above

Last Answer : Answer: Option D

The equilibrium equation for the condition that tension will be equal to the compression is given by [ A ] Compression in concrete = Tension in steel [ B ] Compression in concrete + Compression in steel = Tension in steel [ C ] Compression in concrete = Compression in steel [ D ] None of the above

Description : The equilibrium equation for the condition that tension will be equal to the compression is given by [ A ] Compression in concrete = Tension in steel [ B ] Compression in concrete + Compression in steel = Tension in steel [ C ] Compression in concrete = Compression in steel [ D ] None of the above

Last Answer : [ B ] Compression in concrete + Compression in steel = Tension in steel

Steel beam theory is used for (A) Design of simple steel beams (B) Steel beams encased in concrete (C) Doubly reinforced beams ignoring compressive stress in concrete (D) Beams if shear exceeds 4 times allowable shear stress

Description : Steel beam theory is used for (A) Design of simple steel beams (B) Steel beams encased in concrete (C) Doubly reinforced beams ignoring compressive stress in concrete (D) Beams if shear exceeds 4 times allowable shear stress

Last Answer : Answer: Option C

In the zone of R.C.C. beam where shear stress is less than 5 kg/cm2 , nominal reinforcement is provided at a pitch of (A) One-half lever arm of the section (B) One-third lever arm of the section (C) Lever arm of the section (D) One and half lever arm of the section

Description : In the zone of R.C.C. beam where shear stress is less than 5 kg/cm2 , nominal reinforcement is provided at a pitch of (A) One-half lever arm of the section (B) One-third lever arm of the section (C) Lever arm of the section (D) One and half lever arm of the section

Last Answer : Answer: Option C

As per revised Govt policy the insurant will get approximately a) Less than 40% of total premia paid by him, if surrendered before completion of 5 years b) 75% after completion of 5 years but before 10 years c) Full recovered amount after 10 year d) All the above

Description : As per revised Govt policy the insurant will get approximately a) Less than 40% of total premia paid by him, if surrendered before completion of 5 years b) 75% after completion of 5 years but before 10 years c) Full recovered amount after 10 year d) All the above

Last Answer : d) All the above

Consider the following statements: (a) Revised simplex method requires lesser computations than the simplex method. (b) Revised simplex method automatically generates the inverse of the current basis matrix. (c) Less number of entries are needed in each table of revised simplex method than usual simplex method. Which of these statements are correct? (A) (a) and (b) only (B) (a) and (c) only (C) (b) and (c) only (D) (a), (b) and (c)

Description : Consider the following statements: (a) Revised simplex method requires lesser computations than the simplex method. (b) Revised simplex method automatically generates the inverse of the current basis matrix. (c) Less number of entries are needed ... c) only (C) (b) and (c) only (D) (a), (b) and (c)

Last Answer : (D) (a), (b) and (c)

According to IS:456, the diameter of the helices in circular a column shall be at least [ A ] The diameter of longitudinal steel [ B ] One-half the diameter of longitudinal steel [ C ] One-fourth the diameter of longitudinal steel [ D ] Three-fourth the diameter of longitudinal steel

Description : According to IS:456, the diameter of the helices in circular a column shall be at least [ A ] The diameter of longitudinal steel [ B ] One-half the diameter of longitudinal steel [ C ] One-fourth the diameter of longitudinal steel [ D ] Three-fourth the diameter of longitudinal steel

Last Answer : [ C ] One-fourth the diameter of longitudinal steel

Due to change in price level, a revised estimate is prepared if the sanctioned estimate exceeds (A) 2.0 % (B) 2.5 % (C) 4.0 % (D) 5.0 %

Description : Due to change in price level, a revised estimate is prepared if the sanctioned estimate exceeds (A) 2.0 % (B) 2.5 % (C) 4.0 % (D) 5.0 %

Last Answer : (D) 5.0 %

Metal Steel is more elastic than rubber because _____. A. Its density is high B. It is a metal C. Ratio of stress to strain is more D. Ratio of stress to strain is less

Description : Metal Steel is more elastic than rubber because _____. A. Its density is high B. It is a metal C. Ratio of stress to strain is more D. Ratio of stress to strain is less

Last Answer : ANSWER: C

Steel is more elastic than rubber because _____. A. Its density is high B. It is a metal C. Ratio of stress to strain is more D. Ratio of stress to strain is less

Description : Steel is more elastic than rubber because _____. A. Its density is high B. It is a metal C. Ratio of stress to strain is more D. Ratio of stress to strain is less

Last Answer : ANSWER: C

For a slab supported on its four edges with corners held down and loaded uniformly, the Marcus correction factor to the moments obtained by Grashoff Rankine's theory (A) Is always less than 1 (B) Is always greater than 1 (C) Can be more than 1 (D) Can be less than 1

Description : For a slab supported on its four edges with corners held down and loaded uniformly, the Marcus correction factor to the moments obtained by Grashoff Rankine's theory (A) Is always less than 1 (B) Is always greater than 1 (C) Can be more than 1 (D) Can be less than 1

Last Answer : Answer: Option A

Total strain energy theory for the failure of a material at elastic limit, is known (A) Guest's or Trecas' theory (B) St. Venant's theory (C) Rankine's theory (D) Haig's theory

Description : Total strain energy theory for the failure of a material at elastic limit, is known  (A) Guest's or Trecas' theory  (B) St. Venant's theory  (C) Rankine's theory  (D) Haig's theory 

Last Answer : (D) Haig's theory 

Shear strain energy theory for the failure of a material at elastic limit, is due to (A) Rankine (B) Guest or Trecas (C) St. Venant (D) Von Mises

Description : Shear strain energy theory for the failure of a material at elastic limit, is due to  (A) Rankine  (B) Guest or Trecas  (C) St. Venant  (D) Von Mises

Last Answer : (D) Von Mises

Maximum shear stress theory for the failure of a material at the elastic limit, is known (A) Guest's or Trecas' theory (B) St. Venant's theory (C) Rankine's theory (D) Haig's theory

Description : Maximum shear stress theory for the failure of a material at the elastic limit, is known  (A) Guest's or Trecas' theory  (B) St. Venant's theory  (C) Rankine's theory  (D) Haig's theory

Last Answer : (A) Guest's or Trecas' theory

Maximum strain theory for the failure of a material at the elastic limit, is known as (A) Guest's or Trecas' theory (B) St. Venant's theory (C) Rankine's theory (D) Haig's theory

Description : Maximum strain theory for the failure of a material at the elastic limit, is known as  (A) Guest's or Trecas' theory  (B) St. Venant's theory  (C) Rankine's theory  (D) Haig's theory 

Last Answer : (B) St. Venant's theory

Maximum principal stress theory for the failure of a material at elastic point, is known (A) Guest's or Trecas' theory (B) St. Venant's theory (C) Rankine's theory (D) Von Mises' theory

Description : Maximum principal stress theory for the failure of a material at elastic point, is known  (A) Guest's or Trecas' theory  (B) St. Venant's theory  (C) Rankine's theory  (D) Von Mises' theory

Last Answer : (C) Rankine's theory 

Yield line theory results in [ A ] Elastic solution [ B ] Lower bound solution [ C ] Upper bound solution [ D ] Unique solution

Description : Yield line theory results in [ A ] Elastic solution [ B ] Lower bound solution [ C ] Upper bound solution [ D ] Unique solution

Last Answer : [ B ] Lower bound solution

According to IS:456-2000, the minimum slenderness ratio for a short column is [ A ] Less than 12 [ B ] Between 12 and 18 [ C ] Less than 18 [ D ] Must be greater than 18

Description : According to IS:456-2000, the minimum slenderness ratio for a short column is [ A ] Less than 12 [ B ] Between 12 and 18 [ C ] Less than 18 [ D ] Must be greater than 18

Last Answer : [ A ] Less than 12

According to IS:456-2000, the minimum eccentricity in no case [ A ] Shall be not less than 20mm [ B ] Shall be not greater than 30mm [ C ] Shall be 20mm-30mm [ D ] None of the above

Description : According to IS:456-2000, the minimum eccentricity in no case [ A ] Shall be not less than 20mm [ B ] Shall be not greater than 30mm [ C ] Shall be 20mm-30mm [ D ] None of the above

Last Answer : [ A ] Shall be not less than 20mm

The compressibility of clays is caused due to: (A) Expulsion of double layer water from in between the grains (B) Sliping of particles to new positions of greater density (C) Bending of particles as elastic sheets (D) All the above

Description : The compressibility of clays is caused due to: (A) Expulsion of double layer water from in between the grains (B) Sliping of particles to new positions of greater density (C) Bending of particles as elastic sheets (D) All the above

Last Answer : (D) All the above

Percentage of carbon content in mild steel is (A) Less than 0.25 (B) Between 0.25 and 0.7 (C) Between 0.7 and 1.5 (D) Greater than 1.5

Description : Percentage of carbon content in mild steel is (A) Less than 0.25 (B) Between 0.25 and 0.7 (C) Between 0.7 and 1.5 (D) Greater than 1.5

Last Answer : Answer: Option A

Regarding the working stress design of under reinforced concrete section, (a) The neutral axis depth will be greater than that of a balanced section. (b) The stress in steel intension will reach its maximum permissible value first. (c) The moment of resistance will be less than that of the balanced section. (d) The concrete on the tension side is also be considered for calculating the moment of resistance of the section.

Description : Regarding the working stress design of under reinforced concrete section, (a) The neutral axis depth will be greater than that of a balanced section. (b) The stress in steel intension will reach ... on the tension side is also be considered for calculating the moment of resistance of the section.

Last Answer : both b&c

cylindrical rod subjected to a tensile strain within the elastic limit undergoes a volume change. If the volume strain is equal to half the tensile strain, then the Poisson's ratio of the rod is (A) 0 (B) 0.33 (C) 0.44 (D) 0.25

Description : cylindrical rod subjected to a tensile strain within the elastic limit undergoes a volume change. If the volume strain is equal to half the tensile strain, then the Poisson's ratio of the rod is (A) 0 (B) 0.33 (C) 0.44 (D) 0.25

Last Answer : Option C

The length of the lap in a compression member is kept greater than bar diameter x (Permissible stress in bar / Five times the bond stress) or (A) 12 bar diameters (B) 18 bar diameters (C) 24 bar diameters (D) 30 bar diameters

Description : The length of the lap in a compression member is kept greater than bar diameter x (Permissible stress in bar / Five times the bond stress) or (A) 12 bar diameters (B) 18 bar diameters (C) 24 bar diameters (D) 30 bar diameters

Last Answer : Answer: Option C

In a square and ground helical spring the effective number of turns is incresead by a. 1 b. 2 c. 1.5 d. 0 Ans: b 77. Frequency of the fluctuating load of helical compression spring should be a. lees than natural frequency of vibration b. twenty times the natural frequency of vibration c. slightly greater than the natural frequency d. twenty times less than the natural frequency of vibration

Description : In a square and ground helical spring the effective number of turns is incresead by a. 1 b. 2 c. 1.5 d. 0 Ans: b 77. Frequency of the fluctuating load of helical compression ... vibration c. slightly greater than the natural frequency d. twenty times less than the natural frequency of vibration

Last Answer : d. twenty times less than the natural frequency of vibration

The nurse anticipates that the physician will perform joint aspiration and wrapping with compression elastic dressing for which of the following musculoskeletal problems? a) Joint effusion The described treatments are used with joint effusions and hemarthrosis.

Description : The nurse anticipates that the physician will perform joint aspiration and wrapping with compression elastic dressing for which of the following musculoskeletal problems? a) Joint effusion The described ... of tissue due to insufficient blood supply and may be associated with steroid use.

Last Answer : a) Joint effusion The described treatments are used with joint effusions and hemarthrosis.

Pick out the correct statement. (A) Materials exhibiting high elasticity obey Hooke's law (B) The elastic behaviour of rubber under compression is the same as its behaviour under tension (C) The damping capacity of a material is due to its plastic deformation (D) The stress required to cause plastic flow in polycrystalline material is

Description : Pick out the correct statement. (A) Materials exhibiting high elasticity obey Hooke's law (B) The elastic behaviour of rubber under compression is the same as its behaviour under tension (C) ... to its plastic deformation (D) The stress required to cause plastic flow in polycrystalline material is

Last Answer : Option B

The assumption in the theory of bending of beams is: (A) Material is homogeneous (B) Material is isotropic (C) Young's modulus is same in tension as well as in compression (D) All the above

Description : The assumption in the theory of bending of beams is:  (A) Material is homogeneous  (B) Material is isotropic  (C) Young's modulus is same in tension as well as in compression  (D) All the above 

Last Answer : (D) All the above 

Under maximum shear stress theory, maximum shear stress is equal to (a) Allowable stress in tension (b) Allowable stress in compression (c) Allowable stress in shear (d) None

Description : Under maximum shear stress theory, maximum shear stress is equal to (a) Allowable stress in tension (b) Allowable stress in compression (c) Allowable stress in shear (d) None

Last Answer : (c) Allowable stress in shear

Under maximum principal stress theory, maximum principal stress is equal to (a) Allowable stress in tension (b) Allowable stress in compression (c) Allowable stress in shear (d) None

Description : Under maximum principal stress theory, maximum principal stress is equal to (a) Allowable stress in tension (b) Allowable stress in compression (c) Allowable stress in shear (d) None

Last Answer : (a) Allowable stress in tension